מוצרים (44,000+)

PCA9616PW - 3-Channel Differential I2C Bus Buffer | NXP
PCA9616PW

PCA9616PW - 3-Channel Differential I2C Bus Buffer | NXP

The NXP Semiconductors PCA9616PW is a dual-supply, 3-channel multipoint Fast-mode Plus (Fm+) differential I2C-bus buffer with hot-swap logic, packaged in a 16-pin TSSOP (PW) surface-mount package. It buffers the single-ended SMBus/I2C-bus up to 1 MHz and converts it to a differential I2C (dI2C) bus that reliably extends communication through electrically noisy environments over cable runs of at least 3 meters, or longer at reduced clock speeds. A differential I2C-bus buffer, sometimes called a bus repeater or redriver, is an interface IC that belongs to the signal buffer family within the broader hierarchy of interface integrated circuits. Where a plain I2C bus uses open-drain single-ended lines vulnerable to ground bounce and common-mode noise, a dI2C buffer translates the bus into a differential current-mode signaling scheme, dramatically improving common-mode noise immunity while remaining fully compatible with existing Standard-mode, Fast-mode, and Fast-mode Plus I2C and SMBus devices. Key features of the PCA9616PW include its 3-channel multipoint architecture, which supports a dI2C bus shared by multiple nodes for multipoint topologies; its dual-supply design isolating the single-ended side from the differential side; support for Fast-mode Plus operation at 1 MHz; and integrated hot-swap logic that allows a card or module to be inserted into or removed from a live backplane without corrupting bus transactions. Signal direction is fully automatic, requiring no external direction-control signal. Technically, the device pairs each single-ended SDA and SCL line with differential transmit/receive pairs on the cable side, using current-mode differential drivers and receivers with high common-mode noise rejection. Because it is a multipoint buffer, several PCA9616 devices can share one differential cable, enabling distributed systems such as rack-mounted cards, industrial backplanes, and remote sensor clusters. NXP documents cable extension of at least 3 m, with longer runs achievable at lower bus speeds. Typical applications include industrial backplane I2C distribution, telecom and server shelf management, multipoint sensor networks in electrically noisy factory environments, and hot-pluggable module bus extension. The hot-swap logic makes it especially suitable for field-replaceable cards. Design consideration: plan the differential bus topology to respect multipoint stub-length limits, and verify supply sequencing on both the single-ended and differential rails against the manufacturer datasheet to guarantee correct hot-swap behavior. This page synthesizes distributor pricing, drop-in replacement analysis, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
PCA9618UKZ - Single-Channel Fm+ I2C Bus Repeater | NXP
PCA9618UKZ

PCA9618UKZ - Single-Channel Fm+ I2C Bus Repeater | NXP

NXP Semiconductors PCA9618UKZ is a single-channel CMOS repeater for Fast-mode Plus I2C-bus or SMBus signals, with a 4-WLCSP package measuring 0.83 mm by 0.78 mm. It can buffer either the SCL clock line or the SDA data line, and it also supports single-bit buffering applications. An I2C bus repeater is an interface IC that regenerates a digital communication signal between a bus controller and a downstream device. Repeaters extend usable bus distance, isolate capacitive loading, improve signal integrity, and allow separate bus segments to operate at compatible logic levels. In the broader semiconductor hierarchy, the PCA9618UKZ is a bus repeater, then an interface IC, then an integrated circuit and semiconductor. The principal benefit of the PCA9618UKZ is its combination of Fm+ I2C or SMBus compatibility, one-bit architecture, and compact WLCSP-4 footprint. The small package supports placement close to a connector, bus branch, or device interface. Its single-channel format also allows designers to add buffering where required rather than fitting a multi-channel device that would remain unused. The device is intended for separating clock and data paths when capacitive loading, bus extension, or signal-integrity constraints become important. In a typical implementation, the incoming side connects to the host or bus master, while the output side drives a downstream peripheral. The buffered path reduces the electrical loading seen by the source while maintaining the logic signaling required by I2C-compatible devices. Typical uses include sensor networks, industrial controllers, consumer equipment, communications modules, and compact embedded systems that use I2C or SMBus. The device is also suitable for generic single-bit level translation or buffering where the system requires regenerated logic rather than a multi-channel fixed-direction translator. Designers should place the repeater near the branch or load that requires isolation, verify timing margins at the intended bus rate, and account for package parasitics and board-level capacitance. The 4-WLCSP footprint also demands careful PCB layout, stencil and reflow control, and inspection because its ball pitch and dimensions leave little room for rework. This page consolidates the confirmed function, package information, sourcing details, interface considerations, and drop-in replacement status of the PCA9618UKZ. It also distinguishes verified device facts from electrical parameters that engineers must confirm in the NXP product specification before finalizing a design.

RFQ צור קשר
PCA9621D - 8-Bit 65mA I/O Expander | NXP | LED Drive
PCA9621D

PCA9621D - 8-Bit 65mA I/O Expander | NXP | LED Drive

The NXP Semiconductors PCA9621D is an 8-bit I/O expander with a 65 mA output sink capability, configurable from a 2-wire bus interface in a 16-pin SOIC package. It supports I2C-bus and SMBus control, while the manufacturer also describes compatibility with PMBus and similar serial-bus systems. An I/O expander is an interface IC that adds independently controlled digital outputs to a host processor. The PCA9621D belongs to the broader serial-interface controller hierarchy: it receives register writes over a 2-wire bus and converts those commands into eight configurable output-port states. This architecture reduces the number of GPIO pins required by a host and makes it useful when an embedded controller needs additional discrete output drive. The primary headline specifications are an 8-bit output port, 65 mA sink capability per device output, and operation from a 2-wire serial interface with support for I2C and SMBus. Its 16-SO package supports compact surface-mount PCB layouts. The output state is held in a programmable 8-bit register that the host can read and write through the serial interface. Each output can be treated as a general-purpose logic output rather than being limited to a conventional LED-driver function. The NXP product page specifically identifies the 65 mA sink capability as suitable for driving LEDs, while the general-purpose output architecture also supports relay, indicator, or logic-level signaling where the electrical limits are respected. The serial interface allows the host microcontroller to update output patterns without dedicating eight separate GPIO pins. Typical uses include status and indicator LED banks, alarm and warning lamps, industrial annunciation panels, lighting-control modules, and embedded systems with limited GPIO availability. A microcontroller or other 2-wire-bus controller writes the desired output pattern to the PCA9621D, and the device presents the corresponding states at its eight outputs. A device such as the PCA9621D can therefore consolidate repetitive indicator or lamp control into one serial interface. The principal design considerations are the absolute output current limit, the voltage levels accepted by the attached loads, and correct I2C or SMBus implementation. Each load path and output driver must remain within the device's stated 65 mA sink capability, while the PCB must provide adequate copper and thermal margin for the selected duty cycle. The manufacturer datasheet should be used for the complete pin description, electrical limits, timing information, and recommended application circuit. This page organizes the manufacturer specifications, purchasing information, application guidance, and pin-level design considerations for engineers evaluating the PCA9621D. It also provides a comparison framework for evaluating other 8-bit, 2-wire output-port devices against package, interface, output-current, and functional requirements.

