מוצרים (44,000+)

PCA9546ADT - 4-Channel I2C/SMBus Switch | Texas Instruments
PCA9546ADT

PCA9546ADT - 4-Channel I2C/SMBus Switch | Texas Instruments

The Texas Instruments PCA9546ADT is a 4-channel bidirectional I2C and SMBus translating switch with an active-low reset input, supplied in a 16-pin SOIC package. It fans one upstream SCL/SDA pair into four downstream channel pairs, provides three address pins for supporting up to eight devices on the I2C bus, and allows individual channels or channel combinations to be selected through programmable control registers. An I2C switch is a bus-management interface integrated circuit used to route a shared serial bus to multiple peripherals while translating logic levels. The PCA9546ADT belongs to the I2C switch family, where bidirectional translating switches sit between a controller and downstream bus nodes. Its channel-selection architecture helps designers share bus wiring without requiring every target device to have a unique fixed address. The principal features are four selectable downstream channels, I2C-bus and SMBus compatibility, three address pins, and an active-low reset input. Each downstream SCL and SD pair can be connected to the upstream bus under register control. All channels are deselected after power-up, giving the host controller a defined starting state before it configures the required downstream connection. The device is controlled through the I2C bus itself. Its control-register interface determines which downstream channels are enabled, and the three address pins give the PCA9546A family flexibility when several switches share the same upstream bus. The bidirectional translating-switch architecture permits bus-side logic-level adaptation while preserving the clock-and-data organization used by I2C and SMBus systems. Typical uses include sensor aggregation, industrial instrument interfaces, embedded control boards, test systems, and compact peripheral buses where four target devices need conditional access to one controller bus. The reset function can help a system return the switch to a known condition during initialization or fault recovery, while channel selection prevents unnecessary bus loading from unused downstream devices. PCB design should keep the upstream and downstream SCL and SD routing compact and controlled. Confirm address-pin strapping, reset polarity, logic-level compatibility, and all downstream channel states in software before enabling production traffic. Review the manufacturer pin description and electrical tables to reproduce the exact footprint and termination strategy. This page combines the PCA9546ADT interface description, verified distributor listings, packaging details, application guidance, and constrained replacement analysis. It focuses on engineering-relevant bus behavior, pin usage, reset handling, and PCB implementation rather than repeating only catalog-level identification data.

RFQ צור קשר
PCA9546ADW - 4-Channel I2C/SMBus Translating Switch with Reset | Texas Instruments
PCA9546ADW

PCA9546ADW - 4-Channel I2C/SMBus Translating Switch with Reset | Texas Instruments

The Texas Instruments PCA9546ADW is a quad bidirectional I2C and SMBus translating switch with an integrated reset function. It fans one upstream SCL/SDA pair out to four downstream SCn/SDn channel pairs, and each channel or combination of channels is selected through a programmable I2C control register. The device is offered in a 16-pin SOIC (DW) package. An I2C or SMBus bus switch, also called a bus multiplexer or fan-out buffer, is an interface IC that lets one controller talk to several targets that share the same SDA and SCL lines. Structurally, the PCA9546ADW sits in the hierarchy of interface ICs: I2C/SMBus switch -> bus multiplexer -> interface controller -> digital IC -> semiconductor. Instead of separate I2C lines running to every sensor or EEPROM, the upstream bus reaches the switch and the switch routes it to only the selected downstream segment. Key features include four independently selectable downstream channels, bidirectional pass-gate construction, an active-low RESET input that returns the internal I2C-bus state machine to a known condition and deselects all channels, and an internal power-on reset that performs the same function at startup. Two address pins allow several switch devices to coexist on one bus, and the pass-gate structure allows the VDD pin to limit the maximum high voltage that is passed through the channels. Technically, the part is a state-machine-controlled multiplexer rather than a repeater. The upstream controller writes a control byte that determines which SCn/SDn channels pass the bus. Because the pass gates are bidirectional, the same device can also be used where the direction of the bus flow changes, and the device does not regenerate or re-time the clock signal. The RESET path is the recovery mechanism of choice when a slave holds SDA low after a brown-out and blocks the bus. Typical uses include multi-sensor measurement hubs, banks of serial EEPROMs, RTC and PMIC fan-out, LED driver arrays, and industrial acquisition boards that must connect several low-voltage I2C devices to one MCU. A key design consideration is pull-up placement: the upstream pull-ups belong on the controller side, while each downstream segment needs its own pull-ups if the channel is not connected continuously. Confirm the address-strapping resistors and the RESET trace are routed so a system reset also clears the mux state. This page consolidates the switching function, reset behavior, pin assignment, drop-in alternatives, and practical layout guidance for the PCA9546ADW into one place, and adds engineering context that is not reproduced in the manufacturer datasheet.

RFQ צור קשר
PCA9546APW - 4-Channel I2C Switch with Reset | NXP
PCA9546APW

PCA9546APW - 4-Channel I2C Switch with Reset | NXP

NXP Semiconductors PCA9546APW is a four-channel bidirectional I2C-bus switch with an active-low reset input, packaged in a 16-pin TSSOP. It allows one upstream SCL/SDA pair to fan out to four downstream SCL/SDA channel pairs. Individual channels, or combinations of channels, can be selected through a programmable control register, allowing multiple downstream buses to share one host I2C controller without requiring a separate switch for every bus. An I2C-bus switch is an interface integrated circuit that routes clock and data lines between a controller and peripheral buses. Its role in the hierarchy is I2C interface switch, then bus interface IC, then interface IC, and finally semiconductor. Unlike a simple passive connection, this switch actively selects channels and provides bidirectional translation between upstream and downstream voltage domains. This makes it useful when several embedded devices or sensors must be connected to one I2C bus while maintaining individual enable control. The PCA9546A family provides four independently selectable downstream channels and a control interface connected to the upstream bus. Its active-low reset input allows the switch to recover from a stuck bus condition by returning the control register to its default state. The 16-TSSOP package is intended for surface-mount PCB assembly. Operation requires correct I2C address handling, suitable pull-up placement, and verification of downstream logic levels against the device's electrical limits. The switch supports communication with multiple downstream devices that use compatible I2C protocols and addresses. Channel selection is software-controlled through the programmable control register, so a host processor can enable only the required downstream bus at a particular time. This can reduce unnecessary bus activity and help prevent devices with the same fixed I2C address from responding simultaneously when they are connected to separate switched channels. Typical uses include sensor aggregation, industrial measurement modules, programmable instrumentation, embedded control boards, and systems that connect several low-bandwidth peripheral buses to one microcontroller. It is also appropriate for prototype and production boards requiring more than one downstream I2C branch. The design should preserve the upstream bus, isolate each downstream branch with the intended pull-up network, and account for capacitance and propagation delay introduced by the additional switch and wiring. A key implementation consideration is bus recovery. The active-low reset function can clear a channel-selection state when a downstream device holds SDA or SCL low, but designers should still provide a mechanism to cycle power or reset the affected peripheral. Validate address conflicts, logic thresholds, pull-up strength, and reset timing before using the switch with devices that operate at different voltage levels. This page combines the manufacturer product information with practical guidance for channel routing, reset behavior, PCB implementation, and replacement analysis. It also distinguishes ordering-code variants from genuinely different functions so engineers can evaluate drop-in sourcing options without mistaking a packaging suffix for a functional upgrade.

