מוצרים (44,000+)

PCA9516APW - 5-Channel 400kHz I2C Bus Hub | NXP
PCA9516APW

PCA9516APW - 5-Channel 400kHz I2C Bus Hub | NXP

The NXP Semiconductors PCA9516APW is a 5-channel bidirectional I2C-bus and SMBus hub rated for operation up to 400 kHz, with open-drain input/outputs and individual active-HIGH repeater enables in a 16-pin TSSOP package. It extends an I2C bus by buffering both clock and data lines, allowing five downstream buses with up to 400 pF each. An I2C bus hub is an interface IC that regenerates and buffers SDA and SCL signals between a controller and multiple bus segments. In the product hierarchy, a bus hub is a type of I2C interface controller, interface IC, and semiconductor. This buffering approach reduces the loading presented to the upstream controller, separates downstream capacitive loads, and permits cable or board-distance extension where the original I2C bus would otherwise exceed its capacitance limit. Key features include five bidirectional repeater channels, active-HIGH individual repeater enable inputs, lock-up-free operation, support for arbitration and clock stretching across the repeater, and powered-off high-impedance I2C pins. The device accommodates Standard-mode and Fast-mode I2C devices and multiple controllers. Its operating supply range is identified by NXP as beginning at 2.3 V, while the available search results specifically describe 2.5 V and 3.3 V support. Each downstream segment can accommodate up to 400 pF. This is important because I2C uses open-drain signaling, and capacitance on SDA and SCL raises rise time and can cause timing failures. The PCA9516A architecture isolates each buffered bus segment, allowing unused channels to be disabled independently. Its powered-off high-impedance behavior helps avoid unwanted bus contention during shutdown or partial power-down conditions. Typical uses include extending sensor and EEPROM networks, isolating industrial control modules, supporting SMBus systems, and distributing clock and data to separate I2C branches. The hub is especially useful when multiple relatively slow devices create substantial bus capacitance or when a PCB layout requires electrical separation between controller and peripheral buses. Designers should connect pull-up resistors to each bus segment and place them in accordance with the bus voltage, capacitance, and rise-time requirements. Trace lengths, connector capacitance, and leakage current must be included in the worst-case electrical assessment. Disabled channels should not be assumed to provide isolation unless the enable state and powered-off pin behavior are verified for the operating condition. This page combines verified manufacturer and distributor information with practical bus-extension guidance, pricing context, package details, and replacement analysis. It is intended to help engineers determine whether a five-channel buffered hub is appropriate before committing a board design to the TSSOP-16 footprint.

RFQ צור קשר
PCA9517D - 2-Channel 400kHz I2C Level Translator | Texas Instruments
PCA9517D

PCA9517D - 2-Channel 400kHz I2C Level Translator | Texas Instruments

The Texas Instruments PCA9517D is a two-channel bidirectional I2C and SMBus buffer/repeater operating up to 400kHz, with a supply voltage range of 2.7V to 5.5V and an 8-pin SOIC package. It provides voltage-level translation between low-voltage and higher-voltage bus domains and includes independent enable control for each side. What is a level-translating I2C buffer/repeater? It is an interface IC that connects two bidirectional serial buses operating at different voltage levels. The PCA9517D belongs to the I2C repeater and voltage-level-translator hierarchy, within interface ICs and semiconductors. Its two channels isolate bus voltage domains while preserving bidirectional data transfer, helping systems separate voltage levels without redesigning the upstream and downstream devices. Key verified features include two bidirectional channels, 400kHz operation, and compatibility with I2C and SMBus applications. The device can translate signals between low-voltage domains, including voltages down to 0.9V in the NXP-described PCA9517 function, and higher-voltage domains from 2.7V to 5.5V. The 8-SOIC package supports conventional surface-mount assembly and is identified by Texas Instruments as a two-channel signal buffer/repeater. The PCA9517D is useful when two I2C domains require different voltage ranges or when a bus segment needs buffering. Its two independent enables allow unused channels to be disabled, while the bidirectional architecture supports data flow in either direction. The verified distributor listing specifies 400kHz operation and an 8-SOIC package; detailed electrical limits should be confirmed against the manufacturer datasheet before production release. Typical applications include voltage-level translation between low-voltage sensors and higher-voltage controllers, SMBus isolation between subsystems, interface conditioning between PCB domains, and embedded systems where I2C devices use different supply rails. Because it is a repeater rather than a regulator, system designers must verify pull-up voltage, bus capacitance, propagation delay, and enable sequencing on each side. A key design consideration is that both sides of each channel must be properly referenced and pulled up for the voltage domains being supported. Do not assume that level translation removes the need for correct pull-up placement or timing review. Confirm the exact pinout, enable polarity, maximum loading, and operating limits from the official Texas Instruments documentation. This page combines verified distributor information, manufacturer product identity, interface-function context, package information, and practical selection guidance to support engineers searching for a PCA9517D replacement, equivalent, pinout, price, or I2C level-translation solution.

RFQ צור קשר
PCA9517DG4 - 2-Channel 400kHz I2C Level Translator | Texas Instruments
PCA9517DG4

PCA9517DG4 - 2-Channel 400kHz I2C Level Translator | Texas Instruments

Texas Instruments PCA9517DG4 is a 2-channel bidirectional I2C bus and SMBus level-translating buffer/repeater operating up to 400 kHz, with low-side operation down to 0.9 V and high-side operation from 2.7 V to 5.5 V, in an 8-pin SOIC package. The device separates SDA and SCL buses into low-voltage and high-voltage domains so controllers and peripherals using different logic levels can communicate without direct logic-level incompatibility. An I2C level translator, also called a voltage-level translator, is an interface IC placed between two bidirectional open-drain buses. The PCA9517 belongs to the I2C buffer/repeater hierarchy, where it combines bidirectional buffering, voltage-level translation, and bus-segmentation functions. Its two-channel architecture allows SDA and SCL to cross independently between a low-voltage domain and a higher-voltage domain while preserving I2C clock stretching and SMBus-compatible operation. Key features include two bidirectional channels, operation from 0.9 V on the low side to 5.5 V on the high side, a maximum I2C bus speed of 400 kHz, and compatibility with both I2C and SMBus systems. The buffered channels can extend usable bus reach by isolating capacitance accumulated on the source side from the destination side. A quoted propagation delay of 170 ns and input capacitance of 6 pF are important when selecting pull-up resistors and evaluating timing margins. The PCA9517 uses bidirectional buffers rather than unidirectional voltage-level shifters. Because I2C and SMBus signals are open-drain and pulled up externally, each translated channel can conduct in either direction. This makes the device suitable for a host controller operating at a lower voltage communicating with sensors, memory devices, or expansion components whose pull-up network uses a higher supply voltage. The manufacturer describes the PCA9517 as a CMOS and BiCMOS integrated circuit for these applications. Typical uses include voltage adaptation between 1.8 V, 2.5 V, 3.3 V, and 5 V logic domains; isolating a long or heavily loaded I2C branch; and extending communication between a microcontroller and higher-voltage sensors or EEPROMs. Because both SDA and SCL require translation, the complete two-channel arrangement keeps data and clock voltage domains aligned. Designers must provide correct pull-up resistors on each side of the translator and account for the 170 ns propagation delay when calculating the maximum operating frequency. The 8-SOIC package is also used by the PCA9515A, while Texas Instruments' TCA9517 is identified as a comparable dual bidirectional I2C buffer. Review device-specific enable behavior, bus capacitance, and logic thresholds before finalizing a replacement. This page organizes the PCA9517DG4 specifications, replacement candidates, application guidance, and design considerations into one engineering-focused reference. It also distinguishes the published 0.9 V low-side capability from the 2.7 V to 5.5 V high-side range and identifies package and functional differences that matter when reusing an existing PCB.

