מוצרים (42,000+)

XC7Z030-2FFG676E - Dual Cortex-A9 Zynq-7000 SoC | AMD
XC7Z030-2FFG676E

XC7Z030-2FFG676E - Dual Cortex-A9 Zynq-7000 SoC | AMD

AMD/Xilinx XC7Z030-2FFG676E is a programmable system-on-chip combining a dual-core Arm Cortex-A9 processor with a Kintex-7 FPGA fabric, 125K logic cells, and an 800 MHz processor clock in a 676-ball FCBGA package measuring 27 x 27 mm. The device also integrates CoreSight debugging and programmable logic for embedded control, signal processing, and hardware acceleration. A Zynq-7000 SoC belongs to the FPGA & CPLD category while also functioning as a heterogeneous microprocessor-plus-logic device. Its Arm processing subsystem executes operating systems, networking stacks, and control software, while the FPGA fabric implements parallel datapaths, custom interfaces, and real-time signal-processing functions. This combination creates a single-chip platform for systems that otherwise might require a separate processor and programmable logic device. The XC7Z030-2FFG676E provides two Arm Cortex-A9 MPCore processors, 125K Kintex-7 logic cells, and an 800 MHz operating clock. Its programmable architecture allows designers to partition workloads between software and hardware. CoreSight support provides integrated debug visibility, while the broad fabric can accelerate functions such as video processing, packet handling, sensor fusion, control loops, and custom peripheral bridging without requiring a discrete FPGA. The FFG676 package provides 676 ball-grid contacts on a 27 x 27 mm square substrate and supports the compact board density required by industrial, communications, aerospace, and embedded-compute systems. Device-specific electrical characteristics, power rails, memory interfaces, and configuration limits must be implemented according to the AMD Zynq-7000 data sheet. Because the FCBGA package contains many power, ground, high-speed, and configuration balls, PCB escape routing, layer transitions, and thermal management require careful implementation. Typical applications include industrial automation controllers, industrial Ethernet and network equipment, embedded vision systems, communications infrastructure, test and measurement platforms, and high-performance embedded Linux products. The Arm subsystem is appropriate for control-plane software, while FPGA resources can accelerate parallel data movement or implement deterministic hardware functions beside the processor. A sound design begins with the AMD package pinout file and the Zynq-7000 data sheet, then validates power sequencing, configuration interfaces, memory topology, clocking, and differential I/O against the selected board stack-up. Because this device combines software execution with high-speed programmable logic, thermal design, signal integrity, and embedded software bring-up should be planned together rather than treated as independent tasks. This product overview consolidates the exact device identity, package characteristics, processor and logic resources, alternative-part constraints, and practical implementation considerations needed for initial design selection. It also distinguishes verified catalog attributes from engineering details engineers must confirm in the family documentation and their specific reference design.

RFQ צור קשר
XC7Z030-2FFG676I - Dual Cortex-A9 Zynq SoC | AMD
XC7Z030-2FFG676I

XC7Z030-2FFG676I - Dual Cortex-A9 Zynq SoC | AMD

The AMD XC7Z030-2FFG676I is a Zynq-7000 programmable SoC integrating a dual-core Arm Cortex-A9 MPCore processing system with a Kintex-7 FPGA fabric, 125K logic cells, an 800 MHz processor frequency, and a 676-ball FCBGA package measuring 27 x 27 mm. This combination places general-purpose Linux-capable processing and programmable hardware acceleration in one device. A Zynq SoC is a heterogeneous system-on-chip that combines an Arm processing system, programmable logic, memory controllers, and fixed-function peripherals. The processing subsystem executes operating systems, control software, and network applications, while the FPGA fabric implements parallel datapaths, custom interfaces, signal processing, and hardware acceleration. This architecture offers more flexibility than a fixed ASIC while reducing the component count associated with separate processors and FPGAs. The XC7Z030 device provides 125K programmable logic cells and an 800 MHz dual-core Arm Cortex-A9 configuration. Its programmable fabric supports parallel data processing and custom peripheral functions, while the ARM subsystem handles sequential software tasks. CoreSight debug capabilities support development workflows that combine instruction-level tracing, hardware visibility, and programmable-logic debugging. The -2 speed designation and industrial-temperature suffix organize the device for design planning, although detailed operating limits must be checked in the AMD data sheet. The 676-FCBGA package provides 676 electrical contacts and exposes the SoC's high-performance interfaces. Because this is a complex mixed-signal and high-speed programmable package, PCB construction, power planning, decoupling, and ball-escape routing are critical. Designers should follow the AMD package pinout, design guidelines, and power-estimation guidance rather than treating the BGA as a generic land pattern. Differential clocks, high-speed memory interfaces, and MGT transceivers require especially careful return-path and reference-plane design. Typical uses include industrial control, industrial networking, machine vision, video processing, communications equipment, embedded Linux systems, and sensor-processing platforms. The dual-core processor is suitable for an operating system and real-time tasks, while FPGA logic can accelerate filtering, protocol handling, image pre-processing, or custom interfaces. External DDR memory, nonvolatile storage, clock sources, transceivers, and power regulators are normally required around the SoC. The primary design trade-off is integration against implementation effort. Consolidating processor and FPGA functions reduces board-level interconnects and can simplify system partitioning, but firmware, HDL, interconnect constraints, and BGA layout must be planned together. Verify power sequencing, decoupling, memory topology, and transceiver requirements early because corrections are substantially harder after routing. This page combines the exact device identity, package characteristics, engineering application guidance, comparison parameters, and verified drop-in candidates. It also identifies compatibility questions that require confirmation against the AMD data sheet and package-placement diagram before any redesign is approved.

