VSC7422XJQ-04 - 25-Port Gigabit Ethernet Switch | Microchip
Référence : VSC7422XJQ-04 ✓ ActifVSC7422XJQ-04 Présentation
An Ethernet switch is a Layer 2 network device that receives Ethernet frames on one port, examines the destination MAC address, and forwards traffic through the appropriate output port. A managed Layer 2 switch adds configuration, monitoring, and traffic-control functions that a basic unmanaged switch does not provide. The VSC7422 combines switching and copper physical-layer functions, allowing twelve copper links to share the same switching silicon while additional interfaces connect the device to upstream processors, PHYs, or network equipment.
According to the Microchip VSC7422 product page, the device is the industry's first fully integrated 25-port Gigabit Ethernet switch with 12 copper PHYs in one package. That integration is the defining feature: designers can use one switching IC for twelve copper ports and connect additional ports through external PHYs. Microchip also identifies the VSC8512 as a companion 12-port PHY, enabling a 25-port copper design with only two main ICs when that companion device is used for the remaining interfaces.
The VSC7422XJQ-04 is identified in distributor listings as a telecom Ethernet switch with a 302-TQFP package. The large lead count accommodates the integrated copper interfaces, control signals, power rails, and management connectivity in a single surface-mount device. Its footprint is materially larger than a typical low-port Ethernet controller, so PCB area, via density, thermal performance, and assembly capability should be considered before layout begins.
Typical deployments include telecom access equipment, industrial Ethernet gateways, network appliances, and managed copper switching platforms. The integrated copper PHYs reduce board-level PHY count, while the Layer 2 switching function consolidates multiple Ethernet links around a single control point. Compared with a board assembled from discrete switching and PHY devices, the integrated approach can shorten copper routing, simplify assembly, and reduce component-inventory complexity.
Design the power and thermal plan around the full 302-pin footprint rather than a small Ethernet controller land pattern. Follow the manufacturer layout guidance for high-speed copper pairs, provide clean supply rails and local decoupling, and validate the magnetics and connector interface for the target cable length and isolation requirements. Use the pin-description table and recommended schematic in the manufacturer datasheet when assigning every signal and supplying the exposed thermal and power connections.
This page consolidates the manufacturer architecture description, distributor package identification, drop-in replacement information, and board-level design guidance into one engineering-focused reference for the VSC7422XJQ-04.
Alternatives de remplacement direct pour VSC7422XJQ-04 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec VSC7422XJQ-04 (même facteur de forme et même empreinte) — différant par Integrated Copper PHYs, Mounting Type, Package, Total Ports.
VSC7422XJG-04
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →VSC7422XJQ-04 Valeurs maximales et caractéristiques électriques
| Device Type | Telecom Ethernet switch |
| Switching Layer | Layer 2 |
| Total Ports | 25 ports |
| Integrated Copper PHYs | 12 ports |
| Copper Interface Rate | 10/100/1000Base-T |
| Ethernet Standard | Gigabit Ethernet |
| Boîtier | 302-TQFP, 24 x 24 mm |
| Type de montage | Surface mount |
| Lead Count | 302 leads |
| Statut RoHS | RoHS |
| Managed Switching | Managed L2 switch |
| Companion PHY | Microchip VSC8512 12-port copper PHY |
| Two-IC 25-Port Design Support | Yes |
| Integrated PHY Count | 12 copper PHYs |
| Maximum Ethernet Port Speed | 1 Gb/s |
Guide de configuration des broches du VSC7422XJQ-04 302-tqfp, 24 x 24 mm
Configuration des broches du VSC7422XJQ-04 (boîtier 302-tqfp, 24 x 24 mm). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour VSC7422XJQ-04.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
VSC7422XJQ-04 convient pour 6 applications: Telecom Access and Aggregation Equipment, Industrial Ethernet Gateway, Managed Network Appliance, Industrial Network Switch Platform, Multi-Port PoE Network Equipment, Carrier Ethernet Edge Device.
Telecom Access and Aggregation Equipment
The VSC7422XJQ-04 fits telecom access equipment that must consolidate multiple copper Ethernet services into a compact Layer 2 switching platform. Its 25-port architecture and 12 integrated copper PHYs reduce the number of external PHY devices needed beside the main switch. The 302-TQFP package still requires deliberate plane allocation and thermal planning because the switching and copper-interface functions are concentrated in one 24 x 24 mm device. Use the manufacturer reference layout for high-speed pair routing, grounding, and power decoupling.
Recommandé
Industrial Ethernet Gateway
The VSC7422XJQ-04 is suitable for an industrial Ethernet gateway that combines numerous copper ports with centralized Layer 2 forwarding. Twelve integrated PHYs shorten the path from connector magnetics to the switching fabric and can reduce board component count compared with a design built from separate PHY packages. For industrial equipment, verify the exact temperature grade and isolation design for the target enclosure. Follow the manufacturer layout guidance to keep copper links away from noisy switching and power-return paths.
Recommandé
Managed Network Appliance
The VSC7422XJQ-04 supports high-port-count network appliances where an embedded controller must connect to multiple copper-facing line cards or service ports. Its managed Layer 2 switch handles frame forwarding while twelve integrated PHYs provide direct copper connectivity, allowing fewer switching and PHY devices to occupy the chassis controller. The large 302-TQFP footprint must be planned alongside processor, memory, and power circuitry. Use the manufacturer's recommended schematic and reference layout rather than treating the device as a small two-port Ethernet controller.
Recommandé
Industrial Network Switch Platform
The VSC7422XJQ-04 is a strong fit for an industrial Layer 2 switch platform requiring twelve immediately available copper ports and additional switched connectivity. Integrating the PHYs with the switch reduces board-level interconnect density and repetitive analog-interface routing, but the single 302-TQFP package also concentrates heat across a large die area. Provide multiple power planes, local high-frequency decoupling, and copper thermal area according to the manufacturer layout. Validate conducted emissions and thermal rise in the final enclosure rather than on an isolated laboratory board.
Recommandé
Multi-Port PoE Network Equipment
The VSC7422XJQ-04 can serve as the central Layer 2 switching device in multi-port network equipment that adds powered Ethernet capability through downstream power-management circuitry. The switch provides twelve integrated copper PHYs for direct endpoint connections, while additional switched interfaces remain available through external PHYs. Keep high-current power-conversion stages and magnetics physically separated from sensitive copper pairs, and follow the manufacturer recommendations for switching-node return currents. Confirm PoE voltage, current, isolation, and thermal requirements at the complete system level.
Recommandé
Carrier Ethernet Edge Device
The VSC7422XJQ-04 matches carrier-edge equipment that needs numerous 10/100/1000Base-T service connections managed through a Layer 2 switch. Its 25-port structure supports dense copper aggregation, and the 12 integrated PHYs reduce the number of external devices compared with a modular switch design. Confirm telecom-grade temperature and qualification requirements for the exact ordering suffix before release. Follow the reference layout for differential pair geometry, return paths, and clock distribution to preserve signal integrity across all copper ports.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour VSC7422XJQ-04 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | VSC7422XJG-04 |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 302-TQFP (24 x 24 mm) | 302-TQFP (24 x 24 mm) |
| Device Type | Telecom Ethernet switch | Ethernet IC, L2 switch |
| Total Ports | 25 ports | 25 ports |
| Integrated Copper PHYs | 12 ports | 12 ports |
| Switching Layer | Layer 2 | Layer 2 |
| Maximum Copper Link Rate | 1 Gb/s | 1 Gb/s |
| Copper Interface Type | 10/100/1000Base-T | 10/100/1000Base-T |
Principaux différenciateurs
- Twelve copper PHYs integrated with the switching fabric (vs VSC7422XJG-04)
- Telecom-oriented ordering variant (vs VSC7422XJG-04)
- High integration in one 302-TQFP package (vs Discrete switching and PHY implementation)
- Two-IC path to a 25-port copper design (vs Multi-PHY discrete implementation)
Notes de conception
Use the manufacturer reference layout for the 302-TQFP footprint and place input and output decoupling directly at the associated power and ground pins. Because the device combines 12 copper PHYs with switching logic, preserve the recommended partitioning between copper-interface and high-speed digital return paths. Do not substitute a generic 302-pin CAD symbol without verifying the exposed thermal and power lands against the mechanical drawing.
Route each copper interface as a controlled-impedance differential pair with continuous reference planes and avoid crossing plane splits. Keep connector and magnetics interfaces away from clocks, switching-node currents, and regulator switching nodes. Apply the manufacturer’s recommended pair geometry, via stitching, and isolation spacing; these details determine link margin more effectively than component substitution at the same nominal Gigabit Ethernet rate.
Estimate junction temperature from total package dissipation, the board-dependent junction-to-ambient value, and the enclosure’s heat-transfer path. The large 302-TQFP footprint provides substantial lead area for power delivery but concentrates active circuitry in one package. Spread heat through multilayer copper where the mechanical design allows, keep the area beneath the device free of obstructing thermal features, and verify the hottest operating corner in the final enclosure.
Do not treat VSC7422XJG-04 as an automatic substitute without checking the ordering-code differences. The documented alternative retains the 25-port, 12-copper-PHY architecture and 302-TQFP format, but it is identified as the industrial-temperature version. Before substitution, compare the complete pin description, electrical limits, temperature range, lifecycle status, firmware support, and qualification requirements in the manufacturer documentation.
Informations de conformité
JLCPCB identifies the VSC7422XJQ-04 as RoHS. No AEC-Q100, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for this ordering code.