מוצרים (44,000+)

PCA9538PWR - 8-Bit I2C I/O Expander | NXP | TSSOP-16 (Tape & Reel)
PCA9538PWR

PCA9538PWR - 8-Bit I2C I/O Expander | NXP | TSSOP-16 (Tape & Reel)

The NXP Semiconductors PCA9538PWR is an 8-bit I2C-bus and SMBus general-purpose I/O expander with interrupt and reset, operating from 2.3 V to 5.5 V in a 16-pin TSSOP package. It adds eight remotely controlled digital input or output ports to a host microcontroller or processor while using the two-wire bus instead of dedicating eight GPIO pins. An I/O expander is an interface IC that extends a system’s digital input/output capability. The PCA9538 belongs to the hierarchy of GPIO expander, serial interface controller, and embedded peripheral. Its registers support configurable input, output, or high-impedance operation, while the interrupt output lets the host respond to selected port events without continuously polling all eight lines. Key features include eight general-purpose I/O lines, 2.3 V to 5.5 V operation, 400 kHz I2C/SMBus support, and dedicated interrupt and reset functions. The low-power design is useful in embedded control, sensor-interface, and power-management systems where a compact serial interface can replace several parallel host-controller pins. The device communicates through the two-line bidirectional bus using SCL and SDA. Its interrupt output provides event signaling, while reset provides a defined initialization path for the port and configuration state. These functions simplify firmware-driven GPIO expansion, particularly when the host must monitor external controls or remotely drive logic-level loads. Typical applications include ACPI power-switch control, sensor and actuator interfacing, push-button and indicator handling, and general embedded GPIO expansion. Designers should account for the selected port direction, pull-up requirements on SDA and SCL, and the electrical characteristics of every signal driven through the expander. For robust PCB implementation, place the serial-bus pull resistors close to the relevant bus nodes and keep the TSSOP routing short and clean. Review address configuration and firmware register access before operation, especially in systems with several I2C peripherals or multiple expanders on the same bus. This page consolidates the verified manufacturer and distributor information, separates confirmed specifications from data gaps, and provides practical design guidance for engineers evaluating PCA9538PWR. It also records sourced drop-in alternatives where the available evidence supports pin and package compatibility.

RFQ צור קשר
PCA9539BSHP - 16-Bit 400kHz I/O Expander | NXP
PCA9539BSHP

PCA9539BSHP - 16-Bit 400kHz I/O Expander | NXP

The NXP Semiconductors PCA9539BSHP is a 16-bit low-power I2C-bus and SMBus GPIO expander operating at up to 400 kHz in a 24-pin HVQFN package with a 4 x 4 mm body and exposed thermal pad. It provides 16 general-purpose input/output pins, an interrupt output, and a reset function for systems requiring more GPIO than the host controller can directly provide. An I2C GPIO expander is an interface IC that extends the input/output capacity of a host processor through a serial bus. The PCA9539BSHP belongs to the GPIO expander hierarchy, where serial I2C communication controls parallel digital ports. This approach reduces the number of pins required on a microcontroller, embedded system, or control board while allowing switches, LEDs, sensors, and other digital loads to connect through one bus. The device supports both 100 kHz and 400 kHz I2C operation. Its 16 I/O pins can be configured for digital input or output, while the interrupt and reset functions support event-driven host communication and orderly state recovery. The low-power design is particularly useful in embedded equipment where bus idle current, board area, and external wiring complexity are important design constraints. The PCA9539BSHP is a 24-pin CMOS device based on the NXP PCA9539 family of low-power I/O port expanders. It combines parallel GPIO capability with serial control and is designed for I2C-bus and SMBus applications. The HVQFN package also provides an exposed pad that can improve heat transfer when the device is mounted on a PCB with suitable copper and thermal layout. Typical uses include ACPI power-switch control, sensor interfaces, push-button inputs, status indicators, and fan or LED control. Its 16-bit port width makes it useful when several related digital signals must be grouped behind an I2C bus rather than connected individually to the host processor. A system designer can place the expander near the controlled peripherals and route compact serial signals back to the main controller. PCB design should preserve short I2C routing, common ground connectivity, and appropriate pull-up placement. The exposed thermal pad should be connected to the ground plane and thermal-via pattern specified in the NXP package documentation. Firmware must also configure each port direction, mask unwanted interrupts, and account for the device address and reset behavior before external signals are enabled. This product page combines the verified ordering information, functional characteristics, application guidance, package constraints, and replacement limitations for PCA9539BSHP. It also highlights where engineers should compare exact pin compatibility, bus address behavior, and power characteristics rather than treating every 16-bit I/O expander as a direct substitution.

RFQ צור קשר
PCA9539DB - 16-Bit I/O Expander, 2.3-5.5V | Texas Instruments
PCA9539DB

PCA9539DB - 16-Bit I/O Expander, 2.3-5.5V | Texas Instruments

Texas Instruments PCA9539DB is a 16-bit I2C/SMBus low-power I/O expander operating from 2.3 V to 5.5 V, supporting a 400 kHz bus and supplied in a 24-pin SSOP package. It adds 16 general-purpose parallel I/O lines to a host microcontroller through the two-wire serial bus. An I/O expander is an interface IC that extends the usable input/output count of a microcontroller or other embedded processor. It sits in the hierarchy of semiconductor, interface IC, I/O expander, and parallel I/O controller. Rather than requiring a microcontroller to devote many pins to switches, buttons, relays, or indicators, the PCA9539DB transfers those signals over I2C while providing configurable input and output registers. The PCA9539DB provides interrupt, reset, and configuration registers. Its interrupt output is open-drain and active-low, allowing the device to signal a change in an input state without continuous software polling. Maximum standby current is 1 µA, making the device suitable for low-power embedded systems that need additional control lines while minimizing inactive-state consumption. The device connects to a two-wire bidirectional I2C or SMBus interface and operates across a 2.3 V to 5.5 V supply range. This voltage range supports both 3.3 V and 5 V system architectures. The available 400 kHz bus specification provides a practical operating rate for control-oriented peripheral expansion where throughput requirements are modest and deterministic bus behavior is more important than maximum serial bandwidth. Typical uses include expanding GPIO on a compact embedded controller, reading grouped switch or sensor inputs, driving external indicator or relay-control signals, and building a modular peripheral interface around an I2C bus. The active-low open-drain interrupt is particularly useful when the host must sleep between events and wake when an input changes. Designers should account for I2C pull-up resistors, address selection, and the electrical requirements of whichever loads connect to P0 through P15. The PCA9539DB differs from the PCA9555 because it omits the internal I/O pull-up resistors, replaces the A2 address input with RESET, and uses a different address range. This reduced loading can lower power consumption when the I/O lines are held low, but external pull-ups may be required where the application depends on them. This product record consolidates the verified manufacturer and distributor information into an engineering-focused resource covering device function, package data, sourcing links, application context, and practical replacement constraints. Only confirmed drop-in alternatives with the same package and electrical behavior are presented; functional equivalents requiring a different footprint are not mislabeled as drop-in replacements.

