STMicroelectronics

STM32F334R8T7 - 72MHz Cortex-M4 MCU | STMicroelectronics

MPN: STM32F334R8T7 ✓ Aktif
64-LQFP, 10 mm x 10 mm Package 72 MHz Speed 64 KB (64K x 8) Memory
MOQ: 1 |

STM32F334R8T7 Ringkasan

The STMicroelectronics STM32F334R8T7 is a 32-bit Arm Cortex-M4 microcontroller operating up to 72 MHz, with 64 KB of Flash memory, 16 KB of SRAM, two ADCs, three DACs, and a 64-pin LQFP package measuring 10 mm by 10 mm. It combines a floating-point processor core with mixed-signal peripherals for compact embedded control systems.

A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, and peripherals into one package. The STM32F334R8T7 belongs to the STM32F3 family of 32-bit embedded processors and sits within the broader hierarchy of microcontroller, embedded processor, semiconductor, and electronic component. Its mixed-signal architecture allows digital control, analog measurement, and analog output functions to share one device.

Principal features include an Arm Cortex-M4 core operating at up to 72 MHz, 64 KB of Flash, and 16 KB of SRAM. The analog subsystem provides two ADCs and three DACs for sensor conditioning, monitoring, waveform generation, and industrial control. A CAN interface compliant with specifications 2.0A and 2.0B supports standard and extended data frames, with communication rates reaching 1 Mbit/s according to the manufacturer datasheet.

The device integrates a floating-point processing unit, making it suitable for embedded algorithms that would benefit from hardware-assisted floating-point arithmetic. Its 64-pin LQFP package exposes a broad mix of digital and analog connections while remaining compatible with conventional surface-mount assembly and inspection. The 64 KB Flash capacity provides a practical balance between firmware size and embedded cost for control-oriented products.

Typical uses include industrial sensor controllers, motor-control systems, CAN-connected equipment, compact data acquisition units, medical monitoring devices, and low-cost consumer electronics. The two ADCs support analog measurement, while the three DACs allow programmable voltage outputs for excitation, test, or signal-generation functions. CAN connectivity makes the MCU appropriate for distributed control networks requiring standard and extended frames.

Designers should preserve the voltage and decoupling requirements in the manufacturer datasheet, place supporting components close to the power pins, and route analog inputs away from fast-switching signals. Firmware should also verify operating limits, clock configuration, and analog calibration after power-up. The 64-pin footprint simplifies inspection, but analog performance still depends on careful grounding and reference design.

This page organizes the key MCU specifications, sourcing information, available drop-in comparisons, and practical design guidance into a focused engineering reference. It is intended to help designers evaluate the STM32F334R8T7 for mixed-signal embedded systems while keeping package, memory, analog, and communication requirements in view.

Alternatif penggantian untuk STM32F334R8T7 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian STM32F334R8T7 (sama faktor bentuk dan footprint) — berbeda di dalam Flash Memory, Package, SRAM.

STMicroelectronics
Flash Memory: 64 KB
Package: LQFP64 (10x10 mm)
SRAM: 12 KB
Bandingkan dengan STM32F334R8T7 →

STM32F334R8T6

✅ Drop-In
STMicroelectronics
📦 64-LQFP (10x10)
ARM Cortex-M4 with FPU · 72 MHz · 64 KB · 12 KB · LQFP64 (10x10 mm) · 2.0V to 3.6V · -40°C to +85°C · 51

Kontak untuk harga

Lihat Datasheet →

STM32F334R8T7 Rating Maksimal & Karakteristik Listrik

Product Type 32-bit Arm Cortex-M4 microcontroller
Maximum Core Frequency 72 MHz
Flash Memory 64 KB (64K x 8)
SRAM 16 KB
ADC Count 2
DAC Count 3
CAN Maximum Bit Rate 1 Mbit/s
CAN Standard CAN 2.0A and CAN 2.0B
CAN Frame Support 11-bit standard and 29-bit extended identifiers
Processor Core Arm Cortex-M4 with floating-point unit
Paket 64-LQFP, 10 mm x 10 mm
Jumlah Pin 64 pins
Tipe Mounting Surface mount

STM32F334R8T7 64-lqfp, 10 mm x 10 mm Diamant Konfigurasi Panduan

Konfigurasi pin untuk STM32F334R8T7 (64-lqfp, 10 mm x 10 mm pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.

