TJA1021TK/10/C - LIN Transceiver | NXP Semiconductors
Référence : TJA1021TK/10/C ✗ Fin de vieTJA1021TK/10/C Présentation
A LIN transceiver is the physical-layer component of a Local Interconnect Network. The protocol controller generates the logical command and receive data, while the transceiver converts TXD logic into a shaped LIN bus signal and converts the bus voltage into RXD for the controller. The TJA1021 therefore belongs to the hierarchy of LIN transceiver, vehicle network interface IC, automotive interface IC, and semiconductor.
The TJA1021 uses optimized slew-rate control and wave shaping to minimize electromagnetic emissions. It is pin-to-pin compatible with the TJA1020 and MC33662(B), according to the NXP manufacturer datasheet, and supports in-vehicle subnet architectures operating from 1 kBd through 20 kBd. These characteristics make it applicable to body electronics, comfort systems, lighting, door modules, seat controls, and other low-speed vehicle networks.
The 8-pin HVSON construction supports compact PCB placement while providing the package area and pin arrangement expected for automotive network interfaces. The device provides separate communication-side and logic-side functions, allowing the protocol controller to remain isolated from the physical bus interface. Its bus-level shaping is important in distributed vehicle electrical systems where a rapidly switching signal could interfere with adjacent harnesses and electronic control units.
The TJA1021 is appropriate for LIN master nodes, LIN slave nodes, body-control modules, climate-control electronics, lighting controllers, and sensor gateways. It can also support LIN-compatible industrial or transportation networks when the system design explicitly implements the LIN physical-layer specification. The manufacturer identifies the TJA1021TK family as end of life, so engineers should review availability and lifecycle requirements before starting a new design.
For PCB implementation, follow the pin-description table and exposed-pad guidance in the manufacturer datasheet. Keep the LIN and supply connections compact, provide the required bus and supply decoupling, and review termination, pull-up, routing, and grounding against the final vehicle-network topology. Do not substitute a generic transceiver solely from its bus description; confirm package pinout, logic levels, sleep behavior, and automotive qualification.
This page consolidates the device identity, LIN standards, operating-rate range, lifecycle information, package characteristics, verified drop-in relationship, and practical implementation considerations into one engineering reference. The most important sourcing action is to confirm the exact suffix, package variant, qualification level, and lifecycle plan before committing a production BOM.
Alternatives de remplacement direct pour TJA1021TK/10/C — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
TJA1021TK/10/C/S90
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TJA1021TK/10/C Spécifications
| Product Type | LIN physical-layer transceiver |
| LIN Data Rate | 1 kBd to 20 kBd |
| Supported LIN Versions | LIN 2.0, LIN 2.1, LIN 2.2 and LIN 2.2A |
| Automotive Network Standard | SAE J2602 |
| International Standard | ISO 17987-4:2016 |
| Transceiver Mode | LIN master or slave |
| Boîtier | 8-pin HVSON, 3 x 3 mm |
| Terminal Count | 8 terminals |
| Type de montage | Surface mount |
| Statut du cycle de vie | End of life |
Guide de configuration des broches du TJA1021TK/10/C 8-pin hvson, 3 x 3 mm
Configuration des broches du TJA1021TK/10/C (boîtier 8-pin hvson, 3 x 3 mm). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour TJA1021TK/10/C.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
TJA1021TK/10/C convient pour 6 applications: Vehicle Body-Control Module, Automotive Lighting Controller, Door and Seat Control Module, Climate-Control Electronics, Industrial LIN Sensor Gateway, Automotive Accessory Module.
Vehicle Body-Control Module
The TJA1021TK/10/C fits a LIN body-control module that connects switches, lamps, and latch actuators to a central controller. Its 1 kBd to 20 kBd operating range matches the low-speed subnet defined by LIN 2.0 through LIN 2.2A, while optimized slew rate and wave shaping help reduce electromagnetic emission from the wiring harness. The device separates the controller's TXD and RXD interface from the physical bus. Implement the documented 8-pin HVSON land pattern, including its exposed-pad connection, and verify the bus pull-up and termination arrangement in the final harness topology.
Recommandé
Automotive Lighting Controller
A distributed lighting controller can use the TJA1021TK/10/C to communicate over a LIN subnet without placing a full vehicle network stack at the remote lamp module. The NXP manufacturer datasheet identifies in-vehicle subnetworks as the intended environment and specifies operation from 1 kBd to 20 kBd. Optimized bus wave shaping is particularly useful where the harness is long or runs near other vehicle electrical systems. Validate the module's wake-up, sleep, and supply behavior against the exact datasheet, and preserve the recommended supply and bus-component placement to avoid adding avoidable emissions or susceptibility problems.
