NXP Semiconductors

TJA1027TK/20/1 - LIN 2.2A Transceiver | NXP

MPN: TJA1027TK/20/1 ✓ 啟用中
8-pin HVSON, 3 mm x 3 mm Package
MOQ: 1 |

TJA1027TK/20/1 概覽

NXP Semiconductors TJA1027TK/20/1 is an automotive LIN bus transceiver supporting data rates up to 20 kBd in an 8-pin HVSON package with a 3 mm by 3 mm body size. It is intended for in-vehicle sub-networks and complies with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 (12 V) requirements.

A Local Interconnect Network transceiver is the physical-layer interface between a LIN protocol controller and the vehicle's LIN wiring. It combines the bus transmitter, receiver, voltage-domain conversion, and protection functions required to connect a microcontroller-based master or slave node to a low-cost, single-wire automotive network. LIN belongs to the broader hierarchy of automotive interface ICs, communication transceivers, interface ICs, and semiconductors.

Key characteristics include operation at up to 20 kBd, compatibility with LIN 2.0 through LIN 2.2A, and compliance with SAE J2602 and ISO 17987-4:2016 for 12 V systems. The TJA1027 is pin-compatible with the TJA1020 and TJA1021 families, making it useful when a design must consolidate LIN transceiver sourcing while retaining the established physical footprint and board-level implementation.

The TJA1027 integrates the LIN physical-layer transmitter and receiver with logic-side supply support, allowing a protocol controller to communicate through the vehicle LIN bus. Its compliance targets cover both LIN 2.2A and SAE J2602 requirements, providing a defined basis for automotive sub-network designs. Exact operating limits, electrical thresholds, bus-loading limits, and transceiver timing should be checked against the manufacturer datasheet for the selected ordering code.

Typical uses include LIN master nodes, LIN slave nodes, body-control modules, seat and door modules, climate-control peripherals, switch interfaces, sensors, and lighting modules. The device is particularly relevant to 12 V vehicle architectures operating below the protocol's 20 kBd maximum baud rate, where standardized LIN physical-layer behavior and compact package size simplify harness-based sub-networks.

When laying out the circuit, follow the pin-description table and recommended application circuit in the manufacturer datasheet. Pay particular attention to transceiver supply connections, ground return, LIN bus routing, external bus-interface components, and protection requirements. PCB signal integrity and automotive EMC performance depend on keeping the bus path compact and following the manufacturer's reference layout.

This product page combines NXP protocol-compliance information, drop-in family options, application guidance, and practical design notes to support component selection and PCB planning. It is intended to help engineers identify whether the TJA1027TK/20/1 matches the required LIN standard, package, bus rate, and automotive integration constraints.

直接替換替代品,適用於 TJA1027TK/20/1 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

TJA1020TK/20/1

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin HVSON, 3 mm x 3 mm
NXP identifies TJA1020 pin compatibility; protocol version, supply limits, and exact ordering details must be matched for production use.

📋 參考替代品(不在目錄中)

TJA1021TK/20/1

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin HVSON, 3 mm x 3 mm
NXP identifies TJA1021 pin compatibility; protocol version, supply limits, and exact ordering details must be matched for production use.

📋 參考替代品(不在目錄中)

TJA1027TK/20/1 規格

Product Type LIN bus transceiver
LIN Protocol Support LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A
Maximum LIN Baud Rate 20 kBd
Automotive Standard SAE J2602
ISO Compliance ISO 17987-4:2016 (12 V)
封裝 8-pin HVSON, 3 mm x 3 mm
安裝類型 Surface mount
Automotive Application In-vehicle LIN sub-networks
Transceiver Function LIN master and slave physical-layer interface

TJA1027TK/20/1 8-pin hvson, 3 mm x 3 mm 腳位配置指南

TJA1027TK/20/1(8-pin hvson, 3 mm x 3 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

TJA1027TK/20/1 的 8-pin hvson, 3 mm x 3 mm 封裝腳位圖

無詳細腳位定義資料: TJA1027TK/20/1.

請參閱 資料表 以查看完整腳位配置。

典型應用

TJA1027TK/20/1 適用於 6 應用s: Automotive LIN Master Node, Automotive LIN Slave Node, Body Control Module Interface, Vehicle Sensor Interface, Door and Seat Control Module, Automotive Lighting Controller.

🚗

Automotive LIN Master Node

The TJA1027TK/20/1 fits a LIN master node that connects a vehicle control module to a single-wire LIN sub-network operating at up to 20 kBd. Its support for LIN 2.2A, SAE J2602, and ISO 17987-4:2016 provides a standardized physical-layer basis for 12 V vehicle systems. Place the transceiver beside the LIN protocol controller, route the bus line directly to its LIN connection, and follow the NXP application circuit for supply decoupling, ground, and optional external bus components.