RFQ צור קשר
PCA9641PWJ - 2-Channel I2C Bus Arbiter | NXP
PCA9641PWJ

PCA9641PWJ - 2-Channel I2C Bus Arbiter | NXP

The NXP Semiconductors PCA9641PWJ is a 2-channel I2C bus controller arbiter and 2-to-1 master demultiplexer packaged in a 16-pin TSSOP. It is designed for dual-controller I2C systems in which two bus masters may issue commands simultaneously. The arbitration function selects one controller as the winner, allows that controller to operate without interruption, and enables the losing controller to take control when arbitration is required. An I2C controller arbiter is a specialized interface IC that manages competing requests to use a shared two-wire bus. The broader hierarchy is I2C controller arbiter, I2C bus interface, interface IC, semiconductor, and electronic component. Unlike a conventional I2C bus switch or channel multiplexer, the PCA9641 is specifically intended to arbitrate between two master controllers while also routing commands through a 2-to-1 master demultiplexer. The manufacturer identifies the PCA9641 as a 2-to-1 I2C master demultiplexer with an integrated arbiter function. Its principal role is high-reliability dual-master operation: the arbiter elects a winning master and prevents simultaneous masters from interfering with one another. The losing master can subsequently assume control of the shared I2C bus when the winning master releases it. This behavior is useful where deterministic bus ownership is needed more than simply routing separate I2C branches. Typical PCA9641PWJ applications include redundant or alternate industrial controllers, dual-processor instrumentation, embedded test equipment, controller isolation in complex electronics, and systems in which two embedded masters share access to the same peripheral bus. The device helps centralize command arbitration close to the I2C domain, reducing the need for firmware-level coordination during simultaneous access attempts. The PCA9641PWJ is identified by NXP as a 16-TSSOP device, and distributor listings classify it as a two-channel buffer and multiplexer. Because arbitration behavior depends on the complete circuit, designers should follow the manufacturer datasheet for pin assignments, electrical limits, operating conditions, timing, and recommended application wiring rather than relying on generic I2C-switch schematics. For PCB implementation, place the device close to the controlled I2C segment, route clock and data traces as a matched pair, and keep the arbitration inputs, master request signals, and bus connections away from noisy switching stages. The 16-pin TSSOP footprint supports compact designs, but power, ground, and signal-integrity requirements should be checked against the latest NXP documentation before layout release. This page organizes the exact product identity, manufacturer documentation, package information, application context, and verified replacement information for PCA9641PWJ. It also distinguishes true drop-in candidates from parts that are only functionally similar, helping engineers assess PCB reuse without assuming that equivalent bus-routing functions guarantee identical pin compatibility.

RFQ צור קשר
PCA9661B - 3.3V I2C Bus Controller | NXP | LQFP-48
PCA9661B

PCA9661B - 3.3V I2C Bus Controller | NXP | LQFP-48

The NXP Semiconductors PCA9661B is a 3.3 V I2C parallel-interface bus controller designed for data-intensive I2C transfers. It is offered in a 48-LQFP package measuring 7 mm by 7 mm and operates across the -40°C to 85°C temperature range. The device provides one I2C-bus channel and uses parallel interface logic to connect a host-side parallel bus with external serial peripherals. An I2C-bus controller is an interface IC that manages transactions between a parallel processor or bus master and devices connected through the two-wire I2C interface. In the broader semiconductor hierarchy, the PCA9661B belongs to the I2C controller class, which falls under interface controllers and then general-purpose interface ICs. Its role is to translate parallel data, control signaling, and bus timing into serialized I2C transfers for displays, sensors, memory devices, communications modules, and other peripheral ICs. NXP describes the PCA9661 as an advanced, fourth-generation, single-leader-mode bus controller. The B revision is identified in the product information as a single-master or single-leader I2C controller. Its architecture is intended to support dense systems where a processor-side parallel interface must service multiple I2C destinations efficiently. Parallel-to-serial bus management can reduce repetitive software transactions by centralizing addressing, control, and status handling in dedicated hardware. The 3.3 V operating supply matches many contemporary embedded processors, application processors, programmable logic devices, and communication controllers. This makes the PCA9661B useful in industrial controllers, test equipment, embedded computing platforms, communications infrastructure, and data-acquisition systems that already operate from a 3.3 V rail. Designers should confirm signal levels, timing limits, supported operating modes, and exact register behavior against the manufacturer datasheet before finalizing a new design. The 48-LQFP package exposes 48 leads, but its 1.4 mm package height does not by itself determine minimum PCB pad geometry. Follow the NXP land-pattern and stencil recommendations, including exposed-pad and soldering details shown for the selected orderable variant. Account for signal propagation between the parallel interface and the I2C pins, and place pull-up and bus-capacitance components where they can maintain a short return path. NXP marks the PCA9661B as not recommended for new designs and identifies PCA9665APW as its recommended replacement. Existing installations may continue to use the PCA9661B for maintenance or design continuity, but new products should evaluate the recommended NXP successor and confirm whether its package, pinout, registers, voltage limits, timing, and thermal characteristics permit a direct PCB substitution. The PCA9665APW is not represented here as a drop-in alternative because the available product information does not establish pin-to-pin and package equivalence. This page organizes the verified product identity, lifecycle guidance, electrical limits, package details, design considerations, replacement analysis, and application guidance. It distinguishes confirmed manufacturer information from parameters that still require direct review of the datasheet, helping engineers separate verified device facts from assumptions before schematic capture, PCB layout, or production sourcing.

RFQ צור קשר
PCA9663B - 3-Channel Fm+ I2C Controller | NXP | LQFP-48
PCA9663B

PCA9663B - 3-Channel Fm+ I2C Controller | NXP | LQFP-48

NXP PCA9663B is a parallel-bus to three-channel I2C-bus controller supporting data rates up to 1 Mbit/s through Fast-mode Plus open-drain channels, packaged in a 48-LQFP 7 x 7 mm package. The device operates from a 3.3 V supply, includes three independent I2C channels, and provides a 4352-byte data buffer per channel for data-intensive serial transfers. An I2C-bus controller is an interface IC that converts parallel host-bus transactions into serial I2C commands and manages the timing, addressing, and data transfer protocol. The PCA9663B belongs to the parallel-bus-to-I2C-controller segment of the interface IC hierarchy, where it connects a conventional microprocessor or host bus with multiple I2C peripherals. Its three-channel architecture allows separate serial buses to operate independently rather than sharing one serialized channel. Key features include Fast-mode Plus operation, 1 Mbit/s maximum data rate, 30 mA SCL and SDA sink-current capability, and an internal oscillator trimmed to 1% accuracy. The generous 4352-byte buffer on each channel reduces host-service overhead during sustained transfers. These characteristics make the controller useful when a system must move blocks of sensor, display, communications, or configuration data over I2C without tying up the host on every byte. The PCA9663B is designed for data-intensive parallel-to-serial conversion. Each channel uses the standard open-drain Fm+ topology, allowing the bus lines to be pulled up externally as required by the system voltage and capacitance. The internal trimmed oscillator removes the need for an external precision timing component, while independent channel state supports simultaneous work on multiple bus domains. Configuration registers and command handling are managed through the parallel host interface. Typical applications include industrial sensor aggregation, programmable logic or microcontroller peripheral expansion, multi-channel display or control systems, telecommunications equipment, and embedded data-acquisition platforms. Three independent channels can support groups of sensors, memory devices, or transceivers while isolating their traffic. The 1 Mbit/s rate is appropriate for high-volume configuration and monitoring data without moving control traffic to a much faster parallel or serial interface. PCB design should preserve short, clean SCL and SDA routing, provide the required pull-up resistors, and place decoupling capacitors close to the supply pins. Because the external pull-up value affects rise time and bus timing, it should be selected from the actual board capacitance and the Fm+ requirements. Review the manufacturer's pin and connection guidance before assigning host-bus signals or laying out the three I2C channels. This product page combines the manufacturer's core electrical and architecture information with package details, sourcing workflows, selection guidance, and practical implementation considerations. It is designed to help engineers determine whether the PCA9663B matches the required channel count, transfer rate, buffering, voltage, and LQFP-48 footprint before beginning PCB design.

