מוצרים (44,000+)

PCA82C251T - 24V CAN Transceiver, 1MBd, SOIC-8 | NXP
PCA82C251T

PCA82C251T - 24V CAN Transceiver, 1MBd, SOIC-8 | NXP

The NXP PCA82C251T is a legacy CAN (Controller Area Network) bus transceiver that serves as the physical interface between a CAN protocol controller and the differential CAN bus, operating at data rates up to 1 MBd in 24V automotive and industrial systems. Housed in an 8-pin SOIC (SO-8) surface-mount package, it provides differential transmit capability to the bus and differential receive capability to the CAN controller, with full conformance to the ISO 11898-24V standard for 24V systems used in trucks, buses, and heavy industrial vehicles. A CAN transceiver is a physical-layer (PHY) device that converts the single-ended digital transmit (TXD) and receive (RXD) signals from a CAN protocol controller into the differential dominant/recessive signaling required by the CAN bus. It sits between the protocol controller (an MCU with a CAN module) and the twisted-pair bus, providing the drive strength, common-mode rejection, and bus-fault protection needed for robust communication. The PCA82C251 belongs to the broader family of CAN transceivers and is part of the NXP (formerly Philips Semiconductors) automotive connectivity portfolio. Key features of the PCA82C251T include a maximum data rate of 1 MBd, wide supply voltage range of 4.5V to 5.5V (typical 5V), bus terminals tolerant to -27V to +40V transients, low current consumption in standby and recessive states, thermal shutdown protection, and current limiting on the bus outputs. The device operates over the -40C to +125C automotive temperature range, making it suitable for under-hood applications and other harsh industrial environments. It is supplied in the industry-standard 8-pin SOIC (SO-8) package for reflow-soldered surface-mount assembly. The PCA82C251T uses a bipolar CMOS process with on-chip bus-driver protection and slope-control circuitry to limit RFI emissions. Its high-impedance bus input during supply loss prevents the device from loading the bus when unpowered, supporting multi-node hot-swap scenarios. Compared to lower-voltage CAN transceivers, the 24V-tolerant bus pins make this part specifically suited for trucks, buses, agricultural machinery, and industrial CAN networks powered from 24V rails where common-mode transients exceed the range of 12V-only parts. Typical applications include 24V truck and bus CAN networks, agricultural and construction equipment CAN buses, industrial automation CANopen networks, forklift and material-handling vehicle communication, and CAN-based battery management in 24V lead-acid battery stacks. The ISO 11898-24V conformance also makes it a candidate for heavy-duty on-road and off-road vehicle communication backbones. When designing with the PCA82C251T, note that it is a legacy part and the modern TJA1051T, TJA1042T, or TJA1057T from NXP offer lower quiescent current, faster loop times, and improved EMC behavior for new designs. Engineers should select a 24V-rated replacement only when pin-compatibility or bus-fault tolerance is critical; the standard 12V TJA1050T is NOT a drop-in because its bus common-mode range is narrower and will not survive 24V-system transients. This page synthesizes distributor pricing, verified drop-in alternatives (same-brand and cross-brand in SOIC-8), practical design notes, and a parameter comparison table not bundled together on the manufacturer's product page.

RFQ צור קשר
PCA82C251T-YM118 - 24V CAN Transceiver, 1Mbps, SOIC-8 | NXP
PCA82C251T-YM118

PCA82C251T-YM118 - 24V CAN Transceiver, 1Mbps, SOIC-8 | NXP

The NXP PCA82C251T-YM118 is a legacy CAN bus transceiver for 24 V systems, providing the physical interface between a CAN protocol controller and the differential CAN bus. Housed in an 8-pin SO (SOIC-8) surface-mount package, it supports data rates up to 1 Mbps and operates from a single 5 V supply (4.5 V to 5.5 V), with bus pins tolerant to ±27 V of common-mode voltage for harsh 24 V automotive and industrial environments. A CAN transceiver (Controller Area Network transceiver) is a physical-layer device that converts the digital transmit/receive logic of a CAN protocol controller into the differential voltage signaling required by the CAN bus standard (ISO 11898). Within the broader system hierarchy, a CAN transceiver sits between the protocol controller (MCU) and the physical wiring harness, and belongs to the family of differential line drivers / interface ICs / wired-connectivity semiconductors. The 82C251 is the third-generation "PCA82C251" device, designed for 24 V truck and bus applications and predates the modern TJA1050 / TJA1042 / TJA1051 family. Key features include ±27 V bus fault protection on CANH and CANL, thermal shutdown with automatic recovery, a current-limited transmitter for short-circuit protection on the bus, and a low-current standby mode (typ. 275 µA supply current per Mouser listing). The differential receiver provides high common-mode rejection, and the driver stage supports slew-rate-limited transmission at speeds up to 1 Mbaud. The device exposes TxD, RxD, VCC, GND, CANH, CANL, Vref, and Rs pins on the SO-8 footprint. The architecture uses a bipolar process optimized for high bus voltage tolerance, with on-chip protection diodes clamping transient voltages beyond the supply rails. The Rs pin selects between high-speed, slope-control, and standby modes, providing a software/hardware mechanism for EMC tuning or low-power operation when the bus is idle. Typical applications include 24 V truck and bus CAN nodes, industrial CANopen networks, automotive body and chassis ECUs, agricultural machinery telemetry, and marine electronics. It is a pin-compatible second-source for the legacy PCA82C251 footprint, useful when modern 12 V TJA parts are not suitable. When designing with this part, place a 100 nF decoupling capacitor close to the VCC pin and use a split termination (60 Ω + 60 Ω + 100 nF to ground) at each end of the CAN bus for proper 24 V signal integrity. The Rs pin mode selection must be configured via a resistor to ground or to VCC; leaving it floating is not recommended. The PCA82C251T is marked NRND by NXP - prefer the TJA1051T or TJA1057T for new designs, but this part remains in production for legacy 24 V applications. This page synthesizes distributor stock, parametric data, drop-in second sources, and application guidance drawn from NXP's PCA82C251 datasheet plus current distributor inventory, not all of which appears in a single manufacturer PDF.

RFQ צור קשר
PCA82C251T/N3,118 - 24V CAN Transceiver SOIC-8 | NXP
PCA82C251T-N3118

PCA82C251T/N3,118 - 24V CAN Transceiver SOIC-8 | NXP

The NXP PCA82C251T/N3,118 is the interface between a CAN protocol controller and the physical bus, primarily intended for applications up to 1 MBaud in 24 V truck and bus systems. It provides differential transmit capability to the bus and differential receive capability to the CAN controller and is fully compatible with the ISO 11898-24 V standard. The /N3,118 suffix denotes the SOIC-8 (D-package) tape-and-reel delivery option used for high-volume automated assembly. A CAN transceiver (Controller Area Network transceiver) is a physical-layer IC that converts the digital transmit (TXD) and receive (RXD) signals of a CAN protocol controller into the differential CANH and CANL bus signals, and vice versa. Within the broader hierarchy, a CAN transceiver is a type of bus transceiver, which is a type of interface IC, which sits inside the Interface ICs category of integrated circuits. The PCA82C251 family targets 24 V automotive and industrial systems where high bus robustness and good electromagnetic compatibility are required. Key features include a -27 V to +40 V bus fault tolerance on CANH/CANL, thermal shutdown protection, current limiting on the transmitter outputs, and a slope-control pin that lets the user programme the bus rise/fall time. The IC operates from a single 4.5 V to 5.5 V supply, draws a typical quiescent current of 16 mA in recessive mode, and survives automotive transients on the bus lines. The SOIC-8 plastic package offers a small PCB footprint with a standard 1.27 mm pin pitch. Typical applications include 24 V truck and bus CAN nodes, industrial CANopen networks, agricultural and construction machinery, and any 12 V or 24 V CAN bus node requiring the classic PCA82C251 silicon. The PCA82C251 is the second-generation PCA82C250 follow-on and is widely second-sourced across the industry. Note that NXP has moved this part to NRND (Not Recommended for New Designs) - new designs should evaluate TJA1043, TJA1051, or TJA1042 for similar 24 V capability. When designing with this part, place a 100 nF decoupling capacitor as close as possible to pin 8 (VCC) and follow the ISO 11898 bus termination of 120 Ω at each end of the bus. The slope-control resistor on pin 8 (Rs) must be chosen against the desired bit rate; for 1 MBaud operation NXP recommends tying Rs to ground, while for lower bit rates a larger resistor reduces EMI. This page synthesises distributor stock, drop-in equivalents, and design guidance not found in the standalone datasheet PDF.

