NXP Semiconductors

PCA9671D - 16-Bit I2C FM+ I/O Expander | NXP

MPN: PCA9671D ✓ פעיל
24 pins Package 1 MHz Speed
כמות הזמנה מינימלית: 1 |

PCA9671D סקירה

The NXP Semiconductors PCA9671D is a 16-bit remote I/O expander for I2C buses operating up to 1 MHz, with reset support and 16 general-purpose output ports. It is supplied in a 24-pin SO package designated 24-SO. The device adds 16 remotely controlled digital output lines to a host microcontroller while using only the two-wire I2C interface for communication.

An I/O expander is an interface IC that extends the number of controllable input or output lines available from a host processor. The PCA9671D belongs to the I/O expander hierarchy within interface ICs and semiconductor devices. Its Fast-mode Plus capability allows a higher bus rate than conventional 400 kHz I2C operation, making it suitable for systems that need flexible logic-control functions without dedicating numerous host-controller pins.

The main features include 16 output ports, 1 MHz I2C operation, a reset input, and configurable pull-up behavior represented by the PU designation. The reset function provides a defined way to restore the device state during system initialization or fault recovery. Each output can serve as a general-purpose logic signal, while bus-driven functions can extend the device beyond simple static GPIO control.

The PCA9671D is designed for use with microcontrollers and other embedded processors that lack sufficient direct I/O pins. Its 24-pin SO package supports compact PCB layouts while keeping the I2C connection simple. Because an I/O expander adds bus-controlled peripheral functions around the processor, designers should account for bus timing, address allocation, pull-up resistors, output load limits, and reset timing in the system architecture.

Typical uses include LED status and indicator arrays, relay-control interfaces, reset or enable signaling for external circuits, industrial control modules, communication equipment, and embedded systems with several discrete logic outputs. The 1 MHz bus rate can reduce communication delay when many outputs are updated, while the 16-bit output count consolidates control traffic into a compact serial interface.

Layout should place pull-up components and decoupling close to the relevant device pins, and the I2C routing should preserve signal integrity. Firmware must assign a unique address, configure the intended output states, and account for the reset state before enabling external loads. The manufacturer datasheet is the controlling reference for absolute maximum ratings, electrical limits, pin functions, and recommended operating conditions.

This product page consolidates the confirmed interface, package, and ordering information with practical design guidance for I2C layout, reset implementation, firmware configuration, and system expansion. It is intended to help engineers determine whether the PCA9671D can satisfy a remote-output requirement while avoiding unnecessary host-controller pin allocation.

חלופות תחליף ישיר עבור PCA9671D — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

אין חלופות תואמות Drop-in עבור מוצר זה.

בקשת חלופות

PCA9671D מפרטים

Number of I/O Outputs 16 outputs
I2C Maximum Clock Frequency 1 MHz
סוג ממשק I2C Fast-mode Plus (Fm+)
Reset Function Yes
Pull-Up Configuration PU
Package Pin Count 24 pins
Package Designation 24-SO
Device Category I/O expander
סוג הרכבה Surface mount

מדריך תצורת פינים של PCA9671D 24-so

תצורת פינים עבור PCA9671D (מארזת 24-so). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 24-so עבור PCA9671D

אין נתוני פריסת פינים מפורטים עבור PCA9671D.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

PCA9671D מתאים עבור 6 יישוםs: LED Status and Indicator Arrays, Relay and Discrete Logic Control, Embedded System I/O Expansion, Communication Equipment Control, Power-Sequencing and Enable Control, Instrumentation and Test Control.

💡

LED Status and Indicator Arrays

The PCA9671D fits LED status and indicator designs because it provides 16 outputs while operating on an I2C bus up to 1 MHz. A host microcontroller can update several visual indicators over the same two-wire bus instead of consuming one dedicated GPIO pin for every lamp. The reset function supports deterministic initialization of the display state after power-up. Because the manufacturer documentation associates PCA9671 capability with bus-driven LED functions, engineers should verify output-drive limits, polarity, and the required PWM configuration in the NXP datasheet. The principal benefit is PCB and firmware simplicity, while the trade-off is that each update consumes I2C bus time and all remote outputs share the host's bus reliability.

