STMicroelectronics

TS512IDT - 3MHz Dual Precision Op Amp | STMicroelectronics

料号: TS512IDT ✓ 量产中
8 nV/√Hz Vdss 8-pin SOIC Package
最小起订量: 1 |

TS512IDT 概述

STMicroelectronics TS512IDT is a dual precision operational amplifier with a 3 MHz gain-bandwidth product, 8 nV/√Hz input-voltage noise density, and 0.03% distortion, housed in an 8-pin SOIC package. The TS512x family combines internally compensated low-noise operation with stable voltage-follower performance, making each amplifier suitable for precision signal conditioning and audio paths.

An operational amplifier, or op amp, is a high-gain differential amplifier that uses external feedback to set gain and filtering behavior. In the electronics hierarchy, the TS512IDT is a precision operational amplifier within the broader amplifier IC and analog signal-processing categories. Its two independent channels allow one package to process two signals, while internal frequency and phase compensation simplify voltage-follower and other high-gain configurations without external compensation components.

The principal features include 3 MHz gain-bandwidth product, 8 nV/√Hz noise density, 0.03% distortion, low power consumption, short-circuit protection, and high channel separation. Operation from a single 3 V to 30 V supply or from dual ±1.5 V to ±15 V rails gives designers flexibility across industrial, instrumentation, and signal-conditioning systems. The low-noise and low-distortion characteristics are particularly relevant when small sensor and audio signals must be amplified without adding substantial broadband noise or harmonic distortion.

Internally compensated architecture supports stable operation in voltage-follower configurations despite the amplifier's relatively high gain-bandwidth product. The TS512x family is designed for general-purpose precision applications where clean signal amplification matters more than very high speed. Two channels in one package reduce board-area requirements, while high channel separation helps maintain signal integrity when the channels process related low-level signals. The amplifier also includes ESD protection and a macromodel for circuit simulation.

Typical uses include audio preamplification, instrumentation-amplifier input stages, active filters, sensor signal conditioning, transducers, and general-purpose analog measurement chains. The 8-pin SOIC package is useful where conventional surface-mount assembly is required and the circuit operates across the stated -40°C to +125°C temperature range. The wide supply-voltage range also permits operation from industrial rails while retaining compatibility with lower-voltage analog systems.

Designers should verify input and output voltage limits, common-mode range, output-swing behavior, and stability against the exact load connected to each channel. Decoupling capacitors should be placed close to the supply pins, while sensitive-input routing should avoid nearby switching nodes and high-current return paths. The dual package does not require matched channels for general use, but input bias-current and offset behavior must be considered in precision DC measurements.

This page combines the TS512IDT's principal electrical characteristics with pin-compatible family alternatives, application guidance, comparison parameters, and practical circuit-design notes. These engineering-focused details help shorten component evaluation and support a more reliable transition from initial schematic design through PCB implementation and production qualification.

直接替换替代料: TS512IDT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: TS512IDT (相同外形与封装尺寸) ——差异在于 Gain-Bandwidth Product, Input Voltage Noise Density, Operating Temperature Range, Package.

Texas Instruments
Gain-Bandwidth Product: 15 MHz
Input Voltage Noise Density: 4.5 nV/√Hz
Operating Temperature Range: -40 °C to 85 °C
对比 TS512IDT →

TS512AIDT

✅ 直接替换
📦 8-pin SOIC
Same 3 MHz gain-bandwidth product and dual SOIC-8 format; the A-version maximum input offset voltage is 500 µV, while the exact TS512IDT offset difference is not stated in the cross-reference data.

📋 参考替代料(不在目录中)

TS512IYDT

✅ 直接替换
📦 8-pin SOIC
Same family architecture and 3 MHz gain-bandwidth product, giving 0% stated GBW difference; grade-suffix differences remain in temperature or qualification characteristics.

📋 参考替代料(不在目录中)

MC33078D

✅ 直接替换
Texas Instruments
📦 8-pin SOIC
2 circuits · 4.5 nV/√Hz · 15 MHz · 7 V/µs · Bipolar · 8-pin SOIC (D) · -40 °C to 85 °C · Audio and data-signal amplification

联系询价

查看数据手册 →

TS512IDT 最大额定值与电气特性

Amplifier Type Dual precision operational amplifier
Number of Circuits 2
Gain-Bandwidth Product 3 MHz
Input Voltage Noise Density 8 nV/√Hz
Distortion 0.03%
Single-Supply Operating Range 3 V to 30 V
Dual-Supply Operating Range ±1.5 V to ±15 V
工作温度范围 -40°C to +125°C
ESD Protection 2 kV
封装 8-pin SOIC
安装类型 Surface Mount
Compensation Internal frequency and phase compensation
Short-Circuit Protection Yes
Simulation Support Macromodel included

TS512IDT 8-pin soic 引脚配置指南

TS512IDT(8-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

TS512IDT 的 8-pin soic 封装引脚图

暂无详细引脚数据: TS512IDT.

