TS512IDT - 3MHz Dual Precision Op Amp | STMicroelectronics
Référence : TS512IDT ✓ ActifTS512IDT Présentation
An operational amplifier, or op amp, is a high-gain differential amplifier that uses external feedback to set gain and filtering behavior. In the electronics hierarchy, the TS512IDT is a precision operational amplifier within the broader amplifier IC and analog signal-processing categories. Its two independent channels allow one package to process two signals, while internal frequency and phase compensation simplify voltage-follower and other high-gain configurations without external compensation components.
The principal features include 3 MHz gain-bandwidth product, 8 nV/√Hz noise density, 0.03% distortion, low power consumption, short-circuit protection, and high channel separation. Operation from a single 3 V to 30 V supply or from dual ±1.5 V to ±15 V rails gives designers flexibility across industrial, instrumentation, and signal-conditioning systems. The low-noise and low-distortion characteristics are particularly relevant when small sensor and audio signals must be amplified without adding substantial broadband noise or harmonic distortion.
Internally compensated architecture supports stable operation in voltage-follower configurations despite the amplifier's relatively high gain-bandwidth product. The TS512x family is designed for general-purpose precision applications where clean signal amplification matters more than very high speed. Two channels in one package reduce board-area requirements, while high channel separation helps maintain signal integrity when the channels process related low-level signals. The amplifier also includes ESD protection and a macromodel for circuit simulation.
Typical uses include audio preamplification, instrumentation-amplifier input stages, active filters, sensor signal conditioning, transducers, and general-purpose analog measurement chains. The 8-pin SOIC package is useful where conventional surface-mount assembly is required and the circuit operates across the stated -40°C to +125°C temperature range. The wide supply-voltage range also permits operation from industrial rails while retaining compatibility with lower-voltage analog systems.
Designers should verify input and output voltage limits, common-mode range, output-swing behavior, and stability against the exact load connected to each channel. Decoupling capacitors should be placed close to the supply pins, while sensitive-input routing should avoid nearby switching nodes and high-current return paths. The dual package does not require matched channels for general use, but input bias-current and offset behavior must be considered in precision DC measurements.
This page combines the TS512IDT's principal electrical characteristics with pin-compatible family alternatives, application guidance, comparison parameters, and practical circuit-design notes. These engineering-focused details help shorten component evaluation and support a more reliable transition from initial schematic design through PCB implementation and production qualification.
Alternatives de remplacement direct pour TS512IDT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec TS512IDT (même facteur de forme et même empreinte) — différant par Gain-Bandwidth Product, Input Voltage Noise Density, Operating Temperature Range, Package.
TS512AIDT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
TS512IYDT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MC33078D
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →TS512IDT Valeurs maximales et caractéristiques électriques
| Amplifier Type | Dual precision operational amplifier |
| Number of Circuits | 2 |
| Gain-Bandwidth Product | 3 MHz |
| Input Voltage Noise Density | 8 nV/√Hz |
| Distortion | 0.03% |
| Single-Supply Operating Range | 3 V to 30 V |
| Dual-Supply Operating Range | ±1.5 V to ±15 V |
| Plage de température de fonctionnement | -40°C to +125°C |
| ESD Protection | 2 kV |
| Boîtier | 8-pin SOIC |
| Type de montage | Surface Mount |
| Compensation | Internal frequency and phase compensation |
| Short-Circuit Protection | Yes |
| Simulation Support | Macromodel included |
Guide de configuration des broches du TS512IDT 8-pin soic
Configuration des broches du TS512IDT (boîtier 8-pin soic). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour TS512IDT.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
TS512IDT convient pour 6 applications: Audio Preamplifier, Industrial Sensor Conditioning, Precision Active Filter, Instrumentation Measurement Front End, Data Acquisition Analog Front End, Portable Measurement Device.
Audio Preamplifier
The TS512IDT fits low-level audio preamplification because its 8 nV/√Hz input-voltage noise density supports small-signal amplification, while the 0.03% distortion specification limits added harmonic error. Place one channel in a gain stage and use the second channel for an active low-pass or output driver. The internally compensated amplifier operates stably as a voltage follower, which simplifies buffering after the gain-setting network. Keep input return paths short and use the highest practical gain in the first stage to minimize the contribution from the following stage.