RFQ צור קשר
PCA9548ADB - 8-Channel I2C/SMBus Switch | Texas Instruments
PCA9548ADB

PCA9548ADB - 8-Channel I2C/SMBus Switch | Texas Instruments

The Texas Instruments PCA9548ADB is an 8-channel bidirectional I2C and SMBus translating switch with an active-low reset input, designed for a 2.3 V to 5.5 V operating range in a 24-pin SSOP (DB) package. It provides eight independently selectable downstream clock-and-data channel pairs, hardware addressing through three address pins, and voltage-level translation between the upstream and downstream buses. An I2C switch, also called an I2C multiplexer or bus switch, is an interface IC that routes a shared SCL and SDA connection to one or more downstream peripherals. It belongs to the I2C interface-controller and bus-management hierarchy, where it helps overcome bus-capacitance and address limitations without requiring a separate microcontroller port for every device. The PCA9548A family supports 1-of-8 bidirectional switch selection through the I2C control register. Three hardware address inputs allow as many as eight PCA9548A devices to coexist on the same upstream bus. An active-low reset input provides a hardware recovery path, while the power-up configuration selects all downstream channels according to the device configuration. Voltage translation allows the upstream SCL and SDA signals to operate from a different voltage domain than the selected downstream channel. This makes the device useful when sensors, converters, EEPROMs, and other peripherals use supply rails that differ from the controller bus. The bidirectional switch also supports bus-level clock stretching because SCL and SDA are pass-through paths rather than internally regenerated signals. Typical uses include sensor aggregation, industrial instrumentation, battery-powered portable systems, communications equipment, and embedded computing platforms that need more I2C endpoints than the main controller can support directly. The eight downstream channels reduce wiring complexity by sharing one upstream bus while allowing peripheral groups to remain isolated when they are not selected. When assigning PCB connections, use the pin-description table in the manufacturer datasheet and preserve the common ground connection between every connected supply domain. Keep the upstream bus and selected downstream pair away from unrelated high-current or high-voltage switching nodes. The reset pin should be controlled so a wedged downstream device cannot prevent recovery of the complete bus network. This page combines the manufacturer's product information, verified sourcing records, drop-in replacement analysis, comparison parameters, and practical bus-layout guidance. It is intended to help engineers evaluate the PCA9548ADB as a compact eight-channel I2C/SMBus translation and multiplexing solution.

RFQ צור קשר
PCA9548ADW - 8-Channel I2C Switch with Reset | Texas Instruments
PCA9548ADW

PCA9548ADW - 8-Channel I2C Switch with Reset | Texas Instruments

The Texas Instruments PCA9548ADW is an eight-channel bidirectional I2C and SMBus switch with an active-low reset input, three hardware address pins, and a 24-pin SOIC package. It fans one upstream SCL/SDA pair into eight downstream channels, with each channel selected independently through the I2C bus. The device is designed for systems in which multiple low-voltage bus peripherals share common serial-clock and serial-data wiring. An I2C switch is a bus-interface integrated circuit that extends or isolates a two-wire serial bus. The PCA9548ADW belongs to the bidirectional translating-switch class of interface controllers. Its upstream SCL and SDA connections communicate with a system master, while eight selectable downstream pairs connect individual sensors, EEPROMs, analog-to-digital converters, or other I2C peripherals. Voltage-level translation allows devices operating at different logic levels to share the switched bus. The main functional features include eight individually selectable bidirectional translating switches, compatibility with I2C and SMBus systems, and an active-low reset input. Three hardware address pins allow up to eight PCA9548A devices to coexist on one upstream bus. Power-up initialization deselects the downstream channels, and the reset function lets a system master recover the switch state following a timeout or other abnormal bus condition. The PCA9548ADW is controlled through the upstream I2C interface. A channel-select register identifies which one or more downstream channels should be connected, allowing unused channels to remain isolated. Bidirectional translation means that clock and data signals can propagate in either direction, supporting normal controller-to-peripheral traffic as well as acknowledged clock stretching when required by a downstream device. Typical uses include sensor aggregation, power-management controllers, smart-home equipment, industrial instrumentation, data acquisition, and embedded systems that need more I2C addresses or physical bus branches than the host bus provides. Separate downstream branches also reduce the capacitive loading associated with connecting many devices directly to one long shared bus. Designers should follow the pin-description table and recommended application circuit in the Texas Instruments datasheet when assigning address pins, bypass capacitors, reset behavior, and pull-ups. Confirm that every downstream device supports the selected voltage levels, ensure pull-up placement follows the bus topology, and review the operating temperature range of -40°C to +85°C against the product's environmental requirements. This product record combines the verified package and device description, practical bus-routing guidance, interface comparisons, and a focused explanation of channel isolation, reset control, hardware addressing, and voltage translation. These engineering details help designers determine whether the PCA9548ADW provides the required bus segmentation without introducing unnecessary board or firmware complexity.

RFQ צור קשר
PCA9548APW - 8-Channel I2C-Bus Switch with Reset | NXP Semiconductors
PCA9548APW

PCA9548APW - 8-Channel I2C-Bus Switch with Reset | NXP Semiconductors

The NXP Semiconductors PCA9548APW is an 8-channel bidirectional translating I2C-bus switch with reset, controlled via the standard I2C/SMBus interface. The SCL/SDA upstream pair fans out to eight downstream SCx/SDx channel pairs, and any individual channel or combination of channels can be selected via the programmable control register. An active-low RESET input allows the device to recover from a bus-stuck condition, a critical feature in multi-master or hot-swap systems. The device is housed in a 24-pin TSSOP (PW) package rated for -40C to +85C operation. An I2C-bus switch (or multiplexer) is a type of interface IC that sits between a single upstream I2C controller and multiple downstream I2C peripherals, allowing one controller to communicate with several devices that share the same fixed I2C address. The hierarchical position in modern electronics is: I2C switch -> I/O expander/level translator family -> interface IC -> bus management -> power management domain. The translating feature allows upstream and downstream buses to operate at different voltage levels (e.g., 3.3V host with 1.8V or 5V peripherals), eliminating the need for external level shifters. Key features include three hardware address pins (A0-A2) that allow up to eight PCA9548A devices on the same bus for a total of 64 channels, channel selection via the I2C bus, power-up with all channels deselected, low standby current, and 5.5V tolerant I/O. The RESET input is active-low and recovers the device when downstream buses are stuck LOW due to an interrupted transaction, improving system robustness. The device supports standard-mode (100 kHz), fast-mode (400 kHz), and fast-mode-plus (up to 1 MHz, depending on electrical loading). Internally, the PCA9548A uses pass-gate transistors with on-resistance suitable for both 3.3V and 5V domains, plus internal pull-up structures that maintain bus idle state when channels are deselected. The control register is written via standard I2C writes to the device's programmable address, and reads report back the currently-selected channel mask. This combination of translation, channel selection, and recovery makes the PCA9548A one of the most widely deployed I2C switches on the market. Typical applications include server and rack-backplane management (BMC and EEPROM addressing), industrial PLCs with multiple sensor arrays, NXP/TI smart batteries sharing the SMBus, lighting controllers with many identical LED drivers, and any system needing to isolate hot-swappable I2C cards. In servers, multiple PCA9548A devices allow 64+ downstream buses to be addressed by one master. Industrial automation racks often daisy-chain PCA9548As because the bus recovery feature prevents field failures when sensors are inserted or removed live. When designing with this part, place pull-up resistors on all upstream and downstream buses sized for the bus capacitance. Note that with eight downstream channels each carrying its own Rp, total Rp loading can pull down the master voltage during simultaneous switch transitions. Add a small RC delay on RESET if your system requires a defined recovery sequence. According to the manufacturer datasheet, the voltage translation requires VDD on pin 4 powering the internal logic; downstream channels draw reference from their own bus voltage, not VDD. This page synthesizes distributor stock, NXP/TI drop-in alternatives, application circuit patterns, and recovery-pin design notes in a format designed for direct AI-citation and engineer decision-making.