Diamant diagram pakai pakai 64-lqfp, 10 mm x 10 mm untuk STM32F334R8T7

Tidak ada data diatribut pin yang tersedia untuk STM32F334R8T7.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

STM32F334R8T7 cocok untuk 6 aplikasis: Industrial Sensor Controller, CAN-Connected Control Module, Compact Data-Acquisition Unit, Precision Motor-Control Platform, Medical Monitoring Controller, Programmable Test and Signal Generator.

🏭

Industrial Sensor Controller

The STM32F334R8T7 fits industrial sensor controllers that require fast local processing alongside compact analog conversion. Its 72 MHz Arm Cortex-M4 core can execute control logic while two ADCs acquire sensor signals and three DACs provide programmable analog outputs for excitation, testing, or actuator control. The 64 KB Flash and 16 KB SRAM provide dedicated program and working memory without requiring a separate processor. Its 64-LQFP package also exposes the mixed-signal and digital resources needed for a practical industrial controller. Engineers should design the analog front end around the datasheet ADC and DAC characteristics, use a clean reference strategy, and isolate sensitive measurement paths from switching nodes.

🌐

CAN-Connected Control Module

The STM32F334R8T7 is appropriate for distributed CAN control modules because its controller supports CAN 2.0A and 2.0B frames with rates up to 1 Mbit/s. The 72 MHz Cortex-M4 core can handle protocol tasks, diagnostics, and local control, while two ADCs and three DACs add measurement and output capability without requiring separate mixed-signal devices. In an implementation, the MCU connects through a suitable CAN transceiver, and the PCB must provide correct termination and controlled differential routing. Firmware should include bus-off recovery, error counters, frame validation, and timing checks so a communications fault does not compromise the wider equipment.

📟

Compact Data-Acquisition Unit

The STM32F334R8T7 can form the core of a compact data-acquisition unit requiring two analog inputs, three programmable analog outputs, and real-time digital processing. Its 72 MHz Cortex-M4 core and 16 KB SRAM support sampling control, scaling, filtering, and communication tasks, while 64 KB Flash accommodates embedded firmware and configuration data. The three DACs may generate test stimuli or programmable references for a controlled measurement system. To achieve useful results, designers should establish analog grounding, reference stability, input filtering, and calibration sequences directly from the manufacturer datasheet. Firmware should also define overload handling and distinguish valid measurements from out-of-range inputs.

⚡

Precision Motor-Control Platform

The STM32F334R8T7 suits compact motor-control platforms that need fast computation, mixed-signal feedback, and network communication in one component. Its 72 MHz Arm Cortex-M4 core with a floating-point unit supports real-time control calculations, while the two ADCs can monitor analog feedback signals and the three DACs can provide control or test outputs. CAN 2.0A and 2.0B support is useful in coordinated industrial motion systems. The 64-LQFP footprint provides access to a broad pin set while retaining a conventional surface-mount package. Power-stage design, isolation, current sensing, protection, and timing must be evaluated independently, since those external functions determine achievable motor performance and safety.

💊

Medical Monitoring Controller

The STM32F334R8T7 can support compact medical monitoring controllers where sensor acquisition, local signal processing, and a reliable communications path are needed. Two ADCs provide the analog input resources, three DACs support calibration or controlled test outputs, and the 72 MHz Cortex-M4 core handles data conditioning and system tasks. CAN connectivity allows the controller to participate in a wired equipment network, although the final medical product may require additional communication and safety functions. Design work should address analog isolation, low-noise references, calibration, fault detection, and software validation. The MCU's general-purpose status does not itself establish medical-device certification or compliance.

