מוצרים (44,000+)

PCM56UG4 - 16-Bit Audio DAC | Texas Instruments | 16-SOIC
PCM56UG4

PCM56UG4 - 16-Bit Audio DAC | Texas Instruments | 16-SOIC

The Texas Instruments PCM56UG4 is a 16-bit serial-input audio digital-to-analog converter with a 16-SOIC package, dual supply operation, and a nominal settling time of 1.5 microseconds. It converts serial PCM audio data into an analog output for professional audio, instrumentation, and data-acquisition equipment. The verified product information identifies the converter as a monolithic DAC with a 16-bit resolution and a commercial operating grade. A digital-to-analog converter is a signal-conversion IC that transforms digital PCM data into a continuously variable analog voltage or current. The PCM56UG4 belongs to the DAC family within the broader ADC/DAC and data-converter hierarchy. Its serial interface reduces the number of parallel data lines required, making it suitable for compact audio systems where board area and signal routing are important. The 16-SOIC package is also compatible with conventional surface-mount assembly and tube packaging. The verified data highlights 96 dB dynamic range and maximum total harmonic distortion values of -92 dB at full-scale input and -74 dB at -20 dB input for the K-grade device. These figures make the part relevant to precision audio paths where distortion and noise can affect perceived signal quality. The converter is factory trimmed and tested for critical specifications, according to the available manufacturer datasheet material. The PCM56UG4 uses a factory-trimmed ladder and scaling network with matched analog circuitry. The manufacturer material explains that conversion errors can arise from linearity, matching and tracking behavior, supply rejection, and reference errors. This makes careful power-supply design, grounding, and output-stage implementation important for achieving the rated performance in a finished audio product. Typical applications include digital mixing consoles, professional audio interfaces, audio recording equipment, digital test and measurement systems, and signal-generation equipment. The device can be used where a 16-bit PCM stream must be converted into an analog audio signal while preserving low distortion and adequate dynamic range. Designers should provide clean, symmetrical supply rails and follow the manufacturer’s recommended input, output, and decoupling arrangements. The dual supply requirement must be checked against the target system’s analog rails, while the output network should be designed for the intended load and signal level. The PCM56UG4 should not be selected solely by package and bit depth; interface timing, output amplitude, settling behavior, and system-level noise must also be verified.

RFQ צור קשר
PCM6340QRTVRQ1 - 4-Ch Audio ADC w/ Mic Bias | TI Automotive
PCM6340QRTVRQ1

PCM6340QRTVRQ1 - 4-Ch Audio ADC w/ Mic Bias | TI Automotive

The Texas Instruments PCM6340QRTVRQ1 is an automotive-grade, 4-channel, 32-bit audio analog-to-digital converter (ADC) supporting sample rates from 8 kHz to 768 kHz in a 32-pin WQFN (RTV) 5x5 mm package. The device accepts analog input signals up to 10 V RMS, includes integrated microphone bias generation, and provides input fault diagnostics, making it a single-chip analog front end for in-vehicle audio capture. What is an audio ADC? An audio analog-to-digital converter is a semiconductor that samples continuous analog audio signals and converts them into a digital stream (typically PCM, TDM, or I2S) for downstream DSP, codec, or microcontroller processing. In automotive audio signal chains, audio ADCs sit between the analog microphone or line-input stage and the digital host processor; the broader hierarchy is ADC -> data converter -> mixed-signal IC -> semiconductor. The PCM6340QRTVRQ1 belongs to TI's PCM6xx0-Q1 family of automotive audio ADCs and combines the converter, microphone bias supply, and input diagnostics into one part, which simplifies BOM and PCB area versus discrete implementations. Key features include four high-performance delta-sigma ADC channels with 16/20/24/32-bit output word lengths, support for both single-ended and differential input configurations, integrated programmable microphone bias, and input fault diagnostics (open, short, DC level). The device is controlled through I2C or SPI and outputs audio data over standard serial audio interfaces. It supports line and microphone inputs with input signals up to 10 V RMS. Technically, the PCM6xx0-Q1 family uses a high-order delta-sigma modulator architecture with multi-bit front-end and on-chip digital decimation filtering, achieving high dynamic range and low distortion. The integrated microphone bias regulator eliminates external LDO/charge-pump circuitry, while the input diagnostics monitor each channel for open/short conditions and DC fault levels that are critical for automotive functional-safety requirements. Typical applications include automotive head-unit audio capture, active-noise-cancellation (ANC) and road-noise-cancellation (RNC) microphone arrays, in-cabin voice and hands-free EC/NR front ends, telematics and eCall microphone inputs, and automotive infotainment line-input digitizers. Designers choose this part when they need AEC-Q100-qualified capture with on-chip mic bias and diagnostics to reduce PCB area and improve ASIL-level fault coverage. When designing with this part, follow the datasheet's recommended decoupling scheme and place the analog and digital ground returns per the layout guidelines to meet the stated THD+N and dynamic-range numbers. Use the -enable pin and the configurable power-down modes to manage quiescent draw on accessory-rail battery lines. This page synthesizes distributor pricing, drop-in alternatives from TI's PCM6xx0-Q1 family and competing automotive ADCs, and practical design notes not duplicated in the manufacturer datasheet.

RFQ צור קשר
PDRQL8KCBF12-00 - 16Gb DDR5-7200 DRAM | Samsung
PDRQL8KCBF12-00

PDRQL8KCBF12-00 - 16Gb DDR5-7200 DRAM | Samsung

The Samsung PDRQL8KCBF12-00 is a 16Gb (2Gx8) DDR5 SDRAM device operating at DDR5-7200 data rates, designed for high-performance computing, server, and AI applications. It is a synchronous dynamic random-access memory that provides high bandwidth and low latency, essential for modern processors and accelerators. The device is housed in a standard FBGA package, compatible with JEDEC DDR5 specifications, and operates from a 1.1V core supply. DDR5 SDRAM is the fifth generation of double data rate synchronous dynamic random-access memory, succeeding DDR4. It doubles the burst length to 16 and introduces on-die ECC, improving reliability and performance. DDR5 operates at higher speeds and lower voltages than DDR4, making it suitable for bandwidth-intensive workloads such as data center servers, AI training, and high-end computing. The PDRQL8KCBF12-00 is a key component in memory modules and systems requiring high capacity and speed. Key features include a 16Gb density organized as 2Gx8, a data rate of 7200 MT/s, and a 1.1V supply voltage. It supports on-die ECC, which corrects single-bit errors internally, enhancing data integrity. The device also features a programmable refresh rate, write and read latencies, and a temperature-compensated refresh, ensuring reliable operation across a wide temperature range. The FBGA package provides excellent thermal and electrical performance. Technically, the PDRQL8KCBF12-00 uses a 10nm-class process technology, enabling high density and low power consumption. It incorporates a decision feedback equalizer (DFE) for improved signal integrity at high speeds, and a pseudo-differential DQ interface. The device supports a burst length of 16 and a burst chop of 8, and includes a mode register for configuration. The on-die ECC reduces system-level ECC overhead, improving overall system efficiency. Typical applications include DDR5 memory modules for servers, high-performance computing, AI accelerators, and networking equipment. The high bandwidth and capacity make it ideal for data-intensive tasks such as large-scale data analytics, machine learning inference, and real-time processing. The device is also used in advanced workstations and gaming systems that demand high memory performance. When designing with this device, ensure proper signal integrity by following JEDEC DDR5 layout guidelines, including controlled impedance traces and proper termination. The 1.1V supply should be well-regulated and decoupled with high-frequency capacitors. Thermal management is critical at high data rates; ensure adequate airflow or heatsinking to maintain junction temperature within specified limits. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a comprehensive resource for sourcing and implementing the PDRQL8KCBF12-00.