请参阅 数据手册 以查看完整引脚配置。

典型应用

TS512IDT 适用于 6 应用s: Audio Preamplifier, Industrial Sensor Conditioning, Precision Active Filter, Instrumentation Measurement Front End, Data Acquisition Analog Front End, Portable Measurement Device.

🎧

Audio Preamplifier

The TS512IDT fits low-level audio preamplification because its 8 nV/√Hz input-voltage noise density supports small-signal amplification, while the 0.03% distortion specification limits added harmonic error. Place one channel in a gain stage and use the second channel for an active low-pass or output driver. The internally compensated amplifier operates stably as a voltage follower, which simplifies buffering after the gain-setting network. Keep input return paths short and use the highest practical gain in the first stage to minimize the contribution from the following stage.

🏭

Industrial Sensor Conditioning

The TS512IDT is appropriate for conditioning weak signals from resistive, piezoelectric, and low-level industrial sensors because its 8 nV/√Hz noise density supports low-noise amplification and its 3 MHz gain-bandwidth product covers moderate sensor bandwidths. The two channels can amplify a sensor input and provide an active filter or reference-buffer stage. Its single-supply operation from 3 V to 30 V allows integration near industrial rails. Grounding, shield routing, common-mode range, and output-swing limits remain the principal checks when the sensor environment introduces large transients or ground-potential differences.

📡

Precision Active Filter

The TS512IDT can implement a second-order active filter because each channel provides independent gain and filtering through external resistors and capacitors, while internal frequency and phase compensation supports stable voltage-follower use. Its 3 MHz gain-bandwidth product leaves useful bandwidth above audio and many control-signal ranges. The 0.03% distortion specification is valuable when filtering low-level analog information. Select resistor and capacitor tolerances according to the required cutoff accuracy, and verify phase margin with the actual load because passive tolerances and input capacitance can alter the intended response.

🔬

Instrumentation Measurement Front End

The TS512IDT suits instrumentation front ends that amplify small differential or single-ended measurement signals while preserving low noise and low distortion. One channel can provide gain, and the second can form a unity-gain buffer or active gain stage for a non-inverting topology. The broad 3 V to 30 V single-supply range supports multiple industrial configurations. Input bias current, offset voltage, common-mode range, and output settling behavior should be evaluated against the sensor impedance and required accuracy. High-impedance guarding around the input nodes can reduce leakage-induced error.

🖥️

Data Acquisition Analog Front End

The TS512IDT can provide the analog gain and buffering stage between a sensor and an ADC in a moderate-speed data-acquisition system. Its 3 MHz gain-bandwidth product is suitable for signals well below that bandwidth, while 8 nV/√Hz noise density and 0.03% distortion support accurate capture of small signals. The dual configuration can amplify and filter two channels or provide differential gain and common-mode handling. Select the gain so the ADC input range is not exceeded, then confirm the amplifier's output-swing limit and settling time against the sampling rate.

📱

Portable Measurement Device

The TS512IDT is useful in portable measurement equipment where low-noise amplification and compact dual-channel integration are important. The device can operate from a 3 V single supply, while its low-noise characteristics help preserve small measurement signals without introducing excessive broadband noise. Internal compensation simplifies follower-based filtering and buffering, reducing external component count. Battery-operated designs should still verify supply current, dropout behavior, shutdown strategy, and thermal rise for the selected operating voltage. Guard sensitive inputs against connector charge, display-switching noise, and charger transients.

