TPSM33615FRDNR - 36V 1.5A Sync Buck Module | Texas Instruments
Référence : TPSM33615FRDNR ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $4.2 | $4,20 |
| 10 | $3.78 | $37,80 |
| 100 | $3.36 | $336,00 |
| 500 | $3.02 | $1 510,00 |
| 1 000 | $2.69 | $2 690,00 |
TPSM33615FRDNR Présentation
A buck converter (step-down switching regulator) is a switching-converter topology that reduces a higher DC input voltage to a lower regulated DC output voltage using an inductor, capacitor, and synchronous MOSFET switches. It sits within the broader power management IC hierarchy: buck converter -> DC-DC converter -> switching regulator -> power management IC. A power module such as the TPSM33615FRDNR integrates the controller, MOSFETs, inductor, and compensation network into one package, simplifying PCB layout and reducing design risk versus discrete buck implementations.
Key features include 1.5-uA quiescent current, 1-MHz fixed switching frequency, programmable output voltage from 1 V to 15 V, and selectable PFM or FPWM light-load operation. The HotRod QFN-FCMOD package reduces parasitic inductance and improves thermal performance. Integrated protections include over-current, over-temperature, under-voltage lockout, automatic fault recovery, and 1% output voltage accuracy across load and line. The integrated inductor and shielding minimize radiated EMI, which is critical for industrial and instrumentation applications that must pass CISPR 25 or CISPR 32.
Technically, the TPSM33615FRDNR uses a peak current-mode control topology with internal compensation, an external RT resistor to program switching frequency, and a MODE pin to select PFM (light-load efficiency) versus FPWM (constant-frequency low-noise) behavior. The HotRod flip-chip QFN package eliminates bond wires, reducing switching-node ringing and DC resistance losses.
Typical applications include industrial 24-V rail point-of-load regulation, factory automation sensors, building automation controllers, low-noise bias supplies for analog front ends, and portable or battery-powered equipment operating from multi-cell lithium packs. The wide 3-V to 36-V input range supports 12-V and 24-V industrial buses directly.
When designing with this device, keep the input capacitors close to VIN and PGND pins to minimize switching-node ringing, and connect the exposed thermal pad to a sufficient ground copper pour. Select PFM mode for highest light-load efficiency, or FPWM when low EMI is the top priority.
This page synthesizes distributor pricing, drop-in alternatives, design notes, and application guidance not found in the manufacturer datasheet alone, giving engineers a single reference for component selection, PCB implementation, and sourcing decisions.
Alternatives de remplacement direct pour TPSM33615FRDNR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
TPSM33615RDNR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPSM33625FRDNR
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
TPSM33625RDNR
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
TPSM365R6FRDNR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPSM365R15FRDNR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TPSM33615FRDNR Valeurs maximales et caractéristiques électriques
| Topologie | Synchronous Buck (Step-Down) Power Module |
| Plage de tension d'entrée | 3 V to 36 V |
| Plage de tension de sortie | 1 V to 15 V (programmable) |
| Courant de sortie maximal | 1.5 A |
| Fréquence de commutation | 1 MHz (typ, programmable via RT) |
| Courant de repos | 1.5 uA (typ) |
| Rendement | 88% (typ) |
| Output Voltage Accuracy | ±1% |
| Light-Load Operation | Selectable PFM or FPWM (via MODE pin) |
| Boîtier | QFN-FCMOD HotRod (RDN), 11 pins, 3.5 mm x 4.5 mm |
| Plage de température de fonctionnement | -40 C to +125 C |
| Type de montage | Surface Mount |
| Integrated Inductor | Yes (internal) |
| Protections | Over-Current, Over-Temperature, Under-Voltage Lockout, Automatic Fault Recovery |
| Statut RoHS | Compliant |
Configuration des broches de TPSM33615FRDNR
| Broche 1 | VIN — Input voltage supply (3V to 36V) |
| Broche 2 | PGND — Power ground return |
| Broche 3 | VIN — Input voltage supply (3V to 36V) |
| Broche 4 | EN — Enable (active high) |
| Broche 5 | MODE — PFM/FPWM mode select (FR variant only) |
| Broche 6 | RT — Switching frequency programming resistor |
| Broche 7 | FB — Feedback (output voltage sense) |
| Broche 8 | VOUT — Regulated output voltage |
| Broche 9 | PGND — Power ground return |
| Broche 10 | AGND — Analog ground |
| Broche 11 | PGND — Power ground return (exposed thermal pad) |
Applications typiques
TPSM33615FRDNR convient pour 6 applications: Industrial 24V Rail Point-of-Load, Building Automation Controllers, Portable Battery-Powered Equipment, Sensor and Analog Front-End Bias, Motor Control Auxiliary Rails, Automotive 12V Body Electronics.