RFQ צור קשר
PCA9517DR - 2-Channel 400kHz I2C Level Translator | Texas Instruments (Tape & Reel)
PCA9517DR

PCA9517DR - 2-Channel 400kHz I2C Level Translator | Texas Instruments (Tape & Reel)

The Texas Instruments PCA9517DR is a two-channel bidirectional I2C and SMBus buffer/repeater operating up to 400kHz, with a supply voltage range of 2.7V to 5.5V and an 8-pin SOIC package. It provides voltage-level translation between low-voltage and higher-voltage bus domains and includes independent enable control for each side. What is a level-translating I2C buffer/repeater? It is an interface IC that connects two bidirectional serial buses operating at different voltage levels. The PCA9517DR belongs to the I2C repeater and voltage-level-translator hierarchy, within interface ICs and semiconductors. Its two channels isolate bus voltage domains while preserving bidirectional data transfer, helping systems separate voltage levels without redesigning the upstream and downstream devices. Key verified features include two bidirectional channels, 400kHz operation, and compatibility with I2C and SMBus applications. The device can translate signals between low-voltage domains, including voltages down to 0.9V in the NXP-described PCA9517 function, and higher-voltage domains from 2.7V to 5.5V. The 8-SOIC package supports conventional surface-mount assembly and is identified by Texas Instruments as a two-channel signal buffer/repeater. The PCA9517DR is useful when two I2C domains require different voltage ranges or when a bus segment needs buffering. Its two independent enables allow unused channels to be disabled, while the bidirectional architecture supports data flow in either direction. The verified distributor listing specifies 400kHz operation and an 8-SOIC package; detailed electrical limits should be confirmed against the manufacturer datasheet before production release. Typical applications include voltage-level translation between low-voltage sensors and higher-voltage controllers, SMBus isolation between subsystems, interface conditioning between PCB domains, and embedded systems where I2C devices use different supply rails. Because it is a repeater rather than a regulator, system designers must verify pull-up voltage, bus capacitance, propagation delay, and enable sequencing on each side. A key design consideration is that both sides of each channel must be properly referenced and pulled up for the voltage domains being supported. Do not assume that level translation removes the need for correct pull-up placement or timing review. Confirm the exact pinout, enable polarity, maximum loading, and operating limits from the official Texas Instruments documentation. This page combines verified distributor information, manufacturer product identity, interface-function context, package information, and practical selection guidance to support engineers searching for a PCA9517DR replacement, equivalent, pinout, price, or I2C level-translation solution.

RFQ צור קשר
PCA9518DBR - 5-Channel 400kHz I2C Hub | Texas Instruments
PCA9518DBR

PCA9518DBR - 5-Channel 400kHz I2C Hub | Texas Instruments

The Texas Instruments PCA9518DBR is an expandable five-channel bidirectional I2C and SMBus buffer/hub operating from 3 V to 3.6 V at up to 400 kHz, supplied in a 20-pin SSOP (DB) package. It separates and buffers SDA and SCL lines into multiple downstream groups to help manage the 400 pF bus-capacitance limit defined for each I2C segment. An I2C hub is a specialized interface IC within the broader hierarchy of I2C interface devices, bus buffers, digital interface controllers, and semiconductors. It is used when a controller must communicate with more devices or over a larger wiring distance than a single unbuffered I2C segment can support. By dividing the bus into electrically isolated segments, the PCA9518DBR helps preserve signal integrity while retaining the two-wire addressing model. The principal features include five bidirectional downstream channels, a 3 V to 3.6 V operating range, 400 kHz operation, and expandable bus architecture. Each downstream side provides buffering for both clock and data, reducing the electrical loading imposed on the upstream controller. Expansion is possible by connecting additional compatible hubs in a tree arrangement, allowing designers to scale channel count without placing every peripheral on one long segment. The device supports I2C and SMBus-style bidirectional communication because both protocols depend on wired-AND data lines and shared clock signaling. Buffering minimizes the DC and capacitive loading that would otherwise accumulate as device count and conductor length increase. Designers should still evaluate pull-up placement, rise-time requirements, signal levels, and the maximum permitted bus length for each individual segment. Typical uses include sensor aggregation, industrial monitoring, test equipment, embedded control systems, and multi-board peripheral buses. The PCA9518DBR is especially useful where a microcontroller or processor must reach sensors, EEPROMs, interface converters, or other low-speed peripherals distributed across a larger assembly. For PCB implementation, keep the upstream and downstream SDA and SCL paths short, place pull-up resistors at the electrically appropriate locations, and maintain a continuous ground reference between the hub and connected devices. Review the manufacturer datasheet for the exact pin assignment, enable behavior, propagation timing, and recommended input and output capacitance before releasing the layout. This product page combines the core electrical and package characteristics with application guidance, design considerations, selection criteria, and confirmed replacement information. It helps engineers determine whether a buffered five-channel architecture is appropriate for a given I2C or SMBus topology without relying on raw catalog information alone.

RFQ צור קשר
PCA9518DBT - 5-Channel I2C Hub | Texas Instruments
PCA9518DBT

PCA9518DBT - 5-Channel I2C Hub | Texas Instruments

Texas Instruments PCA9518DBT is an expandable five-channel bidirectional I2C and SMBus buffer/hub operating from 3 V to 3.6 V at up to 400 kHz. The device is packaged in a 20-pin SSOP measuring approximately 5.30 mm wide. Its five buffered channels divide a capacitive I2C bus into groups that can each remain within the 400 pF bus-capacitance limit. The PCA9518DBT is therefore useful when system-level bus loading, wiring length, or the number of connected devices makes a single undivided I2C segment impractical. An I2C hub is an interface IC that divides one upstream serial bus into multiple downstream branches. The PCA9518 belongs to the broader I2C buffer and bus-interface hierarchy, where bidirectional level translation is combined with bus-segmentation functions. Its open-drain architecture preserves the wired-AND behavior used by I2C and SMBus, while the buffered branches isolate capacitive loading among groups of downstream devices. Each SDA and SCL path is buffered bidirectionally so the hub can support normal transfers as well as clock stretching where supported by the connected devices. The principal feature is expandability through five downstream channels. A single hub can fan one upstream I2C bus into five branches, and additional hubs can extend the hierarchy when a design requires more branches. The supported operating range of 3 V to 3.6 V suits conventional low-voltage embedded systems, while the 400 kHz operating rate accommodates fast-mode I2C communication. The open-drain buffers use pull-up resistors to establish the high level, so resistor sizing must account for the voltage, capacitance, sink current, and rise-time requirements of each branch. The PCA9518DBT uses a BiCMOS integrated-circuit implementation containing five multidirectional open-drain buffer pairs. The design allows standard low-level contention arbitration, preserves the electrical behavior expected from I2C, and separates upstream and downstream bus capacitance. Unlike a passive isolator or a unidirectional level shifter, the device supports two-way communication through every buffered branch. It also avoids the load-sharing limitations that arise when multiple devices are connected directly to one long, highly capacitive bus. Typical uses include industrial embedded-control systems, sensor aggregation, data-acquisition equipment, communications modules, programmable-instrumentation platforms, and compact computer systems with several low-speed peripheral buses. The hub is particularly useful where a processor must communicate with sensor groups, memory devices, or expansion boards distributed across a PCB. Each branch should remain below the 400 pF capacitance limit, and pull-up placement should follow the topology of the upstream and downstream segments rather than being concentrated indiscriminately on one node. A key design consideration is validating every supported operating mode with the complete bus network, including pull-up values, cable or PCB capacitance, clock-stretching behavior, and arbitration. The device does not remove the need for correct I2C rise time or for assigning unique addresses to connected peripherals. Use the manufacturer pin-description table and application information when assigning tracks and validating the 20-pin SSOP footprint. This product overview consolidates the device function, electrical boundaries, package details, application guidance, and design considerations into an engineering-focused reference. It also identifies where package or bus-topology differences can prevent an apparent substitute from serving as a true drop-in replacement.