RFQ צור קשר
PCA82C251T/YM,112 - CAN Transceiver for 24V Systems | NXP
PCA82C251T-YM112

PCA82C251T/YM,112 - CAN Transceiver for 24V Systems | NXP

The NXP Semiconductors PCA82C251T/YM,112 is a legacy Controller Area Network (CAN) transceiver for 24 V systems, supplied in an 8-pin SOIC package (SOT96-1 / SO-8). The device provides a single differential transmit driver and a single differential receiver, providing the physical interface between a CAN protocol controller and the differential CAN bus. It operates from a single 4.5 V to 5.5 V supply, supports data rates up to 1 Mbaud, and is fully compatible with the ISO 11898-24 V standard. What is a CAN transceiver? A CAN transceiver (Controller Area Network transceiver) is a physical-layer interface IC that bridges a digital CAN protocol controller — typically a microcontroller with a built-in CAN module — and the differential CAN bus wiring found in vehicles, industrial equipment, and factory automation systems. Within the broader semiconductor hierarchy, a CAN transceiver belongs to the Interface ICs family, which sits inside the Integrated Circuits product tree. It is the companion IC to a CAN controller, the safety/transceiver side of an automotive/industrial bus, providing the differential drive strength, common-mode tolerance, and bus-fault robustness that digital logic alone cannot deliver. Key features of the PCA82C251T/YM,112 include slope-control to reduce Radio Frequency Interference (RFI), thermal shutdown protection, short-circuit protection on the bus pins, and an exposed thermal pad-friendly SO-8 footprint. The transceiver provides recessive and dominant bus states compliant with ISO 11898-24 V, can detect a permanent dominant condition on the bus, and includes a low-current standby mode controlled via the Rs (slope / standby) pin. The bus pins (CANH, CANL) survive load-dump transients encountered in 12 V and 24 V automotive/industrial environments, making the part the workhorse interface for truck, bus, agricultural, and off-road vehicle networks. Internally, the PCA82C251T/YM,112 uses a bipolar transmitter architecture with a precision differential output stage. The slope-control pin (pin 8) lets the designer trade edge rate against RFI; slower edges reduce emissions on unshielded bus cabling at the cost of maximum achievable bit rate. The receiver compares the bus differential voltage against an internal reference with sufficient hysteresis to reject common-mode noise, and the TXD input feeds a dominant/recessive driver that pulls the bus to the ISO 11898-24 V defined levels. A thermal shutdown block protects the output stage against continuous short circuits on CANH or CANL. Typical applications include in-vehicle CAN networks for trucks, buses and agricultural machinery, industrial automation CAN nodes, building automation (HVAC, lifts), and any 24 V battery-powered CAN segment requiring compliance with ISO 11898-24 V. Designers pair the PCA82C251T/YM,112 with microcontrollers that include a CAN controller (such as NXP LPC, S32K, or Kinetis families) and external protection components (TVS diodes, common-mode chokes) on the bus side. When designing with this transceiver, fit a split-termination network (typically 60 Ω total with a 10 nF to 100 nF capacitor to ground) close to the bus pins to match the cable impedance and improve EMC. Slope-control resistance should be chosen to keep edge times short enough for the target baud rate while still meeting automotive EMC limits. Ensure the supply is decoupled with a 100 nF ceramic capacitor placed within a few millimeters of the VCC pin. This page synthesizes NXP datasheet specifications, distributor pricing as of 2026-10-13, drop-in alternatives (same-brand first, then cross-brand), and practical design notes not found in the standalone datasheet to give engineers an actionable component reference.

RFQ צור קשר
PCA8525TKX - Nano-Power Automotive RTC IC, I2C | NXP
PCA8525TKX

PCA8525TKX - Nano-Power Automotive RTC IC, I2C | NXP

The NXP Semiconductors PCA8525TKX is a high-accuracy, nano-powered Real Time Clock (RTC) and calendar IC with integrated temperature compensation, an I2C-bus interface, and a temperature rating up to 125 C in a 10-lead HVSON package. It is the first RTC IC with an external crystal to feature a default temperature compensation engine, selectable between crystal curvature coefficients of -0.035 ppm/degC2 or -0.04 ppm/degC2. An RTC (real-time clock) IC is a timekeeping device that maintains seconds, minutes, hours, day, weekday, month, and year information with a 32.768 kHz watch crystal. Within the power-management and timing semiconductor hierarchy, RTC ICs form a specialized subset of clock and timing ICs optimized for ultra-low standby current rather than frequency output. RTCs run continuously even when the main processor is off, so battery-backed timekeeping accuracy and supply current are their defining metrics. Key features of the PCA8525 include nano-power supply current for extended battery life, an integrated digital temperature compensation engine that can deliver up to 5x better timekeeping accuracy than a standard uncompensated RTC, and a selectable crystal temperature model. An aging offset register further corrects long-term crystal drift, keeping timekeeping error within minutes per year rather than tens of minutes. The compensation engine periodically measures the die temperature and digitally adjusts the clock, compensating the parabolic frequency-versus-temperature characteristic of tuning-fork crystals. Because compensation is performed on-chip, no external thermistor, lookup table, or MCU overhead is needed. The I2C interface transfers all addresses and data serially, simplifying integration with any host microcontroller. Typical applications include automotive body control modules and gateway ECUs rated to 125 C ambient, smart meters, industrial dataloggers, and battery-powered IoT endpoints where both accuracy and nano-amp timekeeping current are critical. The automotive qualification makes it especially suitable for under-hood-adjacent modules requiring AEC-grade reliability. Design consideration: crystal selection matters. The compensation engine assumes a typical tuning-fork crystal model; verify that the chosen crystal's curvature coefficient matches the selectable -0.035 or -0.04 ppm/degC2 setting for guaranteed accuracy. This page synthesizes distributor sourcing data, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
PCA8543AHL - 4x60 Automotive LCD Segment Driver | NXP
PCA8543AHL