Industrial 24V Rail Point-of-Load
The TPSM33615FRDNR steps down a 24-V industrial bus rail to logic-level voltages (3.3 V, 5 V, 12 V) for factory automation controllers, PLC I/O modules, and sensor conditioning boards. The 3-V to 36-V input range directly tolerates 24-V nominal with margin for transients, and the integrated inductor simplifies PCB layout in space-constrained DIN-rail enclosures. Compared to discrete buck designs, the module approach reduces EMI risk and shrinks the BOM, while the 88% typical efficiency keeps thermal rise manageable in sealed housings. Recommended companion parts include TI isolation and gate drivers for adjacent high-voltage stages.
Recommandé
Building Automation Controllers
Building automation systems such as HVAC controllers, smart lighting hubs, and access control panels often require multiple low-voltage rails from a 24-V AC/DC bus. The TPSM33615FRDNR's 1.5-A output, 1.5-uA quiescent current, and PFM light-load mode deliver excellent standby efficiency for always-on systems. The integrated protections (OCP, OTP, UVLO) satisfy UL and IEC safety expectations for building equipment. The 11-pin QFN-FCMOD HotRod package enables compact PCB designs inside wall-mounted enclosures where board area is at a premium.
Recommandé
Portable Battery-Powered Equipment
The TPSM33615FRDNR suits portable, battery-powered applications including handheld test instruments, two-way radios, and battery-powered sensors powered by 2S-8S lithium-ion packs (6 V to 36 V). The 1.5-uA quiescent current minimizes standby drain, and the 88% peak efficiency extends runtime under load. The HotRod QFN package provides robust thermal performance for handheld enclosures, and the 1-MHz switching frequency keeps the external filter small. The TPSM33615FRDNR's wide input range covers the full discharge curve of multi-cell battery packs without requiring a separate pre-regulator.
Recommandé
Sensor and Analog Front-End Bias
Precision sensor and analog front-end (AFE) circuits require low-noise, accurate voltage rails to preserve measurement integrity. The TPSM33615FRDNR delivers ±1% output voltage accuracy and selectable FPWM mode for low-noise constant-frequency operation, making it suitable for ADC reference rails, sensor excitation, and instrumentation amplifier supplies. When paired with a downstream low-dropout LDO such as the TPS7A30 or TPS7A47 series, the system achieves both high efficiency and ultra-low noise for sensitive analog signal chains.
Recommandé
Motor Control Auxiliary Rails
Brushless DC (BLDC) and stepper motor control boards typically require multiple low-voltage rails (3.3 V, 5 V) for microcontroller, gate driver, and communication logic from a 12-V or 24-V power input. The TPSM33615FRDNR's 36-V input tolerance handles motor back-EMF transients on shared bus rails. The integrated inductor and small QFN-FCMOD footprint minimize PCB area near motor driver stages where space is constrained, and the high 1-MHz switching frequency keeps fundamental switching noise above the audible band.