RFQ צור קשר
PCA9554ABS3,118 - 8-bit I2C/SMBus GPIO Expander w/ Interrupt | NXP
PCA9554ABS3,118

PCA9554ABS3,118 - 8-bit I2C/SMBus GPIO Expander w/ Interrupt | NXP

The NXP PCA9554ABS3,118 is an 8-bit I/O expander that provides General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications, housed in a 16-pin HVQFN (3x3 mm) package. It operates over a 2.3 V to 5.5 V supply range, supports clock frequencies up to 400 kHz, and features an open-drain interrupt output that asserts when any input state changes. An I/O expander (also called a GPIO expander or port expander) is a type of interface IC that adds parallel digital I/O lines to a microcontroller or processor over a low-pin-count serial bus (typically I2C or SMBus). This category sits within the broader hierarchy: GPIO expander -> I/O expander -> interface IC -> peripheral IC -> integrated circuit (semiconductor). I/O expanders are essential when the host MCU has insufficient GPIO pins for keypad scanning, LED driving, sensor multiplexing, or system status monitoring. Key features of the PCA9554ABS3,118 include 8 individually configurable I/O bits (input or output direction), hardware-selectable I2C addresses (three pins allow up to 8 devices on the same bus), 5 V tolerant I/O, and low standby current. The device conforms to the I2C-bus Fast Mode (400 kHz) specification and integrates a power-on reset circuit that initializes all ports as inputs, simplifying system bring-up. The architecture combines an I2C/SMBus slave interface, a configuration register bank, and bidirectional I/O drivers with weak pull-up enable per pin. The PCA9554A variant (versus the original PCA9554) uses a different default I2C address, allowing PCA9554 and PCA9554A devices to coexist on the same bus. An open-drain /INT pin provides change notification, freeing the host from continuous polling and reducing I2C traffic. Typical applications include mobile phone keypad and slider switch scanning, fan and cooling control in servers, LED driving and blinking control, networking equipment port status indicators, industrial PLC digital I/O expansion, and gaming consoles or set-top box button matrices. The wide 2.3 V to 5.5 V supply range allows direct interfacing with 1.8 V, 3.3 V, and 5 V MCUs without level shifters. When designing with this part, place a 100 nF decoupling capacitor within 5 mm of the VCC pin and keep the SDA/SCL traces short and impedance-controlled. Add external pull-ups (typically 4.7 kohm to 10 kohm) to SDA, SCL, and the open-drain /INT line as required by the I2C standard. Connect the exposed thermal pad to a ground plane for improved thermal and electrical performance. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, providing actionable engineering guidance beyond what distributor catalogs typically publish.

RFQ צור קשר
PCA9554ADB - 8-Bit I2C GPIO Expander | NXP Semiconductors
PCA9554ADB

PCA9554ADB - 8-Bit I2C GPIO Expander | NXP Semiconductors

The NXP Semiconductors PCA9554ADB is an 8-bit I2C and SMBus I/O expander designed for 2.3 V to 5.5 V operation, with an interrupt output and a maximum I2C bus frequency of 400 kHz. The device is offered in a 16-pin SSOP package. Its eight configurable GPIOs can be selected independently as inputs or outputs, while dedicated registers support input polling, output control, polarity inversion, and device configuration. An I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a host controller. In the electronic-component hierarchy, the PCA9554ADB belongs to the I/O expander class, interface ICs, and ultimately semiconductor devices. It communicates with a microcontroller, application processor, or other system controller through the two-wire I2C bus or SMBus, reducing direct GPIO requirements without requiring a parallel peripheral bus. The PCA9554A family provides eight independently configurable ports and an interrupt output. Three hardware address pins, A0, A1, and A2, can program the fixed I2C address and allow as many as eight devices to share one bus. Weak pull-ups are provided for the I2C interface, while configuration, input, output, and polarity-inversion registers make the ports suitable for both sensing and driving external signals. The PCA9554A architecture also provides practical address flexibility for systems containing multiple expanders. The interrupt line allows the host to detect a change on a configured input without continuously polling the input register. Its 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V systems, while the stated 400 kHz bus limit enables comparatively fast communication with the system controller. Typical uses include adding keypad or switch inputs, monitoring discrete sensors, reading LED or relay status, and controlling auxiliary digital signals in embedded equipment. It is particularly useful when the host processor has too few GPIOs for peripheral control or when a modular board requires addressable digital I/O distributed across an I2C bus. Designers should confirm the controller's logic levels, address assignment, pull-up requirements, and startup behavior in the manufacturer datasheet. Software compatibility must also be checked because the PCA9554A is pin-to-pin and I2C-address compatible with the PCF8574A, but its enhanced register architecture requires software changes. This product page combines the verified manufacturer and distributor information for the PCA9554ADB with lifecycle context, replacement guidance, interface explanations, and design-oriented selection notes. Those additions help engineers distinguish hardware compatibility from firmware compatibility and identify whether an existing PCB can be reused during sourcing transitions.

RFQ צור קשר
PCA9554ADBR - 8-Bit I2C GPIO Expander | NXP Semiconductors (Tape & Reel)
PCA9554ADBR

PCA9554ADBR - 8-Bit I2C GPIO Expander | NXP Semiconductors (Tape & Reel)

The NXP Semiconductors PCA9554ADBR is an 8-bit I2C and SMBus I/O expander designed for 2.3 V to 5.5 V operation, with an interrupt output and a maximum I2C bus frequency of 400 kHz. The device is offered in a 16-pin SSOP package. Its eight configurable GPIOs can be selected independently as inputs or outputs, while dedicated registers support input polling, output control, polarity inversion, and device configuration. An I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a host controller. In the electronic-component hierarchy, the PCA9554ADBR belongs to the I/O expander class, interface ICs, and ultimately semiconductor devices. It communicates with a microcontroller, application processor, or other system controller through the two-wire I2C bus or SMBus, reducing direct GPIO requirements without requiring a parallel peripheral bus. The PCA9554A family provides eight independently configurable ports and an interrupt output. Three hardware address pins, A0, A1, and A2, can program the fixed I2C address and allow as many as eight devices to share one bus. Weak pull-ups are provided for the I2C interface, while configuration, input, output, and polarity-inversion registers make the ports suitable for both sensing and driving external signals. The PCA9554A architecture also provides practical address flexibility for systems containing multiple expanders. The interrupt line allows the host to detect a change on a configured input without continuously polling the input register. Its 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V systems, while the stated 400 kHz bus limit enables comparatively fast communication with the system controller. Typical uses include adding keypad or switch inputs, monitoring discrete sensors, reading LED or relay status, and controlling auxiliary digital signals in embedded equipment. It is particularly useful when the host processor has too few GPIOs for peripheral control or when a modular board requires addressable digital I/O distributed across an I2C bus. Designers should confirm the controller's logic levels, address assignment, pull-up requirements, and startup behavior in the manufacturer datasheet. Software compatibility must also be checked because the PCA9554A is pin-to-pin and I2C-address compatible with the PCF8574A, but its enhanced register architecture requires software changes. This product page combines the verified manufacturer and distributor information for the PCA9554ADBR with lifecycle context, replacement guidance, interface explanations, and design-oriented selection notes. Those additions help engineers distinguish hardware compatibility from firmware compatibility and identify whether an existing PCB can be reused during sourcing transitions.

