Texas Instruments

SN75123N - Dual TTL Line Driver | Texas Instruments

Référence : SN75123N ✓ Actif
5 V Vdss 16-pin PDIP Package
MOQ : 1 |

SN75123N Présentation

Texas Instruments SN75123N is a dual line driver designed for IBM System 360 input/output interfaces, standard TTL logic, and terminated coaxial-cable or twisted-pair lines. The device operates from a single 5 V supply, provides TTL-compatible inputs and outputs, and is offered in a 16-pin PDIP package. Its output stage reaches 3.11 V at a source current of -59.3 mA.

A line driver is a digital interface circuit that converts a logic-level input into a stronger output capable of driving a transmission line. The SN75123 belongs to the broader logic IC and interface IC hierarchy. Its low-impedance emitter-follower outputs provide bidirectional signal transfer into terminated lines, while the uncommitted output structure permits multiple drivers to share a party-line bus for wired-OR operation.

The principal benefits are the combination of dual-channel drive capability, standard-TTL compatibility, a single 5 V supply, and low-impedance emitter-follower outputs. The 3.11 V output level at -59.3 mA provides a concrete indication of the output drive capability. Because both channels share the same package and supply architecture, the SN75123N can serve dual-ended, paired, or independently terminated line-driver arrangements where TTL logic must interface with older computer-bus or communications equipment.

Technically, the emitter-follower architecture makes the output suitable for coax or twisted-pair termination rather than providing an actively isolated differential output. The uncommitted outputs support party-line operation, allowing several drivers to be connected to one line when only one channel is active at a time. Designers must ensure that inactive outputs are held in a defined state so that no driver contends with another device on the shared bus.

Typical applications include legacy computer-interface equipment, point-to-point coax links, twisted-pair links, instrumentation interfaces, and industrial control systems that use 5 V TTL signaling. The SN75123N is particularly relevant when upgrading or maintaining equipment designed around IBM System 360-era interface levels while retaining modern solid-state control logic.

For a new design, verify the complete pin assignment, output-state requirements, termination topology, and timing margins in the manufacturer datasheet before layout. If the board uses two separate line interfaces, place the device close enough to the line-driver circuitry to minimize exposure to coupled noise. A terminating network at the receiving end is generally required for reliable operation over longer cable runs.

This product guide combines the electrical function, package information, interface use cases, pinout-reference guidance, design cautions, and available replacement context. It also distinguishes the confirmed TTL and line-drive characteristics from parameters that require direct confirmation in the Texas Instruments documentation before a production design is released.

Alternatives de remplacement direct pour SN75123N — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec SN75123N (même facteur de forme et même empreinte).

SN75123P

✅ Remplacement direct ⚠️ Spécifications non vérifiées
📦 PDIP-16
Same 16-pin PDIP footprint and dual-driver function; temperature-grade designation differs by 1 suffix code, requiring confirmation of the maximum operating temperature.

📋 Alternative de référence (hors catalogue)

SN75123Y

✅ Remplacement direct ⚠️ Spécifications non vérifiées
📦 PDIP-16
Same 16-pin PDIP footprint and SN75123 dual-driver family; the Y grade differs by one temperature-class suffix code from the N grade.

📋 Alternative de référence (hors catalogue)

SN75123N Spécifications

Product Type Dual line driver
Number of Drivers 2 channels
Logic Compatibility Standard TTL
Tension d'alimentation 5 V
Output Architecture Low-impedance emitter-follower
Output State Uncommitted output
Output Voltage at IOH 3.11 V at -59.3 mA
Interface Target IBM System 360 input/output interface
Supported Line Type Terminated coaxial cable or twisted pair
Party-Line Operation Supported for wired-OR logic
Boîtier 16-pin PDIP
Type de montage Through-hole

Guide de configuration des broches du SN75123N 16-pin pdip

Configuration des broches du SN75123N (boîtier 16-pin pdip). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 16-pin pdip pour le SN75123N

Aucune donnée de brochage détaillée disponible pour SN75123N.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

SN75123N convient pour 6 applications: Legacy Computer Bus Interfaces, Point-to-Point Coaxial Links, Twisted-Pair Data Links, Party-Line Wired-OR Buses, Industrial Control Equipment Retrofits, Test and Measurement Equipment Interfaces.