RFQ צור קשר
XC7Z030-2SB485I - Zynq-7000 SoC FPGA 125K 800MHz | AMD
XC7Z030-2SB485I

XC7Z030-2SB485I - Zynq-7000 SoC FPGA 125K 800MHz | AMD

The AMD Xilinx XC7Z030-2SB485I is a Zynq-7000 system-on-chip FPGA integrating a dual-core ARM Cortex-A9 processor with 125K Kintex-7 logic cells in a 484-FCBGA package. The device operates with an indicated processor frequency of 800MHz and is identified as an industrial-temperature, speed-grade-2 SoC FPGA. It combines programmable logic, hard processor peripherals, CoreSight debug support, memory interfaces, and programmable I/O in one integrated device. The 484-FCBGA package measures 19 x 19 mm according to distributor listings. A Zynq-7000 SoC is a heterogeneous FPGA platform rather than a conventional microcontroller or standalone FPGA. Its ARM Cortex-A9 processing subsystem executes software, operating systems, control code, and network protocols, while the Kintex-7 FPGA fabric implements parallel data processing, custom interfaces, accelerators, and timing-critical logic. This combination makes the device useful when a product needs more deterministic hardware assistance than a general-purpose processor can provide without adding a separate FPGA package. The XC7Z030-2SB485I provides 125K logic cells, an 800MHz listed device frequency, dual ARM Cortex-A9 MPCore processing, and CoreSight system-on-chip functionality in the 484-FCBGA (19 x 19 mm) package. These headline features position the part between smaller Zynq-7000 devices and larger Kintex-7 FPGA implementations. The integrated processor supports software-controlled workflows, while programmable logic can accelerate parallel tasks or provide custom peripheral connectivity. Its architecture is useful for industrial automation, machine vision, industrial networking, embedded control, communications gateways, and test equipment. In a machine-vision controller, for example, the programmable logic can acquire and pre-process image data while the ARM subsystem handles higher-level control. In a communications gateway, software can manage protocols and networking while dedicated fabric logic handles deterministic data movement or custom interfaces. Design decisions must account for the large BGA package, high pin count, multilayer PCB requirements, power integrity, thermal performance, and the complexity of programming both the FPGA fabric and processor subsystem. Because the verified data supplied for this part does not include complete power, I/O, memory-interface, temperature-range, pinout, or compliance tables, those values remain designated for datasheet confirmation. This page distinguishes confirmed distributor information from parameters requiring verification in AMD's official Zynq-7000 documentation. This page combines verified distributor availability, a same-footprint regional source-code comparison, practical application guidance, and design cautions that are not consolidated in a single distributor listing. It is intended to accelerate component selection while directing engineers to the authoritative AMD datasheet and package pinout resources before layout release.

RFQ צור קשר
XC7Z030-2SBG485E - 800MHz Zynq-7000 SoC | AMD/Xilinx
XC7Z030-2SBG485E