RFQ צור קשר
PCA9539DBR - 16-Bit I/O Expander | Texas Instruments | 2.3-5.5V
PCA9539DBR

PCA9539DBR - 16-Bit I/O Expander | Texas Instruments | 2.3-5.5V

Texas Instruments PCA9539DBR is a 16-bit remote I2C and SMBus low-power I/O expander operating from 2.3 V to 5.5 V, with a 400 kHz bus rate, interrupt output, reset, and configuration registers in a 24-pin SSOP (DB) package. It adds 16 general-purpose input or output lines to a host controller without requiring a parallel GPIO port. An I/O expander is an interface IC that translates serial I2C or SMBus commands into parallel digital input and output signals. The PCA9539 belongs to the I/O expander class, within interface ICs and general-purpose semiconductor devices. Its purpose is to reduce microcontroller pin count while keeping peripheral control and monitoring accessible over a short two-wire serial bus. The PCA9539 provides 16 configurable I/O lines, 2.3 V to 5.5 V operation, and a maximum indicated bus speed of 400 kHz. The device also includes an interrupt output, reset support, and configuration registers. Texas Instruments describes the part as low power, and its operating temperature range is -40 °C to 85 °C for the DB package. Compared with the PCA9555, the PCA9539 removes the internal I/O pull-up resistors, replaces the A2 address input with RESET, and uses a different I2C address range. Removing the internal pull-ups can reduce current consumption when an I/O is held low, but it also requires the board designer to account for external pull-ups when the selected I/O configuration needs them. Typical uses include low-speed control-panel inputs, relay or indicator outputs, sensor and switch monitoring, keyboard-style matrix expansion, and general industrial-control systems. The serial interface is particularly useful when a controller must monitor or drive more discrete lines than its native GPIO count permits. The interrupt output can provide event-driven notification instead of continuous register polling. Designers should verify the complete DB-package pinout against the current manufacturer datasheet before PCB release. I2C bus rise time, pull-up resistance, pull-up voltage, input thresholds, output leakage, and the effect of the RESET pin must be checked in the target system. External pull-ups are particularly important because this variant does not include the PCA9555 family’s internal I/O pull-ups. This page consolidates the verified manufacturer and distributor information for PCA9539DBR, distinguishes the device from superficially similar PCA9555 and TCA9539 families, and identifies which replacement details require datasheet confirmation before a drop-in redesign.

RFQ צור קשר
PCA9539DW - 16-Bit 2.3-5.5V I/O Expander | Texas Instruments
PCA9539DW

PCA9539DW - 16-Bit 2.3-5.5V I/O Expander | Texas Instruments

The Texas Instruments PCA9539DW is a 16-bit I2C/SMBus I/O expander operating from 2.3 V to 5.5 V at up to 400 kHz, with interrupt, reset, and configuration registers in a 24-pin SOIC (DW) package. It adds 16 general-purpose serial I/O lines to a host microcontroller while minimizing package space and addressing requirements. An I/O expander is an interface IC that converts serial bus commands into parallel input or output signals. In the product hierarchy, the PCA9539 is an I/O expander, interface controller, peripheral IC, and semiconductor. It is especially useful when a microcontroller has too few pins for buttons, LEDs, relays, logic controls, or sensor-enable signals. Its I2C/SMBus connection allows the added lines to be controlled over two shared serial wires. The device provides 16 I/O pins, a 400 kHz bus clock, push-pull output capability, and low current consumption. According to the verified distributor data, output source and sink options include 10 mA and 25 mA configurations. The integrated interrupt output allows a connected processor to react to a change on an input without continuously polling the device, while reset and configuration registers support controlled startup and bus operation. The PCA9539 differs from the PCA9555 because it removes the internal I/O pull-up resistors, replaces address input A2 with RESET, and uses a different address range, as stated on the official TI product page. Removing the internal pull-ups can reduce power consumption when I/O lines remain low. The separate RESET function also provides a hardware reset path, although external pull-up or pull-down requirements must be verified against the complete electrical design. Typical uses include industrial control modules, sensor-interface boards, programmable logic controllers, remote I/O modules, instrumentation, and embedded systems requiring status LEDs, relay controls, or digital-input monitoring. The interrupt line can support efficient event-driven firmware, while the 16 parallel lines reduce the number of host-controller pins needed. Designers should confirm the 2.3 V to 5.5 V supply range, 400 kHz bus limit, I/O voltage levels, current limits, pull-up requirements, and address configuration in the manufacturer datasheet. External pull-ups on SDA and SCL and any required I/O pull resistors should be selected for the bus voltage, capacitance, and system noise environment. The host firmware should also verify register defaults before driving attached loads. This page combines verified manufacturer and distributor information, practical I/O-expander design guidance, and explicit data gaps for parameters not present in the supplied sources.

RFQ צור קשר
PCA9539DWR - 16-Bit 2.3-5.5V I/O Expander | Texas Instruments (Tape & Reel)
PCA9539DWR

PCA9539DWR - 16-Bit 2.3-5.5V I/O Expander | Texas Instruments (Tape & Reel)

The Texas Instruments PCA9539DWR is a 16-bit I2C/SMBus I/O expander operating from 2.3 V to 5.5 V at up to 400 kHz, with interrupt, reset, and configuration registers in a 24-pin SOIC (DW) package. It adds 16 general-purpose serial I/O lines to a host microcontroller while minimizing package space and addressing requirements. An I/O expander is an interface IC that converts serial bus commands into parallel input or output signals. In the product hierarchy, the PCA9539 is an I/O expander, interface controller, peripheral IC, and semiconductor. It is especially useful when a microcontroller has too few pins for buttons, LEDs, relays, logic controls, or sensor-enable signals. Its I2C/SMBus connection allows the added lines to be controlled over two shared serial wires. The device provides 16 I/O pins, a 400 kHz bus clock, push-pull output capability, and low current consumption. According to the verified distributor data, output source and sink options include 10 mA and 25 mA configurations. The integrated interrupt output allows a connected processor to react to a change on an input without continuously polling the device, while reset and configuration registers support controlled startup and bus operation. The PCA9539 differs from the PCA9555 because it removes the internal I/O pull-up resistors, replaces address input A2 with RESET, and uses a different address range, as stated on the official TI product page. Removing the internal pull-ups can reduce power consumption when I/O lines remain low. The separate RESET function also provides a hardware reset path, although external pull-up or pull-down requirements must be verified against the complete electrical design. Typical uses include industrial control modules, sensor-interface boards, programmable logic controllers, remote I/O modules, instrumentation, and embedded systems requiring status LEDs, relay controls, or digital-input monitoring. The interrupt line can support efficient event-driven firmware, while the 16 parallel lines reduce the number of host-controller pins needed. Designers should confirm the 2.3 V to 5.5 V supply range, 400 kHz bus limit, I/O voltage levels, current limits, pull-up requirements, and address configuration in the manufacturer datasheet. External pull-ups on SDA and SCL and any required I/O pull resistors should be selected for the bus voltage, capacitance, and system noise environment. The host firmware should also verify register defaults before driving attached loads. This page combines verified manufacturer and distributor information, practical I/O-expander design guidance, and explicit data gaps for parameters not present in the supplied sources.