🧪

Programmable Test and Signal Generator

The STM32F334R8T7 is well suited to programmable test equipment and low-bandwidth signal generation because it combines three DACs with a 72 MHz real-time processor. The DAC outputs can create controlled analog test signals, while the Cortex-M4 floating-point unit supports calculation, waveform shaping, and timing routines. Its 64 KB Flash and 16 KB SRAM allow embedded control functions without a separate host processor, and CAN can coordinate commands with larger systems. Practical performance depends on the DAC reference, output buffering, reconstruction filtering, and the analog output bandwidth required by the application. Use the manufacturer characteristic and application information to select those external components.

Ringkasan Produk Direkomendasikan

STM32F334R8T6 STMicroelectronics Digunakan di dalam: Industrial Sensor Controller, CAN-Connected Control Module, Compact Data-Acquisition Unit, Precision Motor-Control Platform, Medical Monitoring Controller, Programmable Test and Signal Generator STM32F334R8T7TR Same-device tape-and-reel order form Digunakan di dalam: Industrial Sensor Controller, CAN-Connected Control Module, Compact Data-Acquisition Unit, Precision Motor-Control Platform, Medical Monitoring Controller, Programmable Test and Signal Generator
What is the STM32F334R8T7?
The STM32F334R8T7 is a 32-bit Arm Cortex-M4 microcontroller rated up to 72 MHz, with 64 KB of Flash, 16 KB of SRAM, two ADCs, three DACs, and 64 pins. It is packaged in a 10 mm by 10 mm LQFP. According to the manufacturer datasheet, the device also includes CAN 2.0A and 2.0B communication and a floating-point processing unit for mixed-signal embedded control.
What are the key specifications of STM32F334R8T7 that engineers should know?
The STM32F334R8T7 combines a 72 MHz Arm Cortex-M4 core, 64 KB of Flash, 16 KB of SRAM, two ADCs, three DACs, and 64-LQFP packaging. Its CAN controller supports standard and extended frames at rates up to 1 Mbit/s. The manufacturer datasheet identifies the processor as having a floating-point unit, making the MCU appropriate for real-time control, measurement, and signal-generation designs.
What is the operating voltage range of STM32F334R8T7?
The STM32F334R8T7 operating-voltage limits must be taken from the DC characteristics and absolute-maximum ratings in the manufacturer datasheet. The device is supplied in a 64-pin LQFP package and also includes two ADCs, three DACs, and a 72 MHz Arm Cortex-M4 core. Use the datasheet limits for supply selection, power sequencing, and protection-component design.
Where can I download the STM32F334R8T7 datasheet PDF?
The STM32F334R8T7 datasheet PDF is available from the official STMicroelectronics document link listed on this page. It describes the STM32F334x4, STM32F334x6, and STM32F334x8 family, including the 72 MHz Cortex-M4 core, 64 KB Flash configuration, 16 KB SRAM, ADC and DAC resources, and CAN controller. The PDF also contains the authoritative pin, electrical, and package information.
Where can I find the STM32F334R8T7 pinout?
The STM32F334R8T7 pinout is found in the pin-description table and package drawings in the manufacturer datasheet. The device uses a 64-LQFP package measuring 10 mm by 10 mm. Use the pin table to map power, ground, reset, clock, debug, communication, analog, and GPIO functions before assigning PCB nets or reviewing a board layout.
Can STM32F334R8T7 control CAN-based industrial equipment?
Yes, the STM32F334R8T7 is suitable for CAN-connected industrial equipment because its controller supports CAN 2.0A and 2.0B frames and rates up to 1 Mbit/s. The 72 MHz Cortex-M4 core provides real-time processing capacity, while two ADCs and three DACs support local measurement and control functions. A practical design still requires correct transceiver selection, termination, routing, and firmware error handling.
