SN74LS240M - 8-Channel 3-State Inverting Buffer | onsemi
Référence : SN74LS240M ✓ ActifSN74LS240M Présentation
A logic buffer is a digital integrated circuit that reproduces an input signal while providing buffering, isolation, and drive capability. A line driver strengthens digital signals for transmission across circuit-board traces or between logic sections. A bus transmitter combines that drive function with a three-state output, allowing the output to disconnect electrically when it is not selected. The SN74LS240M belongs to the 74LS bipolar logic family and is positioned within the hierarchy of logic integrated circuits, digital interface devices, and bus-oriented transmitters.
The principal features are eight individually controlled inverting outputs, 4.75 V to 5.25 V operating voltage, and three-state output operation. Inverting operation means a low input level produces a high output level, while a high input level produces a low output level. Input hysteresis helps improve noise margins by defining distinct transition regions near the switching threshold. The device is intended for memory-address driving, clock driving, and general bus-oriented signal transmission where higher board density is useful.
The SN74LS240M combines LS-series bipolar logic behavior with the practical benefits of a compact surface-mount package. Its inverting outputs are useful when a system requires complementary phase relationships or inversion between two logic stages. Because three-state outputs can be disabled, designers can prevent contention on shared data, address, or control buses by ensuring that only one driver is enabled during each transfer interval.
Typical uses include memory and peripheral interface logic, buffered clock distribution, industrial control boards, computer bus interfaces, and embedded systems requiring a compact octal bus transmitter. In a shared-bus arrangement, output-enable signals determine which driver owns the bus, while the other devices maintain high-impedance outputs. This arrangement reduces electrical loading and helps prevent simultaneous-output contention.
PCB design should provide a continuous ground plane, minimize return-current-loop area, and place input and output paths away from noisy switching nodes. Because the device is a bipolar logic part, supply and ground connections should be decoupled near the package, and unused inputs should be tied to a defined logic level rather than left floating. This page combines the device function, package information, replacement guidance, and practical interface considerations for faster engineering selection.
Alternatives de remplacement direct pour SN74LS240M — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
SN74LS240DM
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
SN74LS240M
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →SN74LS240A DM
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
SN74LS240A M
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
SN74LS240M Valeurs maximales et caractéristiques électriques
| Number of Channels | 8 channels |
| Channel Organization | 2 elements × 4 bits per element |
| Logic Type | Inverting buffer and line driver |
| Type de sortie | 3-state output |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Technology | Bipolar |
| Boîtier | SOEIAJ-20 surface-mount package |
| Nombre de broches | 20 pins |
| Type de montage | Surface mount |
| Input Hysteresis | Present |
Guide de configuration des broches du SN74LS240M soeiaj-20 surface-mount package
Configuration des broches du SN74LS240M (boîtier soeiaj-20 surface-mount package). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour SN74LS240M.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
SN74LS240M convient pour 6 applications: Memory Address Driving, Buffered Clock Distribution, Shared Peripheral Data Bus, Industrial Control Interface, Embedded System Bus Isolation, Digital Signal Fan-Out.
Memory Address Driving
The SN74LS240M is suitable for driving memory-address lines because it provides eight inverting, three-state outputs in a compact 20-pin surface-mount package. Its 4.75 V to 5.25 V operating range matches a 5 V TTL-style bus environment, while input hysteresis improves noise margins around logic transitions. When several address or expansion buffers share a bus, output-enable control can hold unused drivers in the high-impedance state and reduce loading. The design must also account for the intentional inversion between each input and output and ensure that only one driver is enabled on any shared node.
Recommandé
Buffered Clock Distribution
The SN74LS240M can distribute clock signals where inversion is acceptable and additional drive strength is useful. Each of its eight outputs is independently controlled through the three-state enable function, allowing unused clock paths to be disconnected. The 4.75 V to 5.25 V supply range supports conventional 5 V logic systems, and input hysteresis helps reduce response to noise near the switching threshold. Engineers should verify propagation-delay and transition requirements for the selected source before using multiple outputs on a shared clock node.