Recommandé
Industrial Sensor Conditioning
The TS512IDT is appropriate for conditioning weak signals from resistive, piezoelectric, and low-level industrial sensors because its 8 nV/√Hz noise density supports low-noise amplification and its 3 MHz gain-bandwidth product covers moderate sensor bandwidths. The two channels can amplify a sensor input and provide an active filter or reference-buffer stage. Its single-supply operation from 3 V to 30 V allows integration near industrial rails. Grounding, shield routing, common-mode range, and output-swing limits remain the principal checks when the sensor environment introduces large transients or ground-potential differences.
Recommandé
Precision Active Filter
The TS512IDT can implement a second-order active filter because each channel provides independent gain and filtering through external resistors and capacitors, while internal frequency and phase compensation supports stable voltage-follower use. Its 3 MHz gain-bandwidth product leaves useful bandwidth above audio and many control-signal ranges. The 0.03% distortion specification is valuable when filtering low-level analog information. Select resistor and capacitor tolerances according to the required cutoff accuracy, and verify phase margin with the actual load because passive tolerances and input capacitance can alter the intended response.
Recommandé
Instrumentation Measurement Front End
The TS512IDT suits instrumentation front ends that amplify small differential or single-ended measurement signals while preserving low noise and low distortion. One channel can provide gain, and the second can form a unity-gain buffer or active gain stage for a non-inverting topology. The broad 3 V to 30 V single-supply range supports multiple industrial configurations. Input bias current, offset voltage, common-mode range, and output settling behavior should be evaluated against the sensor impedance and required accuracy. High-impedance guarding around the input nodes can reduce leakage-induced error.
Recommandé
Data Acquisition Analog Front End
The TS512IDT can provide the analog gain and buffering stage between a sensor and an ADC in a moderate-speed data-acquisition system. Its 3 MHz gain-bandwidth product is suitable for signals well below that bandwidth, while 8 nV/√Hz noise density and 0.03% distortion support accurate capture of small signals. The dual configuration can amplify and filter two channels or provide differential gain and common-mode handling. Select the gain so the ADC input range is not exceeded, then confirm the amplifier's output-swing limit and settling time against the sampling rate.
Recommandé
Portable Measurement Device
The TS512IDT is useful in portable measurement equipment where low-noise amplification and compact dual-channel integration are important. The device can operate from a 3 V single supply, while its low-noise characteristics help preserve small measurement signals without introducing excessive broadband noise. Internal compensation simplifies follower-based filtering and buffering, reducing external component count. Battery-operated designs should still verify supply current, dropout behavior, shutdown strategy, and thermal rise for the selected operating voltage. Guard sensitive inputs against connector charge, display-switching noise, and charger transients.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour TS512IDT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | TS512AIDT | TS512IYDT | MC33078D |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC - same package | 8-pin SOIC - same package | 8-pin SOIC - same package |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Motorola |
| Number of Amplifier Channels | 2 | 2 | 2 | 2 |
Principaux différenciateurs
- Low-noise precision in a dual package (vs MC33078D)
- Precision-grade offset option in the same family (vs TS512AIDT)
- Wide single- and dual-supply operation (vs TS512IYDT)
Notes de conception
Place the supply-decoupling capacitor close to the SOIC-8 power pins, with the shortest practical ground return to the device. Keep sensitive input and feedback traces away from switching nodes, relay contacts, inductor pads, and high-current return paths. Use a continuous ground reference beneath the analog section when board space permits, and route both amplifier channels symmetrically when their signals must have matched delay or crosstalk behavior.
Do not treat the 3 MHz gain-bandwidth product as unlimited operating bandwidth. At gains approaching the amplifier's usable limits, noise gain, capacitive loading, and feedback topology can affect stability. Check the output-swing and common-mode limits at the selected supply voltage, especially in low-voltage single-supply circuits. Avoid operating an input near a rail unless the corresponding common-mode range explicitly permits it.
For low-level sensor signals, guard the input node and use a return path that does not share current with the amplifier output or digital switching circuitry. Estimate thermal noise from the source impedance, then compare it with the amplifier's 8 nV/√Hz input noise across the intended bandwidth. For capacitive sources, add an isolation resistor close to the input and verify stability with the complete cable, sensor, and filter network connected.
Choose the supply so the signal remains within both the input common-mode range and output swing. The device supports single supplies from 3 V to 30 V and dual supplies from ±1.5 V to ±15 V, but the usable signal range is narrower than the supply range. Keep power rails stable during startup and load transients, and verify that the chosen bypass network meets the stability requirements of the complete analog channel.
Informations de conformité
The technical material identifies the TS512 as a general-purpose precision dual operational amplifier and lists ESD protection of 2 kV. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated and are therefore recorded as unknown.