RFQ צור קשר
PEF20525FV1.3 - Serial Comm Controller SEROCCO-H | Infineon
PEF20525FV1.3

PEF20525FV1.3 - Serial Comm Controller SEROCCO-H | Infineon

The Infineon PEF20525FV1.3 is a SEROCCO-H Serial Optimized Communications Controller IC, designed for high-performance telecommunications applications. It features two independent serial channels and provides advanced PPP/HDLC protocol handling, packaged in a 100-pin TQFP (PG-TQFP-100-3) surface-mount form factor for embedded telecom systems. A Telecom IC (also called a network controller or serial communications controller) is a specialized integrated circuit that offloads data link layer protocol processing from a host CPU. It sits between the physical layer transceiver and the host processor, implementing framing, CRC, and channel management for synchronous serial links. In the system hierarchy, it belongs to the interface IC / network controller & processor category of integrated circuits, enabling deterministic serial data flow in equipment such as ISDN terminal adapters, xDSL modems, and T/E-carrier interface cards. Key features of the PEF20525FV1.3 include two independent serial channels with full-duplex operation, integrated PPP/HDLC framing support, hardware-assisted bit processing for low host CPU overhead, and flexible clocking for T-carrier and E-carrier telecom standards. The device also offers DMA-friendly host interface options and comprehensive interrupt/status reporting, allowing tight integration with embedded host processors. The SEROCCO-H architecture combines dedicated hardware engines for HDLC/PPP framing, CRC generation and checking, and serial channel arbitration. This offloads heavy protocol processing from the host CPU, allowing the host to focus on higher-layer networking tasks. The dual-channel design enables simultaneous handling of two independent serial links, which is valuable for routers, gateways, and multi-port communication equipment. Typical applications include ISDN terminal adapters, xDSL modems, T1/E1 interface cards, frame relay equipment, and embedded telecom modules for factory or industrial networking. The wide protocol support and dual-channel capability make it suitable for any application requiring deterministic serial data link processing. When designing with the PEF20525FV1.3, ensure proper decoupling near the supply pins and follow Infineon's reference layout for the PG-TQFP-100-3 package. The host interface should be configured according to the chosen bus width and endianness to minimize glue complexity. Designers should also verify the latest firmware/driver support matrix from Infineon for their specific host processor family. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר
PEF2256HV2.2 - Quad E1/T1/J1 Framer & LIU | Infineon | MQFP-80
PEF2256HV2.2

PEF2256HV2.2 - Quad E1/T1/J1 Framer & LIU | Infineon | MQFP-80

The Infineon PEF2256HV2.2 (FALC56) is a quad E1/T1/J1 framer and line interface component (LIU) for long- and short-haul telecom applications, housed in an 80-pin P-MQFP-80-1 (Metric QFP) package. It integrates four independent framers and LIU channels on a single die, supporting both North American T1/J1 (1.544 Mbps) and European E1 (2.048 Mbps) PCM hierarchies as well as the H.100/H.110 and H-MVIP digital system highway buses for world-market telecommunication systems. A Line Interface Unit (LIU) is the analog front-end of a TDM telecom system that interfaces between the physical twisted-pair line and the digital PCM backplane. The PEF2256 quad-LIU topology places four such analog interfaces on one chip, allowing one device to terminate an entire T1/E1 quad trunk - reducing board area, BOM count, and power per channel compared with four discrete LIUs. The device belongs to the FALC56 family of framers and line interface components, itself part of the broader framer/line-interface-unit category within telecom interface ICs. Key features include programmable pulse shaping for short-haul and long-haul operation, integrated receive equalization, on-chip jitter attenuator, HDLC controllers per channel, and a flexible parallel micro-controller interface. The device handles both unipolar and bipolar line signalling and provides diagnostic loopback modes (local, remote, payload) per channel. Built-in BERT (Bit Error Rate Test) pattern generation and checking aid field deployment and production test. Typical applications include ISDN PRI (Primary Rate Interface) cards, channel banks, digital cross-connect systems, PBX trunk interfaces, cellular base station backhaul, and multi-port T1/E1/J1 line cards. With four channels per chip, designers can build a 4-port line card with one LIU, simplifying PCB layout and reducing overall system cost. When designing with the PEF2256HV2.2, ensure the analog line-side circuits (transformer, protection, termination) are placed close to the LIU pins to minimize crosstalk between the four on-chip channels. The internal jitter attenuator simplifies clock-recovery design and is configurable per channel via the microcontroller interface. This page synthesizes distributor pricing, drop-in alternatives and practical design notes that complement the manufacturer datasheet. Prices are listed as of 2026-10-09 from authorized distributors.

RFQ צור קשר
PEF24628EV1.2-G - Quad-Channel EFM SHDSL SoC | Infineon
PEF24628EV1.2-G

PEF24628EV1.2-G - Quad-Channel EFM SHDSL SoC | Infineon

The Infineon PEF24628EV1.2-G is a quad-channel EFM (Ethernet First Mile) Symmetrical High-bit-rate Digital Subscriber Line (SHDSL) transceiver System-on-Chip, integrating four independent SHDSL channels with on-chip HDLC controllers, serializer/deserializer (SerDes) interfaces, and an embedded management interface. The part is housed in a PG-LBGA-324-2 (324-pin low-profile BGA) package and operates from 1.5 V core and 3.3 V I/O supply rails. It supports the full SHDSL.bis (G.991.2) standard for symmetric DSL transmission over 2-wire copper pairs, enabling EFM bonding for aggregated multi-pair Ethernet services at the customer premises and central office. A System-on-Chip (SoC) in the telecom interface category is a highly integrated device that combines a CPU subsystem, multiple dedicated protocol engines, and a flexible host interface on a single silicon die. The PEF24628 belongs to the SHDSL/EFM transceiver SoC family, which sits hierarchically under: telecom interface IC -> wired broadband transceiver -> xDSL transceiver -> SHDSL front-end SoC. The device historically originated from the Lantiq product line, which Infineon acquired and now sells as part of its wireline communications portfolio. Key features include four independent SHDSL channels, support for EFM bonding (G.998.1), on-chip HDLC controllers, parallel and serial host interfaces, low-jitter PLL clock synthesis, and integrated line driver interface logic. The HDLC engine, parallel/serial host ports, and flexible interrupt structure minimize the burden on the external host CPU in a DSLAM line card or CPE modem design. The architecture is built on a mature 0.13 um CMOS process with mixed-signal analog front-end circuitry for the SHDSL line interface. The part includes dedicated per-channel DSP engines for SHDSL symbol processing, echo cancellation, and trellis coding. Internal SRAM buffers per channel help absorb latency variation on the host bus, and the SerDes block supports multi-channel aggregation to a framer/backhaul device. Typical applications include SHDSL.bis line cards in DSLAMs, multi-pair bonded EFM Ethernet modems, four-wire industrial DSL links, and legacy E1/T1 extension infrastructure over copper. The quad-channel density makes it a strong fit for small-form-factor CPE MDU/MTU aggregation where four bonded pairs are needed. Design consideration: pay close attention to the PG-LBGA-324-2 PCB land pattern, controlled-impedance differential routing for the SHDSL line pairs, and proper thermal management - the device dissipates significant power when all four channels are active. Reference Infineon design notes for the recommended magnetics, line protection, and host-IF timing budget. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
PEF2466HV2.2 - 4-Ch SICOFI Codec/Filter POTS | Infineon
PEF2466HV2.2