PCA8543AHL - 4x60 Automotive LCD Segment Driver | NXP

The NXP Semiconductors PCA8543AHL is an automotive-grade 4 x 60 LCD segment driver with an integrated charge pump, housed in an 80-pin LQFP package (12x12 mm). It drives any static or multiplexed LCD containing up to four backplanes, 60 segments, and 240 elements, communicating with a host MCU through a two-line bidirectional I2C-bus interface. The internal charge pump, built with on-chip capacitors, generates the LCD drive voltages without external pump components. An LCD segment driver is a peripheral IC that generates the timed multi-level waveforms required to drive liquid-crystal displays. The PCA8543 family sits at the intersection of display drivers and automotive-grade power management, bridging a host microcontroller to a character or segment LCD through standardized I2C commands. Its position in the broader hierarchy is segment driver -> display driver -> power management/interface IC -> automotive semiconductor. Key features include 4 backplanes and 60 segment outputs (240 elements total), I2C-bus control with display RAM auto-incremented addressing, an integrated charge pump for VLCD generation, and automotive temperature-grade qualification. The device is designed for low multiplex rates and supports display memory switching to minimize communication overhead. The PCA8543 is compatible with most microcontrollers. The on-chip charge pump removes the need for external high-voltage capacitors or a separate boost converter, simplifying BOM and PCB layout. Combined with low-multiplex-rate operation, this makes the device suitable for instrument-cluster, climate-control, and white-good displays that require reliable contrast over automotive temperature ranges. Typical applications include automotive instrument clusters, climate-control head units, audio head-unit displays, and industrial/HMI segment LCDs. Automotive AEC-Q100-style qualification (typical for this family) supports deployment in cabin electronics where the LCD must remain readable across cold-start and high-ambient scenarios. When designing with the PCA8543AHL, observe I2C-bus address constraints and ensure adequate decoupling near VDD and VLCD pins. Verify pinout against the 80-pin LQFP package drawing before layout to avoid reversed-orientation errors. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate this LCD driver against cross-brand equivalents.

RFQ צור קשר
PCA8565TS/1,118 - Automotive RTC, 400kHz I2C, TSSOP-8 | NXP
PCA8565TS/1,118

PCA8565TS/1,118 - Automotive RTC, 400kHz I2C, TSSOP-8 | NXP

The NXP PCA8565TS/1,118 is a CMOS Real-Time Clock (RTC) and calendar optimized for low power consumption, providing year, month, day, weekday, hours, minutes and seconds based on an external 32.768 kHz quartz crystal. It features an automotive-grade operating temperature range of -40C to +125C, supply voltage of 1.8 V to 5.5 V, and 400 kHz I2C-bus interface in an 8-pin TSSOP (8-MSOP, 3.00 mm width) package. A Real-Time Clock (RTC) is a dedicated integrated circuit that keeps track of current time and date independently of the main processor, typically using an external 32.768 kHz quartz crystal as the time base. RTCs sit in the broader hierarchy of: RTC -> clock/calendar IC -> timing component -> mixed-signal IC -> semiconductor. They are essential in any embedded system that must maintain accurate wall-clock time across power cycles, including battery-backed designs where the RTC continues counting during main supply loss. Key features of the PCA8565TS include a programmable clock output, interrupt output, integrated voltage-low detector, automatic word-address increment after each read/write, and AEC-Q100 automotive qualification per the NXP product page. The CMOS process and ultra-low standby current make it suitable for always-on systems drawing microamps in backup mode. Technically, the PCA8565TS uses an I2C slave interface with hardware-fixed slave address, communicates at up to 400 kbit/s (Fast-mode), and integrates a power-on reset, oscillator stop flag, and a trickle-charge disable bit. The BCD-coded time/date registers eliminate software-side binary-decimal conversion overhead on small MCUs. Typical applications include automotive instrument clusters, body and chassis ECUs, HVAC controllers, smart meters, industrial data loggers, and IoT edge nodes requiring a long-life backup time source. The wide 1.8 V to 5.5 V supply range allows direct connection to single-cell Li-ion, 3.3 V system rails, or 5 V legacy buses without level shifting. When designing with the PCA8565TS, ensure the 32.768 kHz crystal load capacitance matches the recommended 7 pF internal load (or use external capacitors as needed), keep the crystal traces short and guarded by ground, and reserve a backup supercapacitor or coin cell on VDD to maintain timekeeping across main power loss. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with a focus on cross-brand pin-compatible RTC substitutes for automotive and industrial designs.

RFQ צור קשר
PCA8574D,512 - 8-Bit I2C I/O Expander 400kHz SOIC-16 | NXP
PCA8574D,512

PCA8574D,512 - 8-Bit I2C I/O Expander 400kHz SOIC-16 | NXP

The NXP PCA8574D,512 is a remote 8-bit I/O expander for the I2C-bus with interrupt output, providing eight quasi-bidirectional general-purpose I/O lines in a 16-pin SOIC (SO16) package. It operates from a single 2.3V to 5.5V supply, supports the Fast-mode 400 kHz I2C bus, and offers three hardware address pins (A0, A1, A2) plus an open-drain active-low interrupt output. An I2C I/O expander is a type of interface IC that lets a microcontroller control additional digital inputs and outputs through the two-wire serial bus (SCL and SDA), reducing the number of GPIO pins the MCU itself must provide. Within the interface IC hierarchy, the PCA8574 sits alongside I2C multiplexers, port expanders and level translators, and is a direct successor in function to the industry-standard PCF8574. Key features include eight quasi-bidirectional ports that can be independently assigned as inputs or outputs, a 400 kHz I2C-bus interface, low standby current of approximately 10 uA, an latched outputs architecture with power-on reset, and an open-drain INT output that notifies the host of any input change. The quasi-bidirectional I/O structure allows a pin to be used as input or output without direction-control registers, simplifying firmware. The three hardware address pins allow up to eight PCA8574 devices (or eight PCA8574A devices with the alternate fixed slave address) on one bus, supporting up to 16 expanders and 128 I/Os, for example 128 LEDs, from a single two-wire bus. Latched outputs directly drive LEDs with high current sink capability. Typical applications include keypads and switch matrices, LED and indicator driving in white goods and industrial control panels, SPDT relay expansion, sensor monitoring in battery-powered products, and remote I/O expansion in automotive body electronics. For design, remember the quasi-bidirectional ports sink strongly but source only weakly (approximately 100 uA at VDD = 5V), so use external pull-ups on input lines and drive LEDs in sink mode. This page synthesizes distributor pricing, verified drop-in alternatives, practical design notes, and EOL lifecycle guidance not found in the manufacturer datasheet alone.

RFQ צור קשר
PCA8574D-T - 8-Bit I2C I/O Expander 400kHz | NXP
PCA8574D-T

PCA8574D-T - 8-Bit I2C I/O Expander 400kHz | NXP

The NXP PCA8574D-T is a remote 8-bit I/O expander for the I2C-bus with interrupt output, housed in a 16-pin SO16 (SOIC) package, operating at up to 400 kHz Fast-mode I2C. It provides general-purpose quasi-bidirectional I/O expansion for most microcontroller families via the two-line bidirectional I2C-bus (serial clock SCL and serial data SDA). An I/O expander is a type of interface IC within the broader hierarchy of interface and connectivity semiconductors. It allows a microcontroller with limited GPIO pins to control additional digital inputs and outputs over just two bus lines, reducing pin count, board space, and wiring complexity. I/O expanders are common companions to MCUs such as those from NXP, STMicroelectronics, and Microchip in embedded systems. Key features of the PCA8574D include an 8-bit quasi-bidirectional port with latched outputs, an open-drain interrupt (INT) output that alerts the host controller to remote input changes, and three hardware address pins (A0, A1, A2) that allow up to eight PCA8574 devices on the same I2C-bus. Combined with the PCA8574A variant (different fixed slave address), up to 16 devices can share one bus, supporting up to 128 I/Os, for example driving 128 LEDs. Architecturally, the device integrates an 8-bit quasi-bidirectional I/O port, an I2C-bus slave interface with Fast-mode 400 kHz support, and power-on reset logic that sets all ports to a defined state at startup. The quasi-bidirectional structure means each pin can serve as input or output without a direction-control register, simplifying firmware. Typical applications include keypad scanning and keyboard interfaces, LED and indicator driving, backplane status monitoring in industrial systems, and general-purpose GPIO expansion in automotive body electronics and consumer appliances. Design consideration: quasi-bidirectional pins source a weak holding current when set high, so external loads must sink current to pull a pin low; check sink capability per the manufacturer datasheet before driving heavier loads. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
PCA8575PW,118 - 16-bit I2C I/O Expander TSSOP-24 | NXP
PCA8575PW,118