RFQ צור קשר
PCA9539PW - 16-Bit I/O Expander | NXP Semiconductors
PCA9539PW

PCA9539PW - 16-Bit I/O Expander | NXP Semiconductors

NXP Semiconductors PCA9539PW is a 16-bit general-purpose I/O expander with I2C/SMBus connectivity, interrupt, and reset functions, designed for 2.3 V to 5.5 V operation in a 24-pin TSSOP package. It adds 16 configurable digital lines to a host controller while supporting both input and push-pull output operation. The verified distributor data identifies a 400 kHz bus and describes the device as a low-power remote I/O expander. An I/O expander is an interface IC that converts serial bus commands from a microcontroller or other host into multiple parallel digital signals. In the hierarchy, the PCA9539PW belongs to the I/O-expander class, then interface ICs, then semiconductor devices. Its purpose is to reduce direct GPIO requirements in systems that need many buttons, indicators, sensors, relays, or control lines while retaining a compact serial connection. The main feature set includes 16 general-purpose I/O lines, an interrupt output, reset support, configurable registers, and I2C/SMBus operation. The verified product description identifies the device as a 24-pin CMOS device with 16 GPIO expansion functions. Its 2.3 V to 5.5 V operating range supports both low-voltage and 5 V powered embedded systems, while the 400 kHz interface specification supports common embedded bus speeds. The interrupt and reset functions help the host avoid continuous polling when input lines change. Reset allows the host to initialize the device and its registers reliably, while the interrupt output provides an event indication for input changes. Because the exact pin names, electrical limits, and register details are not included in the supplied verified data, those values are not guessed in this record. Typical applications include ACPI power switches, sensor interfaces, push-button panels, LED indicators, and remote GPIO expansion for microcontrollers. The 16-bit organization makes it useful when a system needs more lines than a typical microcontroller package provides but does not require a large matrix keyboard or very high-current outputs. For PCB design, confirm the 24-pin TSSOP footprint and verify the bus voltage, pull-up requirements, address configuration, and pin mapping against the manufacturer datasheet before release. Do not assume that an electrically similar expander is a true drop-in replacement without checking every pin and electrical parameter. This page combines verified manufacturer and distributor descriptions, explicit data gaps, package information, application guidance, and drop-in replacement screening for the PCA9539PW.

RFQ צור קשר
PCA9539PW/Q900,118 - 16-Bit I2C GPIO Expander | NXP
PCA9539PW/Q900,118

PCA9539PW/Q900,118 - 16-Bit I2C GPIO Expander | NXP

The NXP PCA9539PW/Q900,118 is a 16-bit I2C-bus/SMBus GPIO expander with interrupt output and active-LOW reset, delivering 16 general-purpose I/O lines over a 400 kHz I2C interface in a 24-pin TSSOP (SOT361-1) package. An I/O expander is an interface IC that adds general-purpose input/output pins to a microcontroller or host processor through a serial bus such as I2C or SMBus. In the system hierarchy, it sits between the host MCU and peripheral circuitry - a power-management and interface component that relieves pin-constrained controllers of the burden of driving buttons, LEDs, switches, and sensors directly. Key features include 16 quasi-bidirectional GPIOs with 5 V tolerant I/Os, a polarity inversion register, an active-LOW open-drain interrupt output, and an external RESET pin that restores the default state without a bus power cycle. The /Q900 variant is qualified to AEC-Q100 for automotive applications and operates from 3.0 V to 5.5 V, versus 2.3 V to 5.5 V for the standard PCA9539PW. Architecturally, the PCA9539 is a CMOS slave device with four register pairs (input, output, polarity inversion, configuration) addressed via two hardware address pins A0 and A1, allowing four devices on one bus for up to 64 I/Os. Configuration registers set each pin as input (high-impedance) or output. The interrupt function flags any input state change for fast host polling, avoiding continuous bus reads. Typical applications include automotive body electronics (door modules, lighting control), keypad and switch scanning, LED drive expansion, server backplane monitoring, and industrial PLC I/O cards where MCU pin count is scarce. Design consideration: unused inputs should not be left floating; tie them to a defined level via the internal or external pull-up, and keep the I2C pull-up resistance sized for the 400 kHz bus load capacitance. This page synthesizes distributor pricing, drop-in alternatives from TI, Nexperia, and NXP standard-grade lines, plus design notes not found in the manufacturer datasheet.

RFQ צור קשר
PCA9539PWE4 - 16-Bit I2C I/O Expander | Texas Instruments
PCA9539PWE4

PCA9539PWE4 - 16-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCA9539PWE4 is a 16-bit I2C and SMBus low-power I/O expander operating up to 400 kHz, with interrupt and reset functions, housed in a 24-pin TSSOP package. The device expands a host controller's limited GPIO capability by providing 16 general-purpose input or output ports while retaining compact serial control over an I2C bus. An I/O expander is a peripheral interface integrated circuit that connects digital input and output lines to a serial bus. Its functional hierarchy is I/O expander, bus interface controller, interface IC, and semiconductor. The PCA9539 family uses the I2C or SMBus protocol for register-based configuration and data transfer, making it suitable where adding a second parallel I/O port would otherwise require additional host pins or a separate controller. The PCA9539PWE4 provides 16 individually configurable I/O lines, 400 kHz serial operation, interrupt output, hardware reset, and low-power behavior. Unlike the PCA9555, the PCA9539 removes the internal I/O pull-up resistors, reducing current consumption when outputs are held low. It also replaces the PCA9555 A2 address-control pin with RESET and uses a different device address range, so firmware and hardware address assignments must be reviewed carefully. The 24-TSSOP package measures approximately 4.40 mm in body width and uses gull-wing leads. The device is offered in an industrial temperature grade. Its two supply pins support separate core and I/O voltage domains, allowing the interface to operate across systems with different logic levels when the voltage relationship remains within the device's operating requirements. Typical uses include industrial controllers, programmable logic controllers, sensor and relay interfaces, keypad controllers, and embedded systems that need additional digital lines over a shared bus. The interrupt output allows the host to detect input changes without continuous register polling, helping reduce unnecessary serial activity. The RESET input provides a hardware mechanism for restoring the configurable registers to their default state. PCB implementation should preserve the 24-TSSOP footprint, pin-1 orientation, bus pull-ups, supply decoupling, and accessible reset and interrupt routing. Because the I/O pins lack internal pull-ups, external resistors may be required for open-drain bus signals or inputs that must maintain a defined state. Check the manufacturer pin-description table before assigning tracks or external pull-up networks. This product page combines the confirmed interface and package characteristics with practical implementation guidance, compatible-device comparisons, and design considerations for PCB layout, bus integrity, reset handling, and low-power I/O design.