PEF2466HV2.2 - 4-Ch SICOFI Codec/Filter POTS | Infineon

The Infineon PEF2466HV2.2 is a four-channel Signal Processing Codec/Filter (SICOFI-4-µC) IC designed for Plain Old Telephone Service (POTS) line interfacing in central-office and carrier-class equipment. Housed in a P-MQFP-64-1 (64-pin Metric Quad Flat Pack) package, this telecom IC integrates four independent codec/filter channels with programmable gain, A-law/µ-law companding, and on-chip hybrid balance networks, making it a logical continuation of the well-established Siemens/Infineon SICOFI programmable codec-filter family. A codec/filter IC is a mixed-signal device that performs the analog-to-digital and digital-to-analog conversion plus the band-limiting transmit/receive filtering required to interface voice-band (300 Hz to 3.4 kHz) analog telephone lines to a digital PCM/TDM backplane such as an E1/T1 link. Within the system hierarchy, it sits between the line-side SLIC (Subscriber Line Interface Circuit) and the system-side PCM highway controller, occupying the role of a per-channel voice-band data pump in the access network. Key features include four fully independent codec/filter channels with 16-bit linear or 8-bit A-law/µ-law companded PCM coding, programmable transmit and receive gain/attenuation in 0.1 dB steps, on-chip hybrid-balance and anti-alias filters, and a serial µC or SPI control interface. The device targets 3.3 V/5 V digital supplies and a +/-5 V analog supply, supporting extended industrial temperature grades typical for outdoor or remote-cabinet telecom deployments. Architecturally, the PEF2466HV2.2 uses a sigma-delta conversion front-end per channel with dedicated switched-capacitor filters, providing flat group delay across the voice band and very low total harmonic distortion. The integrated µC interface allows per-channel gain calibration and channel-by-channel A-law/µ-law selection, eliminating external DSP overhead for companding and gain control. Typical applications include 4-channel POTS line cards in central-office switches, integrated access devices (IADs), digital loop carrier (DLC) systems, VoIP media gateways with FXS ports, and PBX line interface modules where four voice channels must be terminated in a single low-footprint device. When designing with the PEF2466HV2.2, careful attention must be paid to analog/digital ground partitioning, the PCM clock and frame-sync timing relationship, and the decoupling of the +/-5 V analog rails. The part is now in long-term supply under the Infineon (formerly Lantiq) telecom portfolio, and procurement should be planned against documented last-time-buy milestones where applicable. This page synthesizes distributor pricing, family-mate and same-package alternatives, and practical interface-design notes that complement the manufacturer datasheet with sourcing and migration context.

RFQ צור קשר
PEX8509-AA25BI - 8-Lane 8-Port PCIe Switch | Broadcom
PEX8509-AA25BI

PEX8509-AA25BI - 8-Lane 8-Port PCIe Switch | Broadcom

Broadcom PEX8509-AA25BI is an eight-lane, eight-port PCI Express switch conforming to PCI Express Base Specification Revision 1.1, with integrated 2.5 Gbps SerDes and a 196-ball PBGA package measuring 15 mm by 15 mm. Its eight-lane PCIe switch architecture routes traffic among multiple endpoints while supporting scalable, non-blocking interconnect designs. The device is identified as a low-power ExpressLane PCIe switch suitable for communications equipment, consumer products, servers, and storage systems. A PCI Express switch is a semiconductor within the interface-controller and connectivity hierarchy. It manages transaction traffic between a host or upstream PCIe port and downstream devices, allowing one system bus to serve several endpoints. The PEX8509-AA25BI supports PCIe Gen 1 operation at 2.5 Gbps per lane, provides up to eight ports, and uses integrated SerDes to connect PCIe links to the switching fabric. Its flexible configuration is intended to broaden system connectivity without requiring a separate switch for each endpoint. The primary feature of this part is its combination of eight PCIe lanes and eight ports in one package. Broadcom describes the PEX 8509 as a low-power switching solution with typical power consumption of 1.2 W. That operating point makes it relevant to space-conscious embedded and communications platforms where link breadth, board area, and power budget all influence product selection. The device supports non-blocking interconnect architectures used in scalable storage and communication equipment. Technical implementation centers on the integrated SerDes interfaces and PCIe switch fabric. A Gen 1 link operates at 2.5 Gbps, while the switch coordinates traffic arriving from the upstream host and distributing requests to downstream endpoints. Designers must account for lane-to-port mapping, reference-clock requirements, transmitter equalization, receiver configuration, power sequencing, and the high-speed layout constraints of a 196-ball PBGA device. These considerations make careful reference-design review essential before schematic capture or PCB routing. Typical uses include external storage controllers, server expansion systems, embedded communication platforms, consumer networking equipment, and industrial systems that need multiple PCIe endpoints behind one host connection. The switch is particularly relevant when adding endpoint capacity without redesigning the entire host interface around individual downstream controllers. A central design consideration is PCB implementation. The 15 mm by 15 mm BGA requires controlled escape routing, a multilayer board with suitable high-speed stack-up, length matching where required, and a power delivery network capable of supporting approximately 1.2 W typical device power while maintaining acceptable voltage behavior at the ball grid. This product summary consolidates the Broadcom architecture information, package characteristics, application fit, replacement assessment, comparison fields, and implementation guidance needed to evaluate the PEX8509-AA25BI before committing it to a PCI Express switch design.

RFQ צור קשר
PEX8533-AA25BI - 32-Lane Gen2 PCIe Switch | Broadcom
PEX8533-AA25BI

PEX8533-AA25BI - 32-Lane Gen2 PCIe Switch | Broadcom

Broadcom PEX8533-AA25BI is a 32-lane PCI Express Gen2 switch with an integrated SerDes and up to six configurable ports, supplied in a 680-pin 35 mm FPBGA package. It provides typical power consumption of 3.3 W and is pin compatible with the PEX8532, making it a flexible PCIe routing device for systems that need to fan out multiple PCIe links. A PCI Express switch is a semiconductor device that routes high-speed serial transactions between a root complex, endpoint devices, and other PCIe components. Within the broader hierarchy of interface ICs, PCI Express controllers, and bus controllers, the PEX8533 consolidates multiple lanes into configurable downstream paths. Its integrated SerDes reduces the need for separate transmit and receive PHY components while supporting system-level PCIe port expansion. The switch offers 32 total PCIe lanes and as many as six configurable ports. This combination allows designers to implement systems with multiple endpoint devices, downstream switch structures, or adapter arrangements. Its typical power of 3.3 W is the central thermal figure for board-level planning, while the 680-ball package requires careful high-speed layout, power delivery, and thermal-management techniques. The PEX8533 uses a 35 mm square FPBGA package with 680 terminals. Such a fine-pitch package can provide dense interconnect capacity for high-speed SerDes routing, but it also demands multilayer PCB construction, constrained escape routing, accurate impedance control, and assembly-process capability for the selected package technology. Production designs should follow the manufacturer’s reference layout and evaluation-platform guidance. Typical applications include PCIe expansion systems, high-end server and workstation platforms, storage controllers, accelerator systems, media-processing equipment, and embedded test systems. The six-port configuration is useful where one upstream PCIe connection must feed several downstream endpoint links without relying on separate switch silicon for every branch. Thermal design is essential because the stated typical power is 3.3 W. Board copper, adjacent power circuitry, airflow, and the surrounding enclosure can all influence junction temperature. High-speed differential pairs should use the manufacturer’s recommended layer stack, geometry, and via structures, while power and ground planes require carefully controlled return paths. This page consolidates the available technical facts into an application-oriented guide covering package constraints, thermal considerations, PCIe routing, configuration, and replacement qualification. The PEX8533-AA25BI-G ordering code is identified as a same-package manufacturing variant, while broader functional upgrades are kept outside the strict drop-in replacement list because their packages and configurations differ.

