TJA1021T/10/C - 10.4 kBd LIN Transceiver | NXP | SO-8
Référence : TJA1021T/10/C ✗ Fin de vieTJA1021T/10/C Présentation
A LIN transceiver, also called a LIN physical-layer interface, converts logic-level signals from a LIN controller into the dominant and recessive states used on the physical bus. It also receives bus levels and presents compatible logic signals to the controller. Within the hierarchy of interface ICs, the TJA1021 belongs to the automotive LIN transceiver class and supports low-speed serial networking commonly used for distributed vehicle body and comfort systems.
The TJA1021T/10/C is specifically optimized for the 10.4 kBd maximum transmission speed specified by SAE J2602. NXP identifies the device as compatible with the TJA1020 and MC33662 (B), which supports reuse of established LIN hardware platforms. Its LIN 2.x protocol coverage and standardized bus interface allow it to be used alongside common automotive LIN controllers, while the 8-pin SO package keeps the physical implementation compact.
NXP describes the TJA1021 family as operating from 1 kBd to 20 kBd and supporting LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016. The /10 derivative emphasizes 10.4 kBd performance, while /20 derivatives emphasize the maximum 20 kBd rate. This distinction is important when the physical bus topology, transceiver selection or protocol-controller timing was designed around a particular LIN operating speed.
Typical applications include automotive LIN master and slave nodes, door and seat modules, climate-control controllers, lighting modules, sensor gateways and body-control subsystems. The same physical interface can also support industrial LIN-compatible equipment where a standardized low-speed serial bus is used instead of a more complex CAN or Ethernet network.
When laying out a replacement board, confirm the exact pin functions and exposed-pad requirements against the NXP manufacturer datasheet. Pay particular attention to bus termination, ground connection, supply decoupling and the controller-side logic levels; changing a LIN transceiver package variant without checking these details can create interoperability or EMC problems even when the connector appears identical.
This product page combines protocol compatibility, package information, lifecycle status, verified source links and engineering-oriented selection guidance. It also identifies pin-compatible NXP family alternatives and explains when their optimized LIN baud rate or device generation changes the replacement decision.
Alternatives de remplacement direct pour TJA1021T/10/C — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec TJA1021T/10/C (même facteur de forme et même empreinte) — différant par Package, Product Type.
TJA1020T/N1,118
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MC33662B
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TJA1021AT/10
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TJA1021T/20/C
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →TJA1021BT/20
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TJA1021T/10/C Spécifications
| Product Type | LIN bus transceiver |
| Transceiver Configuration | Half LINbus |
| Boîtier | 8-pin SO |
| Type de montage | Surface mount |
| Optimized LIN Transmission Speed | 10.4 kBd |
| Family Supported Baud Rate Range | 1 kBd to 20 kBd |
| LIN 2.0 Support | Supported |
| LIN 2.1 Support | Supported |
| LIN 2.2 Support | Supported |
| LIN 2.2A Support | Supported |
| SAE J2602 Support | Supported |
| ISO 17987-4:2016 Support | Supported |
| Pin Compatibility | Compatible with TJA1020 and MC33662 (B) |
| Integrated Functions | LIN bus driver and receiver |
Guide de configuration des broches du TJA1021T/10/C 8-pin so
Configuration des broches du TJA1021T/10/C (boîtier 8-pin so). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour TJA1021T/10/C.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
TJA1021T/10/C convient pour 6 applications: Automotive LIN Master Node, Vehicle Body Control Module, Door and Seat Control Module, Automotive Lighting Controller, Industrial LIN Sensor Gateway, Climate Control Node.
Automotive LIN Master Node
The TJA1021T/10/C fits an automotive LIN master node where the host controller must communicate with slave modules over the physical LIN bus. Its 10.4 kBd optimization aligns with the SAE J2602 operating point, while support for LIN 2.0, LIN 2.1, LIN 2.2 and LIN 2.2A provides compatibility with common automotive control architectures. The integrated driver and receiver reduce the external interface circuitry required between the controller and bus. Because the device is End of Life, a replacement review should confirm supply continuity, protocol timing and the exact 8-pin SO footprint before committing a new production design.
Recommandé
Vehicle Body Control Module
A body-control module can use the TJA1021T/10/C to connect a local microcontroller to LIN-attached door, mirror, lighting or climate-control modules. The 10.4 kBd-optimized interface suits established SAE J2602 network segments, while the eight-pin SO package supports compact board layouts. Its documented support for LIN 2.2A and ISO 17987-4:2016 can be valuable when the host controller and attached nodes implement newer LIN behavior. Design reviews should verify the bus termination strategy, ground reference and controller-side signal levels against the NXP datasheet, particularly for an End of Life production continuation.