RFQ צור קשר
PCA9539PWG4 - 16-Bit I/O Expander | Texas Instruments
PCA9539PWG4

PCA9539PWG4 - 16-Bit I/O Expander | Texas Instruments

The Texas Instruments PCA9539PWG4 is a 16-bit I2C/SMBus remote I/O expander operating from 2.3 V to 5.5 V, supporting bus speeds up to 400 kHz and packaged in a 24-pin TSSOP. The device provides 16 general-purpose input or output lines, an interrupt output, reset control, and configuration registers for compact peripheral expansion. An I/O expander is an interface IC that increases the number of digital input and output pins available to a host microcontroller. In the hierarchy of semiconductor devices, the PCA9539 belongs to the I/O expander class of interface controllers. It communicates with a host through the two-wire I2C or SMBus serial interface while driving or reading a separate group of 16 parallel I/O lines. This architecture reduces microcontroller pin count without requiring a high-speed parallel peripheral bus. The PCA9539 supports a 2.3 V to 5.5 V operating range and a maximum I2C/SMBus frequency of 400 kHz. Its 16 I/O channels can be configured through registers, while dedicated interrupt and reset functions simplify event-driven system design. The manufacturer product page identifies the device as a low-power SMBus I/O expander with interrupt, reset, and configuration registers. Unlike the closely related PCA9555, the PCA9539 does not include the internal I/O pull-up resistors. The absence of internal I/O pull-ups can reduce power consumption when output ports are held low. This behavior is useful in systems that provide their own pull-ups or use open-drain downstream circuitry. However, external pull-up resistors may be required where a defined input or bus state is needed. The RESET input provides a hardware mechanism for restoring the registers to their default configuration, while the interrupt output allows a host to respond when a configured input changes state. Typical uses include industrial control modules, sensor-hub boards, programmable logic controllers, communication equipment, and compact embedded systems that need more digital lines than the host controller provides. The 24-pin TSSOP package is also suitable for leaded, through-hole industrial assemblies where a surface-mount QFN package would be unsuitable. Designers should verify the exact I/O electrical limits, address options, and pin mapping in the manufacturer datasheet before finalizing a PCB. When implementing the PCA9539, place its pull-up components close to the bus master and keep the I2C routing away from high-current switching paths. Confirm that every port pin's input, output, pull-up, and current-limit requirements match the external circuit. Register programming should also account for the device's reset state and the timing relationship between reset release, bus communication, and the first port operation. This component guide combines device specifications, package guidance, application analysis, selection criteria, and verified drop-in alternatives. It also highlights the distinction between the PCA9539 and PCA9555 so engineers can select the correct expander when internal pull-ups, reset behavior, or address decoding affect the design.

RFQ צור קשר
PCA9539PWR - 16-Bit I/O Expander | NXP Semiconductors (Tape & Reel)
PCA9539PWR

PCA9539PWR - 16-Bit I/O Expander | NXP Semiconductors (Tape & Reel)

NXP Semiconductors PCA9539PWR is a 16-bit general-purpose I/O expander with I2C/SMBus connectivity, interrupt, and reset functions, designed for 2.3 V to 5.5 V operation in a 24-pin TSSOP package. It adds 16 configurable digital lines to a host controller while supporting both input and push-pull output operation. The verified distributor data identifies a 400 kHz bus and describes the device as a low-power remote I/O expander. An I/O expander is an interface IC that converts serial bus commands from a microcontroller or other host into multiple parallel digital signals. In the hierarchy, the PCA9539PWR belongs to the I/O-expander class, then interface ICs, then semiconductor devices. Its purpose is to reduce direct GPIO requirements in systems that need many buttons, indicators, sensors, relays, or control lines while retaining a compact serial connection. The main feature set includes 16 general-purpose I/O lines, an interrupt output, reset support, configurable registers, and I2C/SMBus operation. The verified product description identifies the device as a 24-pin CMOS device with 16 GPIO expansion functions. Its 2.3 V to 5.5 V operating range supports both low-voltage and 5 V powered embedded systems, while the 400 kHz interface specification supports common embedded bus speeds. The interrupt and reset functions help the host avoid continuous polling when input lines change. Reset allows the host to initialize the device and its registers reliably, while the interrupt output provides an event indication for input changes. Because the exact pin names, electrical limits, and register details are not included in the supplied verified data, those values are not guessed in this record. Typical applications include ACPI power switches, sensor interfaces, push-button panels, LED indicators, and remote GPIO expansion for microcontrollers. The 16-bit organization makes it useful when a system needs more lines than a typical microcontroller package provides but does not require a large matrix keyboard or very high-current outputs. For PCB design, confirm the 24-pin TSSOP footprint and verify the bus voltage, pull-up requirements, address configuration, and pin mapping against the manufacturer datasheet before release. Do not assume that an electrically similar expander is a true drop-in replacement without checking every pin and electrical parameter. This page combines verified manufacturer and distributor descriptions, explicit data gaps, package information, application guidance, and drop-in replacement screening for the PCA9539PWR.

RFQ צור קשר
PCA9541APW/01 - 2-to-1 I2C Master Selector, 16-TSSOP | NXP
PCA9541APW/01

PCA9541APW/01 - 2-to-1 I2C Master Selector, 16-TSSOP | NXP

The NXP PCA9541APW/01 is a 2-to-1 I2C-bus master selector with interrupt logic and reset, designed for high-reliability dual-master I2C-bus applications where system operation must continue even when one master fails or the controller card is removed for maintenance. It is housed in a 16-pin TSSOP (SOT403-1) package and supports 2 masters sharing a single downstream I2C bus, with channel 0 pre-selected at startup per the /01 variant. A 2-to-1 I2C master selector belongs to the broader family of I2C switches and multiplexers, which are themselves a subcategory of serial interface ICs used for digital inter-chip communication. The PCA9541APW/01 specifically enables bus-arbiter functionality by routing one of two upstream master controllers (e.g., a primary and a redundant back-up) onto a single downstream I2C bus segment. It sits between the master controllers and downstream peripherals, providing arbitration, fault isolation, and hot-swap capability. Key features include two upstream I2C channels (SCL0/SDA0 and SCL1/SDA1), one downstream I2C channel (SCL/SDA), an active-low RESET input, hardware-selectable channel at power-up via a startup mode pin, and bidirectional interrupt logic with separate INT0 and INT1 outputs that report which master currently controls the bus. The downstream INT_IN pin collects fault information from peripherals and propagates it upstream when enabled. The device operates from a supply voltage compatible with common 2.3V-5.5V rails and supports standard-mode and fast-mode I2C signaling. Its low on-resistance pass gates and channel-isolation logic keep bus capacitance low, ensuring clean rise/fall times even with long downstream traces. The PCA9541APW/01 variant pre-selects channel 0 at startup, while the /03 variant leaves no channel selected at startup - selection between /01 and /03 lets system designers tune the power-on behavior. Typical applications include redundant server backplanes with dual master controllers, fault-tolerant telecom equipment, hot-swappable controller cards, and industrial PLC systems where two CPUs arbitrate access to shared I2C peripherals. It is also used in RAID storage controllers and ATCA/AdvancedTCA shelf managers that require seamless master failover. When designing with this part, ensure pull-up resistors are present on the active upstream channel and the downstream bus, and follow the standard I2C impedance guidelines because the pass gates do not include internal pull-ups. Decoupling of VCC with a 100nF ceramic capacitor close to pin 16 is recommended. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet.

RFQ צור קשר
PCA9541APW/03112 - 2-to-1 I²C Master Selector w/ Interrupt | NXP
PCA9541APW/03112