Recommandé
Automotive 12V Body Electronics
Although not AEC-Q100 qualified, the TPSM33615FRDNR suits non-safety automotive body electronics such as infotainment accessories, interior lighting controllers, and HVAC control modules operating from a 12-V battery bus. The 3-V to 36-V input range covers load-dump transients up to 36 V, while integrated UVLO prevents operation during cold-crank. For AEC-Q100-qualified designs in the same RDN footprint, TI's automotive-grade TPSM365R6-Q1 series is the recommended drop-in alternative.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TPSM33615FRDNR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TPSM33615RDNR | TPSM33625FRDNR | TPSM33625RDNR | TPSM365R6FRDNR | TPSM365R15FRDNR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | QFN-FCMOD HotRod (RDN) 11-pin | QFN-FCMOD HotRod (RDN) 11-pin - same | QFN-FCMOD HotRod (RDN) 11-pin - same | QFN-FCMOD HotRod (RDN) 11-pin - same | QFN-FCMOD HotRod (RDN) 11-pin - same | QFN-FCMOD HotRod (RDN) 11-pin - same |
| Input Voltage Range | 3 V to 36 V | 3 V to 36 V - same | 3 V to 36 V - same | 3 V to 36 V - same | 3 V to 65 V - extended | 3 V to 65 V - extended |
| Maximum Output Current | 1.5 A | 1.5 A - same | 2.5 A - +67% | 2.5 A - +67% | 0.6 A - -60% | 0.15 A - -90% |
| Output Voltage Range | 1 V to 15 V | 1 V to 15 V - same | 1 V to 15 V - same | 1 V to 15 V - same | 1 V to 18 V - extended | 1 V to 18 V - extended |
| Light-Load Mode | Selectable PFM/FPWM (MODE pin) | Fixed PFM - reduced flexibility | Selectable PFM/FPWM - same | Fixed PFM - reduced flexibility | Selectable PFM/FPWM - same | Selectable PFM/FPWM - same |
| Switching Frequency | 1 MHz (RT programmable) | 1 MHz - same | 1 MHz - same | 1 MHz - same | ~1 MHz - similar | ~1 MHz - similar |
Principaux différenciateurs
- Selectable PFM/FPWM mode via dedicated pin (vs TPSM33615RDNR)
- Higher output current at same footprint (vs TPSM365R6FRDNR)
- Wide 36-V input tolerance covers 24-V industrial buses (vs TPSM365R15FRDNR)
Notes de conception
The TPSM33615FRDNR's HotRod QFN-FCMOD package achieves low thermal resistance via the exposed thermal pad, but junction temperature still depends on PCB copper area. Estimated: at VIN=24V, VOUT=5V, IOUT=1.5A, power dissipation is roughly (24-5)*1.5/0.88 = 32.4W input minus ~11.5W output = ~3.2W internal loss; with a 1-oz copper pour of 1 sq inch (theta_JA ~35 C/W), junction rise is ~112 C above ambient. For continuous 1.5-A operation at high VIN, larger copper area or airflow is recommended. Keep the thermal pad soldered to a continuous ground plane for optimal heat spreading.
Place the input bypass capacitors as close as possible to the VIN and PGND pins of the TPSM33615FRDNR, using short, wide traces to minimize switching-node parasitic inductance. According to TI's TPSM33615 datasheet, a 1-uF to 10-uF ceramic input capacitor plus a 0.1-uF high-frequency bypass is recommended. The MODE and RT pins are sensitive to noise; route these traces away from the switching node (VOUT/SW). Connect the exposed thermal pad to a solid ground copper pour with multiple thermal vias for low thermal impedance.
Do not leave the MODE pin floating on TPSM33615FRDNR - per TI E2E forum discussions, an undefined MODE state can cause instability or unintended FPWM/PFM transitions. Tie MODE high for FPWM (low noise) or low for PFM (high efficiency). The RT pin must be connected to a valid programming resistor or GND; a noisy RT pin can cause switching-frequency jitter and increased VIN ripple (per TI engineer feedback). Do not exceed 36 V on VIN, and verify the upstream input protection handles load-dump transients up to 40 V if used in automotive 12-V environments.
The HotRod QFN-FCMOD package significantly reduces radiated EMI versus standard QFN, but additional filtering may be required for CISPR 25 / CISPR 32 Class B compliance in sensitive applications. According to TI's TPSM33615 datasheet, a small input pi-filter (ferrite bead plus 1-uF ceramic) typically achieves compliance with margin. Use FPWM mode when low EMI is the priority, since PFM produces variable-frequency harmonics that can fall into sensitive bands.
Informations de conformité
RoHS compliant per JLCPCB parametric listing. Not AEC-Q100 qualified - for AEC-Q100 automotive applications, contact TI for the automotive-grade TPSM336x5-Q1 family. Halogen-free status not explicitly stated in verified data.