RFQ צור קשר
PCA9554ADW - 8-Bit I2C I/O Expander | Texas Instruments
PCA9554ADW

PCA9554ADW - 8-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCA9554ADW is an 8-bit I2C/SMBus GPIO expander with an operating supply range of 2.3 V to 5.5 V, a maximum bus frequency of 400 kHz, and an open-drain active-low interrupt output. The device is housed in a 16-pin SOIC package and adds eight configurable parallel I/O lines to an embedded system with limited direct GPIO resources. Configuration registers control each port direction, while the weak pull-up feature supports inputs with external pull-up resistors. An I2C I/O expander is a peripheral interface IC that converts a serial I2C or SMBus connection into additional parallel digital inputs and outputs. Its place in the hierarchy is GPIO expander, I/O expander, interface IC, and semiconductor. It reduces microcontroller pin usage while retaining individual control and status reporting for switches, indicators, sensors, and other external circuitry. The PCA9554ADW supports eight I/O ports, three hardware address inputs, interrupt output, port configuration registers, and weak pull-ups. According to the manufacturer datasheet, the A0, A1, and A2 pins permit up to eight devices to share one I2C bus. The interrupt output is open-drain and active low, allowing connected devices to signal a change in input-port state without continuous microcontroller polling. Communication is based on the two-wire I2C interface, with SCL and SDA pins and a stated operating frequency up to 400 kHz. The device supports a 2.3 V to 5.5 V supply range, making it suitable for common embedded rails. Its eight quasi-bidirectional I/O ports can be configured individually as inputs or outputs, while the configuration and polarity registers support bus-oriented control requirements. Typical uses include industrial control modules, sensor-hub boards, LED and switch interfaces, compact data-acquisition equipment, and general-purpose embedded controller platforms. An I2C GPIO expander is especially useful when the host controller has too few pins for external switches, status indicators, isolators, or sensor interfaces. The active-low interrupt path helps conserve processor resources when only occasional input changes occur. PCB implementation requires careful bus layout. Keep SDA and SCL traces short, provide the pull-up network required by the system, and route the interrupt trace away from high-current switching nodes. Confirm address-strapping levels and port directions during firmware initialization, and account for the SOIC package's 16-pin footprint when planning assembly. This page combines interface details, application guidance, pin information, comparison context, and design-focused considerations to support faster component selection and PCB planning. Engineers can use the application sections to identify suitable host-controller arrangements, while the design notes highlight bus, addressing, and interrupt considerations that are important beyond the basic component specifications.

RFQ צור קשר
PCA9554APW - 8-Bit I2C GPIO Expander | NXP
PCA9554APW

PCA9554APW - 8-Bit I2C GPIO Expander | NXP

NXP Semiconductors PCA9554APW is an 8-bit I2C-bus and SMBus parallel I/O expander with an active-low interrupt output, configurable input or output ports, and a 16-pin TSSOP package. It supports an operating supply range of 2.3 V to 5.5 V, communicates at up to 400 kHz, and provides eight general-purpose I/O pins for extending a host microcontroller or processor across control, monitoring, and industrial interface systems. An I/O expander is a semiconductor interface device that translates serial I2C commands into parallel digital signals. In the product hierarchy, the PCA9554APW belongs to the I2C I/O expander class, within interface ICs and broader semiconductor control systems. Its purpose is to reduce the number of GPIO pins required by the host while preserving individually configurable input, output, and polarity behavior across an eight-bit port. Key features include eight individually selectable I/O directions, an input register, an output register, and a polarity-inversion register. The active-low, open-drain interrupt output provides an efficient way to signal the host when a monitored input changes state. Three address pins permit multiple devices to coexist on one I2C bus, while the fixed address of the PCA9554A differs from that of the PCA9554, allowing both device types to share the same bus without address conflicts. The PCA9554APW uses serial command and data transfers over SDA and SCL, while the eight parallel lines operate independently as inputs or outputs. The operating supply range of 2.3 V to 5.5 V makes the device suitable for systems using 2.5 V, 3.3 V, or 5 V logic. At the specified 400 kHz maximum bus rate, software transactions and interrupt handling should be verified against the host timing requirements and bus capacitance of the completed design. Typical uses include industrial control panels, sensor aggregation, LED and relay interfaces, keyboard scanners, programmable input/output modules, and compact embedded systems where the host lacks sufficient GPIO pins. The interrupt line is particularly useful when several expander inputs must be monitored without continuous register polling, although the host must still handle the I2C transaction that reads the relevant input state. Design the power path with local supply decoupling close to VDD and ground, and route SDA and SCL as short, clean bus traces. Account for address selection, pull-up resistor selection, open-drain interrupt handling, and the electrical levels of every connected peripheral. Verify that all external signals remain within the device's supply and input limits, and confirm the final pin mapping against the manufacturer pin-description table before fabrication. This product page combines the NXP manufacturer specifications, interface architecture, application guidance, and structured comparison with verified same-footprint alternatives. It also highlights the differences among I2C address options, supply ranges, interrupt behavior, and package variants so engineers can identify a replacement without changing the PCB footprint.

RFQ צור קשר
PCA9554D - 8-Bit I2C/SMBus GPIO Expander | NXP
PCA9554D

PCA9554D - 8-Bit I2C/SMBus GPIO Expander | NXP

The NXP Semiconductors PCA9554D is an 8-bit I2C-bus and SMBus general-purpose I/O expander with interrupt, available in a 16-pin SO package. It adds eight configurable GPIO lines to a host processor through the I2C interface, while the interrupt output provides a change indication so the controller does not need to poll continuously. The verified product listing identifies the device as an interface IC for I2C/SMBus I/O expansion and specifically identifies PCA9554D as having a different address from PCA9554A. An 8-bit I/O expander is a peripheral interface device: when a microcontroller lacks sufficient GPIO pins, the expander converts serial I2C transactions into parallel input or output signals. Its place in the hierarchy is I/O expander → bus interface peripheral → interface IC → semiconductor. The PCA9554D can be used to reduce host pin count while adding control, monitoring, and configurable logic connections. The supplied sources describe the device as a 16-pin CMOS part with eight general-purpose I/O lines and an interrupt function, but they do not provide the complete electrical limits, address table, pin names, temperature range, or package dimensions. Those values are therefore marked as data needed rather than inferred. The part is listed by NXP as End of Life, so new designs should verify availability and consider the official replacement information before committing to production. The PCA9554D remains useful for maintaining existing I2C GPIO designs, particularly where 400 kHz I2C operation and SO16 packaging are relevant. Its interrupt feature helps the host respond to external state changes while conserving bus bandwidth. Because the verified sources do not confirm a current manufacturer-recommended drop-in replacement, any alternative must be checked carefully for pin compatibility, address behavior, electrical limits, package dimensions, and lifecycle status.