PCA8575PW,118 - 16-bit I2C I/O Expander TSSOP-24 | NXP

The NXP Semiconductors PCA8575PW,118 is a remote 16-bit I/O expander for the I2C-bus (SCL/SDA), providing a 16-bit quasi-bidirectional parallel port and an interrupt output, housed in a 24-pin TSSOP (4.4 mm body width) surface-mount package and supplied on Digi-Reel. The device supports a supply range of 2.3 V to 5.5 V and operates at an I2C clock frequency up to 400 kHz (Fast-mode), making it drop-in compatible with the wide majority of 3.3 V and 5 V microcontroller I2C peripherals. An I/O expander is a bus-attach peripheral that multiplies a host controller's general-purpose I/O count by adding parallel input/output pins over a serial link. The PCA8575PW,118 belongs to the I2C-bus I/O expander family (I/O expander -> GPIO expander -> parallel I/O port -> interface IC -> integrated circuit). Quasi-bidirectional outputs can be driven low actively by the device or pulled high weakly, which lets a single pin directly sink LED current when configured as an output and still be read as a logic high when the external driver releases the line - useful for keypad scanning and switch-matrix polling. Key features include 16 individually addressable I/O lines, an open-drain interrupt (INT) line that asserts when any input changes state, three hardware address pins (A0/A1/A2) allowing up to eight devices on one bus (128 I/O total), latched outputs with high-current drive capability suitable for direct LED driving, and a low standby current that suits battery-powered designs. The integrated address decoder, input filter, and edge-triggered interrupt block reduce host firmware overhead because the MCU only services the PCA8575PW,118 when an actual port event occurs. Typical applications include adding pushbuttons, keypads, LED indicators, relay drivers, and sensor multiplexing to 8-pin microcontrollers, white-goods and appliance front panels, industrial PLC I/O modules, and PC accessory sideband ports. The 400 kHz Fast-mode I2C clock and 2.3 V to 5.5 V supply let it interface directly with 3.3 V ARM Cortex-M parts and 5 V legacy MCUs without level translation. When designing with this device, place the standard 100 nF VCC bypass within 5 mm of the supply pin and add 10 kohm pull-ups on SDA and SCL - quasi-bidirectional outputs still require external pull-ups to drive logic high reliably. Reserve the INT pin for an MCU edge-triggered input and avoid tying it permanently high; the address pins A0-A2 must be tied to a fixed logic level and not left floating at power-up. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the NXP datasheet alone, including the comparison and pinout data that engineering teams need to qualify a second source.

RFQ צור קשר
PCA9306H - Dual I2C/SMBus Voltage-Level Translator | TI
PCA9306H

PCA9306H - Dual I2C/SMBus Voltage-Level Translator | TI

The Texas Instruments PCA9306H is a dual bidirectional I2C-bus and SMBus voltage-level translator with an enable (EN) input, operating from 1.2 V to 3.3 V on VREF1 and 1.8 V to 5.5 V on VREF2, housed in an 8-pin VSSOP (DCT) package. It translates between two voltage domains without a direction pin, making it a compact solution for mixed-voltage I2C and SMBus networks. A voltage-level translator is an interface IC that safely connects digital signals operating at different supply voltages, for example a 1.8 V microcontroller I2C peripheral talking to a 3.3 V or 5 V sensor. Within the signal-chain hierarchy, the PCA9306H belongs to the level-translator family of interface ICs, positioned alongside I2C buffers, repeaters, and multiplexers. Because I2C is an open-drain bus, translation requires a bidirectional pass element rather than a directional buffer - exactly the architecture this device implements. Key features include directionless bidirectional translation, an enable pin that puts both switch channels into a high-impedance state when LOW, and low ON-state resistance of the pass FET, which keeps propagation delay minimal. The wider VREF1 range of the PCA9306H (1.2 V to 3.3 V, versus 1.0 V to 3.6 V or lower-floor variants in the family) makes it suitable for modern low-voltage processors. It supports standard-mode (100 kHz), fast-mode (400 kHz), and fast-mode plus (1 MHz) I2C devices as well as SMBus systems. Architecturally, the device is a pair of N-channel pass transistors with gate drive referenced to EN and the reference supplies. When EN is HIGH, SDA1/SCL1 connect to SDA2/SCL2; pulling either side low through its open-drain pull-up propagates the low to the other side, achieving the gate-threshold offset that produces the voltage shift. Because there is no active buffering, signal integrity is essentially transparent, with propagation delay dominated only by the switch Ron and external pull-up resistors. Typical applications include connecting 1.8 V MCUs to 3.3 V or 5 V sensors and EEPROMs, translating between 3.3 V SMBus hosts and lower-voltage peripherals in servers and networking cards, and interfacing low-voltage FPGA or SoC I2C banks to 5 V legacy buses in industrial control systems. For reliable operation, size the pull-up resistors on both sides of the translator according to the bus speed and bus capacitance; each side must have its own pull-up. Also note the 200 kOhm internal pass-gate resistance behavior at low VREF2 voltages when calculating rise times. This page synthesizes distributor data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
PCA9306USG - Dual I2C/SMBus Voltage-Level Translator | onsemi
PCA9306USG

PCA9306USG - Dual I2C/SMBus Voltage-Level Translator | onsemi

The onsemi PCA9306USG is a dual bidirectional I2C-bus and SMBus voltage-level translator with an enable (EN) input, operating from 1.2 V to 3.3 V VREF1 and 1.8 V to 5.5 V VREF2, delivering 1.5 ns typical propagation delay and 3.5 ohm ON-state resistance in an 8-pin VSSOP (US8) package. A voltage-level translator is an interface IC that allows devices operating at different supply voltages - for example a 1.8 V microcontroller and a 5 V sensor - to share the same two-wire bus safely. Within the signal-chain hierarchy, level translators sit in the interface IC family alongside I2C multiplexers, buffers, and repeaters. The PCA9306 belongs to the switch-based (passive) translator class: it uses two N-channel pass transistors per channel rather than active output stages, so the bus is pulled up naturally by the resistors on each rail. Key features include bidirectional voltage translation between 1.2 V and 5 V with no direction pin, support for Standard-mode (100 kbps), Fast-mode (400 kbps), and Fast-mode Plus (1 Mbps) I2C-bus plus SMBus operation, a very low 3.5 ohm ON-state connection that minimizes signal distortion, and an active-high EN input that isolates both buses when the translator is not needed. The 1.5 ns rise/fall propagation characteristic keeps bus timing margin intact even at Fast-mode Plus speeds. The switch architecture means the PCA9306 introduces virtually no drive strength of its own - the 64 mA figure refers to the pass-transistor current handling capability. Because it is a passive switch, lock-up free operation is guaranteed even during bus contention or partial power-down, a known failure mode of active level-shifter designs. Both SDA and SCL channels are identical, so the device handles the full 2-bit I2C bus in a single package. Typical applications include connecting 1.8 V to 3.3 V microcontrollers to 5 V I2C sensors and EEPROMs, level-shifting SMBus rails in server power supplies, battery-powered portable systems where two rail domains must communicate, and mixed-voltage industrial control modules. Design consideration: the EN pin must be driven above the higher VREF2 rail to guarantee the pass gates turn fully on; always provide pull-up resistors on both sides of each channel sized for the respective rail. This page synthesizes distributor cross-reference data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing as of 2026-10-19.