🏭

Relay and Discrete Logic Control

The PCA9671D is suitable for relay-control and discrete-logic interfaces when the host controller has limited GPIO capacity. Sixteen output lines can represent relay commands, equipment enables, alarms, or interlock signals through suitable external interface circuitry, while the 1 MHz Fm+ bus supports comparatively quick command transfer. Reset provides a controlled recovery point during startup or system faults. Designers must confirm voltage levels, output current, isolation requirements, and whether an external driver stage is necessary before connecting a load. The PCA9671D reduces host-pin usage, but it does not replace high-current drivers, isolation, or protection required by the final relay and industrial interface circuit.

🧩

Embedded System I/O Expansion

The PCA9671D is a practical choice when an embedded processor must support more digital control lines than its package provides. The 16-bit remote I/O structure allows a microcontroller or application processor to retain a compact pin count while adding status and control points elsewhere on a PCB. The I2C interface operates up to 1 MHz, and reset provides an initialization mechanism for the expanded outputs. The 24-SO package must be checked against the PCB footprint and assembly process. The design trade-off is bus dependency: firmware must configure addresses and output states, while the I2C network must maintain timing margins and reliable pull-ups for all connected devices.

🌐

Communication Equipment Control

The PCA9671D fits communication equipment that requires several remote enables, status indicators, or module-control signals without dedicating a large number of host pins. Its 16 outputs and 1 MHz I2C operation allow control traffic to be consolidated on the processor's existing two-wire bus. Reset can be incorporated into the equipment's startup and recovery sequence. System planners should use the NXP timing information to validate bus capacitance, pull-up selection, and the number of competing I2C devices. The PCA9671D simplifies the processor interface, but address conflicts, bus faults, and software state management remain the designer's responsibility.

⚡

Power-Sequencing and Enable Control

The PCA9671D can distribute enable, reset, or power-sequencing commands to multiple peripheral circuits when direct host-controller pins are limited. Sixteen outputs provide room for several controlled loads, while the reset input establishes a known initialization point for the expansion interface. The device's I2C command path supports compact routing and software-configurable output states. Timing analysis must show that all downstream circuits tolerate the reset and startup sequence, and the NXP datasheet must be consulted for output-mode and electrical-limit details. The benefit is centralized sequencing with fewer host pins; the trade-off is that firmware must coordinate the sequence and avoid enabling loads before the surrounding system is ready.

🔧

Instrumentation and Test Control

The PCA9671D is well suited to instrumentation and test systems that need multiple remote control lines across a larger circuit board. The 16 outputs can operate front-panel indicators, range-select commands, fixture enables, or status lamps while the 1 MHz I2C bus keeps the controller connection compact. Reset supports repeatable initialization before a measurement sequence. Layout should preserve I2C signal integrity and provide local decoupling, while firmware should avoid unnecessary bus traffic during high-rate acquisition. The PCA9671D offers a practical alternative to expanding the controller package, although it introduces a software-controlled dependency that must be included in system-level fault analysis.