RFQ צור קשר
PCA9554DB - 8-Bit I2C I/O Expander, 5.5V | TI
PCA9554DB

PCA9554DB - 8-Bit I2C I/O Expander, 5.5V | TI

The Texas Instruments PCA9554DB is an 8-bit I2C/SMBus I/O expander with interrupt, weak pull-ups, and configuration registers, operating from 2.3 V to 5.5 V in a 16-pin SSOP package. According to the verified product listing, it supports I2C/SMBus communication at up to 400 kHz and provides eight general-purpose remote I/O ports. An I/O expander is an interface IC that increases the number of input and output lines available to a microcontroller or other host processor. The PCA9554 belongs to the I2C interface-controller hierarchy: it connects through the two-line bidirectional bus using SCL and SDA, while its eight parallel pins can be configured individually as inputs or outputs. This makes it useful when a system needs remote control, monitoring, or signal-interface expansion without adding a larger microcontroller package. The verified listing identifies weak pull-ups, an interrupt output, and configuration registers as defining features. Configuration registers allow the host to define each port direction and control output states, while the interrupt output provides a change notification mechanism for input events. The 2.3 V to 5.5 V operating range supports both low-voltage and conventional 5 V system rails, subject to the host and bus requirements. The PCA9554DB is identified as a 16-SSOP I/O expander by DigiKey, with an operating bus frequency of 400 kHz. This combination of eight configurable I/O lines, interrupt support, and a compact surface-mount package makes the device suitable for embedded control, remote sensing, keypad or display interfaces, and small automation systems. Designers should confirm the device address, pull-up implementation, electrical limits, and interrupt polarity against the manufacturer datasheet before finalizing a board. The verified data does not provide pin-level naming, output-current limits, or detailed timing values, so those parameters require verification rather than assumption.

RFQ צור קשר
PCA9554DBR - 8-Bit I2C I/O Expander, 5.5V | TI (Tape & Reel)
PCA9554DBR

PCA9554DBR - 8-Bit I2C I/O Expander, 5.5V | TI (Tape & Reel)

The Texas Instruments PCA9554DBR is an 8-bit I2C/SMBus I/O expander with interrupt, weak pull-ups, and configuration registers, operating from 2.3 V to 5.5 V in a 16-pin SSOP package. According to the verified product listing, it supports I2C/SMBus communication at up to 400 kHz and provides eight general-purpose remote I/O ports. An I/O expander is an interface IC that increases the number of input and output lines available to a microcontroller or other host processor. The PCA9554 belongs to the I2C interface-controller hierarchy: it connects through the two-line bidirectional bus using SCL and SDA, while its eight parallel pins can be configured individually as inputs or outputs. This makes it useful when a system needs remote control, monitoring, or signal-interface expansion without adding a larger microcontroller package. The verified listing identifies weak pull-ups, an interrupt output, and configuration registers as defining features. Configuration registers allow the host to define each port direction and control output states, while the interrupt output provides a change notification mechanism for input events. The 2.3 V to 5.5 V operating range supports both low-voltage and conventional 5 V system rails, subject to the host and bus requirements. The PCA9554DBR is identified as a 16-SSOP I/O expander by DigiKey, with an operating bus frequency of 400 kHz. This combination of eight configurable I/O lines, interrupt support, and a compact surface-mount package makes the device suitable for embedded control, remote sensing, keypad or display interfaces, and small automation systems. Designers should confirm the device address, pull-up implementation, electrical limits, and interrupt polarity against the manufacturer datasheet before finalizing a board. The verified data does not provide pin-level naming, output-current limits, or detailed timing values, so those parameters require verification rather than assumption.

USD $1.55 במלאי
PCA9554DW - 8-Bit I/O Expander | Texas Instruments
PCA9554DW

PCA9554DW - 8-Bit I/O Expander | Texas Instruments

The Texas Instruments PCA9554DW is an 8-bit I2C/SMBus I/O expander with interrupt, weak pull-up, and configuration registers. Its operating supply-voltage range is 2.3 V to 5.5 V, its I2C clock frequency is 400 kHz, and it is supplied in a 16-SOIC package. The device adds eight serial-controlled digital I/O lines to a host processor while conserving microcontroller pins. An I/O expander is an interface IC that converts a serial bus into parallel digital input or output lines. In the product hierarchy, PCA9554DW belongs to I/O expander controllers within interface ICs and broader semiconductor devices. The PCA9554 includes one 8-bit configuration register, input register, output register, and polarity-inversion register. At power-on, its I/O ports are inputs with weak pull-ups, and the system master can subsequently configure each line as input or output. Three hardware address pins, A0, A1, and A2, program the fixed I2C address and allow up to eight devices to share one I2C bus or SMBus. The open-drain active-low interrupt output provides a change notification from the remote I/O ports. According to the Texas Instruments product page, PCA9554 is pin-to-pin and I2C-address compatible with the PCF8574, although software changes are required because PCA9554 adds configuration-register functionality. The PCA9554DW is useful for low-cost control of LEDs, relays, sensors, keys, and other digital peripherals where the host has insufficient GPIO pins. It can reduce MCU package size and pin count, while the interrupt line lets the processor sleep until an input event occurs. Inputs can also be configured with polarity inversion to simplify active-high or active-low system logic. Design attention should focus on bus pull-ups, address selection, output transition timing, and the electrical limits of each remote port. Weak pull-ups are intended primarily for power-up defaults, not as a replacement for strong external pull-ups on a heavily loaded I2C bus. Confirm external-device logic levels and avoid driving a port in a way that conflicts with its alternate input or output function. This page combines verified manufacturer and distributor information with package, application, comparison, and design guidance. It distinguishes confirmed replacements from unverified substitutions and preserves missing electrical values rather than estimating them. The result helps engineers identify whether PCA9554DW fits a new design or whether a documented same-package alternative requires additional validation.

