THS7530PWP - 300 MHz Fully Differential VGA | Texas Instruments
Référence : THS7530PWP ✓ ActifTHS7530PWP Présentation
A variable gain amplifier, or VGA, is an amplifier whose gain changes under electronic control. A VGA belongs to the broader family of amplifiers, which in turn forms part of the analog and mixed-signal semiconductor hierarchy. Unlike a fixed-gain amplifier, a VGA allows a receiver, imaging system, or instrumentation channel to vary signal amplitude without changing the surrounding circuit topology. The fully differential architecture preserves a balanced signal path and reduces sensitivity to common-mode disturbances.
Key features include a 300 MHz small-signal bandwidth, voltage-controlled continuous gain adjustment, differential input and differential output operation, and separate control of output common mode. The device operates from a single 5.5 V supply or from split supplies of ±2.75 V. Its 14-pin HTSSOP package exposes a thermal pad for improved heat dissipation, and the specified operating temperature range is -40 °C to 85 °C.
Internally, the THS7530 uses Texas Instruments' BiCom III silicon-germanium complementary bipolar process. That process supports the high-speed operation required by the device while preserving DC coupling and low-impedance differential outputs. The gain-control and common-mode inputs are high-bandwidth control paths, so their routing and impedance matter as much as the signal inputs when system settling time is important.
Typical uses include ultrasound and medical imaging front ends, communications receivers, instrumentation amplifiers, oscilloscope and test-equipment input chains, and other wideband analog systems that require adjustable attenuation or gain. Differential signaling is particularly useful when the source produces a small differential voltage across a common-mode range that a single-ended amplifier would not accommodate cleanly.
For PCB design, use the exposed thermal pad as a heat-spreading and low-inductance connection rather than leaving it electrically unconnected. Place input, output, gain-control, and common-mode routing away from high-current switching nodes. Terminate differential pairs symmetrically and follow the pin-description table in the manufacturer datasheet when assigning tracks and ground connections.
This page combines the manufacturer device information, orderable-package details, practical PCB guidance, and a constrained drop-in comparison for engineers who need a 300 MHz fully differential VGA in the HTSSOP PWP footprint. Use the Request a Quote form on this page for current commercial availability, minimum order quantity, and lead-time confirmation.
Alternatives de remplacement direct pour THS7530PWP — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
THS7530QPWPRQ1
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
THS7530PWPRG4
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
THS7530PWPG4
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
THS7530PWP Valeurs maximales et caractéristiques électriques
| Device Type | Fully differential, continuously variable gain amplifier |
| Amplifier Configuration | 1 circuit, differential input and differential output |
| Small-Signal Bandwidth | 300 MHz |
| Gain Control | Continuous, voltage controlled |
| Signal Coupling | DC-coupled |
| Single-Supply Range | 5.5 V |
| Split-Supply Range | ±2.75 V |
| Input Impedance | High impedance, differential |
| Output Impedance | Low impedance, differential |
| Output Common-Mode Control | Yes |
| Output Voltage Clamp | Yes |
| Process Technology | BiCom III SiGe complementary bipolar |
| Plage de température de fonctionnement | -40 °C to 85 °C |
| Boîtier | 14-pin HTSSOP (PWP) with exposed pad |
| Type de montage | Surface mount |
| Courant d'alimentation | 37 mA |
| Statut RoHS | RoHS compliant |
Guide de configuration des broches du THS7530PWP 14-pin htssop (pwp) with exposed pad
Configuration des broches du THS7530PWP (boîtier 14-pin htssop (pwp) with exposed pad). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour THS7530PWP.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
THS7530PWP convient pour 6 applications: Medical and Ultrasound Imaging Front Ends, Communications Receiver Signal Conditioning, Precision Instrumentation and Measurement, Oscilloscope and Test Equipment Input, Optical and Sensor Interface Amplification, Automotive Vision and Radar Electronics.
Medical and Ultrasound Imaging Front Ends
The THS7530PWP fits high-speed imaging channels where signal amplitude varies across the scanned field and must be normalized without swapping external attenuators. Its 300 MHz bandwidth preserves the temporal detail needed by ultrasonic and medical imaging systems, while the continuously variable gain control allows a controller to adjust amplitude in real time. The fully differential input and output architecture supports balanced source and downstream converter connections. A practical trade-off is that a wideband VGA is not the lowest-power choice: the device draws 37 mA and dissipates heat through its exposed pad, so the PCB must provide a thermal path and the system must control signal swing to avoid unnecessary dissipation.
Recommandé
Communications Receiver Signal Conditioning
The THS7530PWP is applicable to wideband receiver chains that require continuous gain adjustment close to the antenna or sensor interface. Its 300 MHz bandwidth accommodates high-rate intermediate-frequency or baseband signals, and the differential signal path helps reject common-mode noise picked up between the source and amplifier. Voltage-controlled gain also supports automatic gain control, distance compensation, or calibration loops. The system designer must verify the gain-control bandwidth against the required loop settling time and keep the control trace short, because a long control route can degrade adjustment speed even when the main signal bandwidth is adequate.
Recommandé
Precision Instrumentation and Measurement
The THS7530PWP supports instrumentation channels that compare small sensor outputs against a large common-mode range and need programmable attenuation before conversion or comparison. Its DC-coupled differential input preserves low-frequency information that an AC-coupled amplifier would lose, while the 300 MHz bandwidth leaves margin for fast transients and test fixtures. The low-impedance differential output can drive downstream circuitry through controlled routing, and the common-mode control adds flexibility in system-level signaling. Designers should confirm the gain-control input range and settling behavior against the required measurement sequence, because continuous gain does not imply instantaneous correction.