RFQ צור קשר
PCA9665D - Fm+ Parallel to I2C Controller | NXP | 20-SO
PCA9665D

PCA9665D - Fm+ Parallel to I2C Controller | NXP | 20-SO

The NXP PCA9665D is an Fm+ parallel-bus to I2C-bus controller packaged in a 20-pin SOIC. It is designed for systems in which a parallel processor or programmable logic device must communicate with I2C peripherals. The controller provides a structured bridge between a parallel host interface and the serial I2C bus, reducing the firmware and wiring burden associated with bit-level I2C transactions. Its nominal supply range is 2.5 V to 3.3 V, and the device consumes approximately 100 uA of supply current. An I2C bus controller is an interface IC that converts commands and data from a parallel or processor-specific bus into transactions on an I2C serial bus. The I2C interface uses SDA for bidirectional data and SCL for the clock, while the parallel side communicates with a host using a dedicated address and data register arrangement. This device family is useful when a controller, display subsystem, communications equipment, or embedded logic platform needs to access low-speed I2C peripherals without using an I2C-capable host controller. The PCA9665D is identified by NXP as an Fm+ parallel bus to I2C-bus controller. Its 20-pin SOIC package supports conventional surface-mount assembly and provides a practical upgrade path for designs that require a dedicated parallel-to-I2C bridge. The 2.5 V to 3.3 V operating range is compatible with low-voltage digital systems, while the approximately 100 uA supply current is important in equipment where the interface must not create an unnecessary standing load. Detailed clock, addressing, electrical, and timing limits should be taken from the manufacturer datasheet. Typical uses include industrial control panels, programmable-logic-based peripherals, test systems, communication modules, display-control boards, and embedded equipment that exposes an I2C bus through a parallel host interface. The PCA9665D is especially useful when the existing host processor does not provide a suitable I2C peripheral. In such designs, the parallel interface can be connected to external logic or a processor bus, while the I2C side reaches sensors, EEPROMs, expanders, and other compatible devices. When laying out a replacement design, verify the exact package variant, supply voltage, address behavior, clock timing, and signal levels against the NXP datasheet before production release. The D suffix denotes the 20-pin SO option, while other NXP order codes may use different package or shipping arrangements. Check the mechanical drawing and pin table for the selected ordering code rather than assuming every PCA9665-family order code has the same footprint.

RFQ צור קשר
PCA9665N - 1MHz FM+ Parallel-to-I2C Controller | NXP
PCA9665N

PCA9665N - 1MHz FM+ Parallel-to-I2C Controller | NXP

The NXP Semiconductors PCA9665N is a Fast-mode Plus parallel-bus to I2C-bus controller that supports data rates up to 1 MHz, provides a 68-byte data buffer, and offers 25 mA SCL/SDA drive capability. It is offered in a 20-pin through-hole DIP package for industrial applications. The device can operate as either an I2C master or slave and transfers data between a parallel microcontroller or microprocessor and a serial I2C bus. An I2C controller is an interface IC that bridges parallel processor buses and the serial I2C ecosystem. Parallel buses transfer multiple bits simultaneously, while I2C uses clocked SDA and SCL lines to exchange data between integrated circuits. The PCA9665N places this conversion in a dedicated peripheral, reducing the number of serial transactions and GPIO connections required by a host processor when it must control multiple I2C devices. The PCA9665N supports I2C Fast-mode Plus operation at 1 MHz and can drive SCL and SDA lines with 25 mA capability. Its 68-byte buffer supports byte-oriented and buffered data transfers between the parallel and serial sides. General Call support and software reset over the parallel bus add useful control functions for systems that need coordinated peripheral addressing or restart behavior. Two operating modes make the controller suitable for different system architectures. In master mode, it initiates transfers on the I2C bus; in slave mode, it responds to another bus controller. Communication can be interrupt-driven or managed through a polled handshake, allowing the interface to fit both event-driven firmware and simpler supervisory control loops. Typical applications include industrial control equipment, test and measurement systems, communication modules, peripheral expansion, legacy parallel-processor systems, and embedded products that need to retain a parallel bus while adding modern serial peripherals. Its through-hole DIP format is particularly useful for prototypes, legacy control boards, and industrial systems assembled around through-hole components. Designers should account for the 1 MHz bus limit, confirm that every connected I2C device supports the intended speed, and validate pull-up resistor sizing for the target bus voltage and capacitance. Because Fast-mode Plus uses lower resistance pull-ups than standard Fast-mode, incorrect resistor values can produce excessive rise times, ringing, or communication errors. This page organizes the manufacturer-described controller capabilities, package information, sourcing pathways, and engineering trade-offs into a concise selection guide. It also distinguishes the DIP-20 target from similarly named PCA9665 devices offered in SOIC, TSSOP, and HVQFN packages, which cannot replace this through-hole part without a PCB redesign.

RFQ צור קשר
PCA9670BS,118 - 8-bit Fm+ I2C I/O Expander w/ Reset, HVQFN-16
PCA9670BS,118

PCA9670BS,118 - 8-bit Fm+ I2C I/O Expander w/ Reset, HVQFN-16

The NXP PCA9670BS,118 is a remote 8-bit I/O expander for Fast-mode Plus (Fm+) I2C-bus with reset, packaged in a 16-pin HVQFN (3x3 mm) with exposed thermal pad. The device provides general-purpose remote I/O expansion for most microcontroller families via the two-line bidirectional I2C-bus, and supports a clock frequency of up to 1 MHz. Operating supply range is 2.3 V to 5.5 V, allowing use with 3.3 V and 5 V logic rails. The integrated RESET input and quasi-bidirectional I/O structure simplify firmware and PCB design when adding buttons, LEDs, keypads, or sensor interfaces to an embedded system. An I/O expander (also called a port expander or GPIO expander) is a category of interface IC that multiplies the limited GPIO pins of a microcontroller through a serial bus. In the taxonomy I/O expander -> interface IC -> integrated circuit -> semiconductor, the PCA9670BS sits in the parallel-bus-expansion tier and uses I2C as the transport. By attaching the part to SCL/SDA, designers gain eight additional quasi-bidirectional I/O pins addressed through a 7-bit slave address. Three hardware address pins (A0, A1, A2) allow up to 64 PCA9670 devices on the same bus, supporting up to 512 I/Os (for example 512 LEDs) without external bus buffers. Key features include 1 MHz Fm+ bus support (compared with 400 kHz for the classic PCF8574), a hardware RESET pin that reverts all ports to inputs, low standby current, and 5 V tolerant I/O structure that tolerates bus pulls above VDD. The HVQFN-16 (3x3) package provides a low 0.5 mm profile with an exposed die attach paddle for improved thermal performance, making it suitable for compact industrial, consumer, and IoT designs. NXP specifies ESD protection exceeding 2 kV HBM on the I/O pins, and the part is qualified to the industrial -40 C to +85 C operating range. The PCA9670 architecture uses an I2C state machine with interrupt logic for input-change notifications and a separate RESET input that asynchronously clears internal state. Internally each I/O pin is a quasi-bidirectional structure - capable of sinking current to drive LEDs directly while also serving as an input when written high. This dual-mode behavior differs from push-pull GPIO and is important when migrating designs from the older PCF8574/PCF8575 family. Typical applications include keypad and button-matrix scanning in white goods and access control, LED driving and chase patterns in industrial control panels, sensor multiplexing on Raspberry-Pi-class SBCs where the host lacks enough native GPIO, and general-purpose I/O expansion in PLC and HVAC controllers. The wide 2.3-5.5 V supply range plus 1 MHz Fm+ bus speed also suits battery-powered IoT nodes that need to minimize I2C transaction time. When designing with this part, place 100 nF decoupling close to VDD, use external pull-ups on SDA/SCL sized for the bus capacitance (typically 4.7 kohm at 1 MHz), and avoid leaving the RESET pin floating - tie it to VDD through a 10 kohm resistor or drive it from the host MCU. The I/O sink capability must be checked against LED forward current; sourcing current is limited and the quasi-bidirectional behavior must be considered when interfacing to logic-level peripherals. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the NXP datasheet.