RFQ צור קשר
PCA9554DWR - 8-Bit I/O Expander | Texas Instruments (Tape & Reel)
PCA9554DWR

PCA9554DWR - 8-Bit I/O Expander | Texas Instruments (Tape & Reel)

The Texas Instruments PCA9554DWR is an 8-bit I2C/SMBus I/O expander with interrupt, weak pull-up, and configuration registers. Its operating supply-voltage range is 2.3 V to 5.5 V, its I2C clock frequency is 400 kHz, and it is supplied in a 16-SOIC package. The device adds eight serial-controlled digital I/O lines to a host processor while conserving microcontroller pins. An I/O expander is an interface IC that converts a serial bus into parallel digital input or output lines. In the product hierarchy, PCA9554DWR belongs to I/O expander controllers within interface ICs and broader semiconductor devices. The PCA9554 includes one 8-bit configuration register, input register, output register, and polarity-inversion register. At power-on, its I/O ports are inputs with weak pull-ups, and the system master can subsequently configure each line as input or output. Three hardware address pins, A0, A1, and A2, program the fixed I2C address and allow up to eight devices to share one I2C bus or SMBus. The open-drain active-low interrupt output provides a change notification from the remote I/O ports. According to the Texas Instruments product page, PCA9554 is pin-to-pin and I2C-address compatible with the PCF8574, although software changes are required because PCA9554 adds configuration-register functionality. The PCA9554DWR is useful for low-cost control of LEDs, relays, sensors, keys, and other digital peripherals where the host has insufficient GPIO pins. It can reduce MCU package size and pin count, while the interrupt line lets the processor sleep until an input event occurs. Inputs can also be configured with polarity inversion to simplify active-high or active-low system logic. Design attention should focus on bus pull-ups, address selection, output transition timing, and the electrical limits of each remote port. Weak pull-ups are intended primarily for power-up defaults, not as a replacement for strong external pull-ups on a heavily loaded I2C bus. Confirm external-device logic levels and avoid driving a port in a way that conflicts with its alternate input or output function. This page combines verified manufacturer and distributor information with package, application, comparison, and design guidance. It distinguishes confirmed replacements from unverified substitutions and preserves missing electrical values rather than estimating them. The result helps engineers identify whether PCA9554DWR fits a new design or whether a documented same-package alternative requires additional validation.

RFQ צור קשר
PCA9554N - 8-Bit I2C GPIO Expander | NXP | DIP-16
PCA9554N

PCA9554N - 8-Bit I2C GPIO Expander | NXP | DIP-16

NXP Semiconductors PCA9554N is an 8-bit I2C-bus and SMBus general-purpose input/output expander with interrupt output, weak internal pull-up resistors, and operation from 2.3 V to 5.5 V. The device is packaged in a 16-lead plastic dual in-line package with a 2.54 mm lead pitch and a 19 mm × 6.35 mm × 4.2 mm body. It adds eight configurable GPIO lines to a host processor through a two-wire serial bus. An I2C GPIO expander is a peripheral interface IC that converts serial I2C or SMBus commands into parallel digital inputs and outputs. It extends the number of control and status pins available from a microcontroller or application processor while preserving the processor's limited I/O resources. The PCA9554 belongs to the interface IC hierarchy and supports address configuration, input/output direction control, port registers, and an interrupt mechanism for input-state changes. The PCA9554N provides eight GPIO pins, three hardware address inputs, a 400 kHz I2C interface, an interrupt output, and weak internal pull-ups. Address pins A0, A1, and A2 permit multiple devices to share one bus, with the manufacturer describing support for as many as eight devices on the same I2C or SMBus bus. Each port bit can be configured independently as input or output, making the device useful for control, monitoring, and status signaling functions. Communication with the PCA9554N uses the standard two-wire SCL and SDA signals alongside VCC and ground. The interrupt output provides a hardware indication that a change occurred on a configured input port, allowing the host to respond without continuously polling all eight inputs. Weak internal pull-ups assist with open-drain bus signaling but are intended mainly for lightly loaded conditions; external pull-up resistors should be selected according to bus voltage, capacitance, and clock rate. Typical applications include industrial control panels, sensor interfaces, relay and LED monitoring, configuration port expansion, battery-powered instrumentation, and embedded systems requiring more GPIO than the host controller provides. The 2.3 V to 5.5 V operating range permits use with both 3.3 V and 5 V systems, while the DIP-16 mechanical format is convenient for prototyping, through-hole assembly, and manually reworkable laboratory boards. PCB design should preserve the standard DIP-16 footprint with 2.54 mm pitch and place decoupling close to VCC and ground. Confirm that every I2C node uses a unique address combination and that pull-up resistance satisfies the bus rise-time requirements at the intended 400 kHz maximum operating rate. Firmware must also configure each port direction correctly before treating a pin as an output. This product page combines manufacturer package information, interface capabilities, source-referenced alternatives, comparison parameters, and practical implementation guidance. It is intended to help engineers assess GPIO capacity, bus compatibility, package reuse, and firmware requirements before selecting a replacement or integrating the device into a new design.

RFQ צור קשר
PCA9554PW - 8-Bit I/O Expander with Interrupt | NXP
PCA9554PW

PCA9554PW - 8-Bit I/O Expander with Interrupt | NXP

The NXP Semiconductors PCA9554PW is an 8-bit CMOS I2C/SMBus GPIO expander with interrupt, operating from 2.3 V to 5.5 V and supporting bus speeds up to 400 kHz. It adds eight configurable general-purpose input/output pins to a host controller through the two-wire bus and is packaged in a 16-pin TSSOP. The PCA9554PW also provides configurable input/output polarity and configuration registers, enabling firmware-defined port behavior without consuming additional host GPIO pins. An I2C or SMBus I/O expander is an interface IC that bridges a serial control bus and parallel digital lines. In the product hierarchy, it belongs to interface ICs, then bus interface controllers, then GPIO expanders, and finally semiconductors. It reduces the number of host-controller pins required for control-panel status LEDs, switch inputs, alarm signals, and other low-to-moderate-speed digital I/O. Unlike a microcontroller, the PCA9554PW is not intended to execute application software; a connected processor reads and writes its registers through I2C. The verified product data identifies eight parallel I/O lines, interrupt support, weak pull-up capability, configuration registers, a 2.3 V to 5.5 V supply range, and operation at both 100 kHz and 400 kHz bus rates. Distributor listings identify the PW package as 16-pin TSSOP. These features suit systems where local logic voltage is below 5.5 V and the designer needs deterministic register-based port expansion. The interrupt output can notify the host when a configured input changes, reducing unnecessary polling while preserving straightforward firmware control. The PCA9554 family uses configurable registers to define each port line as input or output and to control input polarity inversion. The verified NXP result specifically distinguishes PCA9554PW from PCA9554A, whose address differs. Firmware, pull-up implementation, and power sequencing therefore need review before substituting the A variant into an existing design. The verified data does not provide complete electrical limits, output-drive capability, timing values, or detailed pin mapping, so those items must be confirmed in the manufacturer datasheet before layout or sign-off. Typical applications include remote control-panel indicators, configuration and mode switches, keypad or button inputs, alarm and interrupt signaling, small industrial modules, and low-speed embedded controllers. Placing eight digital lines behind one I2C address is especially useful when the host MCU has insufficient spare pins. The 400 kHz capability shortens transfer time compared with 100 kHz operation, although actual bus timing remains bounded by the slowest device, pull-up resistance, capacitance, and firmware behavior. Design with the I2C pull-ups on SDA and SCL, keep the interrupt trace short, and confirm signal levels against the host supply. Do not assume that every similarly named PCA9554 device has the same address or register behavior. A socketed prototype should be tested for address conflicts, bus capacitance, input polarity, and active interrupt behavior. This page combines verified manufacturer and distributor facts with engineering guidance while clearly separating unavailable specifications. The product information on this page also highlights why direct MPN review matters: package suffix, address variant, and bus details determine interchangeability. Before ordering or replacing PCA9554PW, verify the exact suffix, lifecycle status, pinout, and electrical limits against current manufacturer documentation.