What is the TS512IDT?
The TS512IDT is a dual precision operational amplifier from STMicroelectronics with a 3 MHz gain-bandwidth product, 8 nV/√Hz input-voltage noise density, and 0.03% distortion. It is packaged in an 8-pin SOIC and contains two independently usable amplifier channels. According to the STMicroelectronics TS512 product page, the TS512x devices use on-chip frequency and phase compensation for stable voltage-follower operation.
What are the key specifications of TS512IDT that engineers should know?
The TS512IDT combines two channels, a 3 MHz gain-bandwidth product, 8 nV/√Hz noise density, and 0.03% distortion in an 8-pin SOIC. According to the STMicroelectronics TS512 family information, it supports single supplies from 3 V to 30 V or dual supplies from ±1.5 V to ±15 V, includes internal compensation and short-circuit protection, and operates from -40°C to +125°C.
Where can I download the TS512IDT datasheet PDF?
The authoritative TS512IDT technical documentation is available from the STMicroelectronics TS512 product page at https://www.st.com/en/amplifiers-and-comparators/ts512.html. Select the datasheet link for the TS512 family to obtain the PDF. The manufacturer page is preferable to third-party copies because it reflects the latest controlled document and identifies the applicable grade, ordering information, electrical characteristics, and package drawings.
Where can I find the TS512IDT pinout?
The TS512IDT pin assignment is documented in the pinout and package-information section of the STMicroelectronics TS512 datasheet. The device uses an 8-pin SOIC with two complete operational-amplifier channels and shared supply connections. Before routing a PCB, verify every pin number against the current manufacturer pinout and confirm whether exposed-pad or thermal requirements apply to the specific ordering variant.
Is the TS512IDT suitable for audio preamplifier applications?
The TS512IDT is suitable for low-level audio preamplification because its 8 nV/√Hz noise density is suited to weak signals and its 0.03% distortion limit controls added harmonic error. According to the STMicroelectronics TS512 family information, the device also provides two channels in one 8-pin SOIC. The actual signal-to-noise ratio and distortion at the system output still depend on source impedance, gain, bandwidth, load, and supply voltage.
Can TS512IDT operate from a single 5 V supply?
Yes. The TS512IDT operates from a single supply of 3 V to 30 V, so a 5 V rail falls within its specified operating range. The STMicroelectronics TS512 family information also permits dual supplies from ±1.5 V to ±15 V. At low single-supply voltages, however, the selected output level must remain inside the device's output-swing and input common-mode limits.
How does TS512IDT compare with TS512AIDT?
The TS512AIDT is a closely related TS512-family dual amplifier in the same SOIC-8 format, while the TS512IDT is the standard grade. Cross-reference information identifies a maximum input offset voltage of 500 µV for the A version and lists a 3 MHz gain-bandwidth product for the family. Choose TS512AIDT when its tighter offset specification is required; otherwise verify the complete electrical tables before treating it as a drop-in replacement.
TS512IDT vs TS512IYDT - which is better for an industrial amplifier?
TS512IDT and TS512IYDT are members of the same TS512 dual-amplifier family, and the comparison data lists a 3 MHz gain-bandwidth product, 3 V to 30 V single-supply range, and low-noise, low-distortion operation. The suffix indicates different grade or qualification characteristics, so the best choice depends on temperature coverage, qualification, and ordering requirements. Review the STMicroelectronics ordering table for the exact suffix assigned to each application.
When should I choose the TS512IDT over another dual precision op amp?
Choose the TS512IDT when a design needs two channels, 3 MHz gain-bandwidth product, 8 nV/√Hz noise density, low distortion, and operation from a single 3 V to 30 V supply or dual ±1.5 V to ±15 V rails. It is particularly suitable for precision signal conditioning and audio stages that do not require very high speed. Select another part instead if its wider bandwidth, rail-to-rail input/output, lower offset, or lower power consumption is essential.
Is TS512IDT suitable for sensor signal conditioning?
The TS512IDT is well suited to low-level sensor signal conditioning because its 8 nV/√Hz noise density and 0.03% distortion specification support accurate amplification of small signals. The two channels can process related sensor outputs or form an active-filter stage. According to the STMicroelectronics TS512 family information, internal compensation supports stable voltage-follower configurations. Sensor excitation, grounding, filtering, and common-mode limits still require separate design verification.
What can replace the TS512IDT?
The TS512AIDT and TS512IYDT are the closest same-family drop-in candidates identified for the TS512IDT because they use the dual SOIC-8 architecture and retain the 3 MHz gain-bandwidth product. MC33078D also appears in a direct three-way comparison as a competing dual amplifier. A valid replacement must still match pinout, supply range, input common-mode limits, output swing, offset, bias current, noise, stability, and temperature grade.
What is the best STMicroelectronics equivalent for TS512IDT?
The best same-manufacturer equivalent depends on the grade requirement: TS512AIDT provides a precision-grade option with a listed maximum input offset voltage of 500 µV, while TS512IYDT is a related TS512 family variant for applications governed by a different grade designation. Both use the SOIC-8 dual-amplifier format identified in the cross-reference material. Validate the complete ordering table and pin descriptions before releasing a substitution.
Can TS512IDT be used as a voltage follower?
Yes. The TS512x family includes internal frequency and phase compensation, allowing stable operation in voltage-follower configuration despite its 3 MHz gain-bandwidth product. According to the STMicroelectronics TS512 product page, this internal compensation is a defining family feature. Output loading, input common-mode voltage, output swing, and capacitive-load stability should still be checked against the electrical characteristics for the selected supply.
Where can I buy TS512IDT online and what is the lead time?
Use the Request a Quote form on this page to ask for TS512IDT pricing, current stock, order quantities, and lead time. The form routes the request for a current commercial response without embedding a price that may quickly become stale. For design planning, also confirm the required SOIC-8 order code, manufacturer lifecycle status, and delivery schedule before committing the component to a production release.
What is the price and stock status of TS512IDT?
Current TS512IDT price and stock status should be requested through the Request a Quote form on this page. Commercial availability can vary with order quantity, package form, and market conditions, while a static price figure would age quickly. Include the required quantity, target delivery date, and whether reels, cut tape, or another permitted packing format is needed so the quotation can reflect the actual production requirement.