RFQ צור קשר
PCA9671D - 16-Bit I2C FM+ I/O Expander | NXP
PCA9671D

PCA9671D - 16-Bit I2C FM+ I/O Expander | NXP

The NXP Semiconductors PCA9671D is a 16-bit remote I/O expander for I2C buses operating up to 1 MHz, with reset support and 16 general-purpose output ports. It is supplied in a 24-pin SO package designated 24-SO. The device adds 16 remotely controlled digital output lines to a host microcontroller while using only the two-wire I2C interface for communication. An I/O expander is an interface IC that extends the number of controllable input or output lines available from a host processor. The PCA9671D belongs to the I/O expander hierarchy within interface ICs and semiconductor devices. Its Fast-mode Plus capability allows a higher bus rate than conventional 400 kHz I2C operation, making it suitable for systems that need flexible logic-control functions without dedicating numerous host-controller pins. The main features include 16 output ports, 1 MHz I2C operation, a reset input, and configurable pull-up behavior represented by the PU designation. The reset function provides a defined way to restore the device state during system initialization or fault recovery. Each output can serve as a general-purpose logic signal, while bus-driven functions can extend the device beyond simple static GPIO control. The PCA9671D is designed for use with microcontrollers and other embedded processors that lack sufficient direct I/O pins. Its 24-pin SO package supports compact PCB layouts while keeping the I2C connection simple. Because an I/O expander adds bus-controlled peripheral functions around the processor, designers should account for bus timing, address allocation, pull-up resistors, output load limits, and reset timing in the system architecture. Typical uses include LED status and indicator arrays, relay-control interfaces, reset or enable signaling for external circuits, industrial control modules, communication equipment, and embedded systems with several discrete logic outputs. The 1 MHz bus rate can reduce communication delay when many outputs are updated, while the 16-bit output count consolidates control traffic into a compact serial interface. Layout should place pull-up components and decoupling close to the relevant device pins, and the I2C routing should preserve signal integrity. Firmware must assign a unique address, configure the intended output states, and account for the reset state before enabling external loads. The manufacturer datasheet is the controlling reference for absolute maximum ratings, electrical limits, pin functions, and recommended operating conditions. This product page consolidates the confirmed interface, package, and ordering information with practical design guidance for I2C layout, reset implementation, firmware configuration, and system expansion. It is intended to help engineers determine whether the PCA9671D can satisfy a remote-output requirement while avoiding unnecessary host-controller pin allocation.

RFQ צור קשר
PCA9672D - 8-Bit I/O Expander with 1 MHz I2C | NXP
PCA9672D

PCA9672D - 8-Bit I/O Expander with 1 MHz I2C | NXP

NXP Semiconductors PCA9672D is an 8-bit remote I/O expander with a 1 MHz I2C Fast-mode Plus interface, operating from 2.3 V to 5.5 V. The device provides eight quasi-bidirectional GPIO ports, three hardware address inputs, an interrupt output, and a reset input in a 16-pin SO package. An I/O expander is an interface IC that adds parallel digital input or output capability to a host controller over a serial bus. In the product hierarchy, the PCA9672D is an I/O expander within interface ICs and semiconductors. Its two-wire I2C connection reduces the number of host-controller pins required when a design needs additional control, status, or general-purpose I/O lines. The principal features include eight quasi-bidirectional ports, I2C Fast-mode Plus operation up to 1 MHz, three hardware address inputs, an interrupt output, and a reset input. The 2.3 V to 5.5 V operating range permits use in both 3.3 V and 5 V systems. Quasi-bidirectional ports can be configured individually as inputs or outputs, allowing the same external connector or control interface to combine input and output signals. The PCA9672D supports both interrupt-driven and polling-based host communication. An output port can generate an interrupt when a connected input changes state, allowing the host to handle events without continuously polling all eight inputs. The reset input provides a defined recovery path for the serial interface and port state. I2C address selection through three hardware address inputs permits multiple expanders on the same bus when their address straps are assigned differently. Typical uses include LED status and control panels, keypad and switch interfaces, industrial automation modules, sensor gathering, alarm and monitoring equipment, and compact embedded control boards. The 1 MHz bus rate is particularly useful for LED dimming or moderate-rate control traffic, while the interrupt output improves responsiveness in event-driven systems. Designers should verify the electrical characteristics of each quasi-bidirectional port, including its output-current capability and pull-up arrangement, before driving loads. The PCB layout should keep the I2C traces short, provide continuous ground references, and place bypass and pull-up components close to their associated pins. Firmware must also define startup states to avoid unintended outputs during reset. This product page combines the manufacturer feature summary, package identification, lifecycle information, ordering-code details, and practical guidance for I2C expansion, event handling, reset behavior, and PCB implementation. It also distinguishes exact ordering variants from unrelated interface ICs that use similar functions but do not share the same package and pin arrangement.

RFQ צור קשר
PCA9673D - 16-Bit I2C GPIO Expander | NXP Semiconductors
PCA9673D

PCA9673D - 16-Bit I2C GPIO Expander | NXP Semiconductors

The NXP Semiconductors PCA9673D is a remote 16-bit I/O expander for Fast-mode Plus I2C communication, operating at a maximum clock frequency of 1 MHz across a 2.3 V to 5.5 V supply range. The device is offered in a 24-pin SOIC package and provides interrupt and reset functions for connected microcontroller systems. An I/O expander is a peripheral interface IC that increases the number of general-purpose input or output lines available to a host processor. It sits within the embedded-control hierarchy as an I2C peripheral, allowing a microcontroller or application processor to control or monitor external signals over the two-wire bus instead of requiring one host GPIO for every external line. The PCA9673D therefore belongs to the interface IC family rather than the microcontroller or GPIO-controller families. Its principal features include 16 remotely controlled I/O lines, a 1 MHz I2C clock rate, compatibility with Fast-mode Plus operation, and dedicated interrupt and reset functions. The 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V system environments when the host, pull-up network, and external loads are designed for the corresponding voltage. The 24-pin SOIC format supports conventional surface-mount assembly and PCB routing. The PCA9673D is intended for systems in which a controller needs additional digital interface points. I2C address control, register-based configuration, and the interrupt output can reduce direct host-controller pin usage while providing a structured way to monitor external events. Because bus capacitance, pull-up resistance, voltage levels, and output timing influence reliable operation, the device should be used with a power supply and I2C network that remain within the manufacturer's stated limits. Typical uses include industrial control modules, sensor-hub boards, programmable logic controllers, test equipment, and compact embedded products that need more digital lines than the host controller provides. Its interrupt function is especially useful when an external change must wake or notify the host, while the reset function supports coordinated initialization of the expansion interface and attached circuitry. PCB layout should keep the I2C wiring short and route the SCL and SDA nets away from high-current switching edges. Confirm pull-up values for the intended bus voltage and frequency, provide suitable decoupling at the supply pins, and review the 24-pin pin-description table in the manufacturer datasheet before assigning every signal. The package drawing and pin names should be checked against the selected assembly footprint. This page consolidates the verified device specifications, ordering information, package details, replacement constraints, and practical implementation guidance into a design-oriented resource. It also distinguishes the documented PCA9673D configuration from order-code variants and explains which compatibility claims must be confirmed at the pin, voltage, and timing level before substitution.