RFQ צור קשר
PCA9554PWG4 - 8-Bit I2C I/O Expander | Texas Instruments
PCA9554PWG4

PCA9554PWG4 - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCA9554PWG4 is an 8-bit I2C/SMBus I/O expander with a 400 kHz bus interface, interrupt output, configuration registers, and 2.3 V to 5.5 V operating supply in a 16-pin TSSOP package. It adds eight configurable parallel I/O ports to a host controller while minimizing the number of pins required on the microcontroller or processor. An I/O expander is an interface IC that extends a serial control bus into parallel digital inputs and outputs. The PCA9554 belongs to the hierarchy of I2C interface controllers, peripheral interface ICs, and general-purpose I/O expansion devices. It is useful when a system needs more GPIO pins than are available on its host controller, when inputs must be located remotely from the main processor, or when a shared two-wire bus offers a practical alternative to dedicating multiple host pins. The PCA9554PWG4 provides eight general-purpose I/O ports, push-pull output capability, a dedicated interrupt output, and weak pull-ups. Its 2.3 V to 5.5 V supply range supports both 3 V and 5 V systems. A 400 kHz I2C interface provides a practical balance between bus speed and integration density. The manufacturer also identifies configuration registers, allowing the host to read port state, change port direction, and detect input changes through the interrupt mechanism. Operationally, the device supports both input and output modes on the same eight-port bank. Inputs can be polled by reading the input-port register, while changes can be reported through the active-low interrupt output. The interrupt line allows the host to remain asleep or perform other work until an input event requires attention. The I2C interface includes A0, A1, and A2 address pins, allowing multiple expanders to share the same bus when the system requires additional I/O ports. The PCA9554PWG4 is used in embedded control boards, industrial automation modules, programmable logic controllers, communication equipment, appliance controllers, test systems, and compact sensor or switch interfaces. It is especially useful when an I2C-capable microcontroller has insufficient pins for relays, indicators, buttons, selectors, or isolation-compatible digital inputs. Its small TSSOP package also supports compact board layouts where a larger parallel interface would be impractical. For PCB design, place the bypass capacitor close to VDD and route SDA and SCL as a controlled-length bus with appropriate pull-up resistors. Confirm the logic-voltage levels of the host and all connected devices, define each port direction during startup, and account for the interrupt line when constructing the system wake-up path. The pin-description table in the manufacturer datasheet should be used when assigning tracks. This product page combines the manufacturer overview, verified package and interface characteristics, drop-in comparison options, and practical implementation guidance for engineers evaluating an 8-bit TSSOP I/O expander.

RFQ צור קשר
PCA9554PWR - 8-Bit I/O Expander with Interrupt | NXP (Tape & Reel)
PCA9554PWR

PCA9554PWR - 8-Bit I/O Expander with Interrupt | NXP (Tape & Reel)

The NXP Semiconductors PCA9554PWR is an 8-bit CMOS I2C/SMBus GPIO expander with interrupt, operating from 2.3 V to 5.5 V and supporting bus speeds up to 400 kHz. It adds eight configurable general-purpose input/output pins to a host controller through the two-wire bus and is packaged in a 16-pin TSSOP. The PCA9554PWR also provides configurable input/output polarity and configuration registers, enabling firmware-defined port behavior without consuming additional host GPIO pins. An I2C or SMBus I/O expander is an interface IC that bridges a serial control bus and parallel digital lines. In the product hierarchy, it belongs to interface ICs, then bus interface controllers, then GPIO expanders, and finally semiconductors. It reduces the number of host-controller pins required for control-panel status LEDs, switch inputs, alarm signals, and other low-to-moderate-speed digital I/O. Unlike a microcontroller, the PCA9554PWR is not intended to execute application software; a connected processor reads and writes its registers through I2C. The verified product data identifies eight parallel I/O lines, interrupt support, weak pull-up capability, configuration registers, a 2.3 V to 5.5 V supply range, and operation at both 100 kHz and 400 kHz bus rates. Distributor listings identify the PW package as 16-pin TSSOP. These features suit systems where local logic voltage is below 5.5 V and the designer needs deterministic register-based port expansion. The interrupt output can notify the host when a configured input changes, reducing unnecessary polling while preserving straightforward firmware control. The PCA9554 family uses configurable registers to define each port line as input or output and to control input polarity inversion. The verified NXP result specifically distinguishes PCA9554PWR from PCA9554A, whose address differs. Firmware, pull-up implementation, and power sequencing therefore need review before substituting the A variant into an existing design. The verified data does not provide complete electrical limits, output-drive capability, timing values, or detailed pin mapping, so those items must be confirmed in the manufacturer datasheet before layout or sign-off. Typical applications include remote control-panel indicators, configuration and mode switches, keypad or button inputs, alarm and interrupt signaling, small industrial modules, and low-speed embedded controllers. Placing eight digital lines behind one I2C address is especially useful when the host MCU has insufficient spare pins. The 400 kHz capability shortens transfer time compared with 100 kHz operation, although actual bus timing remains bounded by the slowest device, pull-up resistance, capacitance, and firmware behavior. Design with the I2C pull-ups on SDA and SCL, keep the interrupt trace short, and confirm signal levels against the host supply. Do not assume that every similarly named PCA9554 device has the same address or register behavior. A socketed prototype should be tested for address conflicts, bus capacitance, input polarity, and active interrupt behavior. This page combines verified manufacturer and distributor facts with engineering guidance while clearly separating unavailable specifications. The product information on this page also highlights why direct MPN review matters: package suffix, address variant, and bus details determine interchangeability. Before ordering or replacing PCA9554PWR, verify the exact suffix, lifecycle status, pinout, and electrical limits against current manufacturer documentation.

RFQ צור קשר
PCA9554U - 8-Bit I2C I/O Expander with Interrupt | NXP
PCA9554U

PCA9554U - 8-Bit I2C I/O Expander with Interrupt | NXP

The NXP Semiconductors PCA9554U is an 8-bit CMOS I2C-bus and SMBus parallel I/O port with an interrupt output, supplied in a 16-pin SOIC package. It operates from 2.3 V to 5.5 V, supports I2C and SMBus communication up to 400 kHz, and adds eight configurable GPIO lines to a host processor through a two-wire serial interface. Its 16-pin package and low-voltage operation suit compact embedded, industrial, and consumer control systems. An I2C I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a microcontroller or other bus master. The PCA9554U belongs to the parallel I/O expander hierarchy, where an 8-bit port registers are connected to an I2C-controlled serial interface. This architecture preserves processor I/O resources while allowing switches, indicators, sensors, and other external circuitry to share a common bus. The device includes an 8-bit configuration register, input register, output register, and polarity-inversion register. Each port pin can be configured independently as an input or output, and input polarity can be inverted for devices that generate active-low signals. Power-on defaults place all I/O pins in input mode with weak pull-ups. An active-low interrupt output provides a hardware indication that an input state has changed, reducing the need for continuous bus polling. Three hardware address inputs, A0, A1, and A2, allow up to eight devices to share one I2C bus. This address arrangement makes the PCA9554U useful in systems that require several independent groups of GPIO. The fixed I2C address is programmed by the three address pins, while the serial interface provides read access to input-port data and write access to output and configuration registers. The NXP device is pin-to-pin and I2C-address compatible with the PCF8574 series, although enhanced register behavior requires corresponding firmware changes described in NXP Application Note AN469. Typical uses include reading control buttons and selector switches, driving LED indicators, monitoring discrete alarm signals, and expanding interface lines for industrial controllers. The 2.3 V to 5.5 V operating range allows operation from common 3.3 V and 5 V rails. At 400 kHz, the interface is suitable for mainstream embedded control buses where throughput is sufficient for periodic status updates rather than continuous high-rate data streaming. A practical design must keep the interrupt and I2C signal levels compatible with the host bus. Use pull-ups on SDA and SCL as required by the bus, connect the address pins to ground or VCC for the intended device address, and provide local decoupling near VCC. Review the I2C pull-up resistance against bus capacitance, speed, voltage, and the number of connected devices to avoid excessive rise times or signal-integrity problems. This product page combines the manufacturer device information, package and pin information, drop-in replacement analysis, and practical implementation guidance. It also distinguishes the PCA9554U from address or package variants so engineers can confirm mechanical compatibility, register behavior, and required firmware changes before assigning a replacement to an existing PCB.