RFQ צור קשר
PCA9518DW - 5-Channel 400kHz I2C Hub | Texas Instruments
PCA9518DW

PCA9518DW - 5-Channel 400kHz I2C Hub | Texas Instruments

The Texas Instruments PCA9518DW is an expandable five-channel bidirectional I2C and SMBus buffer hub operating from a 3 V to 3.6 V supply at up to 400 kHz. It is packaged in a 20-pin SOIC and separates buffered SDA and SCL paths into groups that can each support up to 400 pF of bus capacitance. An I2C hub is a specialized interface IC that buffers and divides one upstream I2C or SMBus segment into multiple downstream segments. The I2C protocol limits the total capacitance supported by a conventional bus to 400 pF, where the limit is determined by connected devices and cable length. The PCA9518 expands that usable bus by placing isolated buffer groups between the upstream pins and downstream channel pins, allowing additional devices to be connected without redesigning the upstream bus. Key characteristics include five bidirectional downstream channels, operation across a 3 V to 3.6 V supply range, 400-kHz bus operation, and an expandable topology supported by the TI product family. Each downstream group buffers both clock and data in the forward direction while providing the return path required by the I2C protocol. The buffered arrangement also helps isolate capacitance between downstream segments rather than presenting every device directly to the upstream bus. The PCA9518 is useful in systems where a host controller must reach multiple embedded subsystems, sensor boards, EEPROMs, power monitors, or other low-speed peripherals beyond the practical capacitance of one unbuffered bus segment. Because the device is a bidirectional buffer hub rather than a general-purpose GPIO expander, it does not add individual digital input or output ports. It preserves the two-wire serial protocol while changing the electrical segmentation of the network. Typical uses include multi-board test equipment, industrial controllers, programmable instrumentation, server management boards, and modular sensor systems. The 20-pin SOIC package also supports conventional surface-mount assembly, although a footprint confirmation against the specific manufacturer ordering information is recommended before layout release because the verified data does not provide a complete pin table. When laying out a design, treat every upstream and downstream SCL and SDA connection as a separate routed segment and place the hub close to the point where the bus must be divided. Keep stub lengths short on high-capacitance branches and follow the manufacturer layout guidance for pull-up placement. Because the verified sources describe the function, package, voltage range, frequency, and bus-capacitance segmentation but do not publish detailed pin assignments or timing tables, those specific values should be confirmed against the official PCA9518 datasheet before release.

RFQ צור קשר
PCA9518DWT - 5-Channel I2C Hub | Texas Instruments
PCA9518DWT

PCA9518DWT - 5-Channel I2C Hub | Texas Instruments

Texas Instruments PCA9518DWT is a five-channel bidirectional I2C and SMBus buffer hub designed to extend a serial bus by separating SDA and SCL into multiple groups with up to 400 pF of bus capacitance per group. It operates from 3 V to 3.6 V at up to 400 kHz and is housed in a 20-pin SOIC package. The device allows one controller-side bus to fan out to five buffered downstream channels without placing every peripheral on the same capacitive load. An I2C hub is an interface IC that buffers two-way serial-bus signals and divides one electrical bus into multiple branches. This topology extends practical bus reach beyond the 400 pF limit associated with a conventional I2C segment, reduces loading on individual branches, and improves system partitioning. The PCA9518 belongs to the broader I2C interface-controller and interface-IC hierarchy within semiconductor and bus-management electronics. The PCA9518 includes five downstream channels, bidirectional SDA and SCL propagation, and support for I2C and SMBus systems. Its 3 V to 3.6 V operating range suits low-voltage embedded equipment, while the 400 kHz bus speed covers standard- and fast-mode I2C traffic. Power-up or reset configuration and an enable or shutdown function provide control over how the hub behaves when the system starts or enters a low-power state. Buffering creates separate bus branches, but correct implementation still depends on termination, pull-up placement, channel enable sequencing, and compliance with the I2C specification. The device does not generate protocol timing; it reproduces and buffers the SCL and SDA signals. Downstream devices still require suitable pull-up resistors, and each channel should be analyzed for capacitance, voltage rise time, and signal integrity. Typical uses include sensor aggregation, industrial instrumentation, embedded control modules, programmable-logic systems, test equipment, and compact computer peripherals where several low-speed devices share a controller interface. The hub is particularly useful when cable length, device count, or branch capacitance would otherwise exceed the practical loading of one unbuffered I2C segment. Designers should preserve the recommended input and output capacitance, route SDA and SCL consistently, and review timing behavior across every enabled channel. Verify voltage compatibility, enable polarity, reset behavior, and bus rise time against the attached devices. Because the downstream branches are electrically distinct, each branch should be tested independently for contention, ringing, and recovery after clock stretching. This page summarizes the PCA9518 interface architecture, package and operating limits, verified replacement availability, and practical bus-segmentation guidance. It also identifies where a same-footprint substitute must be confirmed rather than inferred from a similar channel count, helping engineers shorten sourcing review while protecting PCB compatibility.

RFQ צור קשר
PCA9518PW - Expandable 5-Channel I2C Hub | NXP
PCA9518PW

PCA9518PW - Expandable 5-Channel I2C Hub | NXP

The NXP PCA9518PW is a BiCMOS integrated circuit designed as an expandable five-channel I2C-bus hub for I2C and SMBus systems. According to the NXP product information, the device operates from a wider 2.3 V to 3.6 V supply range and improves partial power-down performance by keeping the I2C-bus I/O pins in a high-impedance state when VDD is below 2.0 V. The component is supplied in a 20-pin TSSOP package, making it suitable for compact embedded systems that require bus expansion or buffering between a host controller and multiple peripheral devices. The PCA9518 is a type of I2C bus buffer, a specialized interface IC within the broader I2C interface and semiconductor hierarchy. Its primary function is to extend or segment an I2C bus by providing five buffered downstream channels and a separate upstream channel. This allows a controller to communicate with more peripherals than the electrical limitations of a direct bus connection would permit, while helping isolate capacitive loading and improve signal integrity in multi-device systems. The expandable architecture supports systems where additional downstream buses can be added as peripheral count and board complexity increase. Key electrical characteristics include a 2.3 V to 3.6 V operating-supply range, partial power-down support, and operation in systems using either I2C or SMBus signaling. The high-impedance bus-pin behavior below 2.0 V is especially useful when a system must prevent unintended bus activity during shutdown, reset, or partial power sequencing. The 20-pin TSSOP package provides a surface-mount form factor suitable for industrial control, embedded instrumentation, communications equipment, and consumer-accessory designs. The device is used as a bus hub rather than as a power regulator or level translator. A typical implementation places the PCA9518PW between the host I2C controller and a group of downstream peripherals. Each downstream channel can serve a separate device group, helping distribute bus capacitance and provide a controlled interface boundary. Designers must still verify pull-up resistor placement, voltage compatibility, channel-loading conditions, and the power-state behavior of every connected device. For applications requiring more than five downstream channels, multiple PCA9518 hubs can be arranged in an expandable topology. This makes the part useful in modular industrial and test systems where a controller must support multiple removable or distributed peripheral groups. The 2.3 V to 3.6 V supply range also aligns it with common low-voltage digital systems, although every connected I2C device must support the same signaling voltage and compatible electrical limits. A key design consideration is preserving the high-impedance behavior during partial power-down. The bus pins should not be externally forced when VDD falls below 2.0 V, because doing so can compromise the intended isolation behavior. PCB layout should keep the hub close to the controller or branch point, follow the datasheet’s recommended decoupling and pull-up arrangements, and avoid long unprotected branches that increase capacitance and reduce rise-time margin. Engineers should confirm the final bus timing and voltage levels with the complete peripheral population. This product page combines verified manufacturer information, distributor identification, package data, and engineering-oriented selection guidance. It also distinguishes the confirmed PCA9518PW attributes from alternatives that require independent pinout and parameter verification rather than presenting them as automatic replacements.