RFQ צור קשר
PCA9674D - 8-Bit 1MHz I/O Expander | NXP Semiconductors
PCA9674D

PCA9674D - 8-Bit 1MHz I/O Expander | NXP Semiconductors

The NXP Semiconductors PCA9674D is an 8-bit remote I/O expander with a 1 MHz I2C Fast-mode Plus interface, eight quasi-bidirectional GPIO ports, and an interrupt output, supplied in a 16-pin SOIC package. Its operating supply range is 2.3 V to 5.5 V, making it suitable for low-voltage embedded systems and conventional 5 V industrial interfaces. An I/O expander is an interface IC that adds digital input and output ports through a serial bus. In the product hierarchy, the PCA9674D is an I/O expander within the interface IC category and a peripheral for microcontrollers and other I2C hosts. The host controller uses SCL and SDA to configure the ports, read inputs, change output states, and receive an interrupt when an input condition is detected. The PCA9674D provides eight quasi-bidirectional ports, a 1 MHz I2C bus, three hardware-selectable address inputs, and an interrupt output. Its eight ports can be individually configured as inputs or outputs through the device registers. Quasi-bidirectional ports include an internal pull-up arrangement and can support LED dimming through PWM-compatible output control. The I2C interface also allows multiple expanders to share one bus through address selection. The device supports up to 64 hardware-selectable addresses because A0, A1, and A2 provide three binary address inputs. This enables a bus to connect many remote I/O ports without requiring a separate microcontroller pin for each device. The PCA9674D and PCA9674A use non-overlapping slave-address ranges, allowing both families to operate together on the same I2C bus for further expansion. Typical uses include reading switches and push buttons, driving LEDs, controlling solenoid or relay interfaces, monitoring digital sensors, and adding GPIO capacity to industrial controllers. The 1 MHz bus rate also makes the device suitable for LED backlight control and other applications where the host must update multiple output states efficiently. PCB design should place the I2C pull-up resistors and bypass capacitor close to the appropriate supply and bus pins. Account for address selection before fixing the PCB, because the A0, A1, and A2 levels determine the slave address. Confirm that downstream devices remain compatible with the quasi-bidirectional port behavior before using an output pin as a strong source for a high-current load. This product page consolidates the electrical limits, package details, lifecycle information, pin assignments, sourcing guidance, and verified drop-in alternatives into one engineering reference. It also highlights the boundary between a true pin-compatible replacement and a functionally similar GPIO expander that requires a different footprint or interface arrangement.

RFQ צור קשר
PCA9674N - 8-Bit 1MHz I2C I/O Expander | NXP
PCA9674N

PCA9674N - 8-Bit 1MHz I2C I/O Expander | NXP

The NXP Semiconductors PCA9674N is an 8-bit remote I/O expander with a 1 MHz Fast-mode Plus I2C-bus interface, operating from 2.3 V to 5.5 V and housed in a 16-pin DIP package. It adds eight independently controlled GPIO outputs to a host microcontroller while providing an interrupt output for change notification. An I/O expander is an interface IC that extends the number of digital input or output pins available to a microcontroller or other bus controller. The PCA9674 belongs to the broader hierarchy of I2C interface ICs, parallel-port expanders, GPIO controllers, and power-management system semiconductors. It is useful when the host device has insufficient direct GPIO pins or when remote peripherals need to share a two-wire control bus. Three address-select inputs allow the PCA9674 to be assigned among 64 addresses, supporting up to 126 PCA9674 and PCA9674A devices on one I2C-bus without bus buffers and as many as 1,008 controlled I/Os. Its 1 MHz bus speed exceeds the 100 kHz Standard-mode rate, while the 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V systems. The interrupt output enables a host to respond to port events without continuously polling all eight outputs. The device separates serial bus control from parallel output handling. The host writes to the PCA9674 registers over I2C and receives an interrupt when a configured output state changes. Its 8-bit organization and hardware-selectable address pins make multiple expanders practical in LED panels, control boards, and distributed peripheral interfaces. The through-hole 16-DIP format is also convenient for prototyping and through-hole industrial assemblies. Typical uses include LED status indicators, relay or contactor control, display and keypad interfaces, industrial control modules, and general-purpose board I/O expansion. The PCA9674 is particularly suitable when a microcontroller must monitor remote logic states while preserving limited pins for communications, timing, or analog functions. For reliable implementation, connect pull-up resistors to the SDA and SCL lines, route the bus away from noisy switching nodes, and treat the address pins as board-level configuration. Verify the 2.3 V to 5.5 V operating range against the voltage applied to VDD and the logic levels used by the connected host. This page consolidates the NXP device specifications, address architecture, package information, selection guidance, and practical integration notes. It also identifies the closest same-footprint alternatives while clearly distinguishing confirmed orderable variants from functionally similar devices that require additional design review.

RFQ צור קשר
PCA9675D - 16-Bit I/O Expander, 1 MHz | NXP
PCA9675D

PCA9675D - 16-Bit I/O Expander, 1 MHz | NXP

The NXP Semiconductors PCA9675D is a remote 16-bit I/O expander for I2C buses, supporting clock speeds up to 1 MHz in a 24-pin SOIC package. It provides a Fast-mode Plus compatible interface, interrupt support, and general-purpose output expansion for microcontroller-based systems. The device is positioned as a drop-in upgrade for the PCF8575 while increasing I2C-bus speed from 400 kHz to 1 MHz and supporting PWM LED dimming. An I/O expander is an interface IC that increases the number of general-purpose input or output lines available to a host microcontroller. By connecting these additional lines over a two-wire I2C bus, the PCA9675D reduces the pin count required on processors with limited direct I/O. It sits within the interface-IC hierarchy and connects a microcontroller to external indicator, lighting, switch, and control circuits without requiring a large number of host GPIO pins. The principal features of the PCA9675D include 16 remotely controlled I/O lines, operation from a 2.3 V to 5.5 V supply range, and I2C communication up to 1 MHz. Its Fast-mode Plus capability is significant when the expanded outputs are used for LED PWM dimming because the system can update a larger number of outputs more rapidly than a conventional 400 kHz I2C implementation. The interrupt output provides a mechanism for notifying the host when a monitored input changes. The PCA9675D is intended to work with most microcontroller families that support a compatible I2C interface. Its 24-pin SOIC package, 1 MHz bus capability, and 16-bit expansion make it suitable for applications where a conventional PCF8575-class expander would impose a lower 400 kHz bus limit. The device also supports both 30 mA I2C-bus drive and higher-bus-speed operation compared with the referenced PCF8575 architecture. Typical applications include LED signs and displays, server and networking equipment, industrial control systems, PLC peripheral interfaces, cellular telephone equipment, gaming machines, and instrumentation or test equipment. In an LED dimming design, the host writes output states and PWM information over I2C, while the expander handles the timing and level conversion required by multiple external LED channels. PCB design should preserve short I2C routing, minimize branch-stub length, and provide suitable pull-ups on SCL and SDA. Decoupling close to the supply pins is important for dependable operation in systems containing switching converters. Because the PCA9675D can source or sink substantial I2C current, bus capacitance, pull-up resistance, voltage level, and simultaneous operating current should be checked against the device limits before production release. This page combines the manufacturer's product information, package and interface characteristics, replacement guidance, comparison parameters, and practical implementation considerations. It also identifies the important distinction between a genuine SOIC-24 drop-in alternative and options that require a different footprint, allowing engineers to make a board-level replacement decision without relying on generic cross-reference results.

