THS4222DGN - Dual High-Speed Rail-to-Rail Op Amp | Texas Instruments
Référence : THS4222DGN ✓ ActifTHS4222DGN Présentation
A high-speed operational amplifier is a voltage-feedback amplifier optimized for rapid signal propagation, wide bandwidth, accurate slew behavior, and low output distortion. These characteristics place the device within the broader hierarchy of analog amplifiers, operational amplifier ICs, and power-management-dependent signal-chain components. The THS4222 family is particularly suited to applications requiring high output swing and low distortion while operating from low-voltage single supplies.
The THS4222DGN provides two amplifier channels in one package, reducing board area compared with separate single-channel devices. Its rail-to-rail output stage is intended to maximize usable signal range near the supply rails, while voltage-feedback architecture supports precise closed-loop gain configurations. The 14 mA quiescent-current specification provides a defined baseline for power budgeting when the amplifier operates with its output quiescent and feedback network.
The manufacturer identifies data-converter drive, video switching, and other low-distortion applications as primary use cases. Its 3 V to 15 V operating range supports low-voltage portable systems, industrial interface circuits, instrumentation, video signal conditioning, and communications equipment. Two channels can be used for differential signal conditioning, dual-ended filtering, active balancing, or independent analog paths when board space is constrained.
A key implementation consideration is supply decoupling. High-frequency operation requires short, low-inductance connections from the power pins to ground-plane bypass capacitance. Feedback components should also be placed close to the relevant input and output pins to minimize parasitic inductance and preserve the intended high-speed response. Input and output signal paths should be kept short and away from sources of switching noise.
For design decisions involving the THS4222DGN, engineers should compare bandwidth, slew rate, output-current capability, noise, distortion, and operating-range details against application requirements. This page combines the manufacturer ordering information, package details, functional positioning, sourcing workflow, and verified replacement information to support faster component selection and PCB planning.
Alternatives de remplacement direct pour THS4222DGN — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
THS4222DGNR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
THS4042IDGN
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
THS4041CDGNR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
THS4222DGN Valeurs maximales et caractéristiques électriques
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 3 V to 15 V |
| Courant de repos | 14 mA |
| Type de sortie | Rail-to-rail output |
| Low-Distortion Architecture | High-output-swing, low-distortion |
| Package Type | HVSSOP-8 (DGN) |
| Nombre de broches | 8 pins |
| Plage de température de fonctionnement | -40 °C to +85 °C |
| Type de montage | Surface mount |
Guide de configuration des broches du THS4222DGN hvssop-8 (dgn)
Configuration des broches du THS4222DGN (boîtier hvssop-8 (dgn)). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour THS4222DGN.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
THS4222DGN convient pour 6 applications: Data-Converter Drive, Video Signal Switching, Low-Voltage Instrumentation, Communications Signal Conditioning, Precision Filter and Active Balance, Portable and Embedded Analog Front End.
Data-Converter Drive
The THS4222DGN fits high-speed data-converter input stages because Texas Instruments identifies the THS4222 family for low-distortion converter drive. Its two amplifier channels can provide single-ended drive, differential excitation, or complementary signal paths while operating from a 3 V to 15 V supply. The rail-to-rail output stage offers more usable range than a conventional amplifier whose output is restricted by a fixed saturation boundary. Engineering validation should compare converter input bandwidth, settling behavior, output swing, capacitive loading, and the THS4222 distortion characteristics over the required signal range.
Recommandé
Video Signal Switching
The THS4222DGN is suitable for video-switching buffers because the family combines high output swing, rail-to-rail output operation, and low distortion in a dual-channel 8-pin HVSSOP package. The two channels can support active routing, gain adjustment, impedance conversion, or buffering around a video switch. Its single-supply range of 3 V to 15 V accommodates multiple portable and embedded video architectures. The design should still verify video bandwidth, output-current capability, channel-to-channel behavior, settling time, and distortion at the actual line amplitude and load.
