SN75123N - Dual TTL Line Driver | Texas Instruments
MPN: SN75123N ✓ Hoạt độngSN75123N Tóm tắt
A line driver is a digital interface circuit that converts a logic-level input into a stronger output capable of driving a transmission line. The SN75123 belongs to the broader logic IC and interface IC hierarchy. Its low-impedance emitter-follower outputs provide bidirectional signal transfer into terminated lines, while the uncommitted output structure permits multiple drivers to share a party-line bus for wired-OR operation.
The principal benefits are the combination of dual-channel drive capability, standard-TTL compatibility, a single 5 V supply, and low-impedance emitter-follower outputs. The 3.11 V output level at -59.3 mA provides a concrete indication of the output drive capability. Because both channels share the same package and supply architecture, the SN75123N can serve dual-ended, paired, or independently terminated line-driver arrangements where TTL logic must interface with older computer-bus or communications equipment.
Technically, the emitter-follower architecture makes the output suitable for coax or twisted-pair termination rather than providing an actively isolated differential output. The uncommitted outputs support party-line operation, allowing several drivers to be connected to one line when only one channel is active at a time. Designers must ensure that inactive outputs are held in a defined state so that no driver contends with another device on the shared bus.
Typical applications include legacy computer-interface equipment, point-to-point coax links, twisted-pair links, instrumentation interfaces, and industrial control systems that use 5 V TTL signaling. The SN75123N is particularly relevant when upgrading or maintaining equipment designed around IBM System 360-era interface levels while retaining modern solid-state control logic.
For a new design, verify the complete pin assignment, output-state requirements, termination topology, and timing margins in the manufacturer datasheet before layout. If the board uses two separate line interfaces, place the device close enough to the line-driver circuitry to minimize exposure to coupled noise. A terminating network at the receiving end is generally required for reliable operation over longer cable runs.
This product guide combines the electrical function, package information, interface use cases, pinout-reference guidance, design cautions, and available replacement context. It also distinguishes the confirmed TTL and line-drive characteristics from parameters that require direct confirmation in the Texas Instruments documentation before a production design is released.
Bộ thay thế dễ dàng lắp đặt cho SN75123N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với SN75123N (cùng hình factor và footprint).
SN75123P
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SN75123Y
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SN75123N Thông số kỹ thuật
| Product Type | Dual line driver |
| Number of Drivers | 2 channels |
| Logic Compatibility | Standard TTL |
| Điện áp cung cấp | 5 V |
| Output Architecture | Low-impedance emitter-follower |
| Output State | Uncommitted output |
| Output Voltage at IOH | 3.11 V at -59.3 mA |
| Interface Target | IBM System 360 input/output interface |
| Supported Line Type | Terminated coaxial cable or twisted pair |
| Party-Line Operation | Supported for wired-OR logic |
| Hộp | 16-pin PDIP |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân SN75123N 16-pin pdip
Cấu hình chân cho SN75123N (16-pin pdip gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho SN75123N.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SN75123N phù hợp cho 6 Áp dụngs: Legacy Computer Bus Interfaces, Point-to-Point Coaxial Links, Twisted-Pair Data Links, Party-Line Wired-OR Buses, Industrial Control Equipment Retrofits, Test and Measurement Equipment Interfaces.
Legacy Computer Bus Interfaces
The SN75123N fits legacy computer-bus and peripheral interfaces that use 5 V TTL-compatible line signaling. Its two low-impedance emitter-follower channels can drive terminated coaxial or twisted-pair connections, while the uncommitted outputs permit compatible drivers to share a party-line bus. According to the Texas Instruments SN75123 datasheet, the device was specifically designed around IBM System 360 input/output interface requirements. In restoration or modernization work, the 16-pin PDIP package and dual-channel arrangement provide continuity with original socketed hardware. The designer should verify channel polarity, termination, and output-state requirements before connecting it to newer circuitry.
Được đề xuất
Point-to-Point Coaxial Links
The SN75123N is appropriate for point-to-point coaxial links requiring a 5 V TTL input and a stronger terminated-line output. Its low-impedance emitter-follower architecture can source a 3.11 V output level at -59.3 mA, according to the Texas Instruments SN75123 datasheet. Two independent channels allow separate control, status, or data paths to use identical interface circuitry. Cable termination must match the receiver and transmission-line environment, and routing should minimize susceptibility to coupled noise. Use the manufacturer timing and output-state information to establish valid operating margins.