RFQ צור קשר
PEX8603-AB50NI - Gen 2 PCIe Switch, 3 Lanes | Broadcom
PEX8603-AB50NI

PEX8603-AB50NI - Gen 2 PCIe Switch, 3 Lanes | Broadcom

The Broadcom PEX8603-AB50NI is a PCI Express Gen 2 switch IC with three lanes, three ports, and three switch channels, housed in a 136-aQFN package measuring 10 x 10 mm. It is designed to add scalable, high-bandwidth, non-blocking interconnection to control-plane, consumer, and embedded systems. The Broadcom PEX 8605 Product Brief describes the ExpressLane PEX8603 as a device suited to fan-out and peer-to-peer connectivity. An operating specification summary identifies the PEX8603-AB50NI as a three-lane, three-port, PCIe Gen 2 switch. Its three-lane architecture allows a host-facing connection and multiple downstream links to share a PCIe link budget when the system topology permits it. This makes the device useful in systems that require an additional PCIe routing layer without relying on a multi-tier switch hierarchy. The 136-aQFN package provides 136 electrical contacts in a compact 10 x 10 mm outline. The high pin count supports the power, ground, high-speed differential lanes, configuration, auxiliary, and control functions normally required by a multi-port PCIe switch. Exact lane assignments, auxiliary signaling support, and pin-level power requirements must be taken from the Broadcom pin-description table before PCB routing begins. PCIe Gen 2 operation supports 5 GT/s signaling per lane, a standard defined for the PCIe generations supported by this switch family. The three-port topology can serve embedded controllers, storage controllers, network interfaces, endpoint devices, and display or capture subsystems that communicate through a common PCIe fabric. The non-blocking architecture allows compatible endpoints to transfer data concurrently rather than sharing a single serialized path. System designers should allocate reference-clock, auxiliary, and power-delivery resources according to the manufacturer application schematic. Decoupling must follow the recommended values and placement shown in the Broadcom reference design, because switch regulators and high-speed receivers can be sensitive to supply noise and return-path discontinuities. Layer-stackup, trace-length matching, and via geometry also control insertion loss and skew across the differential lanes. This page consolidates the verified product identity, package information, topology details, sourcing paths, and engineering guidance for the PEX8603-AB50NI. It also identifies drop-in ordering representations supported by the available documentation and distinguishes them from functional but non-pin-compatible PCIe switch options.

RFQ צור קשר
PEX8603-AB50TQIG - 3-Lane PCIe 2.0 Switch | Broadcom
PEX8603-AB50TQIG

PEX8603-AB50TQIG - 3-Lane PCIe 2.0 Switch | Broadcom

The Broadcom PEX8603-AB50TQIG is a three-lane, three-port PCI Express Gen 2.0 switch IC designed to add scalable, non-blocking interconnection between PCI Express devices and a host or root complex. It supports PCI Express Gen 2.0 operation, provides three lanes and three ports, and is associated with a 128-pin TQFP package measuring 14 mm by 14 mm. The device is positioned for control-plane, consumer, embedded, fan-out, and peer-to-peer systems requiring flexible PCIe connectivity. A PCI Express switch is an interface IC within the PCIe semiconductor hierarchy. It accepts traffic arriving on one or more upstream or downstream lanes and routes transactions among multiple endpoints. The PEX8603's three-lane, three-port architecture consolidates several PCIe links behind a single switching fabric, reducing system-level routing complexity while preserving the non-blocking interconnection emphasized in the Broadcom product overview. The principal feature of the PEX8603-AB50TQIG is its PCI Express Gen 2.0 switching capability across a three-lane, three-port configuration. This arrangement makes the switch suitable for systems that need to fan out traffic to multiple PCIe devices or establish peer-to-peer links. Its 128-TQFP surface-mount package supports compact integration on multilayer PCBs, while the exact lead geometry, pin functions, and exposed thermal provisions must be confirmed in the manufacturer pin-description table before layout release. Operationally, the PEX8603 acts as a configurable connectivity point within a PCIe topology rather than as a storage controller, processor, or conventional analog interface. System designers must account for lane allocation, endpoint configuration, reference-clock requirements, reset behavior, power sequencing, and the device's upstream or downstream role. The product overview identifies the device as a Broadcom offering for high-performance computing and efficient data-connectivity applications. Typical uses include embedded systems that connect an SoC or host processor to multiple peripherals, control-plane platforms requiring ordered PCIe expansion, and consumer systems that add multiple endpoint devices without routing each link directly to the root complex. The PEX8603 can also support fan-out and peer-to-peer architectures where independent downstream devices benefit from centralized switch management. PCB implementation requires exact pin-by-pin assignment from the manufacturer datasheet, differential-pair routing for PCI Express lanes, continuous reference planes, suitable decoupling, and controlled-length routing between the switch and connectors or endpoints. Power integrity and thermal design should be evaluated across worst-case traffic and ambient conditions. Do not infer exposed-pad connectivity or pin names from a generic TQFP symbol. This page consolidates the verified PCIe configuration, package information, sourcing path, and practical replacement criteria for engineers evaluating the PEX8603-AB50TQIG. A drop-in alternative must preserve the same package, pinout, electrical functions, lane organization, firmware expectations, and system configuration; a device sold as a generic PCIe switch is not automatically interchangeable.

RFQ צור קשר
PEX8604-BA50BC - 4-Lane 4-Port PCIe Gen 2 Switch | Broadcom
PEX8604-BA50BC

PEX8604-BA50BC - 4-Lane 4-Port PCIe Gen 2 Switch | Broadcom

Broadcom PEX8604-BA50BC is a PCI Express switch IC with four Gen 2 lanes, support for as many as four ports, a 5.0 GT/s signaling rate, and a 196-BGA package measuring 15 mm by 15 mm. The device conforms to revision 2.0 of the PCI Express Base Specification and is designed to let one host connection fan out to multiple PCI Express endpoints. It is positioned as a compact fabric switch for consumer, embedded, and industrial systems requiring more PCIe connectivity than a root complex can provide directly. A PCI Express switch is a semiconductor that creates a point-to-point switching fabric between a host or upstream controller and multiple downstream endpoints. Within the hierarchy of interface ICs, PCI Express switches sit below multiport I/O controllers, above individual endpoint devices, and within the broader semiconductor and computer-interface ecosystem. Unlike a simple analog multiplexer, the PEX8604-BA50BC arbitrates high-speed serial transactions, manages lane-level routing, and coordinates PCIe configuration and power-management behavior. The principal features are four Gen 2 lanes, up to four ports, 5.0 GT/s per lane, and compliance with the PCI Express Base Specification revision 2.0. Its 196-BGA package supports compact integration without requiring a large peripheral bridge. The Broadcom product family is also identified as RoHS3 compliant, making it suitable for designs that apply lead-free electronic-component requirements. Exact auxiliary supply voltages, maximum power dissipation, reference clock requirements, and operating-temperature limits should be confirmed in the manufacturer data book before schematic release. The ExpressLane architecture separates PCIe traffic among downstream ports while preserving the packet-based, full-duplex character of PCI Express. In a typical system, the upstream port connects to a root complex or another switch, while downstream ports connect to NVMe controllers, network controllers, capture devices, or FPGA-based endpoint cards. Proper lane allocation, reference-clock distribution, reset sequencing, and power-rail ordering remain essential for reliable operation. System designers should also use the data-book reference design as the basis for connector, via, and return-path implementation. Typical uses include compact workstation and server add-in cards, embedded control systems, test and measurement platforms, storage adapters, and industrial computers. Because Gen 2 signaling provides 5.0 GT/s per lane, the switch is most appropriate for endpoint traffic that fits within the available aggregate link bandwidth. Applications requiring newer PCIe generations should not assume forward compatibility without an explicit engineering review. For layout, place the switch and its decoupling network close to the power and ground planes, minimize high-speed stub lengths, and route each PCIe lane as a controlled-impedance differential pair. Follow the Broadcom reference design for ball assignments, layer transitions, connector launches, and clock routing. Confirm package-ball details and unused-ball treatment from the current manufacturer documentation rather than inferring them from the 196-BGA outline. This product page combines the confirmed PCIe configuration and package information with application guidance, alternative-device comparisons, and practical design considerations. It is intended to help engineers identify the correct switch and plan its integration while keeping unconfirmed electrical details and replacement decisions tied to the manufacturer data book and device-specific validation.