XC7Z030-2SBG485E - 800MHz Zynq-7000 SoC | AMD/Xilinx

AMD/Xilinx XC7Z030-2SBG485E is a Zynq-7000 programmable SoC combining a dual-core ARM Cortex-A9 MPCore processor at 800 MHz with a Kintex-7 FPGA fabric containing 125K logic cells in a 484-FCBGA package measuring 19 mm by 19 mm. The integrated system-on-chip architecture combines hard processor logic, programmable logic, CoreSight debug support, and programmable I/O in one device. A Zynq-7000 SoC is an adaptive SoC that combines an ARM microprocessor system with FPGA fabric. This hierarchy places the device between a general-purpose microprocessor and a conventional FPGA, allowing software-controlled functions and hardware-accelerated datapaths to share one package. Unlike a separate processor and FPGA, the integrated architecture can provide a lower-latency interface between software and programmable logic while reducing board-level component count. The XC7Z030-2SBG485E provides two ARM Cortex-A9 processor cores operating at 800 MHz, 125K FPGA logic cells, and 256 KB of on-chip memory according to the AMD product listing. Its speed-grade-2 suffix identifies the performance grade, while the extended-temperature suffix identifies its environmental grade. The device also includes CoreSight technology for processor and system debugging. These characteristics make it suitable for embedded control, industrial automation, communications equipment, instrumentation, and mixed software-and-logic systems. The Zynq architecture separates the hard processor system from the programmable FPGA resources. Software executes in the ARM processing environment, while designers can implement parallel datapaths, custom interfaces, accelerators, and control logic in the FPGA fabric. The integrated device is particularly useful when deterministic data movement, high-throughput parallel processing, or direct access between software and hardware is important. Designers should use AMD development tools and generated constraints to validate placement, routing, timing, and board-level connectivity. Typical designs include industrial gateways, factory automation controllers, test and measurement platforms, video-processing systems, embedded servers, and communication equipment. The dual Cortex-A9 configuration supports multitasking and control software, while the 125K logic cells allow custom hardware acceleration or interface consolidation. Compared with a processor-only design, the FPGA resources can execute parallel operations without depending on general-purpose software timing. PCB implementation requires careful attention to the 484-FCBGA layout, power rails, decoupling, clocking, and high-speed escape routing. Place input and output capacitors close to their associated device pins, use the manufacturer reference design as the baseline for stack-up and power planning, and inspect all XDC constraints for pin placement and timing. The 19 mm by 19 mm package also demands thermal via placement and adequate copper area for heat dissipation. This product page combines manufacturer and distributor technical facts with practical design guidance, package references, application analysis, and validated drop-in alternatives. It is intended to help engineers assess the XC7Z030-2SBG485E, compare it with same-package speed and temperature variants, and plan a robust Zynq-7000 PCB implementation.

RFQ צור קשר
XC7Z030-2SBG485I - Zynq-7000 SoC, 125K Logic Cells | AMD
XC7Z030-2SBG485I

XC7Z030-2SBG485I - Zynq-7000 SoC, 125K Logic Cells | AMD

The AMD XC7Z030-2SBG485I is a Zynq-7000 family System-on-Chip (SoC) that integrates a dual-core ARM Cortex-A9 MPCore processing system with a Kintex-7 class programmable logic fabric. This device combines the flexibility of an FPGA with the performance of an embedded processor, making it ideal for a wide range of applications including automotive, medical, and industrial systems. The device is housed in a 484-ball FCBGA package (19x19 mm) and operates at a maximum frequency of 800 MHz. A System-on-Chip (SoC) is an integrated circuit that consolidates all components of a computer or other electronic system into a single chip. The Zynq-7000 family specifically merges a hard ARM-based processing system (PS) with programmable logic (PL), allowing designers to implement custom hardware accelerators alongside software applications. This architecture enables high-performance, low-latency processing that is not achievable with traditional microprocessors or FPGAs alone. Key features of the XC7Z030-2SBG485I include 125,000 logic cells, dual ARM Cortex-A9 cores running at 800 MHz, and a 28nm process technology. The device supports a wide range of I/O standards and includes high-speed transceivers for serial communication. The 'I' suffix indicates an industrial temperature grade, with an operating range of -40°C to +100°C, making it suitable for harsh environments. From a technical perspective, the Zynq-7000 architecture provides a high-bandwidth interconnect between the PS and PL, enabling efficient data transfer. The device includes a memory management unit (MMU) for the ARM cores, as well as a rich set of peripherals including USB, Ethernet, and SPI. The programmable logic can be configured to implement custom peripherals, DSP blocks, or even soft-core processors, offering unparalleled design flexibility. Typical applications for the XC7Z030-2SBG485I include software-defined radio, motor control, image processing, and automotive driver assistance systems. The combination of a powerful processor and reconfigurable logic makes it an excellent choice for systems that require both high-level control and real-time signal processing. When designing with this device, careful attention must be paid to power supply decoupling and thermal management. The FCBGA package requires a well-designed PCB with adequate ground planes and thermal vias to ensure reliable operation at high temperatures.

