STM32F334R8T7 - 72MHz Cortex-M4 MCU | STMicroelectronics
Référence : STM32F334R8T7 ✓ ActifSTM32F334R8T7 Présentation
A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, and peripherals into one package. The STM32F334R8T7 belongs to the STM32F3 family of 32-bit embedded processors and sits within the broader hierarchy of microcontroller, embedded processor, semiconductor, and electronic component. Its mixed-signal architecture allows digital control, analog measurement, and analog output functions to share one device.
Principal features include an Arm Cortex-M4 core operating at up to 72 MHz, 64 KB of Flash, and 16 KB of SRAM. The analog subsystem provides two ADCs and three DACs for sensor conditioning, monitoring, waveform generation, and industrial control. A CAN interface compliant with specifications 2.0A and 2.0B supports standard and extended data frames, with communication rates reaching 1 Mbit/s according to the manufacturer datasheet.
The device integrates a floating-point processing unit, making it suitable for embedded algorithms that would benefit from hardware-assisted floating-point arithmetic. Its 64-pin LQFP package exposes a broad mix of digital and analog connections while remaining compatible with conventional surface-mount assembly and inspection. The 64 KB Flash capacity provides a practical balance between firmware size and embedded cost for control-oriented products.
Typical uses include industrial sensor controllers, motor-control systems, CAN-connected equipment, compact data acquisition units, medical monitoring devices, and low-cost consumer electronics. The two ADCs support analog measurement, while the three DACs allow programmable voltage outputs for excitation, test, or signal-generation functions. CAN connectivity makes the MCU appropriate for distributed control networks requiring standard and extended frames.
Designers should preserve the voltage and decoupling requirements in the manufacturer datasheet, place supporting components close to the power pins, and route analog inputs away from fast-switching signals. Firmware should also verify operating limits, clock configuration, and analog calibration after power-up. The 64-pin footprint simplifies inspection, but analog performance still depends on careful grounding and reference design.
This page organizes the key MCU specifications, sourcing information, available drop-in comparisons, and practical design guidance into a focused engineering reference. It is intended to help designers evaluate the STM32F334R8T7 for mixed-signal embedded systems while keeping package, memory, analog, and communication requirements in view.
Alternatives de remplacement direct pour STM32F334R8T7 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec STM32F334R8T7 (même facteur de forme et même empreinte) — différant par Flash Memory, Package, SRAM.
STM32F334R8T6
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →STM32F334R8T7 Valeurs maximales et caractéristiques électriques
| Product Type | 32-bit Arm Cortex-M4 microcontroller |
| Maximum Core Frequency | 72 MHz |
| Flash Memory | 64 KB (64K x 8) |
| SRAM | 16 KB |
| ADC Count | 2 |
| DAC Count | 3 |
| CAN Maximum Bit Rate | 1 Mbit/s |
| CAN Standard | CAN 2.0A and CAN 2.0B |
| CAN Frame Support | 11-bit standard and 29-bit extended identifiers |
| Processor Core | Arm Cortex-M4 with floating-point unit |
| Boîtier | 64-LQFP, 10 mm x 10 mm |
| Nombre de broches | 64 pins |
| Type de montage | Surface mount |
Guide de configuration des broches du STM32F334R8T7 64-lqfp, 10 mm x 10 mm
Configuration des broches du STM32F334R8T7 (boîtier 64-lqfp, 10 mm x 10 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour STM32F334R8T7.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
STM32F334R8T7 convient pour 6 applications: Industrial Sensor Controller, CAN-Connected Control Module, Compact Data-Acquisition Unit, Precision Motor-Control Platform, Medical Monitoring Controller, Programmable Test and Signal Generator.
Industrial Sensor Controller
The STM32F334R8T7 fits industrial sensor controllers that require fast local processing alongside compact analog conversion. Its 72 MHz Arm Cortex-M4 core can execute control logic while two ADCs acquire sensor signals and three DACs provide programmable analog outputs for excitation, testing, or actuator control. The 64 KB Flash and 16 KB SRAM provide dedicated program and working memory without requiring a separate processor. Its 64-LQFP package also exposes the mixed-signal and digital resources needed for a practical industrial controller. Engineers should design the analog front end around the datasheet ADC and DAC characteristics, use a clean reference strategy, and isolate sensitive measurement paths from switching nodes.
Recommandé
CAN-Connected Control Module
The STM32F334R8T7 is appropriate for distributed CAN control modules because its controller supports CAN 2.0A and 2.0B frames with rates up to 1 Mbit/s. The 72 MHz Cortex-M4 core can handle protocol tasks, diagnostics, and local control, while two ADCs and three DACs add measurement and output capability without requiring separate mixed-signal devices. In an implementation, the MCU connects through a suitable CAN transceiver, and the PCB must provide correct termination and controlled differential routing. Firmware should include bus-off recovery, error counters, frame validation, and timing checks so a communications fault does not compromise the wider equipment.