🧩

Automotive LIN Slave Node

The TJA1027TK/20/1 is suitable for a compact slave node connected to a LIN master over a 12 V vehicle sub-network. It supports baud rates up to 20 kBd and the LIN 2.0, 2.1, 2.2, and 2.2A protocol levels identified by NXP. In a sensor, switch, or actuator module, the transceiver converts the physical bus signal into a logic-side interface for the local controller. Its 8-pin HVSON package measures 3 mm by 3 mm, helping conserve board area in space-constrained modules.

🚙

Body Control Module Interface

The TJA1027TK/20/1 can provide the physical layer for LIN-connected body functions such as seat, door, lighting, and climate-control modules. The 20 kBd maximum baud rate matches the intended use of the device for in-vehicle sub-networks, while LIN 2.2A, SAE J2602, and ISO 17987-4:2016 support addresses standardized automotive network operation. Keep the LIN trace short and follow the manufacturer layout guidance to preserve signal integrity and contain electromagnetic emissions.

📡

Vehicle Sensor Interface

The TJA1027TK/20/1 is appropriate for a remote LIN sensor that communicates with a vehicle body controller through a single-wire bus. The device provides the LIN physical-layer interface between the embedded protocol controller and the bus while supporting operation at up to 20 kBd. For a compact remote module, the 3 mm by 3 mm, 8-pin HVSON package is advantageous. Validate the complete node configuration, including bus termination, sleep behavior, supply range, and external protection.

🚪

Door and Seat Control Module

The TJA1027TK/20/1 can connect door, seat, window, or switch modules to a LIN-controlled vehicle sub-network. Its 20 kBd capability and stated support for LIN 2.2A and SAE J2602 are appropriate for low-bandwidth in-vehicle communication. Use the transceiver as the boundary between the module's LIN controller and the physical harness, while following the NXP reference layout for bus routing and grounding. This integration reduces wiring compared with a point-to-point interface.

💡

Automotive Lighting Controller

The TJA1027TK/20/1 supports LIN-based lighting control modules that exchange commands and status over a vehicle sub-network. Its standardized LIN physical-layer coverage includes LIN 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V systems. The transceiver is placed beside the lighting controller so logic commands can reach the LIN bus with the correct physical signaling. Board design should account for the harness environment, including protection and electromagnetic compatibility requirements.

