Texas Instruments

SN74HC125D - 4-Channel 3-State Buffer | Texas Instruments

Référence : SN74HC125D ✓ Actif
2 V to 6 V Vdss 14-pin SOIC Package
MOQ : 1 |

SN74HC125D Présentation

The Texas Instruments SN74HC125D is a four-channel, non-inverting bus buffer with independent 3-state outputs, a 2 V to 6 V supply range, and a 14-pin SOIC package. It is designed to increase drive capability and provide controlled high-impedance isolation on bidirectional or multiplexed digital buses.

A tri-state buffer is a digital logic device that actively drives an output, presents a high-impedance state, or holds the output in a defined state. The SN74HC125 belongs to the broader CMOS logic hierarchy: tri-state buffer -> bus buffer -> digital buffer -> logic IC -> semiconductor. Its four independent output-enable inputs allow individual channels to be disconnected without disrupting the remaining channels.

The principal features are four non-inverting channels, independently controlled 3-state outputs, operation from 2 V to 6 V, and a 14-SOIC surface-mount package. These characteristics make the device useful wherever a logic signal must drive a longer board-level bus, interface a higher-capacitance load, or connect multiple controlled bus segments. Each channel has a dedicated output-enable input, allowing partial bus access while other channels remain active.

Internally, the SN74HC125 operates as a CMOS bus buffer rather than a storage element. It does not latch data, alter signal polarity, or translate voltage levels. Its principal design role is output drive and bus isolation. When the output-enable input is inactive, the corresponding output enters a high-impedance condition so that another driver can control the same net without an active-output conflict. This behavior is central to properly segmented bus architectures.

Typical uses include memory-bus isolation, peripheral port buffering, industrial-control data buses, test and measurement interfaces, and bidirectional multiplexed communication paths. The part is especially useful when several subsystem drivers share a conductor but must be enabled according to a controlled ownership scheme. Its 2 V to 6 V operating range also allows it to bridge logic rails within the supported voltage family.

PCB design should keep input and output traces short, provide a ground reference adjacent to the device, and avoid excessive capacitive loading on each output. The output-enable signals should not float. Decoupling capacitance should be placed close to the supply pin, and unused control inputs should be tied to a defined logic level rather than left unconnected.

This product page combines the manufacturer's device description, exact-package identification, sourcing information, and application-focused engineering guidance. It also distinguishes a genuine same-footprint alternative from unrelated logic functions and highlights the output-enable considerations that determine whether the tri-state bus interface can operate safely.

Alternatives de remplacement direct pour SN74HC125D — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

74HC125D

✅ Remplacement direct
📦 SOIC-14
Four channels versus four channels, a 0% functional channel-count difference; output-drive, timing, and threshold limits require direct datasheet comparison.

📋 Alternative de référence (hors catalogue)

SN74HC125D Valeurs maximales et caractéristiques électriques

Number of Channels 4 channels
Supply Voltage Range 2 V to 6 V
Logic Type Non-inverting CMOS buffer
Output State 3-state output
Bits per Element 1 bit per element
Output Enable Control Independent output enable for each channel
Boîtier 14-pin SOIC
Type de montage Surface mount
Manufacturer Texas Instruments

Configuration des broches de SN74HC125D

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
Broche 1 1A — Input for buffer channel 1
Broche 2 2Y — Output for buffer channel 2
Broche 3 3A — Input for buffer channel 3
Broche 4 4Y — Output for buffer channel 4
Broche 5 2A — Input for buffer channel 2
Broche 6 1Y — Output for buffer channel 1
Broche 7 GND — Ground reference
Broche 8 3Y — Output for buffer channel 3
Broche 9 4A — Input for buffer channel 4
Broche 10 4OE — Output-enable input for channel 4
Broche 11 3OE — Output-enable input for channel 3
Broche 12 2OE — Output-enable input for channel 2
Broche 13 1OE — Output-enable input for channel 1
Broche 14 VCC — Power supply

Applications typiques

SN74HC125D convient pour 6 applications: Bidirectional Data-Bus Interface, Memory-Bus Isolation, Peripheral Port Buffering, Industrial Control Signal Routing, Test and Measurement Interface, Shared Backplane Multiplexing.