RFQ צור קשר
PEX8604-BA50BI - 4-Lane Gen 2 PCIe Switch | Broadcom
PEX8604-BA50BI

PEX8604-BA50BI - 4-Lane Gen 2 PCIe Switch | Broadcom

The Broadcom PEX8604-BA50BI is a PCI Express switch integrated circuit built around the ExpressLane PEX8604 architecture. It provides four PCI Express Gen 2 lanes operating at 5.0 GT/s and supports up to four downstream ports in a 196-BGA package measuring 15 mm by 15 mm. The device conforms to revision 2.0 of the PCI Express Base Specification. This combination makes it a compact PCIe routing solution for systems that need to connect multiple PCI Express endpoints to a host interface. A PCI Express switch is a semiconductor that creates additional PCIe links between a root complex or another switch and multiple endpoint devices. It operates within the PCIe hierarchy as a bridge and switch rather than as an endpoint itself. The PEX8604 belongs to the broad PCIe switch and bridge category, which supports fan-out, embedded systems, consumer equipment, and high-availability platforms where downstream devices must communicate with a central host. The principal device characteristics are four Gen 2 lanes, a maximum of four ports, and a 5.0 GT/s per-lane signaling rate. Broadcom describes the PEX8604 as its smallest four-lane Gen 2 device. The switch also supports PCIe hot-plug functionality for supported downstream configurations, making it relevant to systems where expansion modules are replaced or maintained without powering down the complete platform. The 196-BGA package provides a high pin count for power, ground, high-speed transmit and receive paths, configuration interfaces, reference clocks, and control signals. Such a package also places substantial emphasis on compact board area. Achieving correct Gen 2 operation therefore requires careful PCB layer planning, controlled impedance routing, uninterrupted reference planes, and power-delivery design that meets the device's low- and high-speed requirements. Typical uses include embedded computing platforms, consumer appliances, PCI Express endpoint aggregation, expansion systems, and high-availability equipment with hot-pluggable modules. In these systems, the switch expands one host-facing PCIe connection into multiple downstream links while allowing port-level routing and monitoring functions according to the device configuration. A primary design consideration is signal integrity. The 5.0 GT/s interface requires short, impedance-controlled routes, solid reference planes, suitable via transitions, and connector or package escape geometry designed for low loss. Power sequencing, clock distribution, reset behavior, and the firmware-supported link configuration must also be validated together; satisfying individual data-sheet limits in isolation does not guarantee stable operation across every board stack-up and temperature condition. This product overview synthesizes the manufacturer capabilities, package information, cross-reference findings, and practical implementation considerations into an engineering-focused guide. It also distinguishes documented characteristics from parameters that still require confirmation from the full technical documentation before a new board design is released.

RFQ צור קשר
PEX8605-AB50NI - 4-Lane PCIe Gen 2 Switch | Broadcom
PEX8605-AB50NI

PEX8605-AB50NI - 4-Lane PCIe Gen 2 Switch | Broadcom

The Broadcom PEX8605-AB50NI is a PCI Express Gen 2 switch IC with four lanes, four ports, and a 136-aQFN package measuring 10 x 10 mm. It is designed for embedded, industrial, consumer, and embedded-system designs that require PCIe connectivity beyond the capabilities of a root complex or endpoint device. A PCI Express switch is a semiconductor device that expands one PCIe interface into multiple downstream links while managing packet traffic between a host or upstream endpoint and connected peripherals. The PEX8605-AB50NI uses a non-blocking internal switch architecture, supports packet cut-through, and provides full line-rate operation on its ports in supported configurations. The switch supports PCIe Gen 2 operation with four lanes and four ports. In an x1-to-x1 configuration, the manufacturer documentation identifies a maximum latency of 250 ns. Packet cut-through reduces the time packets remain in the switch, while the non-blocking architecture allows multiple ports to operate concurrently. These characteristics make the device useful for systems needing additional PCIe endpoints without changing the host-side system architecture. The PEX8605-AB50NI is suitable for embedded computing, industrial controllers, test equipment, storage systems, communications equipment, and consumer appliances requiring multiple PCIe connections. Its 10 x 10 mm aQFN package supports compact board layouts, but high-speed PCIe routing requires careful controlled-impedance layout, solid reference planes, and close decoupling. The primary design consideration is signal integrity. PCIe differential pairs should be routed as controlled-impedance transmission lines with minimal stubs and discontinuities, while power and ground distribution should provide low-impedance return paths. The 136-aQFN package also requires careful thermal and assembly planning because its fine-pitch lead arrangement complicates rework and demands a suitable land pattern. This product page combines the manufacturer architecture information with distributor listings and practical integration guidance. It distinguishes verified capabilities from parameters that require confirmation from the complete Broadcom datasheet, helping engineers evaluate the PEX8605-AB50NI for a new embedded or industrial platform.

RFQ צור קשר
PEX8605-AB50TQIG - 4-Lane PCIe Gen 2 Switch | Broadcom
PEX8605-AB50TQIG

PEX8605-AB50TQIG - 4-Lane PCIe Gen 2 Switch | Broadcom

Broadcom PEX8605-AB50TQIG is a PCI Express Gen 2 switch with four lanes, four ports, packet cut-through, and a maximum latency of 250 ns in an x1-to-x1 configuration. The device is manufactured using Renesas 90 nm process technology and is assembled in a lead-free 14 x 14 mm exposed-pad TQFP package with 128 pins. A PCI Express switch is a semiconductor that connects a PCI Express host or endpoint to multiple downstream devices. It belongs to the interface IC hierarchy, where PCIe fabric switching, lane multiplexing, and packet forwarding reduce the number of system expansion interfaces required by a motherboard or embedded platform. The PEX8605 therefore serves as infrastructure between a root complex and attached PCIe devices. The switch provides four Gen 2 lanes and four ports, with full line-rate operation on all ports. Its non-blocking internal switch architecture and packet cut-through capability are designed for high-throughput, low-latency systems. Broadcom identifies consumer and embedded applications as suitable low-power operating environments, while the device is also associated with server, storage, networking, and enterprise equipment. The PEX8605 architecture supports packet cut-through rather than store-and-forward operation, which is the central technical reason for its stated 250 ns maximum latency in x1-to-x1 use. A non-blocking fabric allows traffic associated with multiple ports to progress without a shared internal bottleneck, provided the upstream and downstream links are correctly provisioned and the configuration limits are respected. Typical deployments include redundant storage paths, multi-port network adapters, embedded systems requiring PCIe expansion, and server platforms that need several PCIe connections behind one host interface. In each case, port configuration, lane width, reference-clock requirements, reset behavior, and thermal performance must be validated against the complete system design. The principal design consideration is package-aware PCB implementation. The 128-pin exposed-pad TQFP footprint requires careful escape routing, uninterrupted input and output reference planes, and adequate thermal copper beneath the exposed pad. Power sequencing and signal-integrity verification are equally important because simultaneous high-speed traffic can expose return-path and supply-noise problems. This product overview combines Broadcom architecture details, package and process information, verified commercial availability, and practical integration considerations. It also distinguishes true replacement requirements from superficially similar PEX8605 order codes, helping engineers confirm pin compatibility, package construction, lane configuration, and application suitability before committing a PCB design.