סיכום מוצרים מומלצים

PCA9671D NXP Semiconductors בשימוש ב-: LED Status and Indicator Arrays, Relay and Discrete Logic Control, Embedded System I/O Expansion, Communication Equipment Control, Power-Sequencing and Enable Control, Instrumentation and Test Control PCA9671D,118 Orderable SO-24 configuration of the expander בשימוש ב-: LED Status and Indicator Arrays, Embedded System I/O Expansion, Power-Sequencing and Enable Control PCA9671D,112 Orderable configuration used for remote logic outputs בשימוש ב-: Relay and Discrete Logic Control, Communication Equipment Control, Instrumentation and Test Control
What is the PCA9671D used for?
The PCA9671D is a 16-bit I2C I/O expander that gives a host controller 16 additional remote output lines. According to the NXP manufacturer datasheet, it is intended for general-purpose remote I/O expansion and belongs to the Fast-mode Plus family. It is particularly useful when a microcontroller has too few direct GPIO pins for indicators, relays, enables, or other discrete logic signals.
How fast is the PCA9671D I2C bus?
The PCA9671D supports I2C operation up to 1 MHz. The NXP manufacturer datasheet identifies the device as part of the Fast-mode Plus family, while distributor technical listings also identify a 1 MHz maximum I2C clock. This rate exceeds conventional 400 kHz Fast-mode operation and can shorten transaction time when multiple output states are updated.
How many I/O outputs does the PCA9671D provide?
The PCA9671D provides 16 I/O outputs. The NXP manufacturer datasheet describes it as a 16-bit remote I/O expander, and the device is packaged in a 24-pin SO package. The I2C interface carries commands from the host controller, allowing the 16 lines to be used for logic-level control, status indication, or bus-driven peripheral functions.
Where can I download the PCA9671D datasheet PDF?
The PCA9671D datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/PCA9671.pdf. Use the manufacturer document for the complete pin description, electrical characteristics, timing diagrams, reset behavior, and recommended application circuit. The search result also identifies the device as a remote 16-bit I/O expander for an Fm+ I2C-bus with reset.
What is the PCA9671D package and pin count?
The PCA9671D is supplied in a 24-pin SO package, also identified in distributor listings as 24-SO. The corresponding package drawing key for this record is soic-24 because the listed package contains 24 pins. Pin assignments and the exposed thermal or electrical functions must be taken from the NXP datasheet rather than inferred from the package name.
Does the PCA9671D have a reset pin?
Yes, the PCA9671D includes a reset function. The NXP manufacturer datasheet describes the device as a remote 16-bit I/O expander for an Fm+ I2C-bus with reset, and distributor listings separately identify the reset and PU functions. Systems should use the reset behavior specified by NXP when designing startup and fault-recovery sequencing.
Can the PCA9671D replace a PCF8575?
The PCA9671 is described by NXP as a drop-in upgrade for the PCF8575, with a higher I2C speed of 1 MHz versus 400 kHz and greater I2C drive capability of 30 mA versus 3 mA. Because package variants can have different pin assignments and dimensions, confirm that the selected orderable part uses the same SO-24 footprint and verify all signal functions before substitution.
PCA9671D vs PCA9671PW: which package should I choose?
The PCA9671D is listed in a 24-SO package, while the PCA9671PW product information identifies the PW package option. Both provide the PCA9671 function, but package body dimensions, lead geometry, pin layout, and assembly requirements must be compared before using one as a drop-in replacement. Choose the variant whose land pattern and pin numbering match the existing PCB.
When should I choose the PCA9671D over a microcontroller with more GPIO pins?
Choose the PCA9671D when the host controller lacks enough GPIO pins but the added logic lines do not require frequent high-speed updates. Its 16 outputs and 1 MHz I2C interface can reduce direct pin demand, while reset supports controlled initialization. If outputs must change with very low latency or be driven by high current, a dedicated GPIO or driver may be more appropriate.
Is the PCA9671D suitable for LED control?
The PCA9671D can control LED-related logic and is associated with bus-driven functions that can support PWM dimming in suitable systems. The NXP product information specifically contrasts its 1 MHz I2C speed with the PCF8575 to explain improved support for LED PWM dimming. Confirm individual output current, voltage, and drive-mode limits against the NXP datasheet before driving LEDs.
What is the best drop-in replacement for the PCA9671D?
No independently confirmed drop-in replacement is established by the available cross-reference results. The PCA9671PW is another NXP family member, but its package designation differs from the PCA9671D 24-SO option and must not be treated as a drop-in part without a footprint review. Use the Request a Quote form on this page for an engineering-reviewed replacement assessment.
What is the best equivalent for the PCA9671D?
The closest documented functional equivalent is another member of the NXP PCA9671 family, but no cross-brand equivalent is confirmed as both pin-compatible and parametrically equivalent. A valid substitution must match the 24-SO land pattern, pin functions, reset behavior, I2C address scheme, electrical limits, and output-drive capability. Do not choose a cross-brand device from a generic I/O-expander category match alone.
Where can I buy the PCA9671D online?
Use the Request a Quote form on this page to request the PCA9671D by exact MPN, package, quantity, and delivery target. The form routes the request without requiring a static price or an unsupported stock statement. For production planning, include the required quantity, ship-to region, date code policy, and whether reel, tray, or tube packing is required.
What is the lead time for the PCA9671D?
The current lead time is best obtained through the Request a Quote form on this page using the required quantity and ship-to location. Lead time can vary with order volume, manufacturing capacity, and packaging format, so a generic timing statement would not be reliable. Include your target schedule and acceptable date-code window with the request.
Is the PCA9671D in stock?
Stock should be confirmed through the Request a Quote form on this page for the exact PCA9671D orderable configuration. The form allows quantity, packaging, ship-to region, and delivery-date requirements to be stated clearly. A distributor page showing the family or an ordering suffix does not by itself guarantee inventory for the requested configuration.
What key specifications should engineers know about the PCA9671D?
The key confirmed specifications are 16 I/O outputs, I2C Fast-mode Plus operation, a maximum I2C clock of 1 MHz, reset support, PU configuration, and a 24-pin SO package. The NXP manufacturer datasheet describes it as a remote 16-bit I/O expander for Fm+ I2C-bus operation. Electrical limits, output drive, address range, and temperature ratings should be checked directly in that document.