PCA9541APW/03112 - 2-to-1 I²C Master Selector w/ Interrupt | NXP

The NXP PCA9541APW/03,112 is a 2-to-1 I²C-bus master selector with interrupt logic and reset, housed in a 16-pin TSSOP (PW) package. It operates from a supply voltage of 2.3 V to 5.5 V and provides bidirectional switching between two upstream I²C masters and a single downstream I²C bus, allowing either controller to access shared target devices such as EEPROMs, sensors, and ADCs. What is an I²C master selector? An I²C master selector is a type of bus switch that routes a single shared I²C bus between two (or more) upstream controllers. It sits in the I²C signal chain between the controllers (primary and back-up) and the target devices, behaving like a 1-of-2 multiplexer that is itself controlled by the masters over a separate selection line. Master selectors are commonly used for high-reliability redundant-controller applications where continuous operation must be maintained even when one master fails or is removed for maintenance. In the component taxonomy, the part belongs to: I²C switch -> bus switch -> interface IC -> integrated circuit -> semiconductor. Key features of the PCA9541A family include low standby current, integrated interrupt logic, hardware reset input, and wide 2.3 V to 5.5 V supply compatibility that covers both 3.3 V and 5 V rails. The device supports I²C and SMBus operations and provides bus recovery capability, which is critical when one master becomes unresponsive or the I²C bus is stuck low. Two upstream buses (BUS0, BUS1) connect through the selector to a single downstream bus (BUSX), and an external pull-up resistor pulls the open-drain SDAn/SCLn lines high on each side. The PCA9541APW/03,112 architecture centers on a 1-of-2 bidirectional switch realized with pass-gate MOSFETs and an I²C-compatible control interface. Two address-select pins (A0, A1) allow up to four PCA9541A devices to coexist on the same SMBus, enabling a 1-of-4 or 1-of-8 master selection tree. The reset input (/RESET) restores the selector to a defined default state on power-up or when the active-low signal is asserted by a system supervisor. Typical applications include redundant server management on baseboard management controllers (BMCs), telecom equipment with hot-swappable controller cards, fault-tolerant industrial PLCs, and any dual-master I²C architecture where the controller or a daughter card can be removed without disrupting downstream I²C target devices. Designers also use the part to bridge two electrically isolated I²C domains through a controlled switch. When designing with this device, note that both upstream buses require their own pull-up resistors to the selected supply, and the interrupt output is open-drain and must be pulled high at the system-controller side.

RFQ צור קשר
PCA9543AD - 2-Channel I2C Switch with Reset | NXP
PCA9543AD

PCA9543AD - 2-Channel I2C Switch with Reset | NXP

NXP Semiconductors PCA9543AD is a 2-channel bidirectional I2C-bus switch with interrupt logic and reset, operating from a 2.3 V to 5.5 V supply in a 14-pin SOIC package. It allows one upstream SCL/SDA pair to fan out to two downstream bus pairs, while the programmable control register independently enables either channel or both channels. Two active-low interrupt inputs support change detection on the downstream buses. An I2C-bus switch, also called an I2C multiplexer or I2C switch, is an interface IC that expands one controller-side bus connection into multiple target-side connections. In the product hierarchy, it belongs to the I2C interface-switch class, then to interface ICs, interface semiconductors, and broader semiconductor devices. This allows multiple devices with potentially conflicting addresses to share one physical I2C bus when their downstream ports are enabled selectively. The PCA9543AD provides two bidirectional translating channels compatible with I2C and SMBus systems. Its control register allows the upstream bus to communicate with channel 0, channel 1, or both channels. The device also includes a reset input and separate interrupt inputs for each downstream pair. These functions make it useful where downstream devices generate interrupts, wake a host controller, or must remain disconnected to prevent address conflicts. The switch's operating supply range of 2.3 V to 5.5 V accommodates both 3.3 V and 5 V system rails. Bidirectional communication is fundamental to I2C because the same SDA conductor carries command data from the controller and response data from targets, while SCL carries the clock in both directions. The package is a 14-pin SOIC measuring 0.154 inches, or 3.90 mm, in width, using a surface-mount construction. Typical uses include sensor aggregation, industrial embedded systems, communications equipment, portable electronics, and test or measurement platforms. In a multi-sensor design, the controller can enable one downstream branch at a time, communicate with the selected target, and disable that branch before accessing another device. Interrupt inputs can reduce the need for continuous polling when a downstream peripheral signals an event. Designers should verify the target's supported voltage range, bus capacitance, pull-up arrangement, and channel-isolation behavior against the manufacturer datasheet. Care is also required when connecting downstream buses with different pull-up voltages, because the switch does not inherently translate logic voltage levels. A common pitfall is assuming that a disabled channel provides complete galvanic isolation; it isolates the I2C data path but does not create independently regulated voltage domains. This product page consolidates the verified NXP device description, package information, source links, engineering-oriented application guidance, and explicitly qualified drop-in alternatives. Pricing and lead time remain unverified because the supplied distributor results did not expose numeric values, while alternative selection is limited to same-package devices that can be supported without inventing cross-reference data.

RFQ צור קשר
PCA9543ADR - 2-Channel I2C Switch with Reset | NXP (Tape & Reel)
PCA9543ADR

PCA9543ADR - 2-Channel I2C Switch with Reset | NXP (Tape & Reel)

NXP Semiconductors PCA9543ADR is a 2-channel bidirectional I2C-bus switch with interrupt logic and reset, operating from a 2.3 V to 5.5 V supply in a 14-pin SOIC package. It allows one upstream SCL/SDA pair to fan out to two downstream bus pairs, while the programmable control register independently enables either channel or both channels. Two active-low interrupt inputs support change detection on the downstream buses. An I2C-bus switch, also called an I2C multiplexer or I2C switch, is an interface IC that expands one controller-side bus connection into multiple target-side connections. In the product hierarchy, it belongs to the I2C interface-switch class, then to interface ICs, interface semiconductors, and broader semiconductor devices. This allows multiple devices with potentially conflicting addresses to share one physical I2C bus when their downstream ports are enabled selectively. The PCA9543ADR provides two bidirectional translating channels compatible with I2C and SMBus systems. Its control register allows the upstream bus to communicate with channel 0, channel 1, or both channels. The device also includes a reset input and separate interrupt inputs for each downstream pair. These functions make it useful where downstream devices generate interrupts, wake a host controller, or must remain disconnected to prevent address conflicts. The switch's operating supply range of 2.3 V to 5.5 V accommodates both 3.3 V and 5 V system rails. Bidirectional communication is fundamental to I2C because the same SDA conductor carries command data from the controller and response data from targets, while SCL carries the clock in both directions. The package is a 14-pin SOIC measuring 0.154 inches, or 3.90 mm, in width, using a surface-mount construction. Typical uses include sensor aggregation, industrial embedded systems, communications equipment, portable electronics, and test or measurement platforms. In a multi-sensor design, the controller can enable one downstream branch at a time, communicate with the selected target, and disable that branch before accessing another device. Interrupt inputs can reduce the need for continuous polling when a downstream peripheral signals an event. Designers should verify the target's supported voltage range, bus capacitance, pull-up arrangement, and channel-isolation behavior against the manufacturer datasheet. Care is also required when connecting downstream buses with different pull-up voltages, because the switch does not inherently translate logic voltage levels. A common pitfall is assuming that a disabled channel provides complete galvanic isolation; it isolates the I2C data path but does not create independently regulated voltage domains. This product page consolidates the verified NXP device description, package information, source links, engineering-oriented application guidance, and explicitly qualified drop-in alternatives. Pricing and lead time remain unverified because the supplied distributor results did not expose numeric values, while alternative selection is limited to same-package devices that can be supported without inventing cross-reference data.