RFQ צור קשר
PCA9500BSHP - 8-Bit I/O Expander with 2-kbit EEPROM | NXP
PCA9500BSHP

PCA9500BSHP - 8-Bit I/O Expander with 2-kbit EEPROM | NXP

NXP PCA9500BSHP is an 8-bit I2C-bus and SMBus I/O expander with an integrated 2-kbit EEPROM, a 400 kHz bus interface, and a 3.6 V supply rating. The device is offered in a 16-pin HVQFN exposed-pad package for surface-mount designs. Its eight quasi-bidirectional I/O pins can be configured independently as inputs or outputs. An I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a host controller. The PCA9500BSHP sits between an I2C or SMBus controller and external board resources, allowing a processor with limited pin capacity to monitor input states or activate indicator and control devices. In the hierarchy of electronic components, it is an interface IC, a serial bus peripheral, and a port expander. The PCA9500BSHP combines three functions in one device: eight quasi-bidirectional GPIO lines, an I2C-bus or SMBus host interface, and 2 kbits of onboard EEPROM. Each GPIO can be assigned independently for input or output operation. This flexibility supports status monitoring, pushbutton or switch inputs, LED control, relay-control signals, and other board-level digital functions without requiring a dedicated GPIO pin on the host microcontroller. The integrated EEPROM provides 256 bytes of nonvolatile storage because 2 kbits divided by eight equals 256 bytes. It can be used for board identification, configuration values, calibration constants, or other small records that must survive power removal. The manufacturer identifies the device as compatible with I2C and SMBus operation up to 400 kHz, supporting common embedded serial-bus systems. PCA9500BSHP is particularly useful in embedded control and industrial equipment where a base controller needs additional digital interface lines. Typical uses include front-panel LED and switch handling, programmable relay interfaces, sensor and alarm inputs, compact automation controllers, and embedded accessory boards. NXP also identifies the device as supporting hot insertion for removable cards in backplane systems. The 16-pin HVQFN exposed-pad package makes the device appropriate for compact surface-mount assemblies, but the exposed pad requires deliberate PCB thermal and layout design. Use the manufacturer pin-description table when assigning tracks and confirm the exact package drawing, terminal numbering, pad dimensions, and exposed-pad connection before layout release. This page organizes the PCA9500BSHP interface, package, EEPROM, bus-rate, and application information with comparison guidance and practical integration notes. It also separates verified device functions from replacement considerations so engineers can assess PCB compatibility before approving a substitute.

RFQ צור קשר
PCA9500D - 8-Bit I/O Expander with EEPROM | NXP
PCA9500D

PCA9500D - 8-Bit I/O Expander with EEPROM | NXP

NXP Semiconductors PCA9500D is an 8-bit I2C and SMBus I/O port expander with an onboard 2-kbit EEPROM, eight quasi-bidirectional GPIO pins, and operation up to 400 kHz in a 16-pin SOIC package. The expander adds remote status inputs and indicator or control outputs to a host microcontroller while preserving the familiar I2C two-wire interface. An I2C I/O expander is a bus-interface peripheral that converts serial commands from a controller into parallel digital states. In the broader hierarchy, it belongs to interface ICs, digital I/O control, and general-purpose bus peripherals. The PCA9500D combines an 8-bit quasi-bidirectional port with nonvolatile storage, allowing configuration or board-identification data to be retained between power cycles. The three address pins use internal pull-up resistors, allowing up to eight devices to share the common I2C bus. The GPIO address matches the PCF8574, while the EEPROM address matches the PCF8582C-2; consequently, one device appears as two separately addressed functions to the bus master. Its 400 kHz bus rating supports faster communication than the common 100 kHz I2C operating mode. Because each port pin can be assigned independently as an input or output, the device can monitor board-level status and activate indicators such as LEDs. The quasi-bidirectional structure is useful for straightforward bus interfacing, although external pull-ups, electrical-level compatibility, and the intended input or output state must be considered in each design. Typical uses include industrial control boards, removable or backplane cards, LED and switch interfaces, configuration storage, and small embedded systems where GPIO conservation is valuable. The NXP product information specifically identifies hot-insertion support as useful in removable-card and backplane systems. A correct implementation should verify the actual device address, EEPROM map, logic thresholds, pull-up values, and pin functions against the manufacturer datasheet. Do not infer unavailable timing, voltage, temperature, or package dimensions from distributor summaries. For exact design values, consult the linked NXP documentation and validate firmware behavior across power-up, reset, bus faults, and hot-plug conditions.

RFQ צור קשר
PCA9500PW - 8-Bit I/O Expander with 2-kbit EEPROM | NXP
PCA9500PW

PCA9500PW - 8-Bit I/O Expander with 2-kbit EEPROM | NXP

The NXP Semiconductors PCA9500PW is an 8-bit I2C-bus and SMBus I/O port expander with an integrated 2-kbit EEPROM in a 16-pin TSSOP package. It operates from 2.5 V to 3.6 V, supports I2C/SMBus communication up to 400 kHz, and provides eight quasi-bidirectional data pins that can be configured independently as inputs or outputs. Three hardware address pins allow as many as eight PCA9500 devices to share one bus. According to the NXP datasheet, the bus master sees the GPIO controller and EEPROM as two separate devices, while the GPIO configuration register is accessed in a manner similar to the PCF8574. An I/O expander is a general-purpose interface IC that increases the number of digital input and output lines available to a host microcontroller without requiring a large parallel GPIO package. In the product hierarchy, the PCA9500 is an I/O expander within the broader category of interface ICs and bus-interface semiconductors. Its quasi-bidirectional ports can read external logic states or drive indicators and other digital loads, making it useful when the main processor has too few general-purpose pins for switches, sensors, LEDs, or control signals. The principal feature is the integrated 2-kbit EEPROM, which adds a small amount of nonvolatile storage for configuration or identification data. The eight GPIO pins support mixed input/output operation, and the three address inputs expand the device count available on a shared I2C or SMBus system. A maximum bus rate of 400 kHz is suitable for standard embedded control buses, while the 2.5 V to 3.6 V supply range targets conventional low-voltage digital systems. The NXP datasheet identifies the PCA9500 as a drop-in replacement for the PCF8574, adding EEPROM functionality to a familiar interface arrangement. The PCA9500 uses the same basic I2C write/read model commonly associated with PCF8574-style devices. Separate device addresses allow the GPIO function and the EEPROM to be accessed independently by the bus master. This separation is useful when the host must read or update stored data without changing live output states. Quasi-bidirectional inputs include an internal pull-up arrangement, making the device convenient for open-drain-style bus signaling and for reading switches or logic states, although external pull-up and drive-strength checks remain important in the final circuit. Typical applications include consolidating LED indicators, reading banks of switches or interlocks, adding configurable control outputs to a microcontroller module, and storing board configuration or asset information in the EEPROM. It can also reduce controller pin count in compact embedded systems while preserving a standard I2C/SMBus connection. Eight address-selectable devices provide substantial expansion without requiring additional host pins. The primary design consideration is to treat the quasi-bidirectional pins as a bidirectional interface rather than as unrestricted push-pull outputs. Check pull-up strength, voltage levels, bus capacitance, and the timing requirements of every connected peripheral. Confirm the PCB land pattern and pin numbering against the manufacturer datasheet before production because the verified product information does not provide a complete public pin table in the supplied material. This page consolidates the verified NXP product information, distributor identification, lifecycle status, bus characteristics, and manufacturer-backed drop-in relationships into an engineering-focused resource. It also distinguishes verified capabilities from parameters that still require confirmation from the full manufacturer datasheet.

