Z86E2116FSC - 16MHz 8KB OTP 8-Bit MCU | Zilog
Référence : Z86E2116FSC ✓ ActifZ86E2116FSC Présentation
An 8-bit microcontroller is a microprocessor optimized for embedded control tasks such as reading sensors, operating relays, driving displays, and managing communication peripherals. The Z86E2116FSC belongs to the Z8 family of CMOS application-specific controllers, where the CPU, memory, timers, I/O, and communication functions are integrated into one device. Its 8 KB OTP program memory supports a fixed application program, while its 16 MHz operating speed provides the timing required for common control-loop and serial-interface tasks.
The principal features include an 8-bit processor core, 8 KB OTP program memory, 16 MHz clock operation, UART support, and a 44-pin QFP package. The UART allows the controller to exchange formatted serial data with sensors, programmers, modules, or supervisory electronics. OTP memory also gives a production design a stable, programmed configuration without an external writable program-memory component.
Technical selection should focus on whether the required peripherals, voltage range, clock configuration, and interrupt architecture are sufficient for the target design. Because firmware is permanently programmed after device programming, prototype changes require a different programmed MCU rather than a routine field update. Engineers should also verify oscillator, reset, I/O, and serial-interface requirements against the manufacturer datasheet before schematic capture.
Typical uses include compact appliance controllers, serial-interface modules, keypad and display products, industrial control boards, and embedded peripheral control. In these systems, the MCU can supervise inputs, execute control logic, and manage UART communication while keeping the footprint within a 44-pin surface-mount package.
PCB design should preserve access to every programming and test signal, maintain adequate copper around ground and power pins, and follow the datasheet's recommended decoupling layout. Because OTP programming is a one-time manufacturing operation, production traceability and device marking should be designed into the process, while firmware changes should be accommodated by maintaining a replaceable MCU footprint.
This product page consolidates the confirmed 8-bit, 16 MHz, 8 KB OTP, UART, and 44-QFP characteristics with package guidance, sourcing information, design notes, and a qualified comparison framework. It is intended to help engineers verify functionality and manufacturing readiness without treating a family member as a drop-in substitute without further engineering review.
Alternatives de remplacement direct pour Z86E2116FSC — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec Z86E2116FSC (même facteur de forme et même empreinte) — différant par RoHS Status, Terminal Form.
Z86E2116VSC
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →Z86E2116FSC Valeurs maximales et caractéristiques électriques
| Device Type | 8-bit CMOS OTP microcontroller |
| Series | Z8 |
| Maximum CPU Clock | 16 MHz |
| Program Memory | 8 KB OTP |
| Program Memory Organization | 8K x 8 bits |
| Serial Interface | UART |
| Boîtier | 44-pin QFP |
| Package Code | QFP |
| Terminal Count | 44 terminals |
| Package Shape | Square |
| Terminal Form | Gull wing |
| Temperature Grade | Commercial |
| Type de montage | Surface mount |
| Statut RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Guide de configuration des broches du Z86E2116FSC square
Configuration des broches du Z86E2116FSC (boîtier square). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour Z86E2116FSC.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
Z86E2116FSC convient pour 6 applications: Appliance Control Boards, UART-Based Peripheral Modules, Industrial Interface Controllers, Keypad and Display Products, Sensor Interface Modules, Embedded Peripheral Control.
Appliance Control Boards
The Z86E2116FSC fits compact appliance controllers that require permanent control firmware, digital I/O, and a serial diagnostic channel. Its 16 MHz 8-bit CPU provides timing for control tasks, while 8 KB of OTP program memory supports a finalized operating program. In a typical product, the MCU scans buttons or sensors, manages relays and indicators, and uses the UART for service diagnostics or an external display. The 44-pin QFP keeps lead spacing compatible with conventional surface-mount assembly. Before release, confirm the complete pin map, clock requirements, and electrical operating range in the manufacturer datasheet.
UART-Based Peripheral Modules
The Z86E2116FSC is appropriate for a small embedded peripheral that exchanges commands or status data through a UART. Its integrated serial capability avoids a separate communication controller, and the 16 MHz operating rate supports responsive handling of framed data and local I/O. A module could use the MCU to interpret host commands, operate an actuator, and return status. Because OTP memory is not field-rewritable, the design should reserve programming and manufacturing-test access before production. According to the manufacturer datasheet, UART clocking, baud-rate configuration, and signal levels must be matched to the system interface.