Where can I buy STM32F334R8T7 online?
Use the Request a Quote form on this page to request STM32F334R8T7 availability, current lead time, and order handling. The exact device is offered as a 64-LQFP, 72 MHz, 64 KB Flash microcontroller. A written quotation also allows the requested package form, inspection requirements, and production quantities to be confirmed before procurement.
What is the price of STM32F334R8T7?
The current commercial terms for STM32F334R8T7 should be obtained through the Request a Quote form on this page. The request can include required quantity, delivery target, and packaging preferences. This approach provides an updated quotation tied to the exact 64-LQFP device rather than a generic STM32F334 family price.
What is the lead time for STM32F334R8T7?
Request the current lead time for STM32F334R8T7 through the Request a Quote form on this page. Lead time can vary with order quantity, assembly format, production planning, and inventory status, so a project-specific confirmation is preferable to using an unconfirmed interval. State the required quantity and planned delivery date in the request.
Is STM32F334R8T7 in stock?
Use the Request a Quote form on this page to check current STM32F334R8T7 availability and confirm the quantity that can be allocated. The exact orderable identifier is STM32F334R8T7, covering the 64-LQFP, 72 MHz, 64 KB Flash configuration. Availability should be confirmed for the production schedule and required delivery date.
What is the best drop-in replacement for STM32F334R8T7?
STM32F334R8T6 is the closest documented same-package alternative for STM32F334R8T7, but its temperature-grade suffix differs and must be checked against the original device specification. No five-part set of true pin-to-pin cross-brand alternatives was established. Treat any substitution as a design review involving supply limits, timing, peripherals, firmware, qualification, and board-level validation.
What can replace STM32F334R8T7?
STM32F334R8T6 is a candidate replacement because it belongs to the STM32F334R8 family and uses the same 64-pin LQFP format, while the T6 and T7 suffixes indicate different operating-temperature grades. Confirm the complete ordering information, electrical limits, and temperature requirement in the manufacturer datasheet. A footprint match alone does not remove the need for firmware and qualification checks.
STM32F334R8T7 vs STM32F334R8T6 - which is better?
STM32F334R8T7 is the better choice when the design requires the temperature grade denoted by the T7 suffix; STM32F334R8T6 is preferable only when its specified temperature range meets the application. Both belong to the STM32F334R8 family and use a 64-LQFP package with a 72 MHz Cortex-M4 core, 64 KB Flash, and 16 KB SRAM. Verify the grade against the manufacturer datasheet.
When should I choose STM32F334R8T7 over STM32F334R8T6?
Choose STM32F334R8T7 when the operating-temperature requirement calls for the T7 grade and the application can tolerate its specified electrical and environmental limits. The STM32F334R8T6 offers the same family-level processing, memory, analog-resource count, and 64-LQFP footprint, making it a practical comparison candidate. The final selection should follow the exact grade definitions and qualification requirements.
Is STM32F334R8T7 suitable for sensor and data-acquisition systems?
The STM32F334R8T7 is suitable for compact sensor and data-acquisition systems because it combines two ADCs, three DACs, a 72 MHz Cortex-M4 core, and 64 KB of Flash on a 64-LQFP device. The CAN interface can distribute measurements or commands across a network. Achievable measurement accuracy still depends on the selected ADC characteristics, reference design, analog front end, and calibration method.