Recommandé
Compact Data-Acquisition Unit
The STM32F334R8T7 can form the core of a compact data-acquisition unit requiring two analog inputs, three programmable analog outputs, and real-time digital processing. Its 72 MHz Cortex-M4 core and 16 KB SRAM support sampling control, scaling, filtering, and communication tasks, while 64 KB Flash accommodates embedded firmware and configuration data. The three DACs may generate test stimuli or programmable references for a controlled measurement system. To achieve useful results, designers should establish analog grounding, reference stability, input filtering, and calibration sequences directly from the manufacturer datasheet. Firmware should also define overload handling and distinguish valid measurements from out-of-range inputs.
Recommandé
Precision Motor-Control Platform
The STM32F334R8T7 suits compact motor-control platforms that need fast computation, mixed-signal feedback, and network communication in one component. Its 72 MHz Arm Cortex-M4 core with a floating-point unit supports real-time control calculations, while the two ADCs can monitor analog feedback signals and the three DACs can provide control or test outputs. CAN 2.0A and 2.0B support is useful in coordinated industrial motion systems. The 64-LQFP footprint provides access to a broad pin set while retaining a conventional surface-mount package. Power-stage design, isolation, current sensing, protection, and timing must be evaluated independently, since those external functions determine achievable motor performance and safety.
Recommandé
Medical Monitoring Controller
The STM32F334R8T7 can support compact medical monitoring controllers where sensor acquisition, local signal processing, and a reliable communications path are needed. Two ADCs provide the analog input resources, three DACs support calibration or controlled test outputs, and the 72 MHz Cortex-M4 core handles data conditioning and system tasks. CAN connectivity allows the controller to participate in a wired equipment network, although the final medical product may require additional communication and safety functions. Design work should address analog isolation, low-noise references, calibration, fault detection, and software validation. The MCU's general-purpose status does not itself establish medical-device certification or compliance.
Recommandé
Programmable Test and Signal Generator
The STM32F334R8T7 is well suited to programmable test equipment and low-bandwidth signal generation because it combines three DACs with a 72 MHz real-time processor. The DAC outputs can create controlled analog test signals, while the Cortex-M4 floating-point unit supports calculation, waveform shaping, and timing routines. Its 64 KB Flash and 16 KB SRAM allow embedded control functions without a separate host processor, and CAN can coordinate commands with larger systems. Practical performance depends on the DAC reference, output buffering, reconstruction filtering, and the analog output bandwidth required by the application. Use the manufacturer characteristic and application information to select those external components.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour STM32F334R8T7 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | STM32F334R8T6 |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | 64-LQFP (10x10) | 64-LQFP (10x10) |
| Processor Core | Arm Cortex-M4 | Arm Cortex-M4 |
| Maximum Core Frequency | 72 MHz | 72 MHz |
| Flash Memory | 64 KB | 64 KB |
| SRAM | 16 KB | 16 KB |
| ADC Count | 2 | 2 |
| DAC Count | 3 | 3 |
| CAN Support | CAN 2.0A and CAN 2.0B, up to 1 Mbit/s | CAN 2.0A and CAN 2.0B, up to 1 Mbit/s |
| Temperature-Grade Suffix | T7 | T6 |
Principaux différenciateurs
- Integrated mixed-signal resource set (vs STM32F334R8T6)
- Real-time processing with floating-point hardware (vs STM32F334R8T6)
- Integrated CAN 2.0A and 2.0B communications (vs STM32F334R8T6)
Notes de conception
Decouple each supply group with the capacitance and placement specified in the manufacturer datasheet. Keep the analog and digital grounding strategy consistent with the MCU's reference-design recommendations, and route supply current through low-impedance planes. Verify startup, minimum operating voltage, maximum supply level, and external regulator tolerance before selecting power components; the device's complete electrical limits are not summarized by its 72 MHz clock rating.
Place decoupling capacitors close to their associated power pins and provide a continuous ground reference beneath the LQFP footprint. Route analog inputs away from switching nodes, high-current motor paths, and CAN transceiver return currents. For mixed-signal boards, separate analog and digital return paths where the application permits and use a solid, low-impedance ground structure rather than fragmented planes.
Treat ADC and DAC signals as sensitive analog nets: use short traces, controlled source and load impedances, and shielding where radiated noise matters. Check sampling timing, reference stability, and the acquisition bandwidth implied by the operating clock. The two ADC and three DAC peripherals are useful building blocks, but their practical resolution and settling performance depend on the circuit surrounding the MCU.
Do not substitute a family member solely because its package matches. STM32F334R8T6 shares the 64-LQFP format and major resources, but the T6 and T7 ordering suffixes must be checked against the required temperature range. For CAN networks, also verify transceiver selection, termination, bit timing, error handling, and fault recovery. A successful footprint comparison does not replace complete electrical and firmware validation.
Informations de conformité
AEC-Q100 is not applicable to this general-purpose microcontroller ordering code. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product page or current material-compliance documentation.