TJA1027TK/20/1 - LIN 2.2A Transceiver | NXP
Référence : TJA1027TK/20/1 ✓ ActifTJA1027TK/20/1 Présentation
A Local Interconnect Network transceiver is the physical-layer interface between a LIN protocol controller and the vehicle's LIN wiring. It combines the bus transmitter, receiver, voltage-domain conversion, and protection functions required to connect a microcontroller-based master or slave node to a low-cost, single-wire automotive network. LIN belongs to the broader hierarchy of automotive interface ICs, communication transceivers, interface ICs, and semiconductors.
Key characteristics include operation at up to 20 kBd, compatibility with LIN 2.0 through LIN 2.2A, and compliance with SAE J2602 and ISO 17987-4:2016 for 12 V systems. The TJA1027 is pin-compatible with the TJA1020 and TJA1021 families, making it useful when a design must consolidate LIN transceiver sourcing while retaining the established physical footprint and board-level implementation.
The TJA1027 integrates the LIN physical-layer transmitter and receiver with logic-side supply support, allowing a protocol controller to communicate through the vehicle LIN bus. Its compliance targets cover both LIN 2.2A and SAE J2602 requirements, providing a defined basis for automotive sub-network designs. Exact operating limits, electrical thresholds, bus-loading limits, and transceiver timing should be checked against the manufacturer datasheet for the selected ordering code.
Typical uses include LIN master nodes, LIN slave nodes, body-control modules, seat and door modules, climate-control peripherals, switch interfaces, sensors, and lighting modules. The device is particularly relevant to 12 V vehicle architectures operating below the protocol's 20 kBd maximum baud rate, where standardized LIN physical-layer behavior and compact package size simplify harness-based sub-networks.
When laying out the circuit, follow the pin-description table and recommended application circuit in the manufacturer datasheet. Pay particular attention to transceiver supply connections, ground return, LIN bus routing, external bus-interface components, and protection requirements. PCB signal integrity and automotive EMC performance depend on keeping the bus path compact and following the manufacturer's reference layout.
This product page combines NXP protocol-compliance information, drop-in family options, application guidance, and practical design notes to support component selection and PCB planning. It is intended to help engineers identify whether the TJA1027TK/20/1 matches the required LIN standard, package, bus rate, and automotive integration constraints.
Alternatives de remplacement direct pour TJA1027TK/20/1 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
TJA1020TK/20/1
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
TJA1021TK/20/1
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
TJA1027TK/20/1 Spécifications
| Product Type | LIN bus transceiver |
| LIN Protocol Support | LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A |
| Maximum LIN Baud Rate | 20 kBd |
| Automotive Standard | SAE J2602 |
| ISO Compliance | ISO 17987-4:2016 (12 V) |
| Boîtier | 8-pin HVSON, 3 mm x 3 mm |
| Type de montage | Surface mount |
| Automotive Application | In-vehicle LIN sub-networks |
| Transceiver Function | LIN master and slave physical-layer interface |
Guide de configuration des broches du TJA1027TK/20/1 8-pin hvson, 3 mm x 3 mm
Configuration des broches du TJA1027TK/20/1 (boîtier 8-pin hvson, 3 mm x 3 mm). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour TJA1027TK/20/1.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
TJA1027TK/20/1 convient pour 6 applications: Automotive LIN Master Node, Automotive LIN Slave Node, Body Control Module Interface, Vehicle Sensor Interface, Door and Seat Control Module, Automotive Lighting Controller.
Automotive LIN Master Node
The TJA1027TK/20/1 fits a LIN master node that connects a vehicle control module to a single-wire LIN sub-network operating at up to 20 kBd. Its support for LIN 2.2A, SAE J2602, and ISO 17987-4:2016 provides a standardized physical-layer basis for 12 V vehicle systems. Place the transceiver beside the LIN protocol controller, route the bus line directly to its LIN connection, and follow the NXP application circuit for supply decoupling, ground, and optional external bus components.
Recommandé
Automotive LIN Slave Node
The TJA1027TK/20/1 is suitable for a compact slave node connected to a LIN master over a 12 V vehicle sub-network. It supports baud rates up to 20 kBd and the LIN 2.0, 2.1, 2.2, and 2.2A protocol levels identified by NXP. In a sensor, switch, or actuator module, the transceiver converts the physical bus signal into a logic-side interface for the local controller. Its 8-pin HVSON package measures 3 mm by 3 mm, helping conserve board area in space-constrained modules.