RFQ צור קשר
PCA9675PW,118 - 16-bit Fm+ I2C I/O Expander | NXP | TSSOP-24
PCA9675PW,118

PCA9675PW,118 - 16-bit Fm+ I2C I/O Expander | NXP | TSSOP-24

The NXP PCA9675PW,118 is a 16-bit remote I/O expander for the Fast-mode Plus (Fm+) I²C-bus, supplied in a 24-pin TSSOP (PW) package and shipped on 13-inch tape and reel. It operates from a supply voltage of 2.3 V to 5.5 V, clocks the I²C interface at up to 1 MHz, and exposes 16 quasi-bidirectional I/O lines that can source/sink up to 30 mA per pin with a 100 mA total package limit. An I/O expander (also called a port expander or GPIO expander) is a category of interface IC that increases the number of general-purpose I/O pins available to a host microcontroller over a serial bus such as I²C. In the system hierarchy it sits between the MCU and the discrete digital loads (LEDs, keypads, sensors, relay coils), translating compact I²C transactions into parallel pin-level updates. The PCA9675 belongs to NXP's Fm+ family, which is optimized for high-speed serial I/O expansion in noisy or long-trace industrial backplanes. Key features include three hardware address pins (A0/A1/A2) supporting up to eight PCA9675 devices on the same bus, an active-low interrupt output (INT) that asserts when any input changes and releases on the next I²C read, an active-low reset input with internal power-on reset, and per-pin latch-up current exceeding the 100 mA JESD78 limit. The device is a drop-in upgrade for the legacy PCF8575, lifting bus speed from 400 kHz to 1 MHz and raising sink current capability. Typical applications include PWM dimming of LED arrays (each pin can be modulated at >1 MHz bus rates), keypad and switch-matrix scanning, fan-speed and relay control in industrial PLCs, and general-purpose I/O expansion for low-pin-count MCUs in white goods, HVAC, and IoT edge nodes. Designers value the wide 2.3–5.5 V supply range because it allows direct interface to both 3.3 V and 5 V microcontrollers without level shifters. When designing with this device, place 100 nF decoupling on VDD as close as possible to the pin and pull SDA/SCL high with 4.7 kΩ resistors for standard 400 kHz operation or 1 kΩ for the full 1 MHz Fm+ rate. Note that quasi-bidirectional outputs require no external pull-up on the load side because an internal weak pull-up is enabled after each read cycle.

RFQ צור קשר
PCA9703PW/Q900 - 16-bit SPI GPI, 18V Tolerant | NXP
PCA9703PW/Q900

PCA9703PW/Q900 - 16-bit SPI GPI, 18V Tolerant | NXP

The NXP Semiconductors PCA9703PW/Q900,118 is an 18 V tolerant, 16-bit SPI General Purpose Input (GPI) shift register with maskable interrupt output, housed in a 24-pin TSSOP (PW) package rated -40 C to +125 C. It operates as an SPI slave at up to 5 MHz and monitors 16 switch or logic inputs with 18 V input tolerance, making it a low-power solution for high-voltage switch status monitoring in automotive and industrial systems. A GPI (General Purpose Input) shift register is a type of input-only I/O expander within the broader hierarchy of interface ICs -> I/O expanders -> parallel-in serial-out shift registers. Unlike I2C GPIO expanders, SPI GPI shift registers stream input states to a microcontroller as a serial bit field, which minimizes pin count on the host MCU and gives deterministic, fast read-back of many switch contacts. Key features include 16 input-only channels tolerant to 18 V regardless of the device supply, a maskable INT output that flags any change of input state, a 3 V input switching threshold for robust noise immunity, and SPI compatibility up to 5 MHz. The Q900 suffix and /Q900,118 ordering code identify the automotive AEC-Q100 compliant variant with extended -40 C to +125 C operation; NXP states that PCA9703PW/Q900 is AEC-Q100 compliant and PPAP documentation is available via i2c.support@nxp.com. Technically, the PCA9703 samples its 16 GPI inputs into an internal shift register and shifts data out on MISO under host control of CS and SPI clock. Any input change (open, closed, or 12 V/24 V level via divider) triggers the interrupt output, which can be masked to prevent nuisance CPU wake-ups. The low-power CMOS process keeps static consumption minimal, which is critical for always-on battery-backed switch monitoring. Typical applications include automotive switch monitoring (door, window, seat, and steering-column switches), industrial control panels and limit-switch monitoring, and 12 V/24 V system status sensing where contacts ride on battery-level rails the chip inputs directly tolerate. A key design consideration is input threshold scaling: although inputs tolerate 18 V, the 3 V threshold means designers must confirm logic levels and switch pull-up arrangements so that a valid LOW is below threshold and a valid HIGH is safely above it across temperature. This page synthesizes distributor pricing, lifecycle status, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר
PCA9703PW/Q900,118 - 16-Bit SPI GPI 18V Tolerant | NXP
PCA9703PW/Q900,118

PCA9703PW/Q900,118 - 16-Bit SPI GPI 18V Tolerant | NXP

The NXP Semiconductors PCA9703PW/Q900,118 is an 18 V tolerant SPI 16-bit General Purpose Input (GPI) shift register with maskable interrupt output, supplied in a 24-pin TSSOP package rated for -40 C to +125 C automotive operation with a 4.5 V to 5.5 V supply and a 5 MHz SPI clock. A general purpose input shift register is a specialized interface IC that converts parallel logic levels from switches or sensors into a serial data stream. In the system hierarchy it sits between raw switch inputs and a microcontroller: instead of dedicating 16 MCU pins to switch monitoring, a single SPI port reads all 16 inputs as a serial word, reducing pin count, wiring harness complexity, and cost in distributed control systems. Key features include 18 V tolerance on all GPI pins, allowing direct connection to automotive battery-nominal rails without level shifting; a maskable interrupt output (INT) with an INT_EN pin that disables the inputs and interrupt to minimize battery drain in cyclically powered systems; and an SDIN pin with pull-down that supports daisy-chaining multiple devices on a single SPI bus for 32, 48, or more inputs. Architecturally, the PCA9703 uses a shift register with a dedicated output enable controlled by CS. The 3 V logic thresholds on the serial interface ensure compatibility with both 3.3 V and 5 V controllers. Switch status is captured in the parallel input register and shifted out MSB-first on SCLK edges, with the interrupt flag readable on the first serial byte so the MCU can branch quickly on any input change. Typical applications include automotive switch monitoring for door, seat, and steering-column controls, body control modules and keypads, and industrial panels requiring isolated or battery-tolerant digital inputs. The 18 V tolerance is the decisive parameter wherever switches are wired to unregulated supply rails. A key design consideration: the GPI inputs require external pull-up or pull-down resistors to the switched rail; the INT_EN pin should be driven low during system sleep to eliminate quiescent current drawn through those resistors. This page synthesizes distributor pricing, drop-in alternative analysis, design notes, and application guidance not found in the manufacturer datasheet, making it a one-stop engineering reference for the PCA9703PW/Q900,118.