推薦產品摘要

TJA1027T/20 Related NXP TJA1027 ordering variant 用於: Automotive LIN Master Node, Automotive LIN Slave Node, Vehicle Sensor Interface, Automotive Lighting Controller TJA1020TK/20/1 Pin-compatible NXP LIN transceiver family 用於: Automotive LIN Master Node, Body Control Module Interface, Door and Seat Control Module TJA1021TK/20/1 Pin-compatible NXP LIN transceiver family 用於: Automotive LIN Slave Node, Vehicle Sensor Interface, Automotive Lighting Controller TJA1027TK/20/1 NXP Semiconductors 用於: Body Control Module Interface, Door and Seat Control Module
What is the TJA1027TK/20/1?
The TJA1027TK/20/1 is an NXP Semiconductors LIN physical-layer transceiver for 12 V automotive sub-networks operating at up to 20 kBd. According to the manufacturer datasheet, it supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016. The device is packaged in an 8-pin HVSON package with a 3 mm by 3 mm body size.
What LIN standards does the TJA1027TK/20/1 support?
The TJA1027TK/20/1 supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V systems. The NXP manufacturer datasheet identifies the TJA1027 as an interface between a LIN protocol controller and the physical LIN bus. This standards coverage makes it suitable for low-speed vehicle sub-networks using master or slave node architectures.
What is the maximum baud rate of the TJA1027TK/20/1?
The TJA1027TK/20/1 supports LIN bus data rates up to 20 kBd. The manufacturer datasheet states that the transceiver is primarily intended for in-vehicle sub-networks using baud rates up to 20 kBd. Designers should ensure that the LIN controller baud-rate settings, bus timing, and overall network configuration remain within the protocol and device operating limits.
Is the TJA1027TK/20/1 pin-compatible with the TJA1020?
Yes, the NXP product information identifies the TJA1027 as pin-compatible with the TJA1020. The comparison applies at the family and pin-assignment level, so the exact replacement suffix, package, temperature grade, and ordering code should still be checked before production use. Existing boards designed around the corresponding TJA1020 footprint may therefore support a straightforward migration path to the TJA1027.
Is the TJA1027TK/20/1 pin-compatible with the TJA1021?
Yes, NXP identifies the TJA1027 as pin-compatible with the TJA1021. The manufacturer product page lists that relationship alongside TJA1020 compatibility. For an actual drop-in substitution, verify the selected TJA1021 ordering code has the same package, pin functions, electrical limits, protocol variant, and temperature grade as the TJA1027TK/20/1.
What can replace the TJA1027TK/20/1?
The most direct same-manufacturer replacement choices identified by NXP are TJA1020 and TJA1021, because the manufacturer explicitly states that the TJA1027 is pin-compatible with both families. No verified cross-manufacturer drop-in equivalent was identified for the exact 8-pin HVSON device. Confirm the complete ordering suffix, package dimensions, transceiver behavior, supply range, and automotive qualification before exchanging components.
TJA1027TK/20/1 vs TJA1020: which is better for a LIN sub-network?
Choose the TJA1027TK/20/1 when the design specifically needs LIN 2.2A, SAE J2602, and ISO 17987-4:2016 coverage. Choose a compatible TJA1020 ordering code when its protocol level and electrical ratings satisfy the vehicle program and the TJA1027 provides no required benefit. Both devices are identified as pin-compatible, but exact suffix and qualification matching remain essential.
TJA1027TK/20/1 vs TJA1021: which fits a LIN slave node?
The TJA1027TK/20/1 is suitable when a slave node requires explicit LIN 2.2A, SAE J2602, and ISO 17987-4:2016 support. A compatible TJA1021 may also fit when its protocol version, electrical characteristics, package, and qualification meet the application. Both families are identified as pin-compatible with the TJA1027, so the deciding factors are system requirements rather than basic connector compatibility.
When should I choose the TJA1027TK/20/1 over another LIN transceiver?
Select the TJA1027TK/20/1 when an automotive LIN node must meet the stated LIN 2.2A, SAE J2602, and ISO 17987-4:2016 requirements in a compact 3 mm by 3 mm HVSON package. It is especially suitable for 12 V vehicle sub-networks operating at up to 20 kBd. Prefer another transceiver only when its exact ordering code provides equivalent protocol, electrical, package, and qualification requirements.
Is the TJA1027TK/20/1 suitable for automotive body modules?
Yes, the TJA1027TK/20/1 is suitable for automotive body modules that use a LIN sub-network. The NXP manufacturer datasheet identifies in-vehicle sub-networks as the primary application and specifies support for LIN 2.0 through LIN 2.2A plus SAE J2602 and ISO 17987-4:2016. Its 8-pin, 3 mm by 3 mm HVSON package also supports compact PCB layouts.
Where can I download the TJA1027TK/20/1 datasheet PDF?
The official TJA1027 datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1027.pdf. Use the pin-description table, electrical characteristics, timing diagrams, and application circuit for design work. The ordering-code table should also be checked to confirm the exact features associated with TJA1027TK/20/1.
Where can I find the TJA1027TK/20/1 pinout?
The authoritative pinout is shown in the NXP TJA1027 manufacturer datasheet and its pin-description table. Use that table when assigning the 8-pin HVSON connections, including transceiver supply, ground, logic-side interfaces, and LIN bus connection. The verified listing identifies the package as 8-pin HVSON with a 3 mm by 3 mm body size.
Where can I buy the TJA1027TK/20/1 online?
Use the Request a Quote form on this page to request the TJA1027TK/20/1, current lead time, minimum order quantity, and order confirmation. Stock status is not established by an indexed catalog page, so do not infer immediate availability from a product listing alone. The request can be tied to the exact TJA1027TK/20/1 ordering code and 8-pin HVSON package requirements.
What is the price of the TJA1027TK/20/1?
Current pricing for the TJA1027TK/20/1 should be obtained through the Request a Quote form on this page. The available catalog pages do not provide qualifying quantity-break prices for this exact ordering code, so no numerical price is stated here. A quote should specify the manufacturer part number, quantity, and required delivery configuration to avoid ambiguity with related TJA1027 order codes.
What is the lead time and stock status for the TJA1027TK/20/1?
The current stock status and lead time for the TJA1027TK/20/1 should be requested through the Request a Quote form on this page. An indexed distributor page confirms that the device is a cataloged NXP LIN transceiver, but it does not establish a guaranteed stock quantity or production lead time. Include the required quantity, date code needs, and approved package suffix in the request.
What are the key specifications of TJA1027TK/20/1 that engineers should know?
The key TJA1027TK/20/1 specifications are a maximum LIN rate of 20 kBd, support for LIN 2.0 through LIN 2.2A, SAE J2602 compliance, and ISO 17987-4:2016 compliance for 12 V systems. NXP describes the device as a LIN master or slave physical-layer interface for in-vehicle sub-networks, and distributor information identifies an 8-pin HVSON package measuring 3 mm by 3 mm.
Does the TJA1027TK/20/1 require external bus protection components?
The external protection and termination requirements depend on the complete LIN network topology, bus length, number of nodes, and vehicle EMC design. According to the NXP manufacturer datasheet, the application circuit and interface guidance define the recommended implementation. Follow those reference connections and PCB-layout instructions rather than adding or omitting bus components without checking the complete network design.