RFQ צור קשר
XC7Z030-3FBG484E - 1GHz Dual-Core Zynq SoC | AMD
XC7Z030-3FBG484E

XC7Z030-3FBG484E - 1GHz Dual-Core Zynq SoC | AMD

The AMD XC7Z030-3FBG484E is a Zynq-7000 Kintex-7 system-on-chip combining a dual-core Arm Cortex-A9 MPCore processor with programmable Kintex-7 FPGA logic, 125K logic cells, and a 1 GHz processor clock in a 484-pin FCBGA package measuring 23 mm by 23 mm. The device also integrates CoreSight debug support, unified memory, and configurable programmable logic for processor-centric embedded systems. A Zynq-7000 SoC is a heterogeneous programmable semiconductor that combines an Arm processor subsystem with FPGA fabric in one device. The processor provides software execution, operating systems, networking stacks, and application control, while the programmable logic implements custom accelerators, interfaces, protocol logic, and time-critical datapaths. This integration places the SoC in the FPGA and SoC hierarchy while providing more flexibility than a fixed-function application processor. The XC7Z030 configuration provides 125K FPGA logic cells and a 1 GHz dual-core Arm Cortex-A9 processing subsystem. Its 484-FCBGA package supports high-density power, ground, and I/O connectivity in a 23 mm by 23 mm footprint. The product is identified for automotive applications, and a distributor listing also identifies the device as RoHS compliant. The published part code includes a speed-grade designation of -3 and an industrial -E temperature suffix. The integrated architecture allows hardware-assisted functions to execute in parallel with the Arm processors rather than forcing every operation through software. This can improve throughput for image processing, control loops, communications, data acquisition, and interface bridging. Processor-to-PL logic connectivity also reduces the need for external glue logic, although final performance depends on the design, memory interface, clocking, and software architecture. Typical implementations include industrial control, machine vision, networking equipment, test and measurement systems, embedded analytics, and automotive electronics. In a machine-vision controller, for example, the Cortex-A9 side can run control software while FPGA fabric accelerates deterministic acquisition or image-processing pipelines. In an industrial controller, programmable logic can implement fieldbus interfaces, data acquisition, and safety-adjacent timing functions alongside a Linux or real-time software stack. PCB implementation requires careful treatment of the 484-FCBGA package, including an escape-routing strategy, layer-stack planning, and dense via arrays beneath the device. The power architecture must supply the processor and programmable-logic rails with adequate transient response because processor activity can create fast current changes. Pin assignment, power sequencing, decoupling, and package-specific escape routing should be based on the official AMD Zynq-7000 documentation. This product record combines the exact manufacturer and distributor identity of the XC7Z030-3FBG484E with package, processor, logic-capacity, frequency, and application guidance. It also distinguishes documented same-footprint alternatives from broader Zynq devices whose packages differ, helping engineers make package-aware design decisions before committing to a PCB layout.

RFQ צור קשר
XC7Z030-3FBG676E - Dual Cortex-A9 Zynq SoC | AMD
XC7Z030-3FBG676E

XC7Z030-3FBG676E - Dual Cortex-A9 Zynq SoC | AMD

The AMD XC7Z030-3FBG676E is a Zynq-7000 Kintex-7 system-on-chip with two ARM Cortex-A9 MPCore processors, 125K logic cells, a 1 GHz processor operating frequency, CoreSight debug support, and a 676-ball FCBGA package measuring 27 x 27 mm. It combines programmable FPGA logic with a dual-core Arm processing system and integrated programmable logic on one device. A Zynq system-on-chip belongs to the FPGA and CPLD product hierarchy while also integrating a microprocessor subsystem and programmable peripheral logic. Unlike a discrete processor paired with a separate FPGA, the Zynq architecture allows hardware accelerators, interfaces, and control logic to be implemented in the programmable fabric while the Arm subsystem executes operating-system and application software. This combination is useful when designers need both software flexibility and deterministic hardware acceleration. Key features include the dual-core ARM Cortex-A9 MPCore subsystem, CoreSight debugging capability, 125K FPGA logic cells, and a 1 GHz advertised processor frequency. The integrated architecture can reduce inter-device communication requirements by placing processor-facing peripherals, custom interfaces, and accelerators close to the Arm cores. The 676-FCBGA package also supports the high pin count needed by a complex mixed processor-and-logic device. The XC7Z030 belongs to the Zynq-7000 product family and combines an Arm Cortex-A9 MPCore processing system with Kintex-7 FPGA logic. Its programmable resources can support parallel datapaths, protocol handling, video or image pipelines, signal processing, and custom accelerators. Developers can partition workloads between software running on the Arm processors and dedicated hardware implemented in the FPGA fabric, allowing hardware-specific tasks to execute concurrently. Typical applications include industrial control, networked communications, machine vision, video processing, embedded data acquisition, test equipment, and high-performance embedded systems. The device is particularly appropriate when deterministic data movement, parallel computation, or low-latency peripheral interfacing is required alongside a conventional operating environment and software development flow. PCB design requires careful attention to the 676-ball package, power delivery, decoupling, signal integrity, and thermal performance. Use the AMD package pinout files and Zynq-7000 SoC Technical Reference Manual when assigning ball assignments and planning board escape routing. Validate power sequencing, thermal conditions, high-speed memory interfaces, and differential I/O against the device-specific guidance before fabrication. This page combines the manufacturer data-sheet reference, current component listings, package details, speed-grade alternatives, and application-focused design guidance. It is structured to help engineers compare the exact XC7Z030-3FBG676E configuration, assess whether a closely related Zynq part can reuse an existing 676-ball design, and plan the hardware and software work required for a production embedded design.