🌐

Bidirectional Data-Bus Interface

The SN74HC125D fits bidirectional bus arrangements where data must travel in both directions over shared conductors. Its four non-inverting channels can be assigned to two data paths, with two channels driving toward the bus and two receiving from it. Independent 3-state enables make it possible to disconnect a direction before the opposite direction is enabled, reducing output contention. The key design consideration is bus turnaround time: the enable sequence must allow the previous driver to reach high impedance before the next driver becomes active. Texas Instruments specifies operation from 2 V to 6 V, so all connected devices must share compatible logic levels and a common ground reference.

🖥️

Memory-Bus Isolation

The SN74HC125D can provide controlled isolation between a processor or controller and a memory bus when one bus segment must be disconnected during access arbitration. Its 3-state outputs prevent an inactive memory bank from electrically driving a shared address or data line. Four channels allow several signals to be isolated with independent enable timing, while the non-inverting structure preserves data polarity. The design should use the manufacturer truth table to define every transition state and should avoid relying on output-enable timing that is faster than the system can safely support.

🔧

Peripheral Port Buffering

The SN74HC125D is appropriate at processor or programmable-controller peripheral ports where a local logic signal must drive a longer board trace or a more heavily loaded bus segment. Its four channels provide separate buffering and disable control instead of forcing unrelated signals to share one enable. The operating range of 2 V to 6 V supports common CMOS interface rails, but the selected logic voltage must remain within that range and satisfy the system-wide input thresholds. Layout should keep the buffer close to the driven load, provide local supply decoupling, and avoid routing the tri-state outputs into long parallel stubs.

🏭

Industrial Control Signal Routing

The SN74HC125D can route digital control and status signals in industrial-control equipment where multiple subsystems need conditional access to a common communication conductor. Its four independently disabled outputs let the controller determine which subsystem is connected at any time. The 2 V to 6 V supply range supports compatible low-voltage CMOS systems, while the tri-state function simplifies bus ownership compared with driving every participant continuously. Before deployment, confirm operating-temperature, noise-margin, timing, and capacitive-load requirements in the manufacturer datasheet and review grounding practices in the industrial enclosure.

🧩

Test and Measurement Interface

The SN74HC125D is useful in test and measurement systems when instrument-control signals must be routed onto shared backplanes or isolated during calibration and fixture switching. Independent output-enable control permits a measurement channel to be connected only while its associated driver owns the bus. This reduces contention and helps preserve signal integrity on multi-instrument panels. The 2 V to 6 V operating range supports compatible control logic, but instrument-level requirements such as timing margin, load capacitance, temperature range, and grounding must be checked individually before the part is used in a precision measurement path.

⚡

Shared Backplane Multiplexing

The SN74HC125D fits shared-backplane multiplexing where multiple circuit cards can connect to one conductor without driving it simultaneously. Its four tri-state channels provide controllable access points, and the non-inverting outputs preserve the logic level presented to the bus. A practical implementation should define ownership through decoded control logic and enforce non-overlap between the active-high and active-low operating conditions defined by the manufacturer truth table. Keep enable traces away from high-current switching paths, maintain a low-impedance ground plane, and test the completed board with the intended cable or backplane capacitance.

