TLV2462QD - Dual RRIO 6.4MHz Op Amp | Texas Instruments
Référence : TLV2462QD ✓ ActifTLV2462QD Présentation
An operational amplifier is a voltage-gain component used to amplify small signals, buffer voltage sources, compare analog thresholds, and support feedback-based signal conditioning. The TLV2462 belongs to the operational-amplifier, analog-signal-conditioning, and power-management-IC hierarchy. Rail-to-rail input capability allows the amplifier to accept input voltages near the supply rails, while rail-to-rail output capability supports operation with limited output-voltage headroom.
The TLV2462QD provides two amplifier channels in one package, reducing board area compared with separate single-channel devices. Its 6.4 MHz gain-bandwidth product supports signal paths requiring moderate bandwidth, and its specified 80 mA output-drive capability is useful for driving moderate loads. The manufacturer describes the family as low power, with a quoted supply current of 500 µA per channel, making it applicable to portable instrumentation and other compact battery-operated systems.
Both channels share the same supply pins, but each channel can be configured independently as an amplifier, buffer, comparator, or active-filter element. The common package and dual-channel organization also simplify power distribution and reduce the number of external components required for dual-signal conditioning. Configuration depends on the feedback network, input impedance, source impedance, output loading, and required stability.
Typical uses include portable sensor interfaces, low-level analog signal amplification, voltage buffering, threshold detection, audio preamplification, and general-purpose analog conditioning. The 6 V rating supports low-voltage systems, while the 8-pin SOIC package allows conventional surface-mount assembly. Care is still required when operating near the supply rails, driving capacitive loads, or selecting feedback values for stable closed-loop response.
For design planning, verify the complete electrical limits and pin assignments in the manufacturer datasheet before layout release. Decoupling capacitors should be placed close to the supply pins, input and output routing should minimize parasitic capacitance, and unused amplifier inputs must be tied to a defined potential rather than left floating. This page combines package, performance, application, and replacement guidance to support early design decisions.
Alternatives de remplacement direct pour TLV2462QD — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec TLV2462QD (même facteur de forme et même empreinte) — différant par Amplifier Type, Package, Input Common-Mode Range, Output Swing, RoHS Status.
TLV2462ID
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →TLV2462CD
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →TLV2462QDRG4Q1
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TLV2462IP
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
TLV2462CP
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
TLV2462QD Valeurs maximales et caractéristiques électriques
| Amplifier Type | Operational Amplifier |
| Number of Channels | 2 channels |
| Topologie | Dual |
| Rail-to-Rail Input | Yes |
| Rail-to-Rail Output | Yes |
| Gain-Bandwidth Product | 6.4 MHz |
| Output Drive Capability | 80 mA |
| Courant d'alimentation | 500 µA/channel |
| Maximum Supply Voltage | 6 V |
| Boîtier | 8-pin SOIC |
| Type de montage | Surface Mount |
| Automotive Qualification | AEC-Q100 |
Guide de configuration des broches du TLV2462QD 8-pin soic
Configuration des broches du TLV2462QD (boîtier 8-pin soic). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour TLV2462QD.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
TLV2462QD convient pour 6 applications: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Audio Preamplification, Threshold and Comparator Circuits, Low-Voltage Active Filtering, Automotive Low-Voltage Analog Interface.
Portable Sensor Signal Conditioning
The TLV2462QD fits portable sensor-conditioning circuits because it combines two rail-to-rail operational-amplifier channels, a 6.4 MHz gain-bandwidth product, and 500 µA supply current per channel. One channel can amplify a low-level sensor signal while the other provides buffering or threshold detection. Place each device close to the sensor interface, use short feedback paths, and include local supply bypassing to limit noise pickup. Rail-to-rail input and output operation is especially useful when the measured signal approaches a supply rail, although the selected gain, source impedance, and output loading must satisfy the amplifier's stability and common-mode limits.
Recommandé
Battery-Powered Instrumentation
The TLV2462QD is appropriate for compact, battery-powered measurement equipment where two analog channels are required without the board area of separate single amplifiers. Its quoted 500 µA supply current per channel and dual-channel 8-pin SOIC package support power- and space-conscious designs. The 6.4 MHz gain-bandwidth product provides useful signal bandwidth for sensor signals and low-frequency instrumentation. Designers should account for the complete amplifier supply current, reference-circuit demand, sensor current, and output activity when calculating battery life, while using the enable or shutdown strategy described in the family documentation if the final platform includes that function.
Recommandé
Audio Preamplification
The dual-channel TLV2462QD can support stereo or dual-channel low-level audio preamplification where rail-to-rail operation and a 6.4 MHz gain-bandwidth product are valuable. The stated 80 mA output-drive capability provides margin for moderate source and load conditions, but the external audio source impedance and capacitive load determine the practical response. Use balanced feedback values, keep input traces away from supply and output routes, and verify output swing against the required signal amplitude. Because the device is a general-purpose operational amplifier rather than an audio-specific part, system-level noise, distortion, and stability requirements should be confirmed through the family datasheet and prototype measurements.