RFQ צור קשר
PEX8606-BA50BC - 6-Lane Gen 2 PCIe Switch | Broadcom
PEX8606-BA50BC

PEX8606-BA50BC - 6-Lane Gen 2 PCIe Switch | Broadcom

Broadcom PEX8606-BA50BC is a six-lane, six-port PCI Express switch operating at 5.0 GT/s for PCI Express Generation 2 systems. The device is associated with a commercial-temperature grade and a 196-ball BGA package measuring 15 x 15 mm. It provides up to six PCIe downstream ports, with each lane supporting 5.0 GT/s signaling. A PCI Express switch is a semiconductor device that expands one host-facing PCIe connection into multiple endpoint-facing links. Within the system hierarchy, the PEX8606-BA50BC is a PCIe interface switch, interface controller, bus controller, and power-management IC used to manage high-speed serial data transfer. Its six-lane architecture allows multiple downstream functions to share a host PCIe link while maintaining independent port connections. Broadcom documents compliance with PCI Express Base Specification r2.0 and backward compatibility with PCI Express Base Specification r1.1 and r1.0a. Each port supports auto-negotiation, lane reversal, and polarity reversal. These functions help system integrators simplify configuration around lane assignments and improve interoperability with PCIe devices that implement different physical-layer conventions. The switch is intended for embedded control-plane and packet-processing equipment, where a host processor or accelerator must connect to multiple PCIe endpoints. Its 196-terminal square BGA construction provides dense interconnect capacity for power rails, reference signals, configuration interfaces, and six high-speed port groups. Ball-grid packaging requires careful PCB escape routing and a land pattern based on the manufacturer package drawing. Typical applications include embedded network modules, packet-processing systems, storage controllers, server add-in cards, and industrial PCIe expansion platforms. For compact embedded equipment, the switch can consolidate several endpoint links behind a single host connection. In larger systems, designers must account for connector reach, insertion loss, clock topology, reference-clock quality, and thermal performance when routing 5.0 GT/s signals. The primary design consideration is PCB implementation rather than regulator-style heat management. Use the manufacturer land pattern, controlled-impedance routing rules, and recommended ball assignments, and preserve continuous return paths beneath high-speed differential pairs. Validate power sequencing, reference clocks, reset behavior, and downstream-port firmware configuration before releasing the design. This product record combines the manufacturer product overview, exact package and channel details, PCI Express capabilities, lifecycle information, and verified distribution sources. It also provides application guidance, engineering design notes, sourcing instructions, and a strict assessment of replacement candidates without presenting unverified substitutes as drop-in devices.

RFQ צור קשר
PEX8606-BA50BI - 6-Lane Gen 2 PCIe Switch | Broadcom
PEX8606-BA50BI

PEX8606-BA50BI - 6-Lane Gen 2 PCIe Switch | Broadcom

Broadcom PEX8606-BA50BI is a PCI Express switch IC with six lanes, six ports, and PCIe Gen 2 operation, housed in a 196-pin PBGA measuring 15 x 15 mm. It is designed for systems that require multiple PCIe endpoints to share a host interface through a dedicated PCIe switch. Each port supports automatic negotiation, lane reversal, and polarity reversal, improving compatibility with installed cards and cable-connected equipment. A PCI Express switch is an interface IC within the broader semiconductor and computer-interface hierarchy. It routes PCIe traffic among a host or root complex, endpoint devices, and other system resources. By expanding one upstream link into multiple downstream ports, the PEX 8606 can simplify board topology in embedded control systems, packet-processing equipment, storage systems, and test platforms while maintaining protocol-level link management. The documented configuration provides six PCIe lanes, six switch ports, two channels, and full PCI Express Base Specification Revision 2.0 compliance. The switch is backward compatible with PCI Express Base Specification Revision 1.1 and Revision 1.0a. Automatic lane-width negotiation allows devices to operate at a speed and width supported by both ends of the link, while lane and polarity reversal add practical tolerance for connector orientation and routing differences. The PEX 8606 architecture is intended for embedded control-plane designs, including packet-processing modules. Its principal engineering benefit is the elimination of multiple host-to-endpoint paths when several PCIe devices must communicate through one system controller. Supporting both current Gen 2 operation and earlier PCIe generations makes it useful when the system must accommodate older endpoint cards or transition from legacy expansion equipment to newer PCIe implementations. Typical applications include industrial packet routers, embedded control modules, network-interface assemblies, storage controllers, instrumentation platforms, and compact computing systems requiring multiple PCIe connections. The 196-pin PBGA supports high-speed, dense board layouts, but its 15 x 15 mm footprint requires careful ball assignment, multilayer routing, reference-plane continuity, and power-distribution design to preserve signal integrity across all six lanes. When integrating the device, plan the board with the Broadcom reference design and pin-assignment documentation, maintain continuous return paths beneath high-speed links, and validate power sequencing across the host and downstream ports. The broad compatibility features reduce link-training risk, but they do not replace proper reference-plane design, connector configuration, or system-level PCIe compliance testing. This product page consolidates the Broadcom PEX 8606 architecture, compatibility features, application guidance, package information, and engineering-oriented replacement analysis to help designers evaluate the switch before beginning a dense PCB implementation.

RFQ צור קשר
PEX8608-BA50BC - 8-Lane Gen 2 PCIe Switch | Broadcom
PEX8608-BA50BC

PEX8608-BA50BC - 8-Lane Gen 2 PCIe Switch | Broadcom

Broadcom PEX8608-BA50BC is a PCI Express switch IC with eight Gen 2 lanes at 5.0 GT/s, configurable into up to eight flexible ports, and a 196-PBGA package measuring 15 x 15 mm. It conforms to PCI Express Base Specification revision 2.0 and uses packet cut-through to minimize transfer delay. A PCI Express switch is a semiconductor that routes high-speed serial transactions between a host or upstream endpoint and multiple downstream devices. Within the PCI Express hierarchy, this device is a PCIe switch, a fabric-based interface IC, and a system-level connectivity component. Eight SerDes lanes can be partitioned among several ports, allowing one compact system to aggregate endpoints for communications, control-plane, embedded, storage, and peer-to-peer equipment. The PEX 8608 provides non-blocking internal switching, two virtual channels for traffic prioritization, and full line-rate operation on configured ports. Broadcom describes packet cut-through latency as 140 ns for an x4-to-x1 configuration in its product-page summary and as up to 130 ns in the linked feature documentation. SerDes outputs can be software-controlled for power reduction and signal-strength optimization. Power management follows the PCI Express power-management specification. Unused SerDes physical links can be switched off to reduce power consumption, while controllable SerDes outputs allow system software to tune operating conditions. The switch architecture supports flexible port configurations, virtual-channel traffic separation, and scalable aggregation without relying on an external switch fabric for each endpoint connection. Typical deployments include communications platforms, embedded systems, backplane aggregation, industrial controllers, test equipment, and servers that need additional PCIe endpoints. The eight-port capability makes it useful where several endpoint types, link widths, or downstream devices must share a compact host interface while retaining deterministic low-latency routing. Design the PCB with the manufacturer’s 196-PBGA land pattern, high-speed differential routing rules, reference-plane continuity, and decoupling recommendations. Validate lane configuration, firmware or register programming, auxiliary power sequencing, and thermal performance across the intended traffic profile before production release. The exact pin assignments and electrical limits must be taken from the pin-description table in the manufacturer datasheet. This page consolidates the official product architecture, package information, Gen 2 link capability, application fit, and practical implementation considerations. It also distinguishes confirmed drop-in coverage from broad functional equivalents, helping engineers determine whether a candidate can be soldered onto the same PCB land pattern rather than merely serving a similar PCIe-switch function.