🖥️

Legacy Computer Bus Interfaces

The SN75123N fits legacy computer-bus and peripheral interfaces that use 5 V TTL-compatible line signaling. Its two low-impedance emitter-follower channels can drive terminated coaxial or twisted-pair connections, while the uncommitted outputs permit compatible drivers to share a party-line bus. According to the Texas Instruments SN75123 datasheet, the device was specifically designed around IBM System 360 input/output interface requirements. In restoration or modernization work, the 16-pin PDIP package and dual-channel arrangement provide continuity with original socketed hardware. The designer should verify channel polarity, termination, and output-state requirements before connecting it to newer circuitry.

🌐

Point-to-Point Coaxial Links

The SN75123N is appropriate for point-to-point coaxial links requiring a 5 V TTL input and a stronger terminated-line output. Its low-impedance emitter-follower architecture can source a 3.11 V output level at -59.3 mA, according to the Texas Instruments SN75123 datasheet. Two independent channels allow separate control, status, or data paths to use identical interface circuitry. Cable termination must match the receiver and transmission-line environment, and routing should minimize susceptibility to coupled noise. Use the manufacturer timing and output-state information to establish valid operating margins.

🔧

Twisted-Pair Data Links

The SN75123N can drive terminated twisted-pair links when the source and receiver use compatible TTL-level signaling. Its two channels make it useful for paired data, control, or feedback paths, while the single 5 V supply simplifies legacy interface designs. The Texas Instruments SN75123 datasheet identifies low-impedance emitter-follower outputs and a 3.11 V output at -59.3 mA as important drive characteristics. Board implementation should include the proper line termination, controlled output states, and grounding that avoids common-mode current in the cable. Maximum data rate must be confirmed from the device timing characteristics.

🏭

Party-Line Wired-OR Buses

The SN75123N supports party-line operation because its outputs are uncommitted, allowing multiple compatible driver outputs to be wired together when only one channel actively sources the bus at a time. This makes it useful for legacy bus arbitration, shared interrupt, or distributed control arrangements. The Texas Instruments SN75123 datasheet highlights the low-impedance emitter-follower structure and wired-OR capability. Correct implementation requires guaranteed inactive output states and logic that prevents simultaneous sourcing. Add the intended line termination and validate contention behavior in the complete system rather than assuming ordinary push-pull behavior.

🏭

Industrial Control Equipment Retrofits

The SN75123N is useful when modernizing industrial control equipment that retains older 5 V line-driver sockets or wired-OR buses. Its dual channel count allows one package to serve two terminated connections, and its TTL compatibility simplifies interfacing to contemporary control logic. According to the Texas Instruments SN75123 datasheet, the device was created for IBM System 360-style interface levels and can drive coax or twisted-pair wiring. Engineers should compare the complete pin assignment, temperature range, output-state behavior, and timing requirements with the original equipment before approving the retrofit.

📡

Test and Measurement Equipment Interfaces

The SN75123N can serve older test and measurement equipment that exchanges control or status signals over terminated lines. Two driver channels support separate trigger, control, or synchronization paths while operating from a familiar 5 V supply. The Texas Instruments SN75123 datasheet confirms TTL compatibility, a 3.11 V output level at -59.3 mA, and suitability for coax or twisted-pair cabling. For instrumentation, preserve the documented output-state sequence, use a defined termination network, and isolate long cable runs as required. Check propagation delay and pulse-width limits before using the device for high-speed synchronization.