RFQ צור קשר
PCA9543APW 2-Channel I2C Switch with Interrupt and Reset | NXP
PCA9543APW

PCA9543APW 2-Channel I2C Switch with Interrupt and Reset | NXP

The NXP Semiconductors PCA9543APW is a 2-channel I2C-bus switch with interrupt logic and reset, operating from 2.3 V to 5.5 V in a 14-pin TSSOP PW package. The device allows two independently controlled I2C target channels to connect to a common upstream bus, helping designers isolate unused devices, manage shared-bus addressing, and reduce unnecessary bus loading. It supports voltage translation, provides an interrupt output for downstream-device status monitoring, and includes a reset input for coordinated system startup. An I2C switch, also called an I2C bus switch or multiplexer, is an interface IC that routes serial data and clock lines between one controller-side bus and multiple downstream ports. In the hierarchy of electronic components, an I2C switch belongs to the interface-controller category, then to the broader interface IC and logic IC families. Its purpose is to make multiple compatible I2C peripherals easier to interconnect on a shared two-wire bus while preserving electrical and protocol compatibility. The PCA9543APW provides two switch channels, interrupt logic, and a reset function. Its 2.3 V to 5.5 V operating range supports both common low-voltage embedded systems and higher-voltage I2C environments. The TSSOP-14 surface-mount package is suitable for compact PCB layouts, while the interrupt and reset controls support systems requiring peripheral detection, fault recovery, or controlled power-up behavior. These characteristics make the device useful in embedded control, sensor networking, communications equipment, and general-purpose I2C expansion designs. Architecturally, the PCA9543APW separates the upstream SDA and SCL path from the two downstream channels. Downstream ports can be enabled or isolated according to system requirements, reducing loading and helping prevent unintended communication with devices that share the same bus. The interrupt function provides a hardware indication of activity on a downstream channel, allowing the host controller to service only the relevant peripheral. The reset input provides a common mechanism for returning the switch to a defined operating state during system initialization or recovery. Typical applications include I2C sensor aggregation, industrial monitoring modules, programmable power systems, communications equipment, and embedded controllers with multiple I2C peripherals. In a sensor-hub design, the upstream bus can remain connected while one downstream branch is isolated during reset or firmware updates. In a multi-domain instrument, the interrupt output can indicate that a downstream device has generated an event without requiring continuous polling of every branch. A key design consideration is ensuring that the selected channel states match the intended bus topology. Review the manufacturer pin and connection information before assigning SDA, SCL, reset, interrupt, and enable functions. Account for pull-up resistor placement, bus capacitance, voltage levels, and the power-up relationship between the controller and downstream devices. These checks are essential because the device can simplify routing while still requiring correct bus-level implementation. This product overview combines the manufacturer product information with practical design guidance, drop-in replacement context, pin and package details, and application-specific selection considerations. It is intended to help engineers evaluate the PCA9543APW for I2C bus isolation, voltage-level interfacing, and multi-peripheral system architectures without obscuring the important implementation trade-offs.

RFQ צור קשר
PCA9544AD - 4-Channel I2C Multiplexer with Interrupt | NXP
PCA9544AD

PCA9544AD - 4-Channel I2C Multiplexer with Interrupt | NXP

The NXP Semiconductors PCA9544AD is a discontinued 4-channel I2C-bus multiplexer with interrupt logic, packaged in a 20-pin SO package. The device connects one upstream SCL/SDA pair to four downstream SCx/SDx channel pairs, with only one downstream channel selected at a time through a programmable control register. It provides bidirectional translating multiplexed switch control for I2C and SMBus-compatible devices. An I2C-bus multiplexer, also called an I2C switch or channel selector, extends the practical reach of a shared two-wire bus by placing independently selectable devices behind one controller port. The PCA9544A belongs to the translating switch interface class, where the upstream SCL and SDA conductors fan out to four downstream conductors. Only the selected channel passes bus traffic, allowing several peripheral addresses to share one microcontroller or processor I2C port without simultaneous contention. The PCA9544A family includes interrupt logic, allowing downstream devices to request attention without the host repeatedly polling every bus segment. Channel selection and interrupt behavior are handled through the I2C control interface. The verified device information identifies a 2.3 V to 5.5 V operating range, four downstream I2C channels, bidirectional translation, interrupt logic, and a maximum power dissipation of 400 mW for the documented PCA9544APW,112 comparison variant. Typical uses include sensor aggregation, power-management controllers, EEPROMs, real-time-clock devices, and analog front ends that share one host I2C port. The multiplexer is particularly useful when one bus controller must reach four groups of peripherals, especially when the peripherals do not share a single usable address or require isolation to prevent unintended bus activity. Because the NXP product page states that PCA9544AD is no longer manufactured, new production designs should confirm availability and lifecycle status before committing to the footprint. Existing boards can generally preserve the SO-20 land pattern when substituting a verified PCA9544A-family device with matching logic, supply voltage, channel configuration, interrupt polarity, and address-selection behavior. A footprint match alone is not sufficient for a safe replacement. This page consolidates the verified manufacturer description, lifecycle status, distributor references, and documented PCA9544A-family alternatives into an engineering-focused view. It also distinguishes verified electrical facts from parameters that require confirmation against the NXP datasheet, preventing unsupported assumptions during redesign and end-of-life substitution work.

RFQ צור קשר
PCA9544ADW - 4-Channel I2C/SMBus Multiplexer | Texas Instruments
PCA9544ADW

PCA9544ADW - 4-Channel I2C/SMBus Multiplexer | Texas Instruments

Texas Instruments PCA9544ADW is a four-channel I2C and SMBus multiplexer with interrupt handling and voltage translation, supplied in a 20-pin SOIC (DW) package. It operates from a 2.3 V to 5.5 V supply and distributes one upstream SCL/SDA pair across four downstream SCx/SDx channel pairs. Only one downstream channel is selected at a time through the multiplexer's I2C control register. An I2C multiplexer is an interface IC that extends a shared two-wire bus to multiple peripheral branches while preventing signals from inactive branches from affecting the active branch. The PCA9544ADW belongs to the interface-controller hierarchy, connecting a host controller and several sensors, EEPROMs, amplifiers, or other I2C peripherals. Its translating architecture and interrupt inputs support systems in which attached devices require bus isolation or level translation. The principal functions are four-channel multiplexing, bidirectional voltage translation, and individual downstream interrupt inputs. Four interrupt lines allow a system controller to identify which selected peripheral asserted its interrupt signal. The device also consolidates control of channel selection through the upstream I2C bus, allowing firmware to change the active downstream path without rewiring hardware or mechanically switching buses. The translating design separates the upstream SCL/SDA pair from the four downstream SCx/SDx pairs. This arrangement provides electrical isolation between the host-side bus and each selected peripheral branch while retaining a compact 20-pin surface-mount implementation. The interrupt structure makes the device especially useful for mixed-signal, embedded, and sensor systems in which several downstream devices may request service from one shared controller. Typical uses include environmental and industrial sensor nodes, configuration registers accessed through EEPROM, portable measurement equipment, communication modules, and compact control boards that connect more I2C targets than the host bus can address directly. The PCA9544ADW is also appropriate when several embedded subsystems require controlled access to a common peripheral set. Designers should confirm the upstream and downstream voltage limits, pull-up requirements, channel-selection logic, and interrupt polarity in the manufacturer datasheet before committing a board layout. The SOIC footprint requires adequate lead spacing and process-control measures during assembly. PCB routing should keep SCL and SDA paths short, maintain continuous ground references, and avoid introducing bus-stub capacitance that could impair signal integrity. This product page combines the manufacturer identification, verified source links, structured technical characteristics, application guidance, and a qualified cross-manufacturer replacement assessment. It also distinguishes confirmed device functions from electrical details that must be established from the complete manufacturer datasheet before layout or production release.

RFQ צור קשר
PCA9544APW - 4-Channel I2C Switch | NXP | Embedded
PCA9544APW

PCA9544APW - 4-Channel I2C Switch | NXP | Embedded

The NXP Semiconductors PCA9544APW is a four-channel bidirectional I2C-bus translating multiplexer with interrupt logic, operating at up to 400 kHz and housed in a 20-pin TSSOP package. It allows one upstream SCL/SDA pair to fan out to four downstream SCx/SDx channel pairs while only one channel is connected at a time. An I2C-bus multiplexer is a switching interface that expands a single serial bus into multiple selectable downstream branches. It belongs to the interface IC hierarchy, where bus switches and multiplexers manage address, command, and data routing between a controller and multiple peripheral devices. Unlike a passive hub, this device provides controlled channel selection and bidirectional signal translation. The PCA9544APW includes four selectable downstream channels, interrupt logic for downstream alert signaling, and bidirectional upstream and downstream SCL/SDA connections. Its 400 kHz bus capability suits conventional I2C systems operating below the maximum Standard-mode frequency. The 20-pin TSSOP package supports compact PCB layouts in embedded control, industrial instrumentation, and consumer equipment. Channel selection is performed through the upstream I2C control interface. The active configuration determines which SCx/SDx pair is connected to the common SCL/SDA bus, allowing a controller to address devices on only one branch at a time. Interrupt logic provides a dedicated path for downstream events, helping the host detect activity without continuously polling every channel. Typical applications include sensor aggregation, programmable power supplies, EEPROM banks, communication interfaces, and industrial modules that place multiple devices behind one host bus. The four-channel architecture reduces the number of host GPIO pins and wiring connections required when peripheral addresses cannot all coexist on a single I2C segment. During layout, keep the upstream and selected downstream routing short, follow the datasheet recommendations for pull-up resistors, and account for bus capacitance when selecting the operating speed. Pull-ups should normally be placed according to the system-level I2C topology rather than duplicated on every downstream branch. This product page combines device functionality, verified source links, replacement guidance, application-specific design considerations, and parameter comparisons. These engineering details help distinguish a true same-package replacement from devices that merely perform a similar multiplexing function or require a different PCB footprint.

RFQ צור קשר
PCA9545ADW - 4-Channel I2C/SMBus Switch | Texas Instruments
PCA9545ADW

PCA9545ADW - 4-Channel I2C/SMBus Switch | Texas Instruments

The Texas Instruments PCA9545ADW is a four-channel bidirectional I2C and SMBus translating switch with interrupt logic, reset control, and voltage-level translation, housed in a 20-pin SOIC package. It supports a 2.3 V to 5.5 V operating range and allows one upstream controller to connect to as many as four downstream buses. The switch is controlled through the I2C interface and provides a compact way to isolate bus segments, expand bus capacity, and route controller signals to selected peripheral groups. An I2C or SMBus switch is an interface IC placed between a bus controller and one or more downstream buses. Its bidirectional translating channels can connect or disconnect selected branches while preserving the serial protocol, clock, and data signaling. The PCA9545A belongs to the broader switching IC, interface IC, and semiconductor hierarchy and is particularly useful when multiple devices share address space, require independent bus segmentation, or need controlled connection to reduce capacitive loading. The PCA9545A family provides four independently selectable downstream channels, interrupt logic, and a reset function. Voltage translation allows the device to bridge compatible buses operating at different logic levels within its stated 2.3 V to 5.5 V range. These functions support bus expansion, load isolation, address conflict management, and orderly recovery of downstream devices through the reset input. The manufacturer product page identifies the device specifically as a four-channel I2C and SMBus switch with interrupt, reset, and voltage translation. The switch is controlled through its I2C control port, while four bidirectional channel ports connect the upstream bus to downstream devices. Interrupt logic provides a consolidated indication when activity occurs on a selected downstream bus, and the reset input provides a common recovery mechanism for connected circuitry. Because the channels are bidirectional, each selected path can support command traffic from the controller and responses from remote devices. The PCA9545ADW ordering code specifies the surface-mount 20-SOIC package. Typical uses include separating multiple I2C sensor groups, expanding access to power-management devices, connecting an embedded controller to several low-power peripherals, and organizing a multi-device industrial or embedded system into separate bus branches. Interrupt support is useful in systems where the main processor should remain idle until a monitored downstream device needs attention. The reset function can help reinitialize devices after a bus fault, provided the system designer confirms that the reset signal and device power states meet the requirements of every connected component. PCB design should keep the upstream I2C traces short and route each downstream channel as a separate branch to avoid introducing unintended stubs. Pull-up resistors should be placed according to the bus topology and the voltage levels used on each segment. Confirm the address-selection behavior, interrupt polarity, reset timing, and logic-level compatibility of attached devices before finalizing the routing and component configuration. This product page combines the manufacturer’s device description with application guidance, pin and package references, practical design notes, and drop-in replacement candidates. It is intended to help engineers evaluate the PCA9545ADW for four-channel I2C or SMBus switching, interrupt handling, reset control, bus isolation, and voltage translation without treating packaging or board-layout compatibility as optional details.

RFQ צור קשר
PCA9545APW - 4-Channel I2C Switch with Interrupt | NXP
PCA9545APW

PCA9545APW - 4-Channel I2C Switch with Interrupt | NXP

The NXP Semiconductors PCA9545APW is a 4-channel bidirectional I2C-bus switch with interrupt logic and reset, packaged in a 20-pin TSSOP (PW) package. A single upstream SCL/SDA pair fans out to four downstream SCL/SDA channel pairs, and every channel can be individually enabled or deselected by the contents of the programmable control register. An I2C bus switch (also called an I2C multiplexer or bus router) is a level-transparent pass gate that expands one physical I2C bus into several independent downstream buses. Within the component hierarchy it sits below the system bus controller, above the individual I2C target devices, and belongs to the wider family of interface ICs that manage serial bus arbitration, addressing and clock and data distribution. Key features of the PCA9545A include four independent downstream channel pairs (SC0/SD0 through SC3/SD3), four interrupt inputs INT0 to INT3 with one input per downstream pair, an active-LOW RESET input, and an internal power-on reset function. Any individual channel, or any combination of channels, may be selected. Channel selection and the interrupt and reset behaviour are controlled entirely from the upstream side of the bus. Architecturally the device uses bidirectional translating pass gates between the upstream bus and each downstream channel, so data can flow in either direction on SCL and SDA without level shifting of the logic thresholds themselves. The interrupt inputs allow a host microcontroller to be notified when a downstream target pulls its data line LOW, and the active-LOW reset input lets the system recover a downstream bus that has been held LOW by a stalled or disconnected target. Typical applications include sensor node fan-out where several identical I2C sensors share one host port, interrupt-driven industrial acquisition systems, battery management systems with per-cell current monitors, server and storage module EEPROM sharing, wearable medical monitoring accessories, and multi-channel programmable LED driver control. When laying out the board, remember that each downstream channel is a separate bus segment and therefore needs its own pull-up resistor pair; do not assume the upstream pull-ups will serve all four channels. Tie RESET to a defined level with a pull-up or a host GPIO, and keep the unused channels tied to a defined state so that a floating downstream segment cannot be pulled into an unexpected state during power-up. This page consolidates the NXP product documentation, distributor listings, cross-reference candidates, application patterns and practical layout guidance for the PCA9545APW into a single engineering reference.