RFQ צור קשר
PCA9555BSHP - 16-Bit I2C I/O Expander | NXP | HVQFN-24
PCA9555BSHP

PCA9555BSHP - 16-Bit I2C I/O Expander | NXP | HVQFN-24

The NXP Semiconductors PCA9555BSHP is a 16-bit I2C-bus and SMBus I/O expander with an interrupt output, operating at bus speeds up to 400 kHz and supporting a maximum supply voltage of 5.5 V. The device is offered in a 24-HVQFN package measuring 4 x 4 mm and is supplied in tape-and-reel packaging. Its 16 port pins can be configured individually as inputs or outputs, allowing a host microcontroller to monitor external signals and control LEDs, relays, or other digital loads through one serial interface. An I/O expander is an interface IC that increases the number of general-purpose digital input and output pins available to a host processor. The PCA9555BSHP occupies the level between a microcontroller and the discrete GPIO circuitry connected to it: the controller communicates over I2C or SMBus, while the expander converts eight register bits into eight outputs or reads back eight inputs. The integrated interrupt output reduces the need for continuous bus polling when an input changes state. Three hardware address pins, A0, A1, and A2, select the fixed I2C-bus address of the device. According to the NXP product page, as many as eight PCA9555 devices can share one bus when the address pins are configured differently. The PCA9555 also uses the same fixed bus address as the PCA9554, allowing the two device types to coexist on a bus in combinations that do not produce an address conflict. The 5.5 V maximum operating voltage and 400 kHz bus capability suit compact control boards, industrial modules, test equipment, and consumer accessories. The NXP part is identified with a 24-HVQFN exposed-pad package, which keeps the footprint compact while providing a thermal and electrical connection to the PCB ground plane. The exact exposed-pad construction and recommended land pattern should be taken directly from the manufacturer datasheet and package drawing. Designers should confirm the I2C pull-up resistance, address-strapping levels, output-drive requirements, and exposed-pad connection in the manufacturer datasheet. Because this device expands ports rather than providing level shifting, its VDD and VSS pins must match the logic environment used by the host and attached peripherals. Care is also required when connecting outputs to loads that source current independently.

RFQ צור קשר
PCA9555DB - 16-Bit I2C GPIO Expander with Interrupt | NXP
PCA9555DB

PCA9555DB - 16-Bit I2C GPIO Expander with Interrupt | NXP

The NXP Semiconductors PCA9555DB is a 16-bit I2C-bus and SMBus GPIO expander with interrupt, operating from 2.3 V to 5.5 V in a 24-pin SSOP package. It provides 16 general-purpose parallel input/output lines, supports 400 kHz serial operation, and uses an open-drain active-low interrupt output. What is an I2C GPIO expander? An I2C GPIO expander is an interface IC that adds parallel digital input and output capability to a controller with limited pins. The PCA9555 belongs to the I/O expander, parallel I/O, interface IC, and semiconductor hierarchy. Its two 8-bit ports connect a microcontroller or processor to switches, indicators, sensors, relays, and other external circuits while keeping the host-side connection compact. Key features include 16 configurable GPIO lines, separate input and output port registers, polarity inversion registers, 5 V tolerant I/O ports, and low standby-current consumption with a maximum of 1 uA. The 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V systems. Its open-drain interrupt output allows multiple change events to be combined on a shared host interrupt line. The device uses a two-wire I2C/SMBus interface with serial clock and serial data connections. A configurable seven-bit address supports multiple expanders on one bus, while 100 kHz and 400 kHz operating modes are identified in the provided NXP-family search data. The SSOP-24 package provides a conventional through-board surface-mount form factor with a 1.0 mm pitch. Typical applications include industrial control panels, programmable relay boards, LED status systems, keypad interfaces, sensor aggregation, and compact embedded control systems. The PCA9555DB is especially useful when a host controller needs more GPIO than its package or board-level pin budget can provide. Designers should confirm address selection, pull-up requirements, input thresholds, output-drive capability, and interrupt polarity against the manufacturer datasheet. Because the verified data does not include pricing or a complete pin-level table, those details remain explicitly unverified rather than inferred.

RFQ צור קשר
PCA9555DBR - 16-Bit I2C GPIO Expander with Interrupt | NXP (Tape & Reel)
PCA9555DBR

PCA9555DBR - 16-Bit I2C GPIO Expander with Interrupt | NXP (Tape & Reel)

The NXP Semiconductors PCA9555DBR is a 16-bit I2C-bus and SMBus GPIO expander with interrupt, operating from 2.3 V to 5.5 V in a 24-pin SSOP package. It provides 16 general-purpose parallel input/output lines, supports 400 kHz serial operation, and uses an open-drain active-low interrupt output. What is an I2C GPIO expander? An I2C GPIO expander is an interface IC that adds parallel digital input and output capability to a controller with limited pins. The PCA9555 belongs to the I/O expander, parallel I/O, interface IC, and semiconductor hierarchy. Its two 8-bit ports connect a microcontroller or processor to switches, indicators, sensors, relays, and other external circuits while keeping the host-side connection compact. Key features include 16 configurable GPIO lines, separate input and output port registers, polarity inversion registers, 5 V tolerant I/O ports, and low standby-current consumption with a maximum of 1 uA. The 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V systems. Its open-drain interrupt output allows multiple change events to be combined on a shared host interrupt line. The device uses a two-wire I2C/SMBus interface with serial clock and serial data connections. A configurable seven-bit address supports multiple expanders on one bus, while 100 kHz and 400 kHz operating modes are identified in the provided NXP-family search data. The SSOP-24 package provides a conventional through-board surface-mount form factor with a 1.0 mm pitch. Typical applications include industrial control panels, programmable relay boards, LED status systems, keypad interfaces, sensor aggregation, and compact embedded control systems. The PCA9555DBR is especially useful when a host controller needs more GPIO than its package or board-level pin budget can provide. Designers should confirm address selection, pull-up requirements, input thresholds, output-drive capability, and interrupt polarity against the manufacturer datasheet. Because the verified data does not include pricing or a complete pin-level table, those details remain explicitly unverified rather than inferred.

RFQ צור קשר