What is the SN75123N and what is its primary function?
The SN75123N is a Texas Instruments dual line driver in a 16-pin PDIP package. According to the Texas Instruments SN75123 datasheet, it meets IBM System 360 input/output interface requirements and is compatible with standard-TTL logic and supply-voltage levels. Each of its two channels uses a low-impedance emitter-follower output designed to drive terminated coaxial cable or twisted-pair lines, while the uncommitted output structure also permits party-line wired-OR operation.
What are the key specifications of SN75123N that engineers should know?
The SN75123N combines two line-driver channels, a single 5 V supply, standard-TTL compatibility, and low-impedance emitter-follower outputs in a 16-pin PDIP package. The Texas Instruments SN75123 datasheet identifies a 3.11 V output level at -59.3 mA source current and confirms suitability for terminated coaxial or twisted-pair lines. The device was designed around IBM System 360 interface requirements and supports uncommitted outputs for party-line wired-OR logic.
Where can I download the SN75123N datasheet PDF?
The SN75123N datasheet can be obtained from the official Texas Instruments product page or through the manufacturer's datasheet link. The manufacturer identifies the SN75123N as a 16-pin PDIP dual line driver operating from a single 5 V supply. Use the pin-description and electrical-characteristics tables for exact logic thresholds, propagation timing, current limits, and recommended operating conditions before completing a circuit design.
Where can I find the SN75123N pinout and package drawing?
The SN75123N pinout and mechanical package drawing are located in the pin-configuration and mechanical-data sections of the Texas Instruments SN75123 datasheet. The component is specified in a 16-pin PDIP package. Assign PCB connections directly from that package drawing rather than inferring a dual-driver pinout from a quad-driver device, because channel count, enable functions, and output arrangements can differ substantially among older line-driver families.
What supply voltage and logic standard does SN75123N use?
The SN75123N operates from a single 5 V supply and is compatible with standard-TTL logic. According to the Texas Instruments SN75123 datasheet, its low-impedance emitter-follower outputs can source 3.11 V at -59.3 mA. The same documentation describes compatibility with IBM System 360 input/output interface levels, allowing the driver to bridge older terminated-line equipment and conventional TTL control circuitry.
Where can I buy SN75123N online?
The SN75123N can be requested through the Request a Quote form on this page, which is the appropriate route for current commercial terms, stock confirmation, and lead time. The device is identified by Texas Instruments as a 16-pin PDIP dual line driver with a single 5 V supply. Request the exact SN75123N ordering designation rather than accepting a generic SN75123 variant without confirming its package, temperature grade, and sourcing status.
What is the current lead time for SN75123N?
Current SN75123N lead time and minimum-order quantity should be confirmed through the Request a Quote form on this page. The manufacturer product page identifies SN75123N as the 16-pin PDIP orderable variant of the dual line driver, but purchasing conditions can change independently of the technical product record. Include the required quantity, target delivery date, and assembly packaging requirements in the request for an actionable supply commitment.
Is SN75123N in stock?
Stock status for the exact SN75123N should be checked through the Request a Quote form on this page. The Texas Instruments product page confirms the 16-pin PDIP dual line-driver configuration, while current availability depends on the requested quantity and channel inventory. Request a firm availability confirmation for the full order rather than relying on a family-level listing for another SN75123 package or temperature-grade variant.
What can replace SN75123N with the same 16-pin PDIP footprint?
The closest confirmed same-family replacement candidate is the Texas Instruments SN75123P, which uses the same 16-pin PDIP package and remains within the SN75123 dual line-driver family. Its temperature-grade details must be confirmed before substitution, and a footprint match alone does not establish timing, output-current, or lifecycle equivalence. No fully documented cross-brand, pin-to-pin replacement was established, so any alternative should be validated against the manufacturer pin and electrical tables.
Is the SN75123N the same as an SN75174N line driver?
No, the SN75123N is a dual line driver, whereas the SN75174N is a four-channel line-driver family member. The SN75123N uses two low-impedance emitter-follower channels in a 16-pin PDIP package and supports party-line wired-OR operation. Replacing it with a quad driver would not generally preserve the original pin functions or channel mapping, so SN75174N should be treated as a functional reference rather than a drop-in replacement.
When should I choose SN75123N over an SN75123P replacement?
Choose SN75123N when the required product specification explicitly calls for the N-grade 16-pin PDIP variant and its operating limits match the equipment being maintained. Consider SN75123P only after checking the manufacturer ordering table and electrical data for its temperature grade and availability. The two parts share the SN75123 family and package format, but lifecycle, temperature range, and exact ordering conditions should determine which one is appropriate for a new or replacement design.
Is SN75123N suitable for coaxial-cable and twisted-pair interfaces?
The SN75123N is suitable for terminated coaxial-cable and twisted-pair interfaces because its low-impedance emitter-follower outputs are designed to drive those lines. According to the Texas Instruments SN75123 datasheet, the output stage provides a 3.11 V level at -59.3 mA and remains uncommitted for party-line use. The cable receiver, termination value, signal polarity, and maximum data rate must still be checked against the complete interface specification.
What is the best cross-brand equivalent for SN75123N?
No cross-brand drop-in equivalent for the SN75123N has been confirmed by the available manufacturer and cross-reference information. The target is a dual, 5 V TTL-compatible line driver in a 16-pin PDIP package with an uncommitted emitter-follower output, so a replacement must match both the physical pin functions and the output architecture. Treat generic RS-422 drivers as unsuitable substitutes until their pinout and electrical characteristics have been compared directly.
How does SN75123N compare with SN75174N for legacy bus equipment?
The SN75123N provides two driver channels, while the SN75174N family provides four, making the SN75174N useful when additional bus outputs are required but not a direct footprint replacement for the dual SN75123N. Both belong to older logic-interface families, but channel count and pin assignments determine board compatibility. For an existing SN75123N socket, the comparison should emphasize the two-channel 16-pin PDIP architecture and uncommitted output behavior rather than treating the parts as electrically identical.
What design considerations matter when using SN75123N on a party-line bus?
The SN75123N supports party-line operation, but the designer must ensure that only one driver sources a line at a time and that inactive outputs remain in a defined state. The Texas Instruments SN75123 datasheet describes low-impedance emitter-follower outputs with uncommitted structure for wired-OR logic. Check output-state truth values, termination, cable length, and contention behavior in the datasheet; otherwise two active channels can fight each other or produce invalid bus levels.