RFQ צור קשר
PCA9518PWR - Expandable 5-Channel I2C Hub | NXP (Tape & Reel)
PCA9518PWR

PCA9518PWR - Expandable 5-Channel I2C Hub | NXP (Tape & Reel)

The NXP PCA9518PWR is a BiCMOS integrated circuit designed as an expandable five-channel I2C-bus hub for I2C and SMBus systems. According to the NXP product information, the device operates from a wider 2.3 V to 3.6 V supply range and improves partial power-down performance by keeping the I2C-bus I/O pins in a high-impedance state when VDD is below 2.0 V. The component is supplied in a 20-pin TSSOP package, making it suitable for compact embedded systems that require bus expansion or buffering between a host controller and multiple peripheral devices. The PCA9518 is a type of I2C bus buffer, a specialized interface IC within the broader I2C interface and semiconductor hierarchy. Its primary function is to extend or segment an I2C bus by providing five buffered downstream channels and a separate upstream channel. This allows a controller to communicate with more peripherals than the electrical limitations of a direct bus connection would permit, while helping isolate capacitive loading and improve signal integrity in multi-device systems. The expandable architecture supports systems where additional downstream buses can be added as peripheral count and board complexity increase. Key electrical characteristics include a 2.3 V to 3.6 V operating-supply range, partial power-down support, and operation in systems using either I2C or SMBus signaling. The high-impedance bus-pin behavior below 2.0 V is especially useful when a system must prevent unintended bus activity during shutdown, reset, or partial power sequencing. The 20-pin TSSOP package provides a surface-mount form factor suitable for industrial control, embedded instrumentation, communications equipment, and consumer-accessory designs. The device is used as a bus hub rather than as a power regulator or level translator. A typical implementation places the PCA9518PWR between the host I2C controller and a group of downstream peripherals. Each downstream channel can serve a separate device group, helping distribute bus capacitance and provide a controlled interface boundary. Designers must still verify pull-up resistor placement, voltage compatibility, channel-loading conditions, and the power-state behavior of every connected device. For applications requiring more than five downstream channels, multiple PCA9518 hubs can be arranged in an expandable topology. This makes the part useful in modular industrial and test systems where a controller must support multiple removable or distributed peripheral groups. The 2.3 V to 3.6 V supply range also aligns it with common low-voltage digital systems, although every connected I2C device must support the same signaling voltage and compatible electrical limits. A key design consideration is preserving the high-impedance behavior during partial power-down. The bus pins should not be externally forced when VDD falls below 2.0 V, because doing so can compromise the intended isolation behavior. PCB layout should keep the hub close to the controller or branch point, follow the datasheet’s recommended decoupling and pull-up arrangements, and avoid long unprotected branches that increase capacitance and reduce rise-time margin. Engineers should confirm the final bus timing and voltage levels with the complete peripheral population. This product page combines verified manufacturer information, distributor identification, package data, and engineering-oriented selection guidance. It also distinguishes the confirmed PCA9518PWR attributes from alternatives that require independent pinout and parameter verification rather than presenting them as automatic replacements.

RFQ צור קשר
PCA9518PWT - 5-Channel 400kHz I2C Hub | Texas Instruments
PCA9518PWT

PCA9518PWT - 5-Channel 400kHz I2C Hub | Texas Instruments

Texas Instruments PCA9518PWT is a five-channel bidirectional I2C/SMBus buffer and hub operating from 3 V to 3.6 V, supporting buses up to 400 kHz. The device is packaged in a 20-pin TSSOP (PW) and is designed to divide an I2C bus into buffered groups, each supporting up to 400 pF of bus capacitance. Its five downstream channels can expand a single controller interface into multiple isolated I2C branches for larger or more distributed systems. An I2C hub is a specialized interface IC that buffers the serial data and serial clock lines between an upstream controller and one or more downstream bus segments. Buffering reduces loading on the original bus and allows additional peripherals to be connected without exceeding the 400 pF capacitance limit associated with a conventional I2C segment. The PCA9518 operates in the broader hierarchy of I2C interface controllers, bus repeaters, bus hubs, interface ICs, and semiconductors. The principal features of the PCA9518PWT include five downstream channels, bidirectional SDA and SCL buffering, a 3 V to 3.6 V supply range, and support for 400 kHz I2C operation. The buffered-channel architecture is useful when a board contains multiple sensor banks, EEPROMs, real-time clocks, display controllers, or power-management devices. Each downstream branch is isolated from the others, helping one oversized or heavily populated bus segment from degrading the entire system. Texas Instruments describes the PCA9518 as an expandable five-channel bidirectional buffer for I2C and SMBus systems. Its architecture addresses the I2C protocol's maximum 400 pF bus-capacitance constraint by separating SDA and SCL into multiple groups. The buffered branches permit longer or more complex bus arrangements than a single unbuffered segment, provided each branch remains within its electrical and capacitive limits and follows the recommended connection and pull-up arrangement. Typical uses include industrial sensor networks, multi-channel EEPROM access, data-acquisition modules, communication equipment, embedded control boards, and test systems requiring more I2C capacity than a single host bus can support. Because the hub is designed specifically for bidirectional I2C signaling, it can also support SMBus-style arrangements where the electrical and protocol requirements align. The operating-temperature grade shown for the PW package is -40 °C to 85 °C, making it suitable for commercial and industrial equipment. When laying out a PCA9518PWT design, preserve short, clean SDA and SCL paths, place pull-up resistors at the locations specified by the manufacturer, and account for the capacitive loading of every downstream branch. Confirm that each branch stays within the 400 pF limit and verify timing margin at the intended 400 kHz operating rate. Avoid treating a buffered branch as a general-purpose isolated transceiver; it remains part of the connected I2C system. This product page consolidates the manufacturer's bus-capacity constraints, operating limits, package information, and sourcing-oriented details into an engineering reference. It also distinguishes the genuine same-package family option from products that merely appear similar by function, helping designers assess footprint compatibility, I2C topology, temperature requirements, and replacement risk before committing a PCB design.