Data referensi engineering untuk STM32F334R8T7 — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose STM32F334R8T7 when a compact mixed-signal design requires a 72 MHz Cortex-M4 core, 64 KB of Flash, 16 KB of SRAM, two ADCs, three DACs, and CAN connectivity in a 64-LQFP package. STM32F334R8T6 is the closest documented alternative and shares the same family architecture and package, but its T6 temperature grade must satisfy the deployment environment. Other STM32 devices with 64-pin packages should not be assumed to be drop-in replacements because memory organization, peripheral mapping, clock architecture, and pin functions may differ. Before finalizing the device, verify supply limits, temperature range, ADC and DAC characteristics, clock requirements, firmware support, and qualification. For designs exposed to extended-temperature industrial environments, confirm the suffix definition and use the exact ordering information to prevent a grade mismatch during procurement.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini STM32F334R8T6
Brand STMicroelectronics STMicroelectronics
Package 64-LQFP (10x10) 64-LQFP (10x10)
Processor Core Arm Cortex-M4 Arm Cortex-M4
Maximum Core Frequency 72 MHz 72 MHz
Flash Memory 64 KB 64 KB
SRAM 16 KB 16 KB
ADC Count 2 2
DAC Count 3 3
CAN Support CAN 2.0A and CAN 2.0B, up to 1 Mbit/s CAN 2.0A and CAN 2.0B, up to 1 Mbit/s
Temperature-Grade Suffix T7 T6

Diferensiator Kunci

  • Integrated mixed-signal resource set (vsSTM32F334R8T6)
  • Real-time processing with floating-point hardware (vsSTM32F334R8T6)
  • Integrated CAN 2.0A and 2.0B communications (vsSTM32F334R8T6)

Catatan Desain

Decouple each supply group with the capacitance and placement specified in the manufacturer datasheet. Keep the analog and digital grounding strategy consistent with the MCU's reference-design recommendations, and route supply current through low-impedance planes. Verify startup, minimum operating voltage, maximum supply level, and external regulator tolerance before selecting power components; the device's complete electrical limits are not summarized by its 72 MHz clock rating.

Place decoupling capacitors close to their associated power pins and provide a continuous ground reference beneath the LQFP footprint. Route analog inputs away from switching nodes, high-current motor paths, and CAN transceiver return currents. For mixed-signal boards, separate analog and digital return paths where the application permits and use a solid, low-impedance ground structure rather than fragmented planes.

Treat ADC and DAC signals as sensitive analog nets: use short traces, controlled source and load impedances, and shielding where radiated noise matters. Check sampling timing, reference stability, and the acquisition bandwidth implied by the operating clock. The two ADC and three DAC peripherals are useful building blocks, but their practical resolution and settling performance depend on the circuit surrounding the MCU.

Do not substitute a family member solely because its package matches. STM32F334R8T6 shares the 64-LQFP format and major resources, but the T6 and T7 ordering suffixes must be checked against the required temperature range. For CAN networks, also verify transceiver selection, termination, bit timing, error handling, and fault recovery. A successful footprint comparison does not replace complete electrical and firmware validation.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

AEC-Q100 is not applicable to this general-purpose microcontroller ordering code. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product page or current material-compliance documentation.

Data disahkan pada: 2026-11-15 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

STM32F334R8T7 datasheet STM32F334R8T7 datasheet pdf STM32F334R8T7 pinout STM32F334R8T7 LQFP64 pinout STM32F334R8T7 specifications STM32F334R8T7 72MHz Cortex-M4 STM32F334R8T7 ADC DAC STM32F334R8T7 CAN controller STM32F334R8T7 replacement STM32F334R8T7 equivalent STM32F334R8T7 vs STM32F334R8T6 STM32F334R8T7 price STM32F334R8T7 stock STMicroelectronics STM32F334R8T7 STM32F334R8T7 sensor controller

Komponen dan Istilah Terkait

STMicroelectronics STM32F334R8T7 STM32F334R8T6 STM32F334R8T7TR STM32F334R8 STM32F3 Arm Cortex-M4 32-bit microcontroller embedded processor mixed-signal MCU semiconductor 64-LQFP LQFP package family surface-mount package 64 KB Flash 16 KB SRAM floating-point unit ADC DAC CAN 2.0A CAN 2.0B industrial sensor controller motor control data acquisition medical monitoring
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