工程参考数据: TS512IDT ——对比、设计指导和合规信息。

选型指南

Choose the TS512IDT when the design needs two low-noise precision amplifier channels, 8 nV/√Hz input noise density, 0.03% distortion, internal compensation, and operation from a 3 V to 30 V single supply or ±1.5 V to ±15 V dual rails. It is a strong fit for audio preamplification, precision active filters, instrumentation, and moderate-speed data-acquisition front ends. Choose TS512AIDT when the application specifically benefits from its listed 500 µV maximum offset for the A version. Consider TS512IYDT when its grade designation matches the required temperature or qualification conditions. MC33078D is a cross-brand candidate, but select it only after its offset, bias current, noise, common-mode range, output swing, slew rate, and stability data have been compared with the TS512IDT.

与替代料对比

参数 本产品 TS512AIDT TS512IYDT MC33078D
Package 8-pin SOIC 8-pin SOIC - same package 8-pin SOIC - same package 8-pin SOIC - same package
Brand STMicroelectronics STMicroelectronics STMicroelectronics Motorola
Number of Amplifier Channels 2 2 2 2

关键差异点

  • Low-noise precision in a dual package (对比 MC33078D)
  • Precision-grade offset option in the same family (对比 TS512AIDT)
  • Wide single- and dual-supply operation (对比 TS512IYDT)

设计说明

Place the supply-decoupling capacitor close to the SOIC-8 power pins, with the shortest practical ground return to the device. Keep sensitive input and feedback traces away from switching nodes, relay contacts, inductor pads, and high-current return paths. Use a continuous ground reference beneath the analog section when board space permits, and route both amplifier channels symmetrically when their signals must have matched delay or crosstalk behavior.

Do not treat the 3 MHz gain-bandwidth product as unlimited operating bandwidth. At gains approaching the amplifier's usable limits, noise gain, capacitive loading, and feedback topology can affect stability. Check the output-swing and common-mode limits at the selected supply voltage, especially in low-voltage single-supply circuits. Avoid operating an input near a rail unless the corresponding common-mode range explicitly permits it.

For low-level sensor signals, guard the input node and use a return path that does not share current with the amplifier output or digital switching circuitry. Estimate thermal noise from the source impedance, then compare it with the amplifier's 8 nV/√Hz input noise across the intended bandwidth. For capacitive sources, add an isolation resistor close to the input and verify stability with the complete cable, sensor, and filter network connected.

Choose the supply so the signal remains within both the input common-mode range and output swing. The device supports single supplies from 3 V to 30 V and dual supplies from ±1.5 V to ±15 V, but the usable signal range is narrower than the supply range. Keep power rails stable during startup and load transients, and verify that the chosen bypass network meets the stability requirements of the complete analog channel.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The technical material identifies the TS512 as a general-purpose precision dual operational amplifier and lists ESD protection of 2 kV. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated and are therefore recorded as unknown.

数据核验日期: 2026-11-10 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

TS512IDT datasheet TS512IDT specifications TS512IDT pinout TS512IDT datasheet pdf TS512IDT equivalent TS512IDT replacement TS512IDT vs TS512AIDT TS512IDT vs TS512IYDT TS512IDT vs MC33078D TS512IDT SOIC-8 footprint TS512IDT audio preamplifier TS512IDT sensor signal conditioning STMicroelectronics TS512IDT TS512IDT price TS512IDT stock

相关元器件 & 术语

STMicroelectronics TS512IDT TS512AIDT TS512IYDT MC33078D precision operational amplifier dual op amp amplifier IC analog signal conditioning gain-bandwidth product input-voltage noise density low distortion voltage follower active filter audio preamplifier sensor signal conditioning data-acquisition front end 8-pin SOIC SOIC package surface-mount package single-supply operation dual-supply operation internal compensation short-circuit protection ESD protection
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情