RFQ צור קשר
PCA9527DP - 3-Ch HDMI DDC/CEC I2C Bus Buffer | NXP
PCA9527DP

PCA9527DP - 3-Ch HDMI DDC/CEC I2C Bus Buffer | NXP

The NXP Semiconductors PCA9527DP is a 3-channel bidirectional open-drain bus buffer for HDMI Display Data Control (DDC) clock, data and Consumer Electronic Control (CEC), operating at up to 400 kHz from a 2.7 V to 5.5 V supply in a 10-pin TFSOP (10-TSSOP) package. A bus buffer (also called a bus extender or repeater) is a signal-conditioning device inserted between a master and a slave on a two-wire serial bus such as I2C-bus, SMBus or HDMI DDC. It belongs to the broader family of interface ICs and signal buffers, repeaters and splitters. Its role is to isolate bus capacitance on either side, so each segment sees only its own load, allowing longer cables and more devices than the raw bus standard permits. Key features of the PCA9527 include three independent bidirectional channels for SDA, SCL and CEC, support for the full 400 kHz Fast-mode I2C-bus operating range, and overvoltage-tolerant SDAx and SCLx pins. Propagation delay is a low 115 ns and input capacitance is only 8 pF, preserving setup and hold margins on long HDMI DDC cables. Architecturally, the PCA9527 uses open-drain bidirectional buffer stages with rise-time acceleration (buffer accelerator) circuitry. This rising-edge accelerator drives the bus high actively, compensating RC charging losses across long DDC lines while retaining all operating modes of the I2C-bus system during level shifting. According to the NXP datasheet, using the PCA9527 enables the system designer to isolate bus capacitance to meet the HDMI DDC version 1.3 distance specification. Typical applications include HDMI source and sink equipment (set-top boxes, TVs, monitors, AV receivers) where DDC/CEC lines must traverse cables or backplanes, notebook docking stations, and any system that extends I2C-bus or SMBus segments beyond the standard capacitance limit. The dedicated third channel carries CEC without consuming I2C channels. Design consideration: keep pull-up resistor values on both bus segments sized per segment capacitance; the accelerator helps but very heavy loads on the downstream side still degrade rise times, so verify rise-time compliance at the far end of the HDMI cable. This page adds value beyond the manufacturer datasheet by synthesizing distributor availability data, drop-in replacement guidance for this EOL part, practical design notes, and a comparison table in one place. Note: the PCA9527DP is listed by NXP as End of Life; pricing shown is indicative and all designs should plan a replacement strategy (as of 2026-10-20).

RFQ צור קשר
PCA9527DP,118 - 3-Ch I2C/HDMI DDC CEC Bus Buffer | NXP
PCA9527DP,118

PCA9527DP,118 - 3-Ch I2C/HDMI DDC CEC Bus Buffer | NXP

The NXP PCA9527DP,118 is a 3-channel bidirectional open-drain bus buffer that supports up to 400 kHz I2C-bus operation, operates from a 2.7 V to 5.5 V supply, and provides a typical 115 ns propagation delay, housed in a 10-pin TSSOP (10-TFSOP, 0.118 inch width) package with the ,118 suffix denoting a Tape & Reel, RoHS-compliant shipping option. A bus buffer (also called a bus extender or repeater) is an interface IC inserted in series with a two-wire serial bus such as I2C (Inter-Integrated Circuit) or SMBus (System Management Bus). Within the broader hierarchy of interface semiconductors, bus buffers sit alongside level translators and line drivers, and their role is to segment bus capacitance, regenerate signal edges, and isolate parasitic loading so the bus can be longer or drive more devices than the raw open-drain bus standard would otherwise permit. Key features of the PCA9527 include three independent bidirectional channels dedicated to the HDMI Display Data Channel (DDC) clock and data lines plus the Consumer Electronics Control (CEC) line, support for Fast-mode 400 kHz I2C and SMBus signaling, an active-HIGH EN enable pin with an internal pull-up of approximately 100 kOhm to VCC(B) that places the device in a low-power down state when disabled, and two separate power supply pins that allow voltage level shifting between the two sides of the bus. Technically, the device uses rise-time accelerators on each open-drain channel to actively speed up rising edges that would otherwise be limited by pull-up resistors and bus capacitance. Input capacitance is 8 pF per pin, minimizing loading on the source side, and supply current is specified up to 100 mA. Because the channels are bidirectional and open-drain, no direction-control signal is required, which is essential for the acknowledge-clock-stretching behavior of I2C and DDC. Typical applications are HDMI source, sink, repeater, and switch designs where DDC and CEC lines must be buffered between the HDMI connector and an HDMI processor, EDID EEPROM access circuits, set-top boxes, TVs, AV receivers, and projectors. The buffered DDC prevents a hot-plugged HDMI cable's cable capacitance from corrupting EDID reads, while CEC buffering preserves the single-wire control channel integrity. A key design consideration: connect the EN pin to VCC(B) if the buffer should be always active, and remember that re-enabling introduces a recovery delay, so power sequencing of the two supply pins matters in hot-plug HDMI systems. This page synthesizes distributor pricing tiers, drop-in alternative options, and practical HDMI DDC design notes that are not consolidated in the manufacturer datasheet.

RFQ צור קשר
PCA9534ADB - 8-Bit I2C I/O Expander, 16-SSOP | Texas Instruments
PCA9534ADB

PCA9534ADB - 8-Bit I2C I/O Expander, 16-SSOP | Texas Instruments

Texas Instruments PCA9534ADB is an 8-bit I2C and SMBus low-power I/O expander with interrupt output and configuration registers, designed for 2.3 V to 5.5 V operation. It supports bus speeds up to 400 kHz and is packaged in a 16-pin SSOP package for compact embedded systems. The device provides eight general-purpose remote I/O ports and three hardware address inputs, allowing multiple expanders to share one serial bus. An I/O expander is a bus-interface IC that increases the number of general-purpose input or output pins available to a host controller. The PCA9534ADB belongs to the I/O expander hierarchy within interface ICs and power management semiconductor systems. Its I2C or SMBus interface connects to a microcontroller, while the eight external pins can read logic states or control external circuits without adding another parallel GPIO port to the host board. The principal features include eight configurable I/O pins, a 2.3 V to 5.5 V operating range, 400 kHz I2C operation, an interrupt output, and configuration registers. Three address pins select one of eight fixed device addresses on the shared bus. The manufacturer specifies a -40 °C to 85 °C operating-temperature range for the PCA9534ADB ordering code. Communication with the device is register oriented. The host writes to the configuration register to select each port as input or output, reads the input and output registers to determine pin states, and uses the interrupt output to signal a change at a configured input pin. Separate input and output register behavior supports read-modify-write operations while allowing output-pin states to remain controlled independently from sensed input levels. Typical applications include industrial control modules, sensor-hub boards, programmable logic controllers, instrument panels, and compact embedded products that need additional GPIO. Eight low-voltage digital lines can monitor switches, enable converters, control indicators, or read discrete sensors. The interrupt line reduces unnecessary bus polling when an external state change occurs, which is useful in battery- and power-conscious systems. PCB design should route the I2C bus with short, compact traces and provide the decoupling and pull-up arrangements specified by the manufacturer. Confirm that the selected I/O direction, address configuration, and interrupt polarity match the firmware before release. Because the SSOP package has closely spaced leads, inspect solder-joint quality and confirm connector clearances during assembly. This product page combines manufacturer specifications, bus and register guidance, package information, application-oriented design notes, and a qualification-focused comparison with available same-footprint alternatives. It is intended to help engineers determine whether the PCA9534ADB satisfies voltage, temperature, bus-speed, package, interrupt, and software requirements before schematic capture or PCB layout.