RFQ צור קשר
PCA9704PW/Q900 - 8-bit SPI GPI 18V Tolerant | NXP
PCA9704PW/Q900

PCA9704PW/Q900 - 8-bit SPI GPI 18V Tolerant | NXP

The NXP Semiconductors PCA9704PW/Q900 is an 8-bit, 18 V tolerant SPI General Purpose Input (GPI) shift register with maskable interrupt, AEC-Q100 qualified for automotive applications, housed in a 16-pin TSSOP (PW) package. It monitors the status of switch inputs and reads them out over a standard SPI interface running at up to 5 MHz. A general-purpose input expander is an interface IC that offloads switch or status-signal monitoring from a microcontroller. In the signal-chain hierarchy, the PCA9704 sits between discrete switch contacts and an MCU's SPI peripheral: GPIO expander -> interface IC -> mixed-signal logic device. Input expanders are used when an MCU lacks sufficient input pins or when switch signals sit at voltages higher than the MCU supply, as is common in automotive 12 V and 24 V electrical systems. Key features include eight input channels each tolerant to 18 V, allowing direct connection to battery-referenced switch contacts without external level shifting or clamping networks. The SPI interface supports read-out at up to 5 MHz, and a maskable interrupt output (INT) alerts the host controller only when inputs change, enabling low-power polled or event-driven system architectures. Technically, the PCA9704 is implemented as a parallel-in serial-out shift register with input latching. When the host asserts the chip-select, the current input state is latched and shifted out on the SPI data line; devices can be cascaded to expand beyond eight inputs on a single SPI bus. The /Q900 suffix denotes NXP's automotive product-line extension with AEC-Q100 compliance and PPAP support, distinguishing it from the commercial-grade PCA9704PW. Typical applications include automotive switch monitoring (door, seat, and key contacts), industrial control-panel status readback, and system diagnostics where battery-level fault or presence signals must be safely captured by a low-voltage controller. Design consideration: although the 18 V tolerance removes the need for input dividers, verify worst-case battery load-dump transients in automotive systems and confirm that the interrupt mask register is initialized before enabling INT to avoid spurious wake-ups at power-up. This page synthesizes distributor data, automotive-grade alternative options, and practical SPI integration notes not found in the manufacturer datasheet, with pricing verified as of 2026-10-19.

RFQ צור קשר
PCAL6408AHK - 8-Bit I2C I/O Expander, XQFN-16 | NXP
PCAL6408AHK

PCAL6408AHK - 8-Bit I2C I/O Expander, XQFN-16 | NXP

The NXP Semiconductors PCAL6408AHK is a low-voltage translating, 8-bit general-purpose I/O expander with interrupt output, reset, and Agile I/O configuration registers, interfacing to a host microcontroller via I2C-bus/SMBus at up to 400 kHz in a 16-pin XQFN (1.8 x 2.6 mm) package. An I/O expander is a peripheral IC that adds extra general-purpose input/output pins to a microcontroller or embedded processor over a serial bus such as I2C or SMBus. In the system hierarchy, it sits within the interface IC family, under mixed-signal peripheral devices, and complements microcontrollers whose native GPIO count is exhausted. Expanders offload GPIO expansion while consuming only two bus wires (SDA, SCL), conserving processor pins and board routing. Key features include a wide supply range of 1.65 V to 5.5 V, dual power rails for true voltage level translation between logic domains, programmable output drive strength, and latchable inputs. The interrupt output and active-low reset provide robust event-driven and fault-recovery behavior in multi-slave I2C systems. The Agile I/O feature set - configurable output drive, input latch, and pull-up/pull-down enable - allows system designers to tune signal integrity and power per pin, which is significant in mixed-voltage designs where a 1.8 V MCU must safely drive 3.3 V or 5 V peripherals. Open-drain and push-pull operating modes over I2C/SMBus at 400 kHz provide flexible bus integration. Typical applications include GPIO expansion in portable and battery-powered devices, level translation between low-voltage processors and legacy 5 V peripherals, sensor and keypad scanning, LED control, and backplane status monitoring in industrial systems. Design consideration: because the XQFN-16 package measures only 1.8 x 2.6 mm, the exposed pad must be soldered to a grounded PCB land pattern for reliable thermal and mechanical performance; verify land-pattern tolerances before assembly. This page synthesizes distributor pricing context, drop-in alternatives, practical design notes, and AEO-optimized FAQs not found in the NXP datasheet.

RFQ צור קשר
PCF2123BS/1 - SPI RTC Calendar IC | 16-HVQFN | NXP
PCF2123BS/1

PCF2123BS/1 - SPI RTC Calendar IC | 16-HVQFN | NXP

The NXP Semiconductors PCF2123BS/1 is a CMOS Real-Time Clock (RTC) and calendar with a Serial Peripheral Interface (SPI-bus) operating up to 6.25 Mbps, supplied at 1.1 V to 5.5 V, packaged in a 16-pin HVQFN exposed-pad package. It integrates time-of-day, calendar, alarm, timer and interrupt functions with an integrated 32.768 kHz crystal resonator space on chip, drawing less than 100 nA at 2.0 V for ultra-low standby power. A Real-Time Clock (RTC) is a dedicated integrated circuit that maintains accurate time and date information independent of system power. RTCs sit within the broader category of power management companions and timing ICs, working alongside MCUs, FPGAs and SoCs to provide timekeeping during main-power-off conditions through a small backup cell or supercapacitor. They typically expose time registers in BCD format and communicate over serial buses such as I2C or SPI. The PCF2123BS/1 uses SPI for higher throughput where speed and noise immunity matter. Key features include a wide 1.1 V to 5.5 V supply range, less than 100 nA typical current consumption at 2.0 V, integrated alarm and timer functions, an interrupt output, and a wide operating temperature range suitable for industrial environments. The device is supplied in a compact 3 mm x 3 mm HVQFN-16 plastic package with a thermal pad, drawing less than 0.2 microW of power to support battery-backed operation. The PCF2123BS/1 uses CMOS logic and on-chip tuning, allowing timekeeping accuracy to be compensated via load and trim registers. The SPI interface supports a maximum data rate of 6.25 Mbps, enabling fast register access by host processors. The integrated power-on reset and trickle charger functionality simplify backup power design. Typical applications include battery-backed timekeeping in metering, data loggers, industrial controllers, white goods and IoT sensor nodes, and any portable embedded system that needs a low-power accurate wall-clock reference independent of the main MCU. When designing with this device, place a 100 nF decoupling capacitor close to VDD and connect the exposed thermal pad to a clean ground pour. Always handle the SPI chip-select correctly to avoid bus contention with other peripherals on the same SPI bus. The NXP product page notes End-of-Life status, so check availability before new designs. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes not consolidated in the manufacturer datasheet, providing engineers with a faster decision path.