RFQ צור קשר
XC7Z030-3FFG676E - Dual-Core Zynq-7000 SoC | AMD
XC7Z030-3FFG676E

XC7Z030-3FFG676E - Dual-Core Zynq-7000 SoC | AMD

The AMD/Xilinx XC7Z030-3FFG676E is a Zynq-7000 Kintex-7 system-on-chip that combines a dual-core Arm Cortex-A9 MPCore processor with CoreSight debug technology and Kintex-7 FPGA fabric. The device provides 125K logic cells, a maximum processor clock of 1 GHz, and a 676-ball FCBGA package measuring 27 x 27 mm. Its integrated architecture places a programmable processor system and FPGA fabric in one package, allowing hardware acceleration, parallel processing, and flexible peripheral interfacing in a single device. A Zynq-7000 SoC belongs to the FPGA & CPLD product hierarchy and combines an Arm application processing unit with programmable logic. The ARM Cortex-A9 cores execute operating-system-level software, networking stacks, and control code, while the Kintex-7 fabric implements hardware accelerators, custom interfaces, signal processing, and time-critical logic. This combination removes much of the complexity associated with separate processors and FPGAs while retaining software programmability and hardware-level parallelism. The XC7Z030-3FFG676E is identified as the -3 speed-grade device and operates with an extended-temperature designation. Its 125K logic-cell Kintex-7 fabric targets applications that need more programmable resources than small microcontroller-based logic devices while avoiding the cost and complexity of a large ASIC. The 1 GHz processor specification and CoreSight integration support a unified development flow spanning software, embedded Linux, real-time operating systems, and hardware debugging. Typical uses include industrial machine vision, network and telecom equipment, industrial Ethernet gateways, high-speed data acquisition, software-defined radio, embedded analytics, and test-and-measurement systems. The dual-core processor handles control planes and network services, while FPGA fabric can accelerate parallel algorithms or implement deterministic interfaces. Common applications also include radar, aerospace, and defense processing systems where programmable logic and real-time software must coexist. The 676-ball FCBGA package requires a dense multilayer PCB with controlled impedance routing, careful power-plane design, and thermal management appropriate for a large programmable SoC. Use the AMD package placement diagram and the Zynq-7000 device pinout files when assigning ball locations. Programming the device requires the corresponding Xilinx or AMD hardware toolchain and device support for the exact speed, package, and temperature identifiers. This page combines the verified device identity, package information, procurement references, and engineering guidance with family-level selection criteria and drop-in alternatives. It is intended to help engineers evaluate clocking, memory interfaces, I/O, thermal requirements, PCB complexity, and software compatibility before committing a 676-ball FCBGA design to production.

RFQ צור קשר
XC7Z030-3SBG485E - 1GHz Zynq-7000 SoC FPGA | AMD
XC7Z030-3SBG485E

XC7Z030-3SBG485E - 1GHz Zynq-7000 SoC FPGA | AMD

The AMD XC7Z030-3SBG485E is a Zynq-7000 all-programmable system-on-chip integrating a dual-core ARM Cortex-A9 MPCore processing system with Kintex-7 FPGA logic, CoreSight debug support, 125,000 logic cells, and a 1 GHz processor operating point in a 484-ball FCBGA package measuring 19 mm by 19 mm. It combines hard real-time processing-system resources with programmable logic for protocol bridging, hardware acceleration, image processing, control, and high-performance embedded applications. A Zynq-7000 SoC belongs to the FPGA and CPLD category while combining a processor-based subsystem with programmable logic. The processing system executes software through dual ARM Cortex-A9 cores, while the FPGA fabric implements parallel datapaths, custom interfaces, fixed-function accelerators, and timing-critical logic. This heterogeneous architecture can reduce external component count compared with separate processor and FPGA designs, although software, power, clocking, and thermal validation remain essential. Key features include 125,000 FPGA logic cells, a 1 GHz Cortex-A9 performance designation, dual-core ARM Cortex-A9 MPCore integration, CoreSight debug capability, and a compact 484-ball FCBGA package. The processor subsystem and programmable logic share access to memory and high-speed input/output resources, allowing designs to partition functions between sequential software and parallel hardware according to workload, latency, power, and real-time requirements. The -3 designator identifies the 1 GHz speed grade, while SBG485 identifies the 484-ball FCBGA configuration and E identifies the specified device grade. The 19 mm by 19 mm package has a 0.8 mm ball pitch and requires a dense, multilayer PCB with careful power delivery, decoupling, ball-by-ball escape routing, and thermal design. Designers should use the AMD package pinout files and Zynq-7000 technical documentation when assigning every power, ground, clock, configuration, processor, and programmable-logic ball. Typical applications include industrial control, robotics, machine vision, network equipment, sensor processing, test and measurement, communications infrastructure, and embedded systems that benefit from combining Linux or real-time software with FPGA acceleration. The dual-core processor handles control-plane software, operating systems, communications, and configuration tasks, while programmable logic can implement high-throughput data paths, custom serial interfaces, video pipelines, or hardware accelerators. A primary design consideration is power-domain sequencing. The processing system, programmable logic, memory interfaces, transceivers, and I/O supplies have distinct requirements, so rails should be enabled in the manufacturer-recommended order. Decoupling, independent voltage rails, clocking, JTAG, device configuration, and thermal management should be implemented according to the AMD Zynq-7000 design guidance before the PCB is released. This page combines the exact XC7Z030-3SBG485E identity, package information, documented alternatives, application guidance, and engineering-focused design notes. It also distinguishes verified same-package options from variants that use different packages, helping engineers avoid treating merely similar Zynq devices as true drop-in replacements.

RFQ צור קשר
XC7Z035-1FBG676C Dual-Core Zynq SoC | AMD/Xilinx
XC7Z035-1FBG676C

XC7Z035-1FBG676C Dual-Core Zynq SoC | AMD/Xilinx

AMD/Xilinx XC7Z035-1FBG676C is a programmable system-on-chip combining a dual-core ARM Cortex-A9 MPCore processing system with CoreSight debug support and a Kintex-7 FPGA fabric. The device provides 275K logic cells, operates at 667 MHz, and is packaged in a 676-pin FCBGA measuring 27 x 27 mm. Its integrated architecture combines hardware programmable logic with a general-purpose processor subsystem. A Zynq-7000 SoC is a heterogeneous programmable platform that integrates an ARM Cortex-A9-based processing system and Xilinx FPGA fabric on one semiconductor device. Within the product hierarchy, it is a system-on-chip, embedded processor FPGA, programmable logic device, and semiconductor. This integration can reduce the number of discrete components required when a design needs both application processing and flexible hardware acceleration. The XC7Z035 portion provides 275K logic cells for programmable interfaces, control logic, signal processing, and accelerator datapaths. Its dual-core ARM Cortex-A9 MPCore subsystem operates at 667 MHz and includes CoreSight debug capabilities. The 676-FCBGA package supports high-density pinout requirements for the Zynq-7000 family and is associated with a 27 x 27 mm body size in the product documentation. AMD documents the XC7Z035 in the Zynq-7000 SoC data sheet covering the XC7Z030, XC7Z035, and XC7Z045 families. A separate package placement document addresses XC7Z35-FBG676 and FFG676 devices, while the official package-pinout resource provides package files for design verification. These documents are important because processor performance alone does not establish PCB compatibility; speed grade, package marking, temperature designation, and ball assignments must also be checked. Typical uses include industrial control, machine vision, communications infrastructure, networked equipment, test and measurement systems, and embedded applications that combine Linux-capable processing with programmable hardware. The processor subsystem is suitable for operating systems, networking stacks, and control software, while the FPGA fabric can implement deterministic parallel datapaths, custom interfaces, or hardware-assisted acceleration. PCB design should preserve the 676-FCBGA land pattern, power and ground distribution, and decoupling arrangement defined by the AMD documentation. Because the device combines a processor system with programmable I/O, careful separation of sensitive clock, transceiver, and high-speed interface routing is essential. Configuration storage, startup sequencing, bank-voltage constraints, and the selected design tools must also be validated before production release. This page combines the verified device identity, package details, family documentation, pricing evidence, application guidance, and same-package migration options into an engineering-focused reference. It also highlights the verification steps needed when considering an FPGA or SoC replacement, where package compatibility alone does not guarantee identical software timing, power behavior, configuration, or lifecycle requirements.

RFQ צור קשר
XC7Z035-1FBG676I - 667MHz Zynq SoC FPGA | AMD
XC7Z035-1FBG676I

XC7Z035-1FBG676I - 667MHz Zynq SoC FPGA | AMD

The AMD XC7Z035-1FBG676I is a Zynq-7000 adaptive system-on-chip integrating a dual-core Arm Cortex-A9 MPCore processing system with CoreSight debug, a Kintex-7 FPGA fabric, 275,000 logic cells, and a 667 MHz processor clock in a 676-FCBGA package measuring 27 x 27 mm. Its operating temperature range is -40°C to +100°C, and the industrial suffix identifies a temperature-qualified assembly for demanding embedded and industrial systems. A Zynq-7000 SoC belongs to the FPGA & CPLD hierarchy and combines a hardware adaptive SoC architecture with programmable logic. Unlike a standalone microcontroller, the device allows ARM software and FPGA fabric to operate within one chip while communicating through dedicated interfaces. This heterogeneous architecture supports concurrent control processing, hardware data processing, signal acquisition, communications, and real-time decision-making without requiring separate processor and FPGA packages. The device provides approximately 275,000 logic cells and 250 I/O in its largest configuration. A 667 MHz Cortex-A9 processor supports the embedded software side, while the Kintex-7 fabric handles parallel logic, high-speed interface functions, protocol acceleration, and timing-sensitive workloads. CoreSight provides integrated visibility for debugging the processing system, and the Zynq architecture supports a combination of Linux, real-time operating systems, bare-metal firmware, and hardware-assisted pipelines. The XC7Z035-1FBG676I uses a 676-ball flip-chip BGA package, making it appropriate for dense multilayer PCB layouts with high-density escape routing and controlled impedance requirements. Its industrial temperature qualification covers applications operating from -40°C through +100°C. The package combines the Arm processing system, programmable logic, memory interfaces, and general-purpose I/O in a single 27 x 27 mm component. Typical uses include industrial machine vision, test and measurement equipment, industrial networking, embedded video processing, communications infrastructure, and control systems that benefit from parallel hardware acceleration. Designers can assign time-critical filtering, protocol conversion, data acquisition, or interface bridging to the programmable logic while the Arm cores execute control software, operating systems, communications stacks, and supervisory functions. PCB implementation requires careful BGA escape routing, power and ground-plane design, decoupling, thermal management, and differential-pair routing. Use the AMD Zynq-7000 package pinout files referenced in the design documentation to assign every ball correctly. Confirm the selected DDR memory interface, transceivers, bank voltages, configuration method, and clocking requirements before schematic capture. This page combines the confirmed device identity, package, operating-temperature, lifecycle, and environmental information with practical implementation guidance. It also identifies same-footprint Zynq-7000 ordering options for engineering comparison while distinguishing speed, temperature, and extended-temperature qualification changes that must be checked before substitution.

RFQ צור קשר
XC7Z035-1FFG676C - 667MHz Dual Cortex-A9 SoC FPGA | AMD
XC7Z035-1FFG676C

XC7Z035-1FFG676C - 667MHz Dual Cortex-A9 SoC FPGA | AMD

The AMD XC7Z035-1FFG676C is a Zynq-7000 Kintex-7 system-on-chip combining a dual-core Arm Cortex-A9 processor with 275K logic cells of FPGA fabric in a 676-ball FCBGA package measuring 27 x 27 mm. The integrated processor subsystem operates at 667 MHz, while the programmable logic section supplies parallel hardware acceleration, flexible interfaces, and dedicated processing resources within one device. A Zynq-7000 SoC belongs to the system-on-chip family, combining a hard microcontroller subsystem with programmable FPGA logic. This integration removes the need to place a separate processor and FPGA on the same board, while preserving software programmability through the Arm Cortex-A9 platform and hardware customization through Kintex-7 FPGA resources. The resulting architecture can accelerate data movement, filtering, encryption, image processing, and interface conversion without relying exclusively on sequential software execution. Key characteristics of the XC7Z035 include two Cortex-A9 processor cores, 667 MHz clocking, 275K logic cells, and support for CoreSight-based debug and trace visibility. The -1 device designation identifies the associated speed grade within the Zynq-7000 ordering system. The FFG676 designation identifies the 676-ball FCBGA package used by this ordering variant, with a stated package size of 27 x 27 mm. The programmable architecture makes this device suitable for industrial control, machine vision, network appliances, test equipment, communications infrastructure, and embedded edge systems. Designers can allocate deterministic tasks to FPGA logic while the operating system executes higher-level control, networking, or user-interface functions on the processor subsystem. Peripheral interfaces can therefore be implemented with predictable timing rather than depending entirely on interrupt-driven software servicing. Board design requires careful allocation of power, ground, high-speed transceiver, clocking, and processor debug resources. Use the AMD package-placement diagrams and Zynq-7000 data sheet to assign every ball before routing PCB traces. The 676-ball package also demands a fine-pitch PCB layout with controlled impedance and appropriate power-delivery networks. Selection should begin with the required processor software image, FPGA utilization, transceiver count, peripheral mix, operating temperature, and lifecycle expectations. Confirm that the chosen ordering variant satisfies all mechanical, electrical, and software requirements before committing the footprint. This page combines verified ordering details, package information, practical design guidance, and a structured comparison of same-family alternatives.

RFQ צור קשר
XC7Z035-1FFG676I - 275K Logic Cell Zynq SoC | AMD
XC7Z035-1FFG676I

XC7Z035-1FFG676I - 275K Logic Cell Zynq SoC | AMD

The AMD XC7Z035-1FFG676I is a Zynq-7000 Kintex-7 system-on-chip combining a dual-core Arm Cortex-A9 processor with 275,000 FPGA logic cells in a 676-ball FCBGA package measuring 27 x 27 mm. The processor operates at 667 MHz, while the programmable logic fabric supports hardware acceleration, parallel processing, custom interfaces, and high-speed signal processing. The device is positioned for industrial, networking, video, communications, and embedded control systems requiring an integrated ARM processor and FPGA architecture. A system-on-chip integrates programmable logic and a processing system within one device. In the Zynq-7000 hierarchy, this component is a Zynq SoC combining an Arm Cortex-A9 application-processing subsystem with a Kintex-7 FPGA fabric. This integration reduces the number of discrete components needed for a control-plane processor and programmable accelerator, while retaining the flexibility of hardware data paths and software-controlled management. The XC7Z035-1FFG676I provides 275K logic cells, a dual-core Arm Cortex-A9 MPCore configuration, CoreSight debug capability, and a maximum listed processor frequency of 667 MHz. Integrated security and management features include AES encryption support, watchdog timeout detection, and an integrated temperature sensor. The industrial-temperature suffix identifies the -40°C to +100°C operating range for demanding embedded and industrial equipment. The architecture separates software-intensive control functions from time-critical datapaths. ARM software can manage communication stacks, control sequencing, and application logic, while FPGA fabric can accelerate image processing, protocol conversion, data filtering, or fixed-function parallel pipelines. The 676-ball FCBGA package supports dense interconnect to external memory and high-speed peripherals, but its ball pitch, power delivery, and thermal requirements make careful PCB planning essential. Typical uses include industrial machine vision, video capture and processing, industrial networking, secure embedded gateways, communications infrastructure, and high-performance embedded control. In these applications, the dual Cortex-A9 cores handle control software while Kintex-7 logic accelerates parallel data acquisition or media processing. The integrated watchdog and AES support are useful for resilient industrial and security-sensitive systems. The primary PCB considerations are power-rail sequencing, multilayer decoupling, controlled-impedance routing, thermal management, and BGA assembly yield. Validate the complete power-up and power-down sequence, maintain continuous return paths beneath high-speed routes, and provide adequate copper and cooling for the device's industrial-temperature operation. This product page combines the verified device identity, package information, temperature range, security functions, comparison guidance, and engineering-oriented selection notes to help engineers evaluate the XC7Z035-1FFG676I for embedded FPGA-assisted processing designs.