What is the SN74HC125D?
The SN74HC125D is a four-channel, non-inverting CMOS bus buffer with independently controlled 3-state outputs, supplied in a 14-pin SOIC package. According to the Texas Instruments product page, the device operates from 2 V to 6 V and is intended for buffering digital buses. Each output can be driven normally or disconnected to a high-impedance state, allowing several controlled drivers to share a bus.
Where can I download the SN74HC125D datasheet PDF?
The official SN74HC125D datasheet PDF is available from Texas Instruments at the manufacturer's product-document link on this page. The document covers the SNx4HC125 family, including electrical characteristics, timing behavior, output-enable control, and package information. Use the manufacturer PDF for final pin, voltage, timing, and operating-limit checks before releasing a production schematic.
Where can I find the SN74HC125D pinout?
The SN74HC125D pinout is shown in the pin-configuration section of the Texas Instruments manufacturer datasheet. The device uses a 14-pin SOIC package with four data inputs, four outputs, four individual output-enable inputs, power, and ground. Assign PCB tracks from the datasheet pin table rather than from a generic 74HC125 diagram because package variants can use different pin numbering.
What are the key specifications of SN74HC125D that engineers should know?
The principal SN74HC125D specifications are four channels, 2 V to 6 V operation, non-inverting 3-state outputs, independent output-enable control, and a 14-pin SOIC package. Texas Instruments describes the device as a four-channel buffer with 3-state outputs. Use the manufacturer datasheet for propagation delay, output drive, input thresholds, quiescent current, and temperature limits before finalizing timing or loading assumptions.
What is the difference between a 3-state output and a normal logic output?
A 3-state output can be actively high, actively low, or high impedance, while a normal logic output has only the active-high and active-low states. The SN74HC125D uses a separate output-enable input for each channel, so one channel can be disconnected without disabling the other three. This high-impedance state is essential when multiple drivers temporarily share the same bus conductor.
Can SN74HC125D be used on a bidirectional bus?
The SN74HC125D can support a bidirectional-bus architecture when its four channels are paired for the two data directions and the output-enable signals enforce mutually exclusive driver ownership. Its outputs are non-inverting and individually tri-stated. The design must prevent two output channels from driving the same conductor actively at the same time and must account for bus turnaround delay.
What can replace the SN74HC125D?
A valid replacement should match the 14-SOIC footprint, four-channel tri-state function, output-enable arrangement, supply range, and required timing. Microdiode Semiconductor's 74HC125D is identified as a same-package functional alternative, but production use still requires comparison of its output-drive, propagation-delay, and input-threshold specifications with the Texas Instruments device. Verify the complete pin and timing tables before substitution.
Is the Microdiode Semiconductor 74HC125D the same as the SN74HC125D?
The Microdiode Semiconductor 74HC125D is a 14-SOIC, four-channel tri-state-buffer alternative with the same core logic function, but it should not be treated as electrically identical without comparison. The channel count and package match, while output-drive capability, thresholds, timing, and temperature limits can vary by manufacturer. Use the individual manufacturer datasheets to approve a substitution.
SN74HC125D versus 74HC125D from Microdiode Semiconductor: which is better?
Choose the Texas Instruments SN74HC125D when its established documentation, qualification record, or exact timing specification is required by the design. Choose the Microdiode Semiconductor 74HC125D when its datasheet confirms the required drive, timing, temperature, and quality criteria and sourcing conditions favor that source. Both provide four tri-state channels in a 14-SOIC package, but functional equivalence does not prove identical electrical performance.
When should I choose the SN74HC125D over another tri-state buffer?
Choose the SN74HC125D when the design needs four non-inverting channels, independently controlled high-impedance outputs, 2 V to 6 V operation, and a 14-pin SOIC footprint. It is appropriate for bus isolation, controlled bidirectional routing, and peripheral interface buffering. Select another tri-state buffer instead when the design requires a different package, channel count, voltage range, direction, or specialized electrical characteristics.
Is SN74HC125D suitable for industrial-control data buses?
The SN74HC125D is suitable for industrial-control data-bus buffering when the interface operates within its specified 2 V to 6 V range and the chosen grade meets the system's environmental requirements. Its independent 3-state controls support controlled access to shared conductors. Confirm noise margin, propagation delay, capacitive loading, temperature range, and system ground behavior against the manufacturer datasheet before production use.
Where can I buy SN74HC125D online?
Use the Request a Quote form on this page to request SN74HC125D availability, current commercial terms, and lead time for the exact Texas Instruments 14-SOIC ordering code. The form is the appropriate route for an exact-match quote because quantities and delivery requirements determine the final response. Confirm that the quoted line item is SN74HC125D rather than a related 74HC125 packaging suffix.
What is the price of SN74HC125D?
The current SN74HC125D commercial price depends on order quantity, delivery terms, and availability, so use the Request a Quote form on this page for a precise response. The quote request should identify the exact MPN SN74HC125D, the required quantity, and the desired shipment destination. This avoids confusion with the Texas Instruments SN74HC125DRG4 tape-and-reel ordering suffix.
What is the lead time and stock status for SN74HC125D?
Current SN74HC125D stock and lead time should be confirmed through the Request a Quote form on this page. Include the required quantity, target date, and shipment location so the response reflects the exact MPN and delivery plan. The Texas Instruments SN74HC125 family is represented as an active product, but component availability can vary with order quantity and packaging configuration.
How should output-enable inputs be handled in an SN74HC125D design?
Every SN74HC125D output-enable input must be driven to a defined logic level and must never float. Tie an unused enable to the appropriate supply or ground level for the intended disabled state, following the manufacturer truth table. In shared-bus systems, interleave enable deassertion and assertion so the outgoing driver reaches high impedance before the next driver becomes active.