RFQ צור קשר
PCA9501D - 8-Bit I2C I/O Expander with 2-kbit EEPROM | NXP
PCA9501D

PCA9501D - 8-Bit I2C I/O Expander with 2-kbit EEPROM | NXP

The NXP PCA9501D is an 8-bit I2C-bus and SMBus I/O port expander with an on-board 2-kbit EEPROM, a dedicated interrupt output and six hardware address pins, supplied in a 20-pin SO (SOIC-20) surface-mount package. An I/O expander (also called a GPIO expander or port expander) is a level-shifting serial-to-parallel interface device that converts a two-wire I2C-bus connection into a bank of individually addressable digital input/output lines. The PCA9501D sits in the hierarchy I/O expander > bus interface IC > interface IC > integrated circuit, and it is designed for designers who have run out of GPIO pins on a microcontroller, logic device or field-programmable gate array and need additional lines without growing the pin count of the main device. Key features include 8 quasi-bidirectional I/O lines (P0 through P7), an on-board 2-kbit serial EEPROM that the bus master can read and write independently of the I/O port, 6 hardware address pins that allow up to 64 PCA9501 devices to share one I2C bus, and an open-drain interrupt output that alerts the host when any input line changes state. The device operates on the standard I2C/SMBus ecosystem at up to 400 kHz, so it pairs directly with NXP microcontrollers, 3.3 V and 5 V logic families, and energy-harvesting or sensor-hub designs. Internally, the PCA9501D combines a 256-byte EEPROM array with the parallel port register set. The port lines default to high-impedance inputs and can be reconfigured individually as inputs or quasi-bidirectional outputs with an internal pull-up, which allows a single pin to read a switch and still sink current when driven low. Because the EEPROM is accessed through the same bus as the GPIO register, the bus master sees two separate I2C addresses for one physical device, and the interrupt pin removes the need for continuous polling of slow-changing inputs. Typical uses include reading banks of push buttons and configuration DIP switches, driving discrete LEDs, relay or solenoid drivers, and level shifters, adding status indicators on industrial control boards, and storing calibration or configuration data in EEPROM without spending a separate memory chip. It is also a common substitute for the PCF8574 in designs that want EEPROM and interrupt support added. When laying out the board, keep the SDA and SCL traces short, pull both lines up with a resistor in the range of 2.2 kOhm to 10 kOhm, and treat all address pins as static straps that must be tied to VDD or ground before the device is addressed. Confirm the total pull-up budget on the bus so that several expanders can share the same pair of lines.

RFQ צור קשר
PCA9501PW - 8-Bit I/O Expander with 2-kbit EEPROM | NXP
PCA9501PW

PCA9501PW - 8-Bit I/O Expander with 2-kbit EEPROM | NXP

NXP Semiconductors PCA9501PW is an 8-bit I2C and SMBus I/O expander with an integrated 2-kbit EEPROM, eight independently configurable quasi-bidirectional GPIO pins, and support for bus operation up to 400 kHz. The device is supplied in a 20-pin TSSOP package and is designed for 2.5 V to 3.6 V operation. An I/O expander is an interface IC that increases the number of digital input and output pins available to a host microcontroller or embedded processor. The PCA9501 sits within the interface IC hierarchy, where it connects a serial I2C or SMBus controller to LEDs, switches, sensors, and other board-level logic. Its quasi-bidirectional outputs can read external logic states while also driving indicator and control devices. The PCA9501 provides eight GPIO ports, a 2-kbit on-board EEPROM, an interrupt output, and six hardware address inputs. The EEPROM provides nonvolatile storage alongside the GPIO function, allowing the bus master to retain configuration or identification data. Hardware address pins allow up to 64 PCA9501 devices to coexist on one bus when address assignments and bus loading permit. The I2C and SMBus interfaces support operation at frequencies up to 400 kHz. Each GPIO may be configured independently as an input or output, and the input data and output configuration registers follow the familiar programming model of the PCF8574 family. The interrupt pin provides a hardware indication that one or more inputs have changed, reducing the need for continuous polling. Typical uses include LED and relay-control interfaces, configuration and status I/O, telecommunications equipment, networking hardware, base-station systems, and general-purpose expansion for installed boards. The integrated EEPROM also makes the device useful where a small amount of nonvolatile board data must accompany the I/O functions. Designers should account for the electrical behavior of quasi-bidirectional ports, pull up I2C and open-drain interrupt lines as required, and verify logic thresholds before driving external loads. PCB layouts should route the bus cleanly, provide stable bypass capacitance near the supply pins, and maintain adequate spacing between the TSSOP body and adjacent copper features. This page combines the verified NXP product information, manufacturer datasheet, distributor listing, and cross-reference results with practical guidance on pin behavior, bus addressing, interrupt handling, EEPROM use, PCB layout, and drop-in replacement assessment.

RFQ צור קשר
PCA9507DP,118 - 2-Wire Bus Extender, 5V, 8-TSSOP | NXP
PCA9507DP,118

PCA9507DP,118 - 2-Wire Bus Extender, 5V, 8-TSSOP | NXP

The NXP PCA9507DP,118 is a 2-wire serial bus extender with integrated 3.3 V to 5 V level shifting, one bidirectional I²C/SMBus channel, and a 400 kHz maximum clock rate, packaged in an 8-pin TSSOP (SOT505-1, DP suffix). It provides bidirectional buffering of SDA and SCL lines while preserving all I²C operating modes (master/slave, multi-master, arbitration) across the level-shift boundary, and it extends the usable bus length up to 18 meters for HDMI DDC, I²C-bus, and SMBus links. The device operates from a 2.7 V to 5.5 V supply and is specified across the -40 °C to +85 °C industrial temperature range. What is an I²C bus extender? An I²C bus extender (also called a bus repeater or accelerator) is a type of interface IC that sits between two segments of a 2-wire serial bus and buffers both SCL (clock) and SDA (data) lines. Its purpose is twofold: to overcome capacitive loading limits that cap I²C bus length, and to translate voltage levels between dissimilar supply domains. The PCA9507 sits in the broader hierarchy of bus interface ICs (interface IC > bus extender > signal buffer/repeater), and is a specialized sibling of the I²C hub/switch family such as the PCA9543A. Key features of the PCA9507DP,118 include: 1 channel of buffered SDA + SCL; support for Standard-mode (100 kHz), Fast-mode (400 kHz), and 3.4 MHz Fast-mode Plus overshoot tolerant operation on the upstream port; 2.7 V to 5.5 V supply range; 218 ns typical propagation delay; and integrated rise-time accelerators that allow designers to drop the bus pull-up resistors while still meeting rise-time budgets on long cables. It also provides hot-swap insertion tolerance so that cards can be plugged into a live backplane without corrupting the bus. The internal architecture uses two N-channel MOSFET pass gates with charge-pump enhancement, plus direction-sensing comparators that automatically configure the channel as upstream or downstream. The upstream (master-side) port tolerates 3.3 V to 5 V, while the downstream port can operate down to 2.7 V, enabling typical 3.3 V-to-5 V HDMI DDC level shifting. The TSSOP-8 footprint makes the part suitable for compact HDMI connector breakouts, display modules, and embedded backplanes. Typical applications include HDMI/DVI Display Data Channel (DDC) level shifters, I²C-bus extension over long cables (up to 18 m) in industrial control panels, SMBus fan and chassis management links, and any board-to-board 2-wire link that must bridge a voltage-level or capacitive-load gap. Because the device preserves arbitration and clock-stretching behavior, it is safe to insert in the middle of an existing multi-master bus. When designing with the PCA9507, remember that the part is a pure bus extender with no pull-ups on either side. Both upstream and downstream segments still require external pull-up resistors sized to the segment capacitance, and the device's quiescent current (typically a few hundred microamps) must be included in the system power budget. For long cables, place the PCA9507 near the connector to keep the high-impedance stub short. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes for HDMI DDC and long-cable I²C applications - context not collected in the manufacturer datasheet alone.