Recommandé
Body Control Module Interface
The TJA1027TK/20/1 can provide the physical layer for LIN-connected body functions such as seat, door, lighting, and climate-control modules. The 20 kBd maximum baud rate matches the intended use of the device for in-vehicle sub-networks, while LIN 2.2A, SAE J2602, and ISO 17987-4:2016 support addresses standardized automotive network operation. Keep the LIN trace short and follow the manufacturer layout guidance to preserve signal integrity and contain electromagnetic emissions.
Recommandé
Vehicle Sensor Interface
The TJA1027TK/20/1 is appropriate for a remote LIN sensor that communicates with a vehicle body controller through a single-wire bus. The device provides the LIN physical-layer interface between the embedded protocol controller and the bus while supporting operation at up to 20 kBd. For a compact remote module, the 3 mm by 3 mm, 8-pin HVSON package is advantageous. Validate the complete node configuration, including bus termination, sleep behavior, supply range, and external protection.
Recommandé
Door and Seat Control Module
The TJA1027TK/20/1 can connect door, seat, window, or switch modules to a LIN-controlled vehicle sub-network. Its 20 kBd capability and stated support for LIN 2.2A and SAE J2602 are appropriate for low-bandwidth in-vehicle communication. Use the transceiver as the boundary between the module's LIN controller and the physical harness, while following the NXP reference layout for bus routing and grounding. This integration reduces wiring compared with a point-to-point interface.
Recommandé
Automotive Lighting Controller
The TJA1027TK/20/1 supports LIN-based lighting control modules that exchange commands and status over a vehicle sub-network. Its standardized LIN physical-layer coverage includes LIN 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V systems. The transceiver is placed beside the lighting controller so logic commands can reach the LIN bus with the correct physical signaling. Board design should account for the harness environment, including protection and electromagnetic compatibility requirements.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TJA1027TK/20/1 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TJA1020TK/20/1 | TJA1021TK/20/1 |
|---|---|---|---|
| Package | 8-pin HVSON, 3 mm x 3 mm | 8-pin HVSON, 3 mm x 3 mm | 8-pin HVSON, 3 mm x 3 mm |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Type | LIN transceiver | LIN transceiver | LIN transceiver |
| Primary Application | In-vehicle LIN sub-networks | Automotive LIN physical layer | Automotive LIN physical layer |
| Pin Compatibility | TJA1027 family is pin-compatible with TJA1020 and TJA1021 | Pin-compatible with TJA1027 family | Pin-compatible with TJA1027 family |
Principaux différenciateurs
- Explicit LIN 2.2A and SAE J2602 positioning (vs TJA1020TK/20/1)
- ISO 17987-4:2016 support for 12 V systems (vs TJA1021TK/20/1)
- Family-level drop-in migration path (vs TJA1020TK/20/1)
Notes de conception
Route the LIN bus connection directly to the transceiver and keep the trace short, with no unnecessary stubs or test pads that create discontinuities. Place the transceiver close to the LIN protocol controller to minimize logic-side trace length. Follow the component placement and bus-routing pattern in the NXP manufacturer datasheet, and provide a continuous ground reference beneath the relevant signal path.
Use the supply and ground connections exactly as defined in the TJA1027 manufacturer datasheet and place the recommended decoupling capacitors close to their associated pins. Do not infer the acceptable supply range from the nominal 12 V automotive system because transient protection and device limits are separate considerations. Validate cold-start, load-dump, and power-reset behavior against the vehicle electrical-environment requirements.
Design the LIN bus path for the physical harness rather than treating it as a conventional low-speed logic trace. Confirm the master and slave termination arrangement, trunk length, node spacing, and external protection components in the application circuit. These factors determine rise time, signal reflection, and disturbance immunity across the vehicle sub-network.
Automotive EMC performance depends on both device selection and implementation. Keep sensitive logic and clock signals away from the LIN bus trace, maintain short return paths, and use the manufacturer's recommended component placement. Review radiated and conducted emissions with the final harness, enclosure, connector, and neighboring power-converter layout because those elements are not represented by the transceiver package alone.
Informations de conformité
The device is intended for automotive LIN sub-networks, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated in the available manufacturer information.