Recommandé
Threshold and Comparator Circuits
The TLV2462QD can implement two threshold-detection channels by applying feedback or positive feedback to create comparator-like behavior. Rail-to-rail input and output capability increases usable signal range in low-voltage systems, while the 6.4 MHz gain-bandwidth product supports signals beyond the audio band. Layout remains important even in a slow threshold circuit because high gain can amplify high-frequency noise or cause output transitions to interact with parasitic capacitance. Keep the reference network stable, connect the unused input channel to a defined common-mode potential, and validate output logic levels and transition behavior in the intended supply range before treating the amplifier as a logic comparator.
Recommandé
Low-Voltage Active Filtering
The dual TLV2462QD is well suited to low-voltage active-filter and active-filter-adjacent designs that need moderate bandwidth and flexible gain setting. Its 6.4 MHz gain-bandwidth product provides the closed-loop bandwidth required for many low-frequency filter stages, while the dual package simplifies implementation of paired pole or signal-path functions. Component tolerances, amplifier noise, input bias current, and output loading can alter filter behavior. Keep the two channels in thermally and spatially similar conditions when matching matters, use short feedback paths, and check stability with the intended source and load. Follow the manufacturer’s recommended application circuits when reproducing established filter topologies.
Recommandé
Automotive Low-Voltage Analog Interface
The TLV2462QD is suitable for low-voltage automotive analog interfaces because the Q suffix denotes an automotive-qualified ordering option and the device provides two rail-to-rail amplifier channels in an 8-pin SOIC package. Its 6 V maximum supply rating and 6.4 MHz gain-bandwidth product fit many sensor, control, and signal-conditioning blocks. Automotive implementation must also satisfy the complete TLV2462-Q1 qualification requirements rather than relying only on the suffix. Validate transient immunity, input protection, grounding, noise behavior, and operating temperature against the vehicle platform requirements, and use the manufacturer’s automotive qualification documentation for production release.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TLV2462QD — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TLV2462ID | TLV2462CD | TLV2462QDRG4Q1 | TLV2462IP | TLV2462CP |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Amplifier Type | Low-power operational amplifier | Low-power operational amplifier | Low-power operational amplifier | Low-power operational amplifier | Low-power operational amplifier | Low-power operational amplifier |
| Gain-Bandwidth Product | 6.4 MHz | 6.4 MHz | 6.4 MHz | 6.4 MHz | 6.4 MHz | 6.4 MHz |
| Supply Current | 500 µA/channel | 500 µA/channel | 500 µA/channel | 500 µA/channel | 500 µA/channel | 500 µA/channel |
| Output Drive Capability | 80 mA | 80 mA | 80 mA | 80 mA | 80 mA | 80 mA |
| Maximum Supply Voltage | 6 V | 6 V | 6 V | 6 V | 6 V | 6 V |
| Rail-to-Rail Input and Output | Yes | Yes | Yes | Yes | Yes | Yes |
Principaux différenciateurs
- Combines two rail-to-rail amplifier channels in one package (vs TLV2462QDRG4Q1)
- Automotive-qualified ordering option (vs TLV2462ID)
- Low-power dual amplification for compact analog systems (vs TLV2462CD)
Notes de conception
Place the supply-decoupling capacitor immediately adjacent to the device supply pins, and route the connection with minimal loop area. Keep input and feedback traces short and separated from output and supply-current paths. This reduces parasitic coupling into the rail-to-rail input stage, where small signals may occupy only a limited voltage range above the lower rail.
Do not leave either operational-amplifier input floating. An unused channel should be configured as a stable unity-gain buffer or tied to a defined common-mode voltage, with its output arranged so it cannot interfere with the used channel. Floating inputs can collect noise and cause unintended oscillation, even though the active channel appears electrically correct.
Account for the 6.4 MHz gain-bandwidth product when selecting feedback resistors and capacitors. Large feedback impedances can introduce parasitic-capacitance errors, while large capacitive loads can destabilize the output. Use short, direct feedback routing and verify the final source impedance, load, supply configuration, and operating gain against the stability guidance in the manufacturer datasheet.
Calculate total supply demand from both amplifier channels and all board loads. The quoted 500 µA per channel applies to the amplifier family, but battery and regulator sizing must also include output-current peaks, the stated 80 mA output-drive capability, nearby circuitry, and transient requirements. Ensure the source can support the required supply range without forcing the amplifier outside its operating limits.
Informations de conformité
The TLV2462QD is identified as AEC-Q100 automotive grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or lot documentation.