RFQ צור קשר
PCA9534ADW - 8-Bit I2C I/O Expander | Texas Instruments
PCA9534ADW

PCA9534ADW - 8-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCA9534ADW is an 8-bit I2C/SMBus I/O expander designed for 2.3 V to 5.5 V operation, with an operating temperature range of -40 °C to 85 °C and a 16-pin SOIC package. The device adds eight configurable remote I/O lines to a host microcontroller or processor through a two-wire serial interface. An I2C I/O expander is a peripheral integrated circuit that extends the number of digital input and output lines available to a system without increasing the host controller pin count. The PCA9534A belongs to the I/O expander, interface IC, and power-management-support semiconductor hierarchy. It is useful in compact embedded products where connectors, indicators, sensors, relays, or control signals exceed the native GPIO capacity of the controller. Key features include programmable configuration registers, an interrupt output for change detection, three hardware address inputs that allow multiple devices to share one bus, and support for both I2C and SMBus operation. The manufacturer identifies a maximum bus frequency of 400 kHz for the PCA9534ADW. Its low-power design is suited to battery-powered and industrial embedded systems, while the open-drain interrupt output supports wired-OR signaling across multiple expanders. The PCA9534A uses an 8-bit parallel I/O architecture with separate input and output register organization in the device family. Each port bit can be configured for input or output, allowing a design to mix sensed inputs and driven outputs. The hardware address pins allow up to eight devices to coexist on the same two-wire bus, which simplifies distributed I/O expansion in larger control systems. Typical applications include reading push buttons, controlling LEDs, monitoring digital sensors, driving discrete logic, interfacing external connector banks, and expanding control lines in industrial controllers, test equipment, appliances, and consumer electronics. The PCA9534ADW is particularly suitable when a controller has limited GPIO pins but already supports I2C. Designers should verify the I2C pull-up resistor network, ensure the total bus capacitance remains within device limits, and define how interrupt inputs are handled. External devices driving a port pin should be checked against the configured input/output direction. Firmware must also account for the PCA9534A register differences from older parallel-port expanders rather than assuming transparent software compatibility. This product page combines the exact ordering information, package details, functional limits, drop-in alternatives, and application-oriented design guidance for engineers evaluating the PCA9534ADW. It supports faster component selection while keeping the critical distinction between electrical compatibility and complete software compatibility explicit.

RFQ צור קשר
PCA9534ADWR - 8-Bit I/O Expander | Texas Instruments
PCA9534ADWR

PCA9534ADWR - 8-Bit I/O Expander | Texas Instruments

The Texas Instruments PCA9534ADWR is an 8-bit I2C and SMBus low-power I/O expander with an interrupt output and configuration registers. It operates from 2.3 V to 5.5 V, supports bus speeds up to 400 kHz, and is packaged in a 16-pin SOIC (DW) package. The device provides eight remotely controlled general-purpose digital I/O ports through a serial bus, reducing the number of host-controller pins required for sensors, switches, indicators, and other discrete interfaces. An I/O expander is an interface IC that converts serial commands into parallel digital control lines. The PCA9534ADWR belongs to the I/O expander class, where the broader hierarchy is interface IC, bus-controlled peripheral, and low-power semiconductor. It connects to a host through the two-wire I2C bus or compatible SMBus interface, allowing the host to read input states and configure output states through registers rather than dedicating eight GPIO pins on the host. The principal features include eight configurable I/O lines, interrupt and configuration registers, operation across a 2.3 V to 5.5 V supply range, and 400 kHz I2C operation. Maximum standby current is listed as 1 uA, making the expander suitable for power-conscious embedded systems. The interrupt output is open-drain and active low, allowing multiple expansion devices to share an interrupt line when they are configured for the same bus address. Each port pin can operate as an input or output, and the configuration registers determine the direction and electrical behavior of those pins. Register-based control permits software-defined mapping between bus commands and external circuitry. The serial interface also provides a practical way to add control lines without increasing the pin count of a microcontroller, processor, or programmable logic device. The PCA9534A family is described by Texas Instruments as pin-to-pin and I2C-address compatible with the PCF8574A, although software changes are required to use its enhanced register functions. Typical applications include portable instrumentation, industrial control modules, sensor and switch interfaces, LED or relay control, programmable logic expansion, and compact embedded products. In a sensor interface, one device can gather several digital status inputs and drive multiple enables. In a control module, the same expander can operate an alarm line, mode selector, or status indicator while an interrupt tells the host that an input state has changed. Designers should verify pin multiplexing, address selection, pull-up requirements, and open-drain interrupt wiring against the manufacturer datasheet before layout is released. Bus pull-up resistors depend on the operating voltage, bus capacitance, and selected clock rate. A common interface error is treating configuration-register bits as if they were direct port states, so firmware should initialize the device explicitly and test both input and output modes during bring-up. This page combines device specifications, package and interface details, practical replacement guidance, and application-specific design guidance. It also distinguishes electrically similar devices from true pin-compatible choices, helping engineers assess replacement risk without treating a similar bus interface as proof of drop-in compatibility.

RFQ צור קשר
PCA9534APW - 8-Bit I2C I/O Expander | Texas Instruments
PCA9534APW

PCA9534APW - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCA9534APW is an 8-bit I2C and SMBus I/O expander operating from 2.3 V to 5.5 V, with a 400 kHz bus rate and interrupt output, housed in a 16-pin TSSOP package. It provides eight general-purpose remote I/O lines while supporting three hardware address inputs for connecting multiple devices on one serial bus. An I2C I/O expander is a bus-interface integrated circuit that translates serial commands into parallel digital input or output operations. Its position in the hierarchy is I/O expander, interface controller, interface IC, and integrated circuit. This makes the PCA9534APW useful when a microcontroller or processor requires more general-purpose I/O pins than its package can provide directly. The device combines an 8-bit parallel I/O port, configurable input and output registers, and an active-low open-drain interrupt output. Address pins A0, A1, and A2 allow up to eight devices to share an I2C or SMBus bus. Low standby-current consumption of 1 uA maximum helps suit low-power embedded systems, while the 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V system rails. The PCA9534A register organization includes separate port, input, output, polarity-inversion, and configuration registers, allowing each I/O line to be configured independently. This register-based control supports more flexible interrupt and input-polarity handling than simple fixed-function GPIO devices. The 400 kHz I2C interface rate provides sufficient bandwidth for routine control and status traffic. Typical applications include industrial control modules, programmable logic controllers, sensor-hub boards, appliance interfaces, LED-control boards, and compact embedded control systems. The device is particularly useful when a controller has limited spare pins but the PCB can accommodate another TSSOP-16 component and its address-selection wiring. PCB design should place the I2C pull-up resistors and device decoupling capacitor close to the relevant pins. Confirm address-strapping levels for every expander on the shared bus to prevent address conflicts, and route the active-low interrupt signal away from high-current switching nodes. This page combines device specifications, package and pin information, interface guidance, drop-in replacement candidates, and application-focused engineering notes to support faster component selection and PCB implementation.

RFQ צור קשר
PCA9534DB - 8-Bit I2C I/O Expander | Texas Instruments
PCA9534DB

PCA9534DB - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCA9534DB is an 8-bit CMOS I2C/SMBus I/O expander operating from 2.3 V to 5.5 V, supporting bus speeds up to 400 kHz and packaged in a 16-pin SSOP. It adds eight configurable general-purpose input/output ports to a host microcontroller through a two-wire serial interface and provides an interrupt output for change notification. An I2C I/O expander is a peripheral that converts a serial I2C or SMBus connection into additional parallel digital input and output lines. In the product hierarchy, it is a general-purpose I/O expander, an interface IC, and ultimately a semiconductor. The PCA9534DB is useful when a controller has too few GPIO pins for buttons, indicators, relays, logic inputs, or other digital peripherals. Its three hardware address pins permit up to eight devices to share one bus. The principal features include eight independently configurable I/O ports, a 2.3 V to 5.5 V operating range, 400 kHz I2C operation, programmable configuration registers, and an active-low interrupt output. The TI product page also states that the device is pin-to-pin and I2C-address compatible with the PCF8574, although software changes are required because the PCA9534 adds enhanced register behavior. This makes it possible to retain familiar hardware while adopting more flexible configuration and interrupt handling. Internally, the device combines a serial interface with an 8-bit port register and a configuration register that establishes input or output operation for each port bit. The VCC range supports both 3 V and 5 V powered systems, while the 400 kHz bus rating provides compatibility with common embedded-control interfaces. The provided operating-temperature information identifies a -40 C to +85 C range, and the package information identifies a 16-pin SSOP compatible with MS-013 and SOT162-1 outlines. Typical applications include industrial control panels, sensor and relay interfaces, programmable logic controllers, communications equipment, portable instrumentation, and embedded systems requiring more GPIO than the host controller provides. In each case, the PCA9534DB can connect a microcontroller to discrete digital inputs and outputs while reducing the number of direct host pins required. The interrupt line can also support event-driven designs in which the controller processes input changes only after notification. When laying out a design, place the device close to the connector or controlled peripheral and keep SDA and SCL routing short. The verified material does not specify required external pull-up values, so those must be selected from the host-bus voltage, capacitance, and bus-speed requirements. Software should also account for the PCF8574 compatibility qualification: the hardware interface is compatible, but the PCA9534 enhancements require firmware changes. This product data combines the verified manufacturer and distributor references with a practical comparison against PCF8574- and PCA9554-family devices. It distinguishes true package and pin compatibility from broader functional similarity, identifies unresolved pricing and electrical details, and highlights the design checks needed before replacing an existing I/O-expander implementation.