RFQ צור קשר
PCF51JM128EVLK - 32-Bit ColdFire V1 MCU, 128KB Flash | NXP
PCF51JM128EVLK

PCF51JM128EVLK - 32-Bit ColdFire V1 MCU, 128KB Flash | NXP

The NXP PCF51JM128EVLK is a 32-bit ColdFire V1 microcontroller from the MCF51JM Series, delivering 50 MHz core performance with 128 KB of embedded Flash and 16 KB of SRAM, housed in an 80-pin LQFP (14x14 mm) package. It integrates USB OTG, CAN, I2C, SCI, and SPI connectivity in a single device, targeting cost-sensitive industrial and embedded USB applications. Background Knowledge: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and peripheral interfaces (UART, timers, ADC, GPIO, USB, CAN, etc.). ColdFire V1 is NXP's 32-bit RISC architecture derived from the original Motorola 68000 instruction set, optimized for embedded systems that need higher performance than 8/16-bit MCUs without the overhead of ARM Cortex-M cores. MCF51JM Series specifically adds USB On-The-Go capability, making it a popular choice for USB peripherals and industrial controllers. Key differentiating features include the integrated USB 2.0 Full-Speed OTG controller (with on-chip transceiver and pull-up/pull-down resistors), 66 general-purpose I/O pins, and a rich peripheral set: 2x SCI (UART), 2x SPI, 2x I2C, 6-channel PWM, a 12-bit ADC, and a 16-bit timer. The 80-LQFP package provides generous pin count for multi-interface designs while remaining hand-solderable for prototyping. Technical depth: The ColdFire V1 core uses a 16/32-bit variable-length instruction encoding that balances code density with 32-bit throughput. The integrated USB OTG controller supports both device and host roles with internal 3.3V regulator and DP/DM pull resistors, eliminating external PHY components. The Flash controller supports in-application programming (IAP) and byte-level EEPROM emulation, allowing non-volatile data storage alongside the main 128 KB program image. Typical applications include USB-to-UART bridges, USB human-interface devices (HID), industrial control nodes with CAN connectivity, low-cost sensor hubs, and embedded controllers in appliances. The combination of USB, CAN, and multi-protocol serial interfaces makes it ideal for industrial gateways that aggregate sensor data over CAN and expose it to a host PC via USB. Design consideration: The USB D+/D- traces must be routed as a 90-ohm differential pair with length matching; bypassing the on-chip 3.3V regulator to power the MCU core requires a 4.7 uF decoupling capacitor on the VREG pin. The device operates from -40C to +85C industrial temperature range. This page synthesizes distributor availability, drop-in same-package alternatives, and design notes not found in the manufacturer datasheet to support sourcing and design decisions.

RFQ צור קשר
PCF51JM128VLH - 32-bit ColdFire MCU, 128KB Flash, USB OTG | NXP
PCF51JM128VLH

PCF51JM128VLH - 32-bit ColdFire MCU, 128KB Flash, USB OTG | NXP

The NXP PCF51JM128VLH is a 32-bit ColdFire V1 MCF51JM microcontroller delivering 50 MHz CPU performance with 128 KB of Flash program memory and 16 KB of RAM, housed in a 64-pin LQFP (10x10 mm) package. It integrates USB OTG (On-The-Go) connectivity alongside CANbus, I2C, SCI, and SPI peripheral interfaces, and exposes 51 general-purpose I/O pins for mixed-signal embedded designs. What is a ColdFire microcontroller? ColdFire is a 32-bit reduced instruction set computing (RISC) architecture originally derived from the Motorola 68000 family and maintained today by NXP. Within the broader taxonomy, a ColdFire MCU belongs to the hierarchy: microcontroller -> embedded processor -> semiconductor. ColdFire V1 targets cost-sensitive, deterministic real-time applications, balancing 32-bit performance with low power consumption. It is widely deployed in industrial control, USB peripherals, automotive body electronics, and consumer devices where deterministic interrupt latency and a mature toolchain matter more than raw MHz. Key features of the PCF51JM128VLH include 128 KB of embedded Flash for program storage, 16 KB of SRAM for data and stack, a 50 MHz ColdFire V1 core, and integrated USB OTG with on-chip transceiver - eliminating the need for an external PHY. The device also includes a low-voltage detection (LVD) module, programmable watchdog timer, multiple PWM channels, and 51 GPIO pins. The 64-LQFP (10x10 mm) package provides ample pin count for mixed-signal designs while remaining compatible with hand-solderable and reflow processes. The integrated USB OTG controller is the defining architectural feature. Unlike MCUs that require an external USB peripheral controller, the PCF51JM128VLH implements the USB 2.0 full-speed transceiver, serialization, and protocol engine on-die. This simplifies USB device, host, and On-The-Go designs while reducing BOM cost. The ColdFire V1 core paired with hardware USB enables deterministic USB latency, which is valuable for industrial USB instrumentation, human-interface devices (HID), and point-of-sale terminals. Typical applications include USB HID peripherals such as custom keyboards and barcode scanners, industrial CAN nodes communicating over CANbus with USB diagnostics, USB-to-serial bridge converters, low-speed consumer devices with USB charging or data interfaces, and human-machine interface (HMI) panels with mixed digital I/O. The 128 KB Flash budget is sufficient for USB stacks (e.g., Freescale/NXP bare-metal or MQX-compatible USB frameworks) plus application code. When designing with this part, allocate sufficient decoupling on VDD (typically 100 nF + 10 uF bulk near the pins) and follow NXP's reference layout for the USB DP/DM differential pair. Because the device is in the obsolete lifecycle stage per the verified distributor data, validate long-term availability with your supply chain team before committing to new production runs. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר
PCF51QU64VLF - Coldfire V1 MCU 32-Bit 50MHz 64KB Flash 48-LQFP | NXP Semiconductors
PCF51QU64VLF

PCF51QU64VLF - Coldfire V1 MCU 32-Bit 50MHz 64KB Flash 48-LQFP | NXP Semiconductors

The NXP Semiconductors PCF51QU64VLF is a 32-bit Coldfire V1 microcontroller from the MCF51Qx family, integrating 64KB of program flash and running at up to 50MHz core clock, housed in a 48-pin LQFP (7x7 mm) package. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program and working memory, peripherals, and I/O on one die. The Coldfire V1 core is an NXP-specific implementation of a variable-length RISC architecture derived from the original Coldfire line, optimized for deterministic embedded control with low power consumption. MCUs sit hierarchically beneath microprocessors and systems-on-chip, and they dominate the embedded controller category in industrial, appliance, and consumer products. Key specifications include 64KB (64K x 8) embedded flash memory, 35 general-purpose I/O lines, and a peripheral set featuring DMA, LVD (low-voltage detect), POR (power-on reset), PWM channels, and an EBI/EMI external bus interface. Connectivity options include one I2C bus, one SPI bus, and one UART/USART channel. The device is characterized for a supply voltage range from 1.8V to 3.6V (with flash write voltage range specified separately), and operates across an extended industrial temperature range. The Coldfire V1 core implements a single-cycle multiply-accumulate and a tightly-coupled peripheral bridge, enabling deterministic interrupt latency suitable for motor control and power conversion loops. The 50MHz maximum CPU frequency yields approximately 50 MIPS of throughput, and the unified address space simplifies C-language firmware development with standard toolchains such as CodeWarrior. Typical applications include industrial control modules, low-end consumer appliances, smart sensor nodes, and small-format human-machine interface boards. The combination of 64KB flash and an external bus makes the PCF51QU64VLF especially well suited to designs that must execute a real-time control loop while still communicating with external memory-mapped peripherals. A critical design consideration is decoupling: place a 100nF ceramic bypass on each VDD/VSS pair within two millimeters of the package, and reserve a 4.7uF bulk capacitor near the regulator output. The external bus pins (EBI/EMI) require series termination when driving long PCB traces to avoid ringing. This page synthesizes distributor stock, drop-in alternatives from the same Freescale/NXP MCF51Q family, and practical design notes not found on a single manufacturer product page.

RFQ צור קשר