Recommandé
Oscilloscope and Test Equipment Input
The THS7530PWP can serve as an adjustable front-end element in oscilloscopes, signal analyzers, and automated test systems that must handle inputs spanning widely different amplitudes. The 300 MHz bandwidth supports high-speed edge capture, while continuous gain control allows a single analog path to replace multiple switched attenuator positions. Differential routing preserves signal integrity when the source is balanced, and the exposed-pad HTSSOP package provides a practical thermal path in compact instrumentation. Validation should include gain accuracy, control settling, output clamping, and thermal rise under the highest expected input condition; these details determine whether calibration can correct amplitude without excessive correction bandwidth.
Recommandé
Optical and Sensor Interface Amplification
The THS7530PWP is suitable for sensor-interface amplifiers where a weak differential signal is followed by a larger processing stage and gain must track source amplitude or calibration conditions. Its 300 MHz bandwidth allows the same amplifier to handle sensor signals with meaningful edge content, while DC coupling preserves slow baseline information. The fully differential topology is advantageous when the sensor and cable introduce common-mode noise. To obtain predictable performance, use balanced source impedances, short input traces, and a symmetric output arrangement. Also verify that the gain-control range covers the attenuation required without pushing the amplifier into saturation or an unstable operating region.
Recommandé
Automotive Vision and Radar Electronics
The automotive-qualified THS7530QPWPRQ1 ordering variant is the relevant option for automotive electronics, while the standard THS7530PWP serves industrial and commercial versions of the same high-speed VGA function. Both use the 14-pin HTSSOP PWP footprint and support a 300 MHz differential signal path, making the architecture relevant to camera, radar, and high-speed interface conditioning where adjustable gain helps normalize changing signal levels. Automotive designs require careful review of qualification documentation, temperature expectations, transient conditions, and supply sourcing. The exposed pad remains thermally important because the 37 mA supply current and output-drive dissipation both contribute to junction heating.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour THS7530PWP — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | THS7530QPWPRQ1 | THS7530PWPRG4 | THS7530PWPG4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | HTSSOP-14 (PWP) with exposed pad | HTSSOP-14 (PWP) with exposed pad | HTSSOP-14 (PWP) with exposed pad | HTSSOP-14 (PWP) with exposed pad |
| Device Function | Fully differential, continuously variable gain amplifier | Fully differential, continuously variable gain amplifier | Fully differential, continuously variable gain amplifier | Fully differential, continuously variable gain amplifier |
| Bandwidth | 300 MHz | 300 MHz | 300 MHz | 300 MHz |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Supply Voltage | 5.5 V single or ±2.75 V split supply | 5.5 V single or ±2.75 V split supply | 5.5 V single or ±2.75 V split supply | 5.5 V single or ±2.75 V split supply |
| Automotive Qualification | Not indicated | Automotive-qualified Q1 ordering option | Not indicated | Not indicated |
| Signal Coupling | DC-coupled | DC-coupled | DC-coupled | DC-coupled |
| Output Common-Mode Control | Yes | Yes | Yes | Yes |
Principaux différenciateurs
- Continuously adjustable gain in a fully differential high-speed amplifier (vs THS7530QPWPRQ1)
- Wideband gain and common-mode control within one device (vs THS7530PWPRG4)
- Single-supply and split-supply operation (vs THS7530PWPG4)
Notes de conception
Follow the PWP land pattern in the manufacturer datasheet and connect the exposed pad with multiple thermal vias to a solid plane. Treat the pad as an electrical and thermal feature, not as unused package area. Keep input, output, gain-control, and common-mode routes short, and avoid routing them beside switching-node or high-current return paths. Symmetrical routing is especially important for the differential input and output pairs because unmatched geometry can degrade common-mode rejection and disturb gain or phase performance.
Give the gain-control and output common-mode inputs dedicated, low-impedance routing. These are wideband control paths, so excessive trace resistance, capacitance, or nearby high-current switching edges can slow control settling and introduce coupling into the signal channel. Use a compact control network and provide a quiet return beneath the device. If the control source is remote, buffer it close to the amplifier rather than extending a long analog control trace across the board.
Estimated: using the stated 37 mA supply current at 5.5 V, supply power is approximately 0.204 W before output-load dissipation. Junction temperature will additionally rise with output drive and signal swing, so calculate the complete worst-case dissipation rather than using supply power alone. Verify the result against the manufacturer thermal information and the actual PCB copper area. Increase exposed-pad copper and via count if the estimated junction temperature approaches the device limit.
Do not treat the 300 MHz small-signal bandwidth as permission to route the differential signal with arbitrary long traces or large impedance discontinuities. Terminate the source and destination impedances consistently, maintain symmetric spacing between differential pairs, and place return vias alongside signal vias where the stackup permits. Also confirm that the gain-control voltage remains inside its operating region during startup and power-sequencing transients; otherwise the amplifier may settle incorrectly or enter an unintended operating condition.
Informations de conformité
RoHS-compliant ordering variants are identified for the THS7530 family. The standard THS7530PWP is not identified as an automotive-qualified ordering code; use THS7530QPWPRQ1 when automotive qualification is required. REACH, halogen-free, lead-free, and conflict-minerals declarations are not established by the available product information.