RFQ צור קשר
PCA9534DBR - 8-Bit I2C GPIO Expander | Texas Instruments
PCA9534DBR

PCA9534DBR - 8-Bit I2C GPIO Expander | Texas Instruments

Texas Instruments PCA9534DBR is an 8-bit I2C/SMBus general-purpose I/O expander with a 2.3 V to 5.5 V operating supply range, 400 kHz bus support, and a 16-pin SSOP package. It adds eight configurable digital input or output ports to a host processor while retaining control through the two-wire serial bus. The device also includes an interrupt output, configuration registers, and three hardware address pins that allow as many as eight devices to share one bus. An I/O expander is a low-power interface IC used to extend the number of general-purpose input/output lines available to an embedded system. Its hierarchy is GPIO expander, I/O expander, interface IC, and semiconductor. Instead of dedicating eight host-controller pins to each group of inputs and outputs, a system can place the PCA9534DBR on an I2C or SMBus and read or write its ports through register addresses. This is especially useful in compact industrial, consumer, communications, and embedded-control equipment where connector count and PCB area constrain the host MCU. Key features include eight general-purpose I/O ports, programmable addressing through A0, A1, and A2, and an open-drain interrupt output. The official Texas Instruments product information identifies a 2.3 V to 5.5 V VCC range and a 400 kHz I2C bus rate. Independent source information identifies the device as a CMOS 16-pin component and gives an operating temperature range of -40 °C to 85 °C. The SSOP package also makes the part suitable for surface-mount production and PCB footprint reuse where the package is verified against the alternate device. The PCA9534 architecture separates port data from configuration and addressing functions. A0, A1, and A2 hardware pins program the device address, while the serial interface provides access to the input, output, polarity, and configuration registers. The interrupt output allows the host to react when a selected input changes rather than continuously polling every port. Unlike devices with continuously enabled internal input pull-ups, the PCA9534 is noted by NXP as having no internal I/O pull-up resistor, reducing power consumption when outputs are held low; external pull-ups may therefore be required according to the application circuit. Typical uses include remote push-button inputs, LED and relay-control outputs, sensor and switch interfaces, backlight control, and expansion of a host processor's limited GPIO. The 400 kHz bus rate supports routine control traffic rather than high-bandwidth data transfer. Firmware should address each expander through its hardware-configured base address and initialize the configuration and polarity registers before changing port directions. Designers should verify pull-up requirements, address uniqueness, bus capacitance, and interrupt polarity for every connected device. Pull-up resistors should be sized for the lowest operating voltage and the complete bus population. I2C trace length and routing also matter because this low-power expander commonly shares a bus with sensors, EEPROMs, and other peripherals. Software for PCF8574-based designs may require changes when migrating to PCA9534 because the enhanced register behavior is not identical despite hardware compatibility. This product record combines verified manufacturer and distributor information, same-footprint alternatives, application guidance, and design cautions. It also distinguishes genuine pin-compatible choices from devices that only have similar functions, helping engineers shorten replacement evaluation without overlooking firmware and electrical differences.

RFQ צור קשר
PCA9534DW - 8-Bit I2C GPIO Expander | Texas Instruments
PCA9534DW

PCA9534DW - 8-Bit I2C GPIO Expander | Texas Instruments

The Texas Instruments PCA9534DW is an 8-bit I2C/SMBus low-power I/O expander with an interrupt output and configuration registers, operating from 2.3 V to 5.5 V in a 16-SOIC package. It provides eight general-purpose input/output ports, 400 kHz bus operation, power-on reset, and programmable input, output, and high-impedance modes according to the manufacturer product page and PCA9534 datasheet. An I2C I/O expander is a peripheral that adds digital input and output pins to a host controller through a two-wire serial interface. The PCA9534 belongs to the GPIO expander and port-extension hierarchy, where a microcontroller or processor uses serial addressing to control external LEDs, relays, sensors, or digital status signals while reducing direct GPIO requirements. Key features include eight configurable GPIO lines, a 2.3 V to 5.5 V VCC range, 400 kHz I2C/SMBus operation, push-pull outputs, an interrupt output, and configuration registers. The device is identified in distributor data as a 16-SOIC I/O expander. Its low-power design is useful for embedded systems that need additional control or monitoring lines without dedicating eight host-controller pins to every function. The PCA9534 uses configuration registers to determine whether each port pin operates as input, output, or high impedance. The interrupt output provides a hardware indication of input or register conditions, while the I2C interface allows the host to read and update port state. The 400 kHz bus rate supports relatively compact embedded control systems, although actual system throughput depends on bus capacitance, pull-up implementation, and host timing. Typical applications include low-power sensor nodes, industrial control boards, LED or indicator expansion, relay-control interfaces, and general embedded GPIO expansion. In designs using the PCA9534DW, the host processor must provide valid I2C pull-ups, respect the 2.3 V to 5.5 V supply range, and account for the interrupt pin when configuring input-change detection. The 16-SOIC package also requires a PCB footprint matching the SOIC-16 layout. For sourcing, distributor listings provide current market, price, and inventory information, while the manufacturer datasheet remains the controlling reference for pinout, register behavior, electrical limits, and application use. Product availability should be checked directly with an authorized distributor because inventory and pricing change over time.

RFQ צור קשר
PCA9534DWG4 - 8-Bit I2C I/O Expander | Texas Instruments
PCA9534DWG4

PCA9534DWG4 - 8-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCA9534DWG4 is an 8-bit CMOS I/O expander for I2C-bus and SMBus systems, operating from 2.3 V to 5.5 V with a 400 kHz bus clock in a 16-pin SOIC package. It adds eight configurable general-purpose parallel I/O ports to a host controller while providing 5 V tolerant inputs, individual port configuration, an interrupt output, and dedicated configuration registers. The wide supply-voltage range makes the device suitable for both 3.3 V and 5 V embedded systems. An I2C I/O expander belongs to the parallel-interface hierarchy: GPIO controller → I/O expander → I2C or SMBus peripheral. Its purpose is to increase the number of digital input and output lines available from a microcontroller or other bus host without adding a large number of host pins. Each expander port can be configured independently as an input or output, allowing the same device to support control signals, discrete status inputs, and external bus connections. The PCA9534DWG4 provides higher drive capability than earlier I2C port expanders, along with 5 V tolerant I/O operation and lower supply current. Individual I/O configuration allows each of the eight ports to operate in the direction required by the application. An active-low interrupt output provides an efficient way to alert the host when a change occurs on a monitored input, reducing unnecessary polling. The device uses the I2C or SMBus protocol at up to 400 kHz and includes input, output, port, and configuration registers. Address selection supports multiple expander devices on the same bus when the hardware address pins are configured appropriately. This makes the PCA9534 family suitable for structured industrial controls, embedded accessories, and compact control boards where pin count is constrained. Typical uses include reading switch banks, driving discrete LEDs or relay-control inputs, expanding sensor-control interfaces, and supporting bus-controlled peripheral boards. It is especially useful in industrial equipment, test and measurement systems, portable instruments, and consumer accessories that need additional GPIO without changing the host microcontroller. Design the PCB with the I2C pull-up resistors positioned close to the bus master or the most distant device, and confirm that their total resistance matches the bus capacitance and clock rate. Keep the interrupt trace short and route it away from high-current switching nodes. Because the SOIC package has exposed lead spacing, verify the land pattern and solder-assembly process against the manufacturer package drawing. This page combines manufacturer specifications, practical interface guidance, drop-in replacement analysis, and an application-by-application selection framework. It is intended to help engineers confirm electrical compatibility, package fit, bus behavior, and sourcing requirements before placing PCA9534DWG4 into a production design.