Recommandé
Shared Peripheral Data Bus
The SN74LS240M fits shared peripheral buses that require wired-connection capability without simultaneous-output contention. Each inverting output can be disabled, allowing the controller to connect one driver at a time while other devices present a high impedance to the same bus. The octal organization permits multiple byte-wide interfaces, and the compact SOEIAJ-20 package supports density-oriented boards. Firmware and hardware must maintain mutually exclusive output-enable timing, while the logic design must account for the deliberate input-to-output inversion.
Recommandé
Industrial Control Interface
The SN74LS240M can serve as a compact interface buffer in 5 V industrial control electronics, particularly where control lines originate from older TTL-compatible logic and require stronger drive or bus isolation. Its three-state outputs let a controller select one of several interfacing circuits without electrically loading every destination. Input hysteresis supports operation where signal traces pass near moderate switching noise. The exact temperature grade should be checked for the installation environment, and unused inputs should be tied to a defined logic level.
Recommandé
Embedded System Bus Isolation
The SN74LS240M is useful between embedded subsystems that share legacy 5 V control or peripheral buses and require local buffering. Eight inverting outputs can support multiple control signals in one device, while the three-state function allows isolation from a bus when the associated subsystem is inactive. Its surface-mount SOEIAJ-20 package helps conserve board area compared with a through-hole octal package. The interface should be designed with consistent enable defaults so an inactive or reset controller cannot contend with another driver.
Recommandé
Digital Signal Fan-Out
The SN74LS240M can fan out one-sided logic signals to multiple destinations when inversion is acceptable. Independent output-enable control provides flexibility for placing selected outputs in the high-impedance state, while the eight-channel organization reduces the number of packages needed for multi-bit interfaces. The 4.75 V to 5.25 V supply range places it in a 5 V logic environment, and the input hysteresis feature helps distinguish valid levels in the presence of moderate trace noise. Signal timing and fan-out loading must be checked against the manufacturer specifications.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour SN74LS240M — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | SN74LS240DM | SN74LS240M | SN74LS240A DM | SN74LS240A M |
|---|---|---|---|---|---|
| Package | SOEIAJ-20 | SOEIAJ-20 | SOEIAJ-20 | SOEIAJ-20 | SOEIAJ-20 |
| Brand | onsemi | onsemi | Texas Instruments | onsemi | Texas Instruments |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Logic Polarity | Inverting | Inverting | Inverting | Inverting | Inverting |
| Output Type | 3-state output | 3-state output | 3-state output | 3-state output | 3-state output |
| Logic Family | Bipolar LS series | Bipolar LS series | Bipolar LS series | Bipolar LS series | Bipolar LS series |
| Primary Applications | Memory-address, clock, and bus-oriented drivers | Memory-address, clock, and bus-oriented drivers | Memory-address, clock, and bus-oriented drivers | Memory-address, clock, and bus-oriented drivers | Memory-address, clock, and bus-oriented drivers |
Principaux différenciateurs
- Octal three-state inversion in one compact package (vs SN74LS244)
- Shared-bus compatibility (vs SN74LS240DM)
- Compact surface-mount implementation (vs SN74LS240N)
Notes de conception
Never allow two enabled SN74LS240M outputs to drive the same net simultaneously. Although the three-state outputs permit shared-bus wiring, overlapping enable intervals can create output contention, excess current, and undefined voltage levels. Define enable defaults so all drivers remain high impedance during reset and establish non-overlapping control timing in the system logic.
Assign all 20 physical pins from the manufacturer pin-description table for the exact package ordering code. The device combines data inputs, outputs, output-enable controls, supply, and ground on a small surface-mount footprint. Keep the ground connection short, use an uninterrupted ground plane, and avoid routing input and output traces beneath noisy switching or clock-return paths.
Account for inversion when connecting external circuits because every SN74LS240M output is the complement of its corresponding input. For shared nets, place the driver close enough to the receiving devices to limit trace capacitance, and maintain controlled enable sequencing. Confirm propagation delay, output levels, and drive-current limits against the manufacturer datasheet for the selected ordering variant.
Use a stable 5 V supply within the stated 4.75 V to 5.25 V range and decouple the device close to its supply and ground pins. Because bipolar LS logic can draw different current depending on output state and switching activity, a quiet supply helps prevent output noise from affecting downstream logic. Use the manufacturer input-current and power-consumption data for final rail sizing.
Informations de conformité
The available manufacturer and distributor information identifies the device and package but does not state its RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.