工程參考資料,適用於 TJA1027TK/20/1 — 比較、設計指引及合規資訊。

選型指南

Choose the TJA1027TK/20/1 for a 12 V automotive LIN node that specifically calls for LIN 2.2A, SAE J2602, and ISO 17987-4:2016 compliance and uses an 8-pin, 3 mm by 3 mm HVSON footprint. Consider TJA1020TK/20/1 when its exact protocol coverage and electrical limits meet the program requirements and the established TJA1020 implementation offers a simpler sourcing path; NXP explicitly identifies the two families as pin-compatible. Consider TJA1021TK/20/1 for the same reason after checking its exact ordering suffix and requirements. No verified cross-manufacturer drop-in equivalent was established, so an alternate supplier should not be treated as a direct replacement without package, pin, electrical, protocol, and qualification evidence.

與替代品比較

參數 本產品 TJA1020TK/20/1 TJA1021TK/20/1
Package 8-pin HVSON, 3 mm x 3 mm 8-pin HVSON, 3 mm x 3 mm 8-pin HVSON, 3 mm x 3 mm
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors
Product Type LIN transceiver LIN transceiver LIN transceiver
Primary Application In-vehicle LIN sub-networks Automotive LIN physical layer Automotive LIN physical layer
Pin Compatibility TJA1027 family is pin-compatible with TJA1020 and TJA1021 Pin-compatible with TJA1027 family Pin-compatible with TJA1027 family

主要差異化特點

  • Explicit LIN 2.2A and SAE J2602 positioning (對比TJA1020TK/20/1)
  • ISO 17987-4:2016 support for 12 V systems (對比TJA1021TK/20/1)
  • Family-level drop-in migration path (對比TJA1020TK/20/1)

設計說明

Route the LIN bus connection directly to the transceiver and keep the trace short, with no unnecessary stubs or test pads that create discontinuities. Place the transceiver close to the LIN protocol controller to minimize logic-side trace length. Follow the component placement and bus-routing pattern in the NXP manufacturer datasheet, and provide a continuous ground reference beneath the relevant signal path.

Use the supply and ground connections exactly as defined in the TJA1027 manufacturer datasheet and place the recommended decoupling capacitors close to their associated pins. Do not infer the acceptable supply range from the nominal 12 V automotive system because transient protection and device limits are separate considerations. Validate cold-start, load-dump, and power-reset behavior against the vehicle electrical-environment requirements.

Design the LIN bus path for the physical harness rather than treating it as a conventional low-speed logic trace. Confirm the master and slave termination arrangement, trunk length, node spacing, and external protection components in the application circuit. These factors determine rise time, signal reflection, and disturbance immunity across the vehicle sub-network.

Automotive EMC performance depends on both device selection and implementation. Keep sensitive logic and clock signals away from the LIN bus trace, maintain short return paths, and use the manufacturer's recommended component placement. Review radiated and conducted emissions with the final harness, enclosure, connector, and neighboring power-converter layout because those elements are not represented by the transceiver package alone.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The device is intended for automotive LIN sub-networks, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated in the available manufacturer information.

資料驗證日期: 2026-11-09 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

TJA1027TK/20/1 datasheet TJA1027TK/20/1 pinout TJA1027TK/20/1 datasheet pdf TJA1027TK/20/1 equivalent TJA1027TK/20/1 replacement TJA1027TK/20/1 price TJA1027TK/20/1 stock NXP TJA1027TK/20/1 TJA1027TK/20/1 20 kBd TJA1027TK/20/1 HVSON pinout TJA1027TK/20/1 automotive LIN TJA1027TK/20/1 vs TJA1020TK/20/1 TJA1027TK/20/1 application circuit

相關元件與詞彙

NXP Semiconductors TJA1027TK/20/1 TJA1020TK/20/1 TJA1021TK/20/1 TJA1027 LIN transceiver Local Interconnect Network automotive interface IC physical-layer transceiver communication transceiver interface IC semiconductor LIN 2.0 LIN 2.1 LIN 2.2 LIN 2.2A SAE J2602 ISO 17987-4:2016 8-pin HVSON 3 mm by 3 mm package surface-mount package 20 kBd automotive sub-network 12 V automotive system
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情