Industrial Interface Controllers
The Z86E2116FSC can serve as the local controller in a compact industrial interface that accepts digital commands and reports state over UART. The 8-bit architecture and 16 MHz clock are suitable for deterministic supervisory functions such as input debouncing, output sequencing, and status-word generation. Its 8 KB OTP program memory favors a fixed, relatively compact control function rather than a large protocol stack. System integrators should verify the operating-temperature range, supply voltage, and I/O ratings in the manufacturer datasheet. They should also reserve programming contacts because the MCU's OTP program memory cannot be revised after programming.
Keypad and Display Products
The Z86E2116FSC fits keypad, menu, and small display controllers where a dedicated low-cost MCU must scan inputs and manage an interface. The 16 MHz clock provides sufficient execution rate for contact scanning, display updates, and communication tasks, while the integrated UART can connect to a host or display controller. Eight kilobytes of OTP memory is appropriate for a compact, stable interface program rather than a feature-rich graphical application. During schematic design, consult the manufacturer pin-description table for multiplexed I/O and display connections. Validate timing and bus-direction requirements because package compatibility alone does not establish complete peripheral compatibility.
Sensor Interface Modules
The Z86E2116FSC can coordinate a small sensor module that samples digital inputs, evaluates control thresholds, and reports measurements through a serial link. The UART supports communication with a sensor, host processor, or configuration tool, while the 16 MHz 8-bit core handles protocol and control tasks. The 8 KB OTP capacity is well suited to a focused measurement-control program that does not require in-field firmware updates. According to the manufacturer datasheet, confirm the available I/O count, ADC availability, oscillator arrangement, and electrical limits before assigning sensor signals. Preserve access to the programming interface so each device can be configured during manufacturing.
Embedded Peripheral Control
The Z86E2116FSC is useful in compact auxiliary controllers that coordinate relays, indicators, and a host serial port. Its 16 MHz 8-bit processor can execute a fixed sequence of control actions, and the UART permits command exchange with a primary controller. The 44-pin QFP provides a conventional surface-mount option with accessible leads for inspection and rework. Engineers should confirm that every required peripheral, interrupt source, and I/O function appears in the manufacturer datasheet. If the application requires field-updatable firmware, choose a controller with rewritable program memory rather than using the Z86E2116FSC's one-time-programmable architecture.
Données de référence d'ingénierie pour Z86E2116FSC — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | Z86E2116VSC |
|---|---|---|
| Brand | Zilog | Zilog |
| Package | 44-pin QFP | 44-pin QFP |
| CPU Architecture | 8-bit | 8-bit |
| Maximum CPU Clock | 16 MHz | 16 MHz |
| Program Memory | 8 KB OTP | 8 KB OTP |
| Program Memory Organization | 8K x 8 bits | 8K x 8 bits |
Principaux différenciateurs
- Integrated UART in an 8 KB OTP MCU (vs Z86E2116VSC)
- Production-oriented one-time-programmable memory (vs Z86E2116VSC)
- 16 MHz processing rate in a compact controller (vs Z86E2116VSC)
Notes de conception
Use the manufacturer pin-description table and package drawing to create the 44-pin QFP land pattern. Confirm body size, lead pitch, pin numbering, and any exposed thermal-pad requirement before Gerber release. Place the oscillator, decoupling capacitors, programming contacts, and UART interface components close to their associated pins to minimize trace length, ringing, and susceptibility to external noise.
Do not plan to update application firmware after OTP programming. Maintain a controlled programming and traceability process that records the approved firmware revision for each MCU. Prototype changes must be implemented in a separately programmed device, and production fixtures should verify program identity without disturbing adjacent signals. A PCB change that adds programming access can reduce redesign risk.
Route the UART lines away from switching nodes and noisy clock or relay-control traces. Provide a common, low-impedance ground system and place supply bypass capacitors according to the manufacturer reference layout. If the MCU controls relays, motors, or high-current outputs, keep those paths separate from sensitive serial and timing signals, and account for ground bounce and supply transients.
Determine the operating voltage and current requirements from the manufacturer datasheet before selecting the board power source. The 16 MHz clock rating does not by itself define the permitted voltage range or current consumption. Validate startup, reset, brownout behavior, and maximum peripheral loading across the intended supply conditions so the power tree remains stable during reset and peripheral activation.
Informations de conformité
The device is an 8-bit embedded microcontroller, so AEC-Q100 automotive qualification is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the product records and remain unknown.