Được đề xuất
Twisted-Pair Data Links
The SN75123N can drive terminated twisted-pair links when the source and receiver use compatible TTL-level signaling. Its two channels make it useful for paired data, control, or feedback paths, while the single 5 V supply simplifies legacy interface designs. The Texas Instruments SN75123 datasheet identifies low-impedance emitter-follower outputs and a 3.11 V output at -59.3 mA as important drive characteristics. Board implementation should include the proper line termination, controlled output states, and grounding that avoids common-mode current in the cable. Maximum data rate must be confirmed from the device timing characteristics.
Được đề xuất
Party-Line Wired-OR Buses
The SN75123N supports party-line operation because its outputs are uncommitted, allowing multiple compatible driver outputs to be wired together when only one channel actively sources the bus at a time. This makes it useful for legacy bus arbitration, shared interrupt, or distributed control arrangements. The Texas Instruments SN75123 datasheet highlights the low-impedance emitter-follower structure and wired-OR capability. Correct implementation requires guaranteed inactive output states and logic that prevents simultaneous sourcing. Add the intended line termination and validate contention behavior in the complete system rather than assuming ordinary push-pull behavior.
Được đề xuất
Industrial Control Equipment Retrofits
The SN75123N is useful when modernizing industrial control equipment that retains older 5 V line-driver sockets or wired-OR buses. Its dual channel count allows one package to serve two terminated connections, and its TTL compatibility simplifies interfacing to contemporary control logic. According to the Texas Instruments SN75123 datasheet, the device was created for IBM System 360-style interface levels and can drive coax or twisted-pair wiring. Engineers should compare the complete pin assignment, temperature range, output-state behavior, and timing requirements with the original equipment before approving the retrofit.
Được đề xuất
Test and Measurement Equipment Interfaces
The SN75123N can serve older test and measurement equipment that exchanges control or status signals over terminated lines. Two driver channels support separate trigger, control, or synchronization paths while operating from a familiar 5 V supply. The Texas Instruments SN75123 datasheet confirms TTL compatibility, a 3.11 V output level at -59.3 mA, and suitability for coax or twisted-pair cabling. For instrumentation, preserve the documented output-state sequence, use a defined termination network, and isolate long cable runs as required. Check propagation delay and pulse-width limits before using the device for high-speed synchronization.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SN75123N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SN75123P | SN75123Y |
|---|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Dual line driver | Dual line driver | Dual line driver |
| Number of Channels | 2 channels | 2 channels | 2 channels |
| Temperature Grade | N grade | P grade; exact limits require confirmation | Y grade; exact limits require confirmation |
Bảo phân biệt quan trọng
- Purpose-built dual line-driver architecture (vsSN75174N)
- Specified output drive level (vsMC1488NE4)
- Native party-line capability (vsMC1489NG4)
Ghi chú thiết kế
Do not treat SN75123N as a conventional push-pull bus transceiver. The Texas Instruments SN75123 datasheet describes uncommitted emitter-follower outputs intended for terminated lines and party-line wired-OR use. Ensure that inactive channels remain in a defined state and that system logic prevents two outputs from sourcing the same line simultaneously. Review the truth table and output-current limits before adding drivers to an existing bus.
Keep the SN75123N close to the line-driver pins, input logic, and termination components, and route the driven conductors away from sensitive analog or clock traces. The through-hole PDIP package permits a conventional radial layout, but lead inductance and long branches can degrade edge behavior at high data rates. Use a continuous ground reference, place the supply bypass capacitor close to the device, and verify the cable-return connection in the interface layout.
Select the cable termination from the receiver specification and the actual line impedance rather than applying a generic resistor value. The SN75123N uses low-impedance emitter-follower outputs, so termination affects output level, rise time, and power dissipation. Confirm that the 3.11 V output level specified at -59.3 mA remains valid with the chosen network and load. For long cables, consider repeaters or isolation rather than extending the logic-level signal beyond its intended environment.
Thông tin tuân thủ
The available product information does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this legacy logic-interface device because no automotive qualification is identified.