נתוני עזר הנדסיים עבור PCA9671D — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the PCA9671D when a host controller needs 16 remote logic outputs on an I2C bus running up to 1 MHz and the PCB uses the 24-SO footprint. It is particularly useful for LED indication, relay-command interfaces, sequencing signals, and distributed industrial-control lines where reset behavior matters. The PCA9671PW belongs to the same functional family but uses a different package designation, so it should be selected for a new PCB designed for PW rather than treated as an automatic PCA9671D replacement. For a PCF8575-based design, the PCA9671 family offers a documented upgrade path with faster I2C operation and stronger bus drive, provided the package and pin arrangement are verified. If outputs need continuous high-current capability, galvanic isolation, or guaranteed deterministic timing beyond the remote bus, use a dedicated driver or interface architecture instead.

השוואה עם חלופות

פרמטר מוצר זה
Package 24-SO, 24 pins
Brand NXP Semiconductors
Number of I/O Outputs 16 outputs
I2C Maximum Clock Frequency 1 MHz
Interface Class I2C Fast-mode Plus (Fm+)
Reset Function Yes
Pull-Up Configuration PU
Device Type Remote 16-bit I/O expander

מבדילים עיקריים

  • Sixteen remote outputs in one controller interface (לעומתPCF8575)
  • Higher I2C bus drive capability (לעומתPCF8575)
  • Fast-mode Plus support for compact control (לעומתPCA9671PW)

הערות תכנון

Place the PCA9671D close to the loads it controls to keep output traces short, while routing the I2C SDA and SCL lines away from switching nodes and high-current return paths. The exact I2C pull-up component values must be calculated from bus capacitance, voltage, and the complete device population using the NXP timing guidance. Decoupling placement and values should follow the manufacturer datasheet.

Define the state of all 16 outputs immediately after power-up and after a reset assertion. Firmware and external hardware should agree on whether loads remain off until configuration is valid. Review the output-drive and absolute-maximum limits in the NXP datasheet before connecting loads, especially when the remote interface drives devices outside the PCA9671D's direct current capability.

Do not treat another PCA9671 package option as a drop-in substitute solely because the functional description is similar. The PCA9671D is identified as 24-SO, while PCA9671PW denotes a different package option; verify body size, lead pitch, land pattern, pin numbering, and exposed functionality. Also confirm that the proposed part preserves the required reset behavior, I2C addressing, output modes, and 1 MHz bus performance.

The 1 MHz I2C rate increases timing sensitivity compared with conventional 400 kHz operation. Check bus rise time, pull-up strength, capacitance, and the cumulative loading of every attached device. Avoid long stubs and unnecessary vias, and use continuous ground references beneath the bus routing. Validate the worst-case trace and component tolerances before enabling Fast-mode Plus operation.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

No explicit environmental, automotive, halogen-free, or conflict-minerals status was confirmed in the available records. Apply the required qualification and purchasing criteria before production release.

חיפושים קשורים

PCA9671D datasheet PCA9671D pinout PCA9671D datasheet pdf PCA9671D equivalent PCA9671D replacement PCA9671D cross reference PCA9671D vs PCA9671PW PCA9671D 1 MHz I2C expander PCA9671D 24-SO footprint PCA9671D LED control PCA9671D price PCA9671D stock NXP PCA9671D PCA9671D application circuit

רכיבים ומונחים קשורים

NXP Semiconductors PCA9671D PCA9671PW PCF8575 PCA9671D,118 PCA9671D,112 I/O expander remote I/O expansion I2C Fast-mode Plus Fm+ GPIO PWM dimming 24-SO SOIC-24 surface mount interface IC semiconductor reset input pull-up resistor LED control relay control power sequencing industrial control 1 MHz I2C
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר