SN74HC125D - 4-Channel 3-State Buffer | Texas Instruments
부품 번호: SN74HC125D ✓ 활성SN74HC125D 개요
A tri-state buffer is a digital logic device that actively drives an output, presents a high-impedance state, or holds the output in a defined state. The SN74HC125 belongs to the broader CMOS logic hierarchy: tri-state buffer -> bus buffer -> digital buffer -> logic IC -> semiconductor. Its four independent output-enable inputs allow individual channels to be disconnected without disrupting the remaining channels.
The principal features are four non-inverting channels, independently controlled 3-state outputs, operation from 2 V to 6 V, and a 14-SOIC surface-mount package. These characteristics make the device useful wherever a logic signal must drive a longer board-level bus, interface a higher-capacitance load, or connect multiple controlled bus segments. Each channel has a dedicated output-enable input, allowing partial bus access while other channels remain active.
Internally, the SN74HC125 operates as a CMOS bus buffer rather than a storage element. It does not latch data, alter signal polarity, or translate voltage levels. Its principal design role is output drive and bus isolation. When the output-enable input is inactive, the corresponding output enters a high-impedance condition so that another driver can control the same net without an active-output conflict. This behavior is central to properly segmented bus architectures.
Typical uses include memory-bus isolation, peripheral port buffering, industrial-control data buses, test and measurement interfaces, and bidirectional multiplexed communication paths. The part is especially useful when several subsystem drivers share a conductor but must be enabled according to a controlled ownership scheme. Its 2 V to 6 V operating range also allows it to bridge logic rails within the supported voltage family.
PCB design should keep input and output traces short, provide a ground reference adjacent to the device, and avoid excessive capacitive loading on each output. The output-enable signals should not float. Decoupling capacitance should be placed close to the supply pin, and unused control inputs should be tied to a defined logic level rather than left unconnected.
This product page combines the manufacturer's device description, exact-package identification, sourcing information, and application-focused engineering guidance. It also distinguishes a genuine same-footprint alternative from unrelated logic functions and highlights the output-enable considerations that determine whether the tri-state bus interface can operate safely.
드롭인 대체품: SN74HC125D — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
74HC125D
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
SN74HC125D 최대 정격 & 전기적 특성
| Number of Channels | 4 channels |
| Supply Voltage Range | 2 V to 6 V |
| Logic Type | Non-inverting CMOS buffer |
| Output State | 3-state output |
| Bits per Element | 1 bit per element |
| Output Enable Control | Independent output enable for each channel |
| 패키지 | 14-pin SOIC |
| 실장 유형 | Surface mount |
| Manufacturer | Texas Instruments |
SN74HC125D 핀 구성
| 핀 1 | 1A — Input for buffer channel 1 |
| 핀 2 | 2Y — Output for buffer channel 2 |
| 핀 3 | 3A — Input for buffer channel 3 |
| 핀 4 | 4Y — Output for buffer channel 4 |
| 핀 5 | 2A — Input for buffer channel 2 |
| 핀 6 | 1Y — Output for buffer channel 1 |
| 핀 7 | GND — Ground reference |
| 핀 8 | 3Y — Output for buffer channel 3 |
| 핀 9 | 4A — Input for buffer channel 4 |
| 핀 10 | 4OE — Output-enable input for channel 4 |
| 핀 11 | 3OE — Output-enable input for channel 3 |
| 핀 12 | 2OE — Output-enable input for channel 2 |
| 핀 13 | 1OE — Output-enable input for channel 1 |
| 핀 14 | VCC — Power supply |
일반적인 애플리케이션
SN74HC125D 적합 용도: 6 애플리케이션s: Bidirectional Data-Bus Interface, Memory-Bus Isolation, Peripheral Port Buffering, Industrial Control Signal Routing, Test and Measurement Interface, Shared Backplane Multiplexing.
Bidirectional Data-Bus Interface
The SN74HC125D fits bidirectional bus arrangements where data must travel in both directions over shared conductors. Its four non-inverting channels can be assigned to two data paths, with two channels driving toward the bus and two receiving from it. Independent 3-state enables make it possible to disconnect a direction before the opposite direction is enabled, reducing output contention. The key design consideration is bus turnaround time: the enable sequence must allow the previous driver to reach high impedance before the next driver becomes active. Texas Instruments specifies operation from 2 V to 6 V, so all connected devices must share compatible logic levels and a common ground reference.
추천
Memory-Bus Isolation
The SN74HC125D can provide controlled isolation between a processor or controller and a memory bus when one bus segment must be disconnected during access arbitration. Its 3-state outputs prevent an inactive memory bank from electrically driving a shared address or data line. Four channels allow several signals to be isolated with independent enable timing, while the non-inverting structure preserves data polarity. The design should use the manufacturer truth table to define every transition state and should avoid relying on output-enable timing that is faster than the system can safely support.
추천
Peripheral Port Buffering
The SN74HC125D is appropriate at processor or programmable-controller peripheral ports where a local logic signal must drive a longer board trace or a more heavily loaded bus segment. Its four channels provide separate buffering and disable control instead of forcing unrelated signals to share one enable. The operating range of 2 V to 6 V supports common CMOS interface rails, but the selected logic voltage must remain within that range and satisfy the system-wide input thresholds. Layout should keep the buffer close to the driven load, provide local supply decoupling, and avoid routing the tri-state outputs into long parallel stubs.
추천
Industrial Control Signal Routing
The SN74HC125D can route digital control and status signals in industrial-control equipment where multiple subsystems need conditional access to a common communication conductor. Its four independently disabled outputs let the controller determine which subsystem is connected at any time. The 2 V to 6 V supply range supports compatible low-voltage CMOS systems, while the tri-state function simplifies bus ownership compared with driving every participant continuously. Before deployment, confirm operating-temperature, noise-margin, timing, and capacitive-load requirements in the manufacturer datasheet and review grounding practices in the industrial enclosure.
추천
Test and Measurement Interface
The SN74HC125D is useful in test and measurement systems when instrument-control signals must be routed onto shared backplanes or isolated during calibration and fixture switching. Independent output-enable control permits a measurement channel to be connected only while its associated driver owns the bus. This reduces contention and helps preserve signal integrity on multi-instrument panels. The 2 V to 6 V operating range supports compatible control logic, but instrument-level requirements such as timing margin, load capacitance, temperature range, and grounding must be checked individually before the part is used in a precision measurement path.
추천
Shared Backplane Multiplexing
The SN74HC125D fits shared-backplane multiplexing where multiple circuit cards can connect to one conductor without driving it simultaneously. Its four tri-state channels provide controllable access points, and the non-inverting outputs preserve the logic level presented to the bus. A practical implementation should define ownership through decoded control logic and enforce non-overlap between the active-high and active-low operating conditions defined by the manufacturer truth table. Keep enable traces away from high-current switching paths, maintain a low-impedance ground plane, and test the completed board with the intended cable or backplane capacitance.
추천
추천 제품 요약
엔지니어링 참조 데이터: SN74HC125D — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | 74HC125D |
|---|---|---|
| Manufacturer | Texas Instruments | Microdiode Semiconductor |
| Package | SOIC-14 | SOIC-14 |
| Number of Channels | 4 | 4 |
| Output State | 3-state output | 3-state output |
| Logic Polarity | Non-inverting | Non-inverting |
| Output Enable Arrangement | Independent control for 4 channels | Independent control for 4 channels |
주요 차별점
- Independent control of all four tri-state channels (vs 74HC125D)
- Exact Texas Instruments ordering identity (vs 74HC125D)
- Compact 14-pin integration (vs 74HC125D)
설계 노트
Never allow two SN74HC125D channels to actively drive the same conductor. Disable the outgoing channel and allow its output to reach high impedance before enabling the incoming driver. Implement the transition with the enable timing and propagation delay specified in the manufacturer datasheet. Floating output-enable inputs can leave a bus in an unpredictable state and must always be tied to a defined logic level.
Place the decoupling capacitor close to the VCC and GND pins and route the ground return directly to the device ground pin. Keep output traces short, particularly when they reach cable connectors or backplanes. Avoid long parallel runs with switching nodes, and use a continuous ground plane where possible. Because the outputs can enter a high-impedance state, keep leakage and contamination considerations in mind when the connected bus is exposed to industrial or outdoor environments.
Evaluate the complete channel from driver input through the buffer output to the receiving load. Use the manufacturer propagation-delay and load-capacitance limits to calculate timing margin, and account for connector or cable capacitance in addition to PCB parasitics. When the SN74HC125D drives a bidirectional bus, include turnaround delay between one channel's high-impedance state and the opposite channel's enabled state. Do not estimate these margins from another manufacturer's 74HC125 timing.
Operate the SN74HC125D only within its specified 2 V to 6 V supply range. Confirm that every connected driver and receiver uses compatible logic levels and that the power rail has adequate transient response. Place local high-frequency bypass capacitance and bulk capacitance at the locations required by the board's power architecture. Review the supply current requirement in the manufacturer datasheet before sizing the upstream regulator.
규정 준수 정보
Compliance conclusions were not stated in the manufacturer or distributor information used for this record.