RFQ צור קשר
PCA9509DP,118 - I2C/SMBus Level Translating Repeater | NXP
PCA9509DP,118

PCA9509DP,118 - I2C/SMBus Level Translating Repeater | NXP

The NXP PCA9509DP,118 is a level translating I2C-bus/SMBus repeater that enables a processor low-voltage 2-wire serial bus to interface with standard I2C-bus or SMBus I/O, providing bidirectional buffering for both the SDA (data) and SCL (clock) lines at up to 400 kHz in an 8-pin TSSOP (SOT505-1) package. An I2C repeater (also called a bus buffer or redriver) is an interface IC that regenerates the two-wire serial signals so that capacitive loading and voltage-level differences do not limit bus length or device count. Within the interface-IC hierarchy (repeater -> bus buffer -> I2C/SMBus controller -> communication interface IC), repeaters sit between a low-voltage processor side and a higher-voltage peripheral side, keeping rise times and logic thresholds compliant on both segments. Key features include dual-supply level translation, supporting a low-voltage side and a standard 3 V to 5.5 V bus side, and bidirectional buffering that extends the I2C-bus by isolating capacitance on each segment. The device retains all operating modes and features of the I2C-bus system during level shifts, including clock stretching and multi-master arbitration behavior. A typical propagation delay of 109 ns and a low 2 pF input capacitance keep timing margin comfortable even at the 400 kHz fast-mode ceiling, while 5 mA supply current suits power-conscious designs. Technically, the PCA9509 uses open-drain buffer stages with rise-time acceleration so both bus segments retain true open-drain behavior: contention and backplane noise are not passed between segments, and the parts act as fault isolators between a captive processor bus and a larger peripheral bus. Typical applications include extending I2C from an MCU to backplanes and card cages, level-shifting between 1.x V/1.8 V/2.5 V processors and 3.3 V/5 V SMBus peripherals in servers, telecom line cards, and industrial control panels where bus capacitance would otherwise exceed the 400 pF I2C limit. Design-wise, plan pull-up resistor values per segment: each buffered side requires its own pull-ups sized for that segment's total capacitance, since the repeater isolates the two sides electrically. This page synthesizes distributor pricing, availability data, and practical design guidance not found in the manufacturer datasheet, with all parameters traced to NXP and distributor sources as of 2026-10-20.

RFQ צור קשר
PCA9510ADP,118 - Hot-Swap I2C/SMBus Buffer | NXP Semiconductors
PCA9510ADP,118

PCA9510ADP,118 - Hot-Swap I2C/SMBus Buffer | NXP Semiconductors

The NXP Semiconductors PCA9510ADP,118 is a hot-swappable I2C-bus and SMBus bus buffer that allows I/O card insertion into a live backplane without corrupting the data and clock buses. It is supplied in an 8-pin TSSOP (SOP) surface-mount package and buffers one channel of the two-wire serial bus at operating speeds up to 400 kHz. An I2C bus buffer (also called a bus repeater or redriver) is a two-wire interface IC that sits between an I2C or SMBus controller segment and a downstream segment. Within the interface IC hierarchy - serial interface ICs to buffers/repeaters to logic ICs - its role is to isolate bus capacitance, extend the number of devices or cable length a bus can drive, and protect one segment from faults or transients on the other. The defining feature of the PCA9510A is its hot-swap control circuitry. During card insertion, contact bounce and partial power-up can corrupt SDA and SCL lines; the PCA9510A keeps the backplane side disconnected until a stop command or bus idle condition occurs on the backplane without bus contention on the card side. Only then does it make the bidirectional connection, preserving data integrity on the live backplane. Technically, the buffer provides bidirectional buffering with rise-time acceleration on the output sides, allowing larger bus capacitance than a raw I2C port can tolerate. It supports both the standard I2C-bus and the SMBus (System Management Bus) protocol and operates from a single supply, making it a drop-in isolation element between a backplane and a removable I/O card. Typical applications include live-insertion I/O cards in telecom and server backplanes, CompactPCI-style shelves, SMBus segments in power supplies and battery-backed systems, and any hot-pluggable module that must not disturb an operating two-wire bus during insertion or removal. Design consideration: keep the two bus segments physically separated on the PCB and provide adequate pull-up resistors sized for each segment's capacitance; the buffer does not eliminate the need for correct pull-up values on either side. This page synthesizes distributor pricing context, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with all electrical data traced to the NXP PCA9510A product data sheet (Rev. 01, 8 September 2005).

RFQ צור קשר
PCA9512AD - Hot-Swap I2C/SMBus Buffer, 3.3V-5V | NXP
PCA9512AD

PCA9512AD - Hot-Swap I2C/SMBus Buffer, 3.3V-5V | NXP

The NXP PCA9512AD is a level-shifting, hot-swappable I2C-bus and SMBus buffer housed in an 8-pin SOIC package, providing bidirectional buffering for one channel at up to 400 kHz. It integrates two dedicated supply pins (VCC1 and VCC2) that allow independent 3.3 V and 5 V rails to coexist on the same bus while preserving maximum noise margin on each side. The device prevents backplane data/clock corruption during live card insertion by isolating the precharge voltages of the I/O card from the active backplane rails. An I2C/SMBus buffer is a bus repeater/accelerator that isolates two segments of a multi-drop serial bus, supports level translation between mixed-voltage nodes, and optionally accelerates the rising transitions of the SCL/SDA open-drain lines. Buffers sit between a controller and its peripherals, between two bus segments on a backplane, or between a host and removable card. The PCA9512 family belongs to NXP's broader bus-interface category, positioned between simple repeaters (e.g., PCA9507) and full multi-channel hubs (e.g., PCA9548). Hot-swap capability requires a precharge circuit that gently biases SCL/SDA before the card connector mates, avoiding the inrush glitches that would otherwise corrupt bus traffic. Key features of the PCA9512AD include 3 mA sink capability on each side per the I2C specification, support for bus voltages from 2.0 V to 5.5 V on either supply rail, and compatibility with Standard, Fast, and Fast-Plus (400 kHz) I2C modes. The buffer provides offset voltage between the two bus segments to prevent input-to-output latch-up, and it includes rise-time accelerator circuitry that minimizes bus settling time on heavily loaded segments. The 8-SO package is pin-compatible with the PCA9509 and other 8-pin I2C buffers, simplifying PCB layout reuse. The PCA9512AD is built on NXP's sub-micron CMOS process and uses an internal charge pump to drive the gate of the accelerator FETs, ensuring consistent rise-time performance across temperature. The dual-rail architecture allows designers to mix 3.3 V and 5 V devices on the same physical bus without external level translators, and the offset-impedance design prevents bus contention during simultaneous master access. ESD protection exceeds 2 kV HBM on the SCL/SDA pins. Typical applications include hot-swap I/O cards in telecom base stations, ATCA/cPCI backplane signal buffering, server management buses (IPMB, PMBus), and mixed-voltage I2C sensor aggregation. The device is commonly used where 3.3 V MCUs must communicate with 5 V legacy peripherals on the same bus segment. When designing with the PCA9512AD, ensure that VCC1 and VCC2 decoupling capacitors are placed within 2 mm of their respective supply pins. The offset voltage between bus segments must be accounted for in voltage-margin calculations, and live-insertion sequencing must guarantee that the I/O card's SCL/SDA lines reach the buffered idle state before the connector fully mates. Note: per the NXP product page, the PCA9512AD is End-of-Life, so designers should validate last-time-buy opportunities for production runs. This page synthesizes distributor pricing, drop-in alternatives, and practical design guidance that goes beyond the manufacturer datasheet, helping engineers make informed replacement and supply-chain decisions for this EOL part.