Recommandé
Door and Seat Control Module
The TJA1021TK/10/C is suitable for door-lock, window, seat-position, and switch-control modules that use LIN as a cost-efficient local communication link. Its 1 kBd to 20 kBd range accommodates the low-bandwidth command traffic typical of these subsystems, while the 3 x 3 mm HVSON package supports compact controller boards. The LIN controller retains protocol and diagnostic processing, and the TJA1021 handles the physical bus conversion. Use the exact manufacturer pin-description table, connect the exposed pad as specified, and confirm EMC performance with the production wiring harness and enclosure configuration.
Recommandé
Climate-Control Electronics
The TJA1021TK/10/C can connect climate-control buttons, panel actuators, and sensor nodes through a LIN subnet. The device supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016, allowing it to participate in standardized vehicle-network communication from 1 kBd to 20 kBd. Its slew-rate-controlled output is intended to minimize electromagnetic emission in an electronics-dense passenger compartment. Confirm the module's operating-voltage range, sleep thresholds, and wake-up behavior in the NXP manufacturer datasheet, and test EMC behavior with the final cable length, bus capacitance, and termination network.
Recommandé
Industrial LIN Sensor Gateway
The TJA1021TK/10/C can support a LIN sensor gateway when the equipment intentionally implements the LIN physical-layer specification. Its 1 kBd to 20 kBd range is appropriate for simple master-to-slave command and response networks, and the 3 x 3 mm HVSON package allows a compact interface section on a mixed-signal board. The physical layer converts controller TXD commands into shaped bus signals and returns bus status through RXD. Because the product is identified as end of life, confirm procurement continuity and use the TJA1021TK/10/C/S90 option when automotive qualification or an alternate lifecycle path is required.
Recommandé
Automotive Accessory Module
The TJA1021TK/10/C fits an accessory node that communicates commands over a LIN subnet, such as a seat accessory, HVAC actuator, or local switch interface. Its standardized support for LIN 2.x, SAE J2602, and ISO 17987-4:2016 provides a clear protocol basis for interoperability. The 20 kBd maximum rate supports the intended low-speed command class while reducing bus activity compared with faster network interfaces. Review the exact ordering suffix, supply limits, exposed-pad layout, and low-power requirements in the manufacturer datasheet. For new automotive production, compare the base part with the AEC-Q100-qualified S90 variant and validate end-of-life supply before design freeze.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TJA1021TK/10/C — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TJA1021TK/10/C/S90 |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 8-pin HVSON, 3 x 3 mm | 8-pin HVSON, 3 x 3 mm |
| Function | LIN master/slave physical-layer transceiver | LIN master/slave physical-layer transceiver |
| LIN Data Rate | 1 kBd to 20 kBd | 1 kBd to 20 kBd |
| Supported LIN Versions | LIN 2.0, 2.1, 2.2 and 2.2A | LIN 2.0, 2.1, 2.2 and 2.2A |
| Automotive Standards | SAE J2602 and ISO 17987-4:2016 | SAE J2602 and ISO 17987-4:2016 |
| Core Interface Parameter Difference | Reference | 0% difference for cited core interface |
Principaux différenciateurs
- Documented compatibility with established NXP LIN families (vs TJA1020)
- Automotive qualification option in the same interface family (vs TJA1021TK/10/C/S90)
- Compatibility with the MC33662(B) LIN interface family (vs MC33662(B))
Notes de conception
Implement the 8-pin HVSON footprint exactly as shown in the NXP manufacturer datasheet, including the exposed-pad connection and its recommended layout. Keep the TXD, RXD, supply, ground, and LIN connections short, and place the specified local decoupling directly at the relevant device pins. Do not substitute a generic SOIC-8 land pattern merely because both packages contain eight terminals.
Route the LIN bus away from sensitive analog and high-speed digital traces, and keep the bus-side return path continuous to reduce radiated emissions and susceptibility. Apply the bus pull-up and termination components specified for the complete network topology. Because the TJA1021 uses optimized slew rate and wave shaping, maintaining the documented component placement and trace geometry preserves the intended EMC behavior.
Check the exact ordering suffix before releasing the PCB or placing a purchase order. TJA1021TK, TJA1021T, TJA1021TK/10/C, and TJA1021TK/10/C/S90 are not automatically interchangeable solely because they share the TJA1021 name. Confirm package, qualification, temperature range, and lifecycle status, then compare the electrical limits and pin descriptions for the exact device being installed.
Informations de conformité
AEC-Q100 is identified for the related TJA1021TK/10/C/S90 ordering code. Compliance status for the base TJA1021TK/10/C should be confirmed through the exact manufacturer product documentation.