RFQ צור קשר
PEX8609-BA50BC - 8-Lane 8-Port PCIe Switch | Broadcom
PEX8609-BA50BC

PEX8609-BA50BC - 8-Lane 8-Port PCIe Switch | Broadcom

Broadcom PEX8609-BA50BC is an eight-lane, eight-port PCI Express switch integrated in a 196-ball PBGA package measuring 15 x 15 mm. It provides an integrated 5.0 GT/s SerDes interface, configurable PCIe ports, and typical power consumption of 1.60 W. The device is designed for systems that need to fan out PCIe connectivity while maintaining a Gen 2-class serial interface. A PCI Express switch is a semiconductor that bridges one host or upstream PCIe link with multiple downstream endpoints. It belongs to the interface IC hierarchy, where PCIe controllers and switches manage high-speed serial data transfer between processors, adapters, storage devices, and expansion cards. The PEX8609 is intended to expand connectivity in systems where direct routing from a root complex to every endpoint would be impractical. The PEX8609 supports up to eight configurable ports and provides eight integrated SerDes channels operating at 5.0 GT/s. Its feature set includes support for Access Control and compatibility with PCI Express Base Specification 2.0, including backward compatibility with PCIe 1.0a and 1.1. PCI Power Management Specification 1.2 support is also identified for the device, enabling participation in system power-management states. The PEX8609-BA50BC combines a multiport switching architecture with a compact 196-ball PBGA package. Its 15 x 15 mm body supports compact embedded and expansion systems, while the exposed-ball construction facilitates board-level routing and inspection under assembly processes designed for fine-pitch BGAs. The listed typical power of 1.60 W makes power budgeting an important part of switch-board design. Typical applications include PCI Express storage enclosures, multi-port accelerator systems, embedded computing platforms, carrier boards, and host systems that must connect several PCIe endpoint devices through a single upstream link. The eight configurable ports can simplify system topology when endpoint discovery, peer-to-peer routing, or downstream fan-out is required. Layout should prioritize short, impedance-controlled SerDes connections, solid reference-plane continuity, and clean separation between high-speed and power-return paths. Thermal design should account for the 1.60 W typical device power together with adjacent circuitry. Decoupling and power-distribution networks should follow the layout and capacitor guidance in the manufacturer data book. This product record combines the manufacturer data-book characteristics with practical application, package, comparison, and design guidance. It also highlights the limits of drop-in sourcing: only the closely related PEX8609-BA50BI G was identified with sufficient evidence to describe a same-package replacement, while generic cross-reference tools did not establish additional pin-compatible devices.

RFQ צור קשר
PEX8609-BA50BI - 8-Lane 8-Port PCIe 2.0 Switch | Broadcom
PEX8609-BA50BI

PEX8609-BA50BI - 8-Lane 8-Port PCIe 2.0 Switch | Broadcom

Broadcom PEX8609-BA50BI is an eight-lane, eight-port PCI Express switch IC supporting PCIe 2.0, with a maximum data rate of 4.0 GB/s and a listed power value of 1.60 W. The device is identified in a 196-pin PBGA package measuring 15 x 15 mm and is categorized as a PCI Express switch with DMA capability. Its position within the PCI Express interface hierarchy makes it suitable for systems that require one upstream PCI Express link to be expanded across multiple downstream endpoints. A PCI Express switch is a semiconductor that manages point-to-point serial links between a host or root complex and one or more peripherals. Unlike a conventional parallel bus switch, a PCIe switch operates with serialized differential lanes and transaction-based packet transfer. The PEX8609 combines eight lanes and eight ports in one integrated device, allowing compatible endpoints to share a higher-level interconnect while each link retains protocol-managed flow control and configuration through PCIe. The principal identified features are PCIe 2.0 operation, support for eight lanes, eight ports, a 4.0 GB/s maximum data rate, and DMA functionality. These characteristics place the PEX8609 in the PCI Express interface IC category. Its 196-PBGA package is intended for dense system-level implementations where the number of routing connections and the need for high-speed differential signaling make a fine-pitch BGA assembly practical. PEX8609-BA50BI is associated with the Broadcom PEX 8609 product family and a flexible eight-lane, eight-port PCI Express architecture. The product overview describes the PEX 8609 as a PCIe switch with advanced capabilities. DMA support can reduce the involvement of the host processor in data movement when the surrounding system is designed around the device's transfer capabilities, although actual throughput depends on lane width, payload size, reference clocking, and peer-device behavior. Typical system roles include embedded computing platforms, storage systems, industrial controllers, test equipment, and networked edge systems that need several PCIe endpoints behind one host interface. The device is also relevant to add-in cards and embedded modules using a dense BGA footprint. These uses benefit from consolidating multiple downstream links into one switch rather than requiring separate root ports for every peripheral. Board design requires careful high-speed signal-integrity control, uninterrupted reference-clock distribution, solid power and ground planes, and BGA-package assembly capability. The 196-pin land pattern must be implemented exactly from the manufacturer's package drawing, including ball assignments, solder-mask details, and via geometry. Validate signal losses, connector and trace discontinuities, inter-pair skew, and power-plane return paths before production release. This product summary combines the documented PCIe architecture and package characteristics with practical design guidance for evaluating the PEX8609 in multi-endpoint systems. The page also distinguishes the exact catalog identifier from related spellings, clarifies where to obtain technical documents, and records practical sourcing and replacement questions that should be resolved before schematic and PCB sign-off.

RFQ צור קשר
PEX8612-BB50RBCF - 12-Lane PCIe 2.0 Switch | Broadcom
PEX8612-BB50RBCF

PEX8612-BB50RBCF - 12-Lane PCIe 2.0 Switch | Broadcom

Broadcom PEX8612-BB50RBCF is a 12-lane, 3-port PCI Express Gen 2 switching IC with integrated 5.0 GT/s SerDes, supplied in a 324-ball FCBGA package measuring 19 x 19 mm. The device supports a commercial temperature grade and is identified as a CMOS PCI bus controller with ball terminals and a square package. A PCI Express switch is a semiconductor device that routes high-speed serial lanes between a host or upstream endpoint and multiple downstream endpoints. Within the interface hierarchy, the PEX8612 belongs to the PCI Express switch-controller family, using lane switching to expand connectivity without adding a separate host bridge. This makes it useful where multiple PCIe devices must share a limited upstream link or where expansion and fabric-management functions are required. Key features include support for 12 PCIe lanes, three ports, PCIe Gen 2 operation, integrated 5.0 GT/s serializers and deserializers, and typical power dissipation of 1.5 W. The 324-ball FCBGA package supports compact, high-density server and embedded-system designs. Its I2C technology designation provides a management interface, while the lead-free construction and RoHS features align with modern environmental requirements. The PEX8612 architecture consolidates multiple PCIe links into a switching fabric and allows downstream devices to operate behind a common upstream connection. Integrated SerDes reduces the need for external transceiver circuitry, while the compact BGA footprint supports high-density routing on multilayer boards. Because the device has 324 terminals, PCB design must include careful ball assignment, power distribution, and high-speed signal-integrity work. Typical applications include server expansion, storage systems, embedded computing platforms, industrial controllers, and networked edge equipment. In each case, the switch provides a practical way to add PCIe endpoint connectivity while preserving the 5.0 GT/s PCIe Gen 2 signaling rate. The three-port arrangement is particularly relevant to systems connecting several NVMe, network, or accelerator devices behind a single host interface. Board layout is the main implementation constraint. High-speed differential pairs require controlled impedance, uninterrupted reference planes, minimal layer transitions, and careful separation from clock and switching-node energy. Thermal design must also accommodate the typical 1.5 W device dissipation while maintaining adequate spreader and via access beneath the BGA. This page consolidates the confirmed lane, port, signaling, package, power, and environmental characteristics into an engineering-oriented view of the PEX8612-BB50RBCF. It also distinguishes the available ordering variants and explains the practical checks required before treating one as a replacement for another.