Données de référence d'ingénierie pour SN75123N — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the SN75123N when maintaining or reproducing a legacy 5 V TTL interface that uses a dual, 16-pin PDIP line driver, particularly for terminated coax, twisted-pair, or party-line connections. Its documented low-impedance emitter-follower output, 3.11 V level at -59.3 mA, and uncommitted wired-OR capability make it more appropriate than a generic modern transceiver when the original interface topology must be preserved. The SN75123P and SN75123Y are same-family socket candidates, but their temperature grades and ordering conditions must be confirmed against the equipment requirements. Do not select them merely because the package matches. Likewise, SN75174N and MC1488-family devices are useful references for design comparisons, but their different channel counts or output architectures make them unsuitable as direct replacements. For new equipment, verify timing, supply current, logic thresholds, and environmental limits from the manufacturer datasheet before committing the design.

Comparaison avec les alternatives

Paramètre Ce produit SN75123P SN75123Y
Package 16-pin PDIP 16-pin PDIP 16-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments
Product Type Dual line driver Dual line driver Dual line driver
Number of Channels 2 channels 2 channels 2 channels
Temperature Grade N grade P grade; exact limits require confirmation Y grade; exact limits require confirmation

Principaux différenciateurs

  • Purpose-built dual line-driver architecture (vs SN75174N)
  • Specified output drive level (vs MC1488NE4)
  • Native party-line capability (vs MC1489NG4)

Notes de conception

Do not treat SN75123N as a conventional push-pull bus transceiver. The Texas Instruments SN75123 datasheet describes uncommitted emitter-follower outputs intended for terminated lines and party-line wired-OR use. Ensure that inactive channels remain in a defined state and that system logic prevents two outputs from sourcing the same line simultaneously. Review the truth table and output-current limits before adding drivers to an existing bus.

Keep the SN75123N close to the line-driver pins, input logic, and termination components, and route the driven conductors away from sensitive analog or clock traces. The through-hole PDIP package permits a conventional radial layout, but lead inductance and long branches can degrade edge behavior at high data rates. Use a continuous ground reference, place the supply bypass capacitor close to the device, and verify the cable-return connection in the interface layout.

Select the cable termination from the receiver specification and the actual line impedance rather than applying a generic resistor value. The SN75123N uses low-impedance emitter-follower outputs, so termination affects output level, rise time, and power dissipation. Confirm that the 3.11 V output level specified at -59.3 mA remains valid with the chosen network and load. For long cables, consider repeaters or isolation rather than extending the logic-level signal beyond its intended environment.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The available product information does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this legacy logic-interface device because no automotive qualification is identified.

Données vérifiées le : 2026-11-09 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

SN75123N datasheet SN75123N datasheet pdf SN75123N pinout SN75123N schematic Texas Instruments SN75123N SN75123N 16 pin PDIP SN75123N dual TTL line driver SN75123N 5V output SN75123N coaxial cable driver SN75123N twisted pair interface SN75123N replacement SN75123N equivalent SN75123N vs SN75174N SN75123N price SN75123N stock

Composants & termes associés

Texas Instruments SN75123N SN75123P SN75123Y SN75174N MC1488NE4 MC1489NG4 dual line driver line driver digital interface IC logic IC interface IC TTL standard TTL logic emitter-follower output low-impedance output uncommitted output wired-OR logic party-line operation IBM System 360 coaxial cable twisted pair PDIP-16 through-hole package 5 V supply
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