RFQ צור קשר
PCA9545D/G-T 4-Channel I2C Switch | NXP | 20-SOIC
PCA9545D/G-T

PCA9545D/G-T 4-Channel I2C Switch | NXP | 20-SOIC

NXP PCA9545D/G-T is a four-channel I2C bus switch with interrupt logic and reset, designed for routing a shared controller bus among multiple downstream targets. It operates from the 2.3 V to 3.6 V and 4.5 V to 5.5 V supply ranges and is packaged in a 20-pin SOIC measuring 0.295 inch, or 7.50 mm, in width. Its principal function is to isolate inactive bus segments, reduce loading, and allow multiple I2C devices to share limited address space without requiring a separate controller for every target. An I2C switch is an interface IC that extends a two-wire serial bus by connecting or disconnecting selected downstream branches. The PCA9545D/G-T belongs to the I2C interface switch category, interface IC hierarchy, and broader digital semiconductor family. It provides four independently selectable downstream channels so embedded systems can route sensors, memory devices, display controllers, or other peripherals. The integrated interrupt logic reports selected channel activity, while reset provides a controlled way to initialize the switching and selection logic. The primary benefits are flexible bus partitioning, reduced capacitive loading, and improved organization of multi-device systems. Each downstream path can be enabled only when required, helping isolate inactive devices. The 2.3 V to 3.6 V range supports low-voltage systems, while the 4.5 V to 5.5 V range accommodates conventional 5 V equipment. These two listed operating ranges make the device suitable for mixed-voltage interface architectures when the connected devices and level translation arrangement are appropriately designed. Technically, the PCA9545D/G-T functions as a controlled connectivity matrix between one upstream I2C bus and four downstream branches. When a channel is disconnected, the corresponding downstream bus is prevented from loading the common bus. When enabled, transactions can propagate toward the selected target. Interrupt logic supports event-driven handling by the host processor, reducing unnecessary polling, while the reset input allows the system to restore a known selection state during startup or fault recovery. Typical uses include sensor aggregation, industrial control modules, medical monitoring equipment, communications equipment, rack-mounted systems, and embedded consumer products. A host processor can connect several low-speed peripherals that have overlapping or conflicting addresses, then activate only the required branch. This arrangement preserves I2C wiring simplicity while controlling bus capacitance and limiting unwanted communication between disconnected targets. PCB design should preserve short, clean I2C traces and place pull-up resistors where the bus topology requires them. Keep the reset and interrupt traces away from high-current switching nodes, provide a stable local supply rail, and verify that every enabled channel stays within the device's specified capacitance and timing limits. Confirm voltage compatibility across all attached targets before sharing a bus. This product page combines the exact NXP ordering designation, package information, operating ranges, sourcing status, and supported interface functions with practical selection guidance, application analysis, and a parameter-focused comparison framework. It is designed to help engineers identify the correct channel count, package, voltage range, and system role before integrating the device into a new board or revising an existing multi-device I2C design.

RFQ צור קשר
PCA9546AD - 4-Ch I2C Switch with Reset, SOIC-16 | NXP
PCA9546AD

PCA9546AD - 4-Ch I2C Switch with Reset, SOIC-16 | NXP

The NXP Semiconductors PCA9546AD is a quad bidirectional translating I2C-bus and SMBus switch with reset function, housed in a 16-pin SOIC (SO16) surface-mount package. It operates from a 2.3V to 5.5V supply, supports bus speeds up to 400 kHz, and fans out one SCL/SDA upstream pair to four downstream SCn/SDn channel pairs selected via a programmable control register. An I2C switch (also called an I2C multiplexer or I2C bus expander) is an interface IC that sits between a master controller and multiple I2C slave buses. It belongs to the broader hierarchy of I2C bus hub devices within the interface IC family, resolving address conflicts and allowing one controller to manage more devices than a single bus can address, while also isolating capacitive loading per segment. Key features of the PCA9546AD include an active-LOW RESET input that recovers the switch to its default state (all channels deselected) if the I2C bus hangs, four selectable or simultaneously selectable channels determined by the writable control register, and pass-gate translation architecture that allows 1.65V-to-5.5V logic-level translation between low-voltage masters and higher-voltage slaves. The pass-gate switch topology keeps the downstream channel capacitance isolated from the upstream bus until a channel is enabled, reducing total bus capacitance and improving rise times. The control register powers up in a known default state, and the RESET pin allows the system master to recover from bus lockup conditions caused by a slave holding SDA low. Typical applications include multiplexing I2C sensors in industrial automation, expanding address space in server and storage backplanes, connecting multiple camera or display modules in consumer electronics, and isolating fault-prone slave segments in automotive body-electronics networks. A critical design consideration: with any channel enabled, the pass-gate series resistance adds to the bus, so keep pull-up resistor values low enough to meet rise-time requirements at 400 kHz, especially with multiple channels enabled simultaneously. This page synthesizes distributor sourcing data, drop-in alternatives including the Texas Instruments PCA9546A equivalent, and practical design notes not found in the manufacturer datasheet. Per the NXP product page, the PCA9546AD is marked End of Life, so lifecycle planning and second-source qualification are strongly recommended.

RFQ צור קשר
PCA9546AD,118 - 4-Ch I2C Bus Switch Reset | NXP | SOIC-16
PCA9546AD,118

PCA9546AD,118 - 4-Ch I2C Bus Switch Reset | NXP | SOIC-16

The NXP PCA9546AD,118 is a 4-channel bidirectional I2C-bus and SMBus translating switch with active-LOW reset, operating from 2.3 V to 5.5 V supply in a 16-pin SOIC (0.154 in, 3.90 mm width) package. A single SCL/SDA upstream pair fans out to four downstream SCx/SDx channel pairs, selectable individually or in any combination via the programmable control register. An I2C multiplexer (bus switch) is an interface IC that solves address-conflict and bus-capacitance problems in I2C systems. In the interface IC hierarchy (I2C switch -> bus multiplexer -> I2C controller peripheral -> interface IC), it sits between a master controller and multiple I2C slave buses, allowing the master to isolate or connect downstream segments on demand. Multiplexing also lets two devices sharing the same slave address coexist on separate channels. Key features include four bidirectional translating switch channels, I2C and SMBus compatibility, three hardware address pins (A0, A1, A2) allowing up to eight PCA9546A devices on one bus, and an active-LOW RESET input that recovers the switch to the all-channels-deselected state if the bus hangs. On power-up all channels are deselected, guaranteeing a deterministic bus state. Low on-resistance pass-gate switches preserve signal integrity for standard-mode and fast-mode I2C traffic. Architecturally, the PCA9546A uses a write-only control register addressed at one of eight I2C addresses set by the A0-A2 pins; the register byte directly maps bits D0-D3 to channels 0-3. Because the pass-gate switches are bidirectional and voltage-translating, upstream and downstream segments may run at different logic levels within the 2.3-5.5 V supply envelope. Maximum power dissipation is rated at 400 mW. Typical applications include multiple sensor or EEPROM buses in industrial automation, camera and display module selection in consumer electronics, and isolating slow or fault-prone slave devices from a shared system management bus (SMBus/PMBus topologies). Design consideration: place the RESET pin pull-up close to the device and use 1-10 kOhm pull-ups on SDA/SCL per bus segment; note that the control register is write-only and the RESET input is the only hardware recovery path. This page synthesizes distributor pricing, drop-in alternatives, pinout detail, and practical design notes not consolidated in the manufacturer datasheet. Note: the NXP product page lists PCA9546AD as End of Life (EOL); plan second-source qualification accordingly.

RFQ צור קשר