RFQ צור קשר
PCA9534DWR - 8-Bit I2C GPIO Expander | Texas Instruments (Tape & Reel)
PCA9534DWR

PCA9534DWR - 8-Bit I2C GPIO Expander | Texas Instruments (Tape & Reel)

The Texas Instruments PCA9534DWR is an 8-bit I2C/SMBus low-power I/O expander with an interrupt output and configuration registers, operating from 2.3 V to 5.5 V in a 16-SOIC package. It provides eight general-purpose input/output ports, 400 kHz bus operation, power-on reset, and programmable input, output, and high-impedance modes according to the manufacturer product page and PCA9534 datasheet. An I2C I/O expander is a peripheral that adds digital input and output pins to a host controller through a two-wire serial interface. The PCA9534 belongs to the GPIO expander and port-extension hierarchy, where a microcontroller or processor uses serial addressing to control external LEDs, relays, sensors, or digital status signals while reducing direct GPIO requirements. Key features include eight configurable GPIO lines, a 2.3 V to 5.5 V VCC range, 400 kHz I2C/SMBus operation, push-pull outputs, an interrupt output, and configuration registers. The device is identified in distributor data as a 16-SOIC I/O expander. Its low-power design is useful for embedded systems that need additional control or monitoring lines without dedicating eight host-controller pins to every function. The PCA9534 uses configuration registers to determine whether each port pin operates as input, output, or high impedance. The interrupt output provides a hardware indication of input or register conditions, while the I2C interface allows the host to read and update port state. The 400 kHz bus rate supports relatively compact embedded control systems, although actual system throughput depends on bus capacitance, pull-up implementation, and host timing. Typical applications include low-power sensor nodes, industrial control boards, LED or indicator expansion, relay-control interfaces, and general embedded GPIO expansion. In designs using the PCA9534DWR, the host processor must provide valid I2C pull-ups, respect the 2.3 V to 5.5 V supply range, and account for the interrupt pin when configuring input-change detection. The 16-SOIC package also requires a PCB footprint matching the SOIC-16 layout. For sourcing, distributor listings provide current market, price, and inventory information, while the manufacturer datasheet remains the controlling reference for pinout, register behavior, electrical limits, and application use. Product availability should be checked directly with an authorized distributor because inventory and pricing change over time.

RFQ צור קשר
PCA9534PW - 8-Bit I2C I/O Expander | NXP Semiconductors
PCA9534PW

PCA9534PW - 8-Bit I2C I/O Expander | NXP Semiconductors

The NXP Semiconductors PCA9534PW is an 8-bit CMOS I2C-bus and SMBus low-power I/O port expander with interrupt output, operating from 2.3 V to 5.5 V at up to 400 kHz and housed in a 16-pin TSSOP package. It adds eight configurable GPIO lines while sharing its serial bus with other peripherals. An I/O expander is an interface IC that extends a host microcontroller or processor through a serial bus instead of consuming eight parallel pins. The PCA9534 belongs to the I/O expander hierarchy, expands GPIO resources, and connects through the I2C interface to embedded control systems. Its low-power design is useful when the additional lines must remain available without continuously increasing the power budget. The PCA9534 provides eight general-purpose parallel input or output ports, an interrupt output, and configuration registers. Three hardware address pins, A0, A1, and A2, program the device address and permit multiple expanders on one I2C bus. Its 400 kHz bus capability and 2.3 V to 5.5 V operating range make it suitable for common embedded 3.3 V and 5 V systems. The device is compatible with I2C and SMBus-oriented system architectures and is designed to simplify firmware-controlled expansion of external controls and sensed signals. Inputs and outputs can be configured according to system requirements, while the interrupt output allows a controller to respond when an enabled input changes. The verified product information specifically describes PCA9534PW as the low-power TSSOP16 version of the PCA9554 family, with internal I/O pull-up resistors removed. Typical applications include industrial control boards, sensor interfaces, LED and relay-control boards, compact embedded modules, and small controller platforms that need extra parallel lines without redesigning the host package. The TSSOP-16 package also supports standard surface-mount assembly, although the exact pin names and dimensions must be confirmed in the manufacturer datasheet before layout. Designers should verify address selection, pull-up requirements, voltage compatibility, and interrupt polarity on the assembled PCB. Because the verified material identifies pin and I2C compatibility with PCF8574 while also requiring software changes, firmware should be reviewed when migrating between those devices. This page combines verified NXP, TI, and distributor information with application guidance and sourcing notes.

RFQ צור קשר
PCA9534PWR - 8-Bit I2C I/O Expander | NXP Semiconductors (Tape & Reel)
PCA9534PWR

PCA9534PWR - 8-Bit I2C I/O Expander | NXP Semiconductors (Tape & Reel)

The NXP Semiconductors PCA9534PWR is an 8-bit CMOS I2C-bus and SMBus low-power I/O port expander with interrupt output, operating from 2.3 V to 5.5 V at up to 400 kHz and housed in a 16-pin TSSOP package. It adds eight configurable GPIO lines while sharing its serial bus with other peripherals. An I/O expander is an interface IC that extends a host microcontroller or processor through a serial bus instead of consuming eight parallel pins. The PCA9534 belongs to the I/O expander hierarchy, expands GPIO resources, and connects through the I2C interface to embedded control systems. Its low-power design is useful when the additional lines must remain available without continuously increasing the power budget. The PCA9534 provides eight general-purpose parallel input or output ports, an interrupt output, and configuration registers. Three hardware address pins, A0, A1, and A2, program the device address and permit multiple expanders on one I2C bus. Its 400 kHz bus capability and 2.3 V to 5.5 V operating range make it suitable for common embedded 3.3 V and 5 V systems. The device is compatible with I2C and SMBus-oriented system architectures and is designed to simplify firmware-controlled expansion of external controls and sensed signals. Inputs and outputs can be configured according to system requirements, while the interrupt output allows a controller to respond when an enabled input changes. The verified product information specifically describes PCA9534PWR as the low-power TSSOP16 version of the PCA9554 family, with internal I/O pull-up resistors removed. Typical applications include industrial control boards, sensor interfaces, LED and relay-control boards, compact embedded modules, and small controller platforms that need extra parallel lines without redesigning the host package. The TSSOP-16 package also supports standard surface-mount assembly, although the exact pin names and dimensions must be confirmed in the manufacturer datasheet before layout. Designers should verify address selection, pull-up requirements, voltage compatibility, and interrupt polarity on the assembled PCB. Because the verified material identifies pin and I2C compatibility with PCF8574 while also requiring software changes, firmware should be reviewed when migrating between those devices. This page combines verified NXP, TI, and distributor information with application guidance and sourcing notes.

RFQ צור קשר