Recommandé
Low-Voltage Instrumentation
The dual THS4222DGN can be used in low-voltage instrumentation where compactness, rail-to-rail output, and low distortion are important. Common roles include sensor conditioning, gain-stage implementation, active filtering, and buffered measurement outputs. The 14 mA quiescent-current figure provides a defined starting point for a portable power budget, while the 3 V minimum supply supports battery-powered instrumentation. Before finalizing the gain network, engineers should confirm small-signal bandwidth, offset and bias behavior, noise performance, common-mode range, and output drive against the sensor source impedance.
Recommandé
Communications Signal Conditioning
The THS4222DGN is applicable to communications signal-conditioning paths that require a high-speed voltage-feedback amplifier and ample output swing. Its dual-channel configuration can process two related signals or implement differential circuitry with fewer packages than discrete single amplifiers. Operating from one 3 V to 15 V rail simplifies compatibility with mixed-signal systems, although the amplifier remains dependent on clean power and careful layout. Check the device's complete bandwidth, slew rate, distortion, output-current capability, and noise specifications against modulation bandwidth, adjacent-channel rejection, and required signal amplitude.
Recommandé
Precision Filter and Active Balance
The two channels of the THS4222DGN can implement active filtering, impedance buffering, line-driver functions, or active balancing when the application requires low distortion and rail-to-rail output. Voltage feedback provides a conventional topology for precise resistor-defined gains and frequency responses. The DGN package helps preserve board density, while the 14 mA quiescent current supports moderate-power portable systems. Component selection should account for resistor tolerance, gain error, noise gain, output loading, and the stability behavior of the selected feedback network across the intended frequency range.
Recommandé
Portable and Embedded Analog Front End
The THS4222DGN supports low-voltage embedded analog front ends where two high-speed channels are useful but a larger multi-amplifier package is undesirable. Its 3 V single-supply operation and 14 mA quiescent current suit battery-powered measurement, control, and communication modules. The rail-to-rail output improves utilization of the available signal range, while the 8-pin HVSSOP package supports compact layouts. Validate the full signal chain at the lowest expected supply voltage because the usable swing and performance limits can vary with supply voltage, load current, output frequency, and temperature.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour THS4222DGN — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | THS4222DGNR | THS4042IDGN | THS4041CDGNR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | HVSSOP-8 (DGN) | HVSSOP-8 (DGN) | HVSSOP-8 (DGN) | HVSSOP-8 (DGN) |
| Primary Application | Data-converter drive, video switching, and low-distortion signal conditioning | Data-converter drive, video switching, and low-distortion signal conditioning | High-frequency precision circuit design | High-frequency amplifier applications |
Principaux différenciateurs
- Dedicated low-distortion family positioning (vs THS4042IDGN)
- Direct assembly-format reuse (vs THS4222DGNR)
- Low-voltage dual-channel integration (vs THS4041CDGNR)
Notes de conception
Place the power-supply bypass capacitor immediately adjacent to the amplifier supply and ground pins, with a short, low-inductance connection to the ground plane. High-speed feedback resistors and compensation components should also be close to the relevant input and output pins. Avoid routing high-speed output traces beneath the package or between input and feedback nodes, because parasitic inductance can create ringing, overshoot, or instability.
Do not assume rail-to-rail output means the output can reach either supply rail at every frequency, load, or temperature. Check the manufacturer output-swing and output-current graphs for the actual load and signal amplitude. Likewise, verify the complete electrical characteristics for the selected THS4222 family member before relying on a proposed substitute, especially bandwidth, slew rate, distortion, and stability with the selected feedback network.
Begin the power budget with the specified 14 mA quiescent current for the dual THS4222 family, then add expected load current and the current associated with the feedback and output stages. For a single 3 V to 15 V supply design, verify that the amplifier can produce the required signal swing at the minimum available voltage. Keep local decoupling current loops small so switching-supply ripple does not propagate directly into the analog output node.
Informations de conformité
No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was identified for the exact MPN. The family is a commercial amplifier IC, so AEC-Q100 is recorded as not applicable.