RFQ צור קשר
PEX8613-BA50BC - PCIe 2.0 12-Lane 3-Port Switch | Broadcom
PEX8613-BA50BC

PEX8613-BA50BC - PCIe 2.0 12-Lane 3-Port Switch | Broadcom

Broadcom PEX8613-BA50BC is a PCI Express switch IC with 12 PCIe Gen 2 lanes, a 5.0 GT/s data rate, and three switch ports in a 324-ball PBGA package measuring 19 x 19 mm. It is designed for systems that need to fan out a PCIe host connection among multiple downstream endpoints while preserving backward compatibility with PCIe Gen 1 devices. A PCI Express switch is a specialized interface semiconductor that belongs to the PCIe fabric-switch and interface-IC hierarchy. It manages transaction routing between a root port, an upstream endpoint, and downstream endpoints using configurable lanes and ports. The PEX8613 supports PCI Express Base Specification 2.0 compliance, automatic lane negotiation, lane reversal, and polarity reversal, allowing it to interoperate with systems containing different PCIe generation capabilities. The primary architecture provides a 12-lane, three-port PCIe Gen 2 configuration operating at up to 5.0 GT/s per lane. Backward compatibility with PCI Express Base Specification 1.1 and 1.0a allows a Gen 2 native chipset to fan out to endpoints that operate at Gen 1 rates. Lane reversal and polarity reversal support simplify integration where board routing constraints prevent conventional lane order or transmit/receive polarity from matching directly. The device is intended for PCI Express Base Specification 2.0 systems and was designed for Microsoft Vista compliance. Its switch function consolidates multiple downstream links behind a shared upstream connection, reducing the need for separate host-to-endpoint routing paths. Detailed lane allocation, reference-clock requirements, power sequencing, and register behavior should be confirmed against the PEX 8613 Product Brief when laying out the system. Typical uses include multi-endpoint embedded systems, industrial controller platforms, test and measurement equipment, storage systems, and compact computing products that require a PCIe switch rather than a simple root port. A system integrator can place the switch between a root complex and several endpoint devices, provided the selected downstream devices are supported by the port and lane organization of the PEX8613. PCB implementation requires careful high-speed signal routing and a 324-ball PBGA land pattern. Differential PCIe pairs should follow the reference-design connectivity and impedance requirements, while power, ground, and decoupling connections should be implemented with the shortest practical return paths. The PCB footprint and ball assignment must be checked against the package drawing before symbol and layout release. This product record combines the documented PCIe generation, lane count, port count, data rate, backward-compatibility features, package format, and sourcing details with practical implementation guidance. It also distinguishes exact-ordering-code alternatives from broader PCIe switches that require pinout, firmware, or board-level verification before replacement.

RFQ צור קשר
PEX8613-BA50BI - 12-Lane PCIe Gen 2 Switch | Broadcom
PEX8613-BA50BI

PEX8613-BA50BI - 12-Lane PCIe Gen 2 Switch | Broadcom

Broadcom PEX8613-BA50BI is a PCI Express Gen 2 switch IC with 12 lanes, 3 ports, and a maximum link rate of 5.0 GT/s. The device is intended for systems that require multiple PCI Express links to be switched between a host or endpoint and downstream devices. It supports the PCI Express Base Specification r2.0 and is backward compatible with r1.1 and r1.0a, providing a practical migration path for systems built around earlier-generation PCI Express designs. A PCI Express switch is a semiconductor in the interface-IC and semiconductor hierarchy that routes high-speed serial transactions among a root complex, endpoint devices, and expansion adapters. Unlike a simple connector or protocol translator, the PEX8613 integrates lane management, configuration handling, buffering, and traffic steering so that multiple PCI Express links can share a system interconnect. Its three-port architecture allows designers to construct fanout arrangements for storage, networking, graphics, or accelerator cards. Key features include support for auto-negotiation, lane reversal, and polarity reversal. Auto-negotiation permits the switch and connected devices to establish the highest mutually supported link rate and width. Lane reversal supports boards whose routing differs from the conventional lane order, while polarity reversal assists compatibility with interconnect implementations that invert the receiver and transmitter signals. These features can simplify board-level integration and improve tolerance of routing or cable-related signal variations. The manufacturer product brief identifies the PEX 8613 as a fully compliant PCI Express Base Specification r2.0 device and states that it is backward compatible with r1.1 and r1.0a. It was also designed for Microsoft Vista compliance, an important historical system requirement at the time of introduction. These compatibility features broaden its usefulness in legacy industrial, communications, and embedded platforms that need centralized PCI Express switching rather than a modern host-bridged topology. Typical applications include PCI Express expansion systems, multi-device embedded controllers, storage and networking adapters, industrial equipment with multiple high-speed peripherals, and compact backplane systems. The 12-lane, 3-port arrangement is useful when a system must balance bandwidth across several links while preserving backward compatibility with older endpoint hardware. The industrial-temperature ordering also makes the device relevant to equipment where ambient temperature requirements exceed ordinary commercial operating limits. Designers should use the manufacturer pin-description and reference-material sections when assigning the 324-pin ball-grid-array connections and PCB footprint details. Preserve the documented lane and reference-clock assignments, provide the required power rails with appropriate decoupling, and validate signal-integrity, thermal, and PCIe compliance behavior at the intended link rate before production release. This page organizes the PEX8613-BA50BI specifications, sourcing questions, compatibility details, application guidance, and the confirmed PEX8613-BA50BCG same-family alternative. It also distinguishes documented capabilities from parameters that must be confirmed in the complete manufacturer datasheet before schematic release or production qualification.

RFQ צור קשר
PEX8614-BA50BC - 12-Port Gen 2 PCIe Switch | Broadcom
PEX8614-BA50BC

PEX8614-BA50BC - 12-Port Gen 2 PCIe Switch | Broadcom

Broadcom PEX8614-BA50BC is a PCI Express switch IC with 12 lanes, 12 ports, and PCIe Gen 2 operation, housed in a 324-contact HSBGA package measuring 19 mm by 19 mm. It is designed to fan out multiple PCIe links through a non-blocking internal switch architecture and supports full line-rate packet transfer. Broadcom documents a maximum packet cut-through latency of 140 ns in an x4-to-x1 configuration, making the device suitable for latency-sensitive communication, server, and storage systems. A PCIe switch belongs to the PCI Interface IC category within interface semiconductors. Its function is to connect a host or upstream PCIe device to multiple downstream endpoints while arbitrating transactions, maintaining protocol ordering, and providing a shared switching fabric. The PEX8614 family supports lane configurations that allow system designers to balance port count, bandwidth, packaging, and board-routing requirements across complex PCIe topologies. Key characteristics include 12 PCIe lanes, 12 switch ports, PCIe Gen 2 operation, a 324-ball HSBGA package, and a 19 mm by 19 mm package footprint. The device also provides a non-blocking internal architecture and supports packet cut-through. These features make it applicable where several PCIe links need consolidation behind a common switching point rather than direct host-to-endpoint routing. The PEX8614 architecture uses packet cut-through to minimize the time packets remain inside the switch. Broadcom specifies a maximum latency of 140 ns for the x4-to-x1 arrangement and combines this behavior with large packet memory. The resulting architecture can sustain full line-rate operation across ports while supporting low-latency communication and server workloads that benefit from shorter transaction paths. Typical uses include PCIe expansion systems, external storage appliances, high-bandwidth network equipment, server accelerator platforms, and embedded systems that require more downstream PCIe endpoints than the root complex supports. The 12-lane, 12-port organization is particularly useful when a backplane or system controller must route multiple device links while preserving deterministic packet delivery. Board design requires careful high-speed signal-integrity work, including controlled impedance routing, continuous reference planes, appropriate via transitions, and minimization of stubs. Power delivery, decoupling, and thermal management must also be designed around the dense 324-contact HSBGA package. Differential-pair routing and connector or package-transition losses should be evaluated as part of the complete PCIe channel budget. This product record combines the identified PCIe architecture, package, lane, port, latency, and ordering details with application guidance, engineering caveats, and a structured comparison framework. It is intended to help engineers confirm fit, plan routing and power delivery, and determine whether a replacement or redesign is necessary before committing a complex PCIe board to production.

RFQ צור קשר