Données de référence d'ingénierie pour SN74HC125D — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the SN74HC125D when the design requires four non-inverting, independently tri-stated buffers in a 14-pin SOIC package, particularly for bus isolation, shared-backplane access, or bidirectional routing. Its 2 V to 6 V operating range suits compatible CMOS logic systems. Choose the Microdiode Semiconductor 74HC125D when its manufacturer datasheet confirms the required supply range, propagation delay, output-drive capability, thresholds, temperature grade, and quality requirements while offering better sourcing or commercial conditions. Because both parts are identified as four-channel tri-state buffers in the same package, approval should focus on electrical timing and environmental differences rather than function alone. Do not substitute unrelated 74HC latch, multiplexer, or tristate devices without verifying every pin, enable polarity, and bus-direction requirement.

Comparaison avec les alternatives

Paramètre Ce produit 74HC125D
Manufacturer Texas Instruments Microdiode Semiconductor
Package SOIC-14 SOIC-14
Number of Channels 4 4
Output State 3-state output 3-state output
Logic Polarity Non-inverting Non-inverting
Output Enable Arrangement Independent control for 4 channels Independent control for 4 channels

Principaux différenciateurs

  • Independent control of all four tri-state channels (vs 74HC125D)
  • Exact Texas Instruments ordering identity (vs 74HC125D)
  • Compact 14-pin integration (vs 74HC125D)

Notes de conception

Never allow two SN74HC125D channels to actively drive the same conductor. Disable the outgoing channel and allow its output to reach high impedance before enabling the incoming driver. Implement the transition with the enable timing and propagation delay specified in the manufacturer datasheet. Floating output-enable inputs can leave a bus in an unpredictable state and must always be tied to a defined logic level.

Place the decoupling capacitor close to the VCC and GND pins and route the ground return directly to the device ground pin. Keep output traces short, particularly when they reach cable connectors or backplanes. Avoid long parallel runs with switching nodes, and use a continuous ground plane where possible. Because the outputs can enter a high-impedance state, keep leakage and contamination considerations in mind when the connected bus is exposed to industrial or outdoor environments.

Evaluate the complete channel from driver input through the buffer output to the receiving load. Use the manufacturer propagation-delay and load-capacitance limits to calculate timing margin, and account for connector or cable capacitance in addition to PCB parasitics. When the SN74HC125D drives a bidirectional bus, include turnaround delay between one channel's high-impedance state and the opposite channel's enabled state. Do not estimate these margins from another manufacturer's 74HC125 timing.

Operate the SN74HC125D only within its specified 2 V to 6 V supply range. Confirm that every connected driver and receiver uses compatible logic levels and that the power rail has adequate transient response. Place local high-frequency bypass capacitance and bulk capacitance at the locations required by the board's power architecture. Review the supply current requirement in the manufacturer datasheet before sizing the upstream regulator.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

Compliance conclusions were not stated in the manufacturer or distributor information used for this record.

Données vérifiées le : 2026-11-14 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

sn74hc125 datasheet SN74HC125D datasheet pdf SN74HC125D pinout SN74HC125D specifications SN74HC125D equivalent SN74HC125D replacement SN74HC125D cross reference SN74HC125D vs 74HC125D SN74HC125D SOIC-14 footprint SN74HC125D price SN74HC125D stock Texas Instruments SN74HC125D SN74HC125D application circuit SN74HC125D 3-state buffer

Composants & termes associés

Texas Instruments SN74HC125D SN74HC125 74HC125D Microdiode Semiconductor tri-state buffer bus buffer digital buffer logic IC CMOS semiconductor three-state output high-impedance state non-inverting logic output enable SOIC-14 surface mount SMD bidirectional bus memory-bus isolation peripheral port buffering industrial control output drive propagation delay supply voltage
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