Recommandé
Door and Seat Control Module
The TJA1021T/10/C is appropriate for distributed door or seat-control nodes that exchange commands and sensor status with a vehicle master through a LIN bus. The half LIN-bus configuration integrates the physical driver and receiver while the 10.4 kBd suffix targets a conservative SAE J2602 operating rate suitable for low-bandwidth body systems. Using a standard SO-8 footprint also simplifies mechanical integration beside the node microcontroller. Before release, validate wake-up, sleep and standby behavior, bus overvoltage tolerance and operating temperature because those electrical details must be taken directly from the manufacturer datasheet.
Recommandé
Automotive Lighting Controller
A LIN-connected lighting controller can employ the TJA1021T/10/C as the physical interface between its controller and the vehicle LIN network. The device's 10.4 kBd optimization and support for six named LIN and related protocol versions provide a standardized basis for command exchange with distributed lighting nodes. Integration in an 8-pin SO package limits board-area impact in compact electronic control units. Engineers should confirm that the module's LIN controller timing, supply range and fault-recovery requirements match the selected transceiver, and should plan early for EOL availability or a qualified pin-compatible replacement.
Recommandé
Industrial LIN Sensor Gateway
The TJA1021T/10/C can bridge a microcontroller or embedded controller to a LIN-compatible sensor network in industrial equipment. Although LIN is most strongly associated with automotive body systems, its single-wire bus and standardized physical layer are also suitable for low-cost distributed controls. The transceiver operates in a half-bus arrangement, supports LIN 2.x protocol versions and is optimized for 10.4 kBd communication. The SO-8 package simplifies assembly into compact gateways. Verify the industrial environment's temperature range, EMC requirements and bus topology because those specifications are not established by the family-level product description alone.
Recommandé
Climate Control Node
A climate-control node can use the TJA1021T/10/C to connect temperature, fan or actuator controllers over a LIN subnetwork. The 10.4 kBd operating point is appropriate for low-bandwidth control traffic and provides a defined match to the SAE J2602 specification cited by NXP. Protocol support across LIN 2.0 through LIN 2.2A improves the chance of compatibility with established vehicle controllers, while the eight-pin SO package keeps the interface compact. During schematic review, confirm logic thresholds, supply decoupling and pin assignments in the NXP datasheet, then review an approved substitute if the End of Life status affects procurement continuity.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TJA1021T/10/C — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TJA1020T/N1,118 | MC33662B | TJA1021AT/10 | TJA1021T/20/C | TJA1021BT/20 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SO-8 | SO-8 | SO-8 | SO-8 | SO-8 | SO-8 |
| Documented Pin Compatibility | TJA1021 family reference | Pin-compatible with TJA1021 | MC33662 (B) pin-compatible with TJA1021 | Same TJA1021 family | Same TJA1021 family | Pin-to-pin and hardware/software compatible with TJA1021T/20 |
Principaux différenciateurs
- Application-specific 10.4 kBd optimization (vs TJA1021T/20/C)
- Broader documented protocol coverage (vs MC33662B)
- Established pin compatibility within the NXP portfolio (vs TJA1020T/N1,118)
Notes de conception
Assign the PCB footprint and every net by comparing the exact ordering code with the pin-description and package drawings in the NXP manufacturer datasheet. The listing confirms an 8-pin SO package, but a mechanically similar package does not guarantee identical lead numbering or exposed-pad requirements. Place the transceiver close to the LIN connector and controller, maintain a continuous ground reference and route the bus away from switching nodes and sensitive analog traces.
Do not treat the /10 and /20 suffixes as packaging variants. TJA1021T/10/C is optimized for 10.4 kBd, while the TJA1021T/20/C is optimized for 20 kBd. Although both support the broader 1 kBd to 20 kBd family range, the optimized device choice should match the controller timing and bus design. Also verify that a selected substitute has the same pin arrangement rather than relying only on an SO-8 package designation.
Preserve the LIN bus topology and termination arrangement recommended for the controller and transceiver. Keep the LIN connection away from clocks, power inductors and high-current switching paths, and provide a low-impedance ground return beneath the transceiver and its decoupling network. EMC performance depends on the complete node implementation, so validate the assembled module against the applicable automotive or industrial requirements rather than judging the transceiver in isolation.
Follow the NXP recommended supply-decoupling arrangement and keep the input capacitor connection short between the device pins and ground. Confirm the production design's supply range, sleep current and transceiver state transitions against the datasheet before changing components. For an End of Life replacement, compare these electrical characteristics as well as the pinout; a mechanically identical substitute can still alter system power budget or controller timing.
Informations de conformité
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free or conflict-minerals statement was identified in the source results. Automotive protocol standards shown for this device must not be interpreted as AEC-Q100 qualification.