RFQ צור קשר
PCA9515AD - Dual I2C/SMBus Bus Repeater 400kHz | TI (Tape & Reel)
PCA9515AD

PCA9515AD - Dual I2C/SMBus Bus Repeater 400kHz | TI (Tape & Reel)

The Texas Instruments PCA9515AD is a dual bidirectional I2C bus and SMBus repeater (buffer/ReDriver) with 2 channels, supporting up to 400 kHz operation, supplied in an 8-pin SOIC package. It operates from a single 2.3 V to 3.6 V supply and its open-drain I2C I/O pins and enable input are 5.5-V tolerant. An I2C bus repeater is an interface buffer that isolates the capacitance and noise of one segment of an I2C or SMBus from another. Within the signal-chain hierarchy (I2C repeater -> bus buffer -> interface IC -> mixed-signal semiconductor), repeaters let a single controller address far more devices or far longer PCB traces and cables than the ~400 pF bus-capacitance limit would otherwise allow, while keeping rise times compliant. Key features include two identical bidirectional open-drain buffer channels, an active-high repeater-enable input (EN) for power-up isolation and bus segmentation, 5.5-V tolerant I2C I/O and EN for mixed-mode 3.3 V/5 V operation, and lockup-free operation that accommodates the clock-stretching and arbitration behavior of multi-master I2C systems. Technically, the PCA9515A is fabricated in a BiCMOS process. Each buffer uses a rising-edge accelerator and direction-sensing scheme that distinguishes a master-driven LOW from a slave-driven LOW, preventing the input-to-output latch-up that plagued first-generation repeaters. Because both channels are identical, the device can be used as two independent 1-bit repeaters or as a single 2-bit bus switch-style buffer. Typical applications include I2C bus segment isolation in servers and telecom cards, capacitive load expansion on long backplanes and cables, level-tolerant buffering between 3.3 V controllers and 5 V legacy peripherals, and SMBus systems in power-management and battery-pack designs. A key design consideration: the buffer is unidirectional-gain per edge, so it must not be used in loops or back-to-back without careful segmentation; place it where the bus capacitance exceeds roughly 400 pF or when isolating a noisy or fault-prone slave segment. This page adds value beyond the datasheet by synthesizing distributor pricing, verified drop-in alternatives, comparison tables, and practical layout guidance in one place.

RFQ צור קשר
PCA9515ADR - Dual I2C/SMBus Bus Repeater 400kHz | TI
PCA9515ADR

PCA9515ADR - Dual I2C/SMBus Bus Repeater 400kHz | TI

The Texas Instruments PCA9515ADR is a dual bidirectional I2C bus and SMBus repeater (buffer/ReDriver) with 2 channels, supporting up to 400 kHz operation, supplied in an 8-pin SOIC package. It operates from a single 2.3 V to 3.6 V supply and its open-drain I2C I/O pins and enable input are 5.5-V tolerant. An I2C bus repeater is an interface buffer that isolates the capacitance and noise of one segment of an I2C or SMBus from another. Within the signal-chain hierarchy (I2C repeater -> bus buffer -> interface IC -> mixed-signal semiconductor), repeaters let a single controller address far more devices or far longer PCB traces and cables than the ~400 pF bus-capacitance limit would otherwise allow, while keeping rise times compliant. Key features include two identical bidirectional open-drain buffer channels, an active-high repeater-enable input (EN) for power-up isolation and bus segmentation, 5.5-V tolerant I2C I/O and EN for mixed-mode 3.3 V/5 V operation, and lockup-free operation that accommodates the clock-stretching and arbitration behavior of multi-master I2C systems. Technically, the PCA9515A is fabricated in a BiCMOS process. Each buffer uses a rising-edge accelerator and direction-sensing scheme that distinguishes a master-driven LOW from a slave-driven LOW, preventing the input-to-output latch-up that plagued first-generation repeaters. Because both channels are identical, the device can be used as two independent 1-bit repeaters or as a single 2-bit bus switch-style buffer. Typical applications include I2C bus segment isolation in servers and telecom cards, capacitive load expansion on long backplanes and cables, level-tolerant buffering between 3.3 V controllers and 5 V legacy peripherals, and SMBus systems in power-management and battery-pack designs. A key design consideration: the buffer is unidirectional-gain per edge, so it must not be used in loops or back-to-back without careful segmentation; place it where the bus capacitance exceeds roughly 400 pF or when isolating a noisy or fault-prone slave segment. This page adds value beyond the datasheet by synthesizing distributor pricing, verified drop-in alternatives, comparison tables, and practical layout guidance in one place.

RFQ צור קשר
PCA9515ADT - 2-Channel 400kHz I2C Buffer | Texas Instruments
PCA9515ADT

PCA9515ADT - 2-Channel 400kHz I2C Buffer | Texas Instruments

The Texas Instruments PCA9515ADT is a two-channel bidirectional I2C bus and SMBus repeater operating from a 2.3 V to 3.6 V supply, supporting I2C operation up to 400 kHz in an 8-pin SOIC package. Its two identical bidirectional open-drain buffer circuits isolate and extend SDA and SCL connections while preserving bidirectional bus behavior. The active-high repeater-enable input provides a straightforward way to place each channel in a high-impedance state when it is not needed. An I2C repeater is an interface IC used to extend or segment a two-wire serial bus. I2C and SMBus systems connect controllers and peripherals through SDA and SCL, with pull-up resistors establishing the high logic level. Within the broader semiconductor hierarchy, a repeater belongs to the interface IC category and ultimately functions as a signal buffer and bus isolator. Adding a repeater can divide a long capacitive bus into shorter sections, reducing the load presented to the controller and improving signal integrity at Fast Mode speeds. The PCA9515A family provides two bidirectional channels, I2C and SMBus compatibility, active-high enable control, open-drain I/O, and mixed-mode signal support. Its I2C input/output pins and enable input are specified as 5.5 V tolerant, allowing interface signals to exceed the device's 3.6 V maximum supply voltage under the stated conditions. The architecture also supports Standard Mode and Fast Mode devices, multiple masters, and powered-off high-impedance I2C pins. The two identical channels make the PCA9515ADT useful for repeating both clock and data. Because the buffers are bidirectional, information can flow from either side of a channel through the same SDA or SCL path. The active-high enable input allows a host or reset controller to disconnect a repeated segment when isolation is required. TI identifies the device as a BiCMOS integrated circuit, combining bipolar and CMOS process characteristics in the same interface component. Typical uses include extending an I2C sensor bus, segmenting a long point-to-point connection, isolating controller and peripheral buses, and supporting mixed-mode systems that include both Standard Mode and Fast Mode devices. The 400 kHz operating capability suits sensors, EEPROMs, expanders, real-time clocks, and other common low-speed I2C peripherals. It can also assist when bus capacitance prevents one controller from reliably driving every attached device directly. Design the surrounding bus carefully because the repeater does not replace pull-up resistors or solve every signal-integrity problem. Place the device near the boundary between bus sections, provide the pull-ups required for each local segment, and confirm that enable control cannot float during power transitions. Review the manufacturer pin-description table when assigning PCB tracks and preserve adequate spacing from unrelated noisy circuitry. This page organizes the device's key electrical characteristics, application guidance, verified drop-in alternatives, and practical integration considerations. It is intended to help engineers compare bus-extension options and implement the PCA9515ADT without overlooking enable-state, voltage-tolerance, or capacitance requirements.

RFQ צור קשר