RFQ צור קשר
XC7Z035-1FFG900C - 275K Logic Cell Zynq SoC | AMD
XC7Z035-1FFG900C

XC7Z035-1FFG900C - 275K Logic Cell Zynq SoC | AMD

The AMD XC7Z035-1FFG900C is a Zynq-7000 programmable SoC integrating a dual-core Arm Cortex-A9 MPCore processing system with a Kintex-7 FPGA fabric, 275K logic cells, and a 667 MHz processor operating frequency in a 900-FCBGA package measuring 31 mm by 31 mm. The device combines hard-processor peripherals, programmable logic, high-speed memory interfaces, and extensive general-purpose I/O within one heterogeneous system-on-chip. A Zynq SoC is a programmable system-on-chip that combines a hardwired Arm Cortex-A9 processing system with an FPGA fabric in the same package. This product hierarchy—Zynq SoC, FPGA and CPLD, programmable logic, integrated circuit, and semiconductor—places the XC7Z035 at the intersection of embedded software execution and hardware-accelerated logic. The integrated architecture can reduce interconnects between the processor and programmable logic compared with a separate processor and FPGA design. Key device characteristics include dual Arm Cortex-A9 MPCore cores, 275K FPGA logic cells, a 667 MHz operating frequency, a 900-FCBGA package, and 362 I/O according to the product listing data. The processing system includes on-chip memory and interfaces for external memory, while the Kintex-7 fabric supports hardware data processing, control logic, interface bridging, and accelerator functions. The Zynq-7000 architecture supports software control through the Arm Cortex-A9 subsystem and programmable hardware through the FPGA fabric. The 31 mm by 31 mm FCBGA-900 construction provides a large ball array for high-density connectivity. Design implementation must account for the fine package pitch, multilayer PCB requirements, high-speed routing rules, power and ground distribution, and thermal performance. Because the device combines thousands of programmable logic elements with a complex processor subsystem, bitstream generation, embedded software configuration, memory-interface design, and signal-integrity verification form one integrated engineering workflow. Typical applications include industrial automation, networked control systems, embedded vision, communications equipment, data acquisition, and high-performance embedded processing with FPGA-assisted acceleration. The programmable logic can implement parallel data paths, protocol interfaces, preprocessing pipelines, or custom accelerators while the Arm subsystem executes operating-system-level software, control logic, and network services. A critical implementation requirement is to follow the AMD package pinout and PCB guidelines for the FFG900 package. Use the official package pinout files and Zynq-7000 documentation to assign power, ground, configuration, memory, high-speed transceiver, and I/O balls. Validate multilayer stack-up, ball escape routing, decoupling, clocking, and thermal design before fabrication. This product page organizes the exact XC7Z035-1FFG900C identity, verified package and logic specifications, same-family replacement options, pricing status, and application guidance. It also emphasizes the engineering checks required when replacing a commercial-temperature FCBGA-900 Zynq device without changing the PCB footprint.

RFQ צור קשר
XC7Z035-1FFG900I - 275K Logic Cell Zynq-7000 SoC | AMD
XC7Z035-1FFG900I

XC7Z035-1FFG900I - 275K Logic Cell Zynq-7000 SoC | AMD

The AMD XC7Z035-1FFG900I is a Zynq-7000 adaptive SoC integrating a dual-core ARM Cortex-A9 processor with a Kintex-7 FPGA in a 900-FCBGA package. The device provides 275,000 logic cells, a 667 MHz Cortex-A9 processor, 18,022 Kb of block RAM, and 900 DSP slices in a 31 x 31 mm industrial-grade package. A Zynq adaptive SoC combines a programmable logic subsystem with a hard processor subsystem on one silicon device. In the broader semiconductor hierarchy, it belongs to the SoC category, combining a microprocessor, FPGA fabric, memory controllers, programmable I/O, and dedicated processing resources. This integration allows control logic, application processing, video acceleration, and signal processing to operate within one device and package. The principal features of the XC7Z035-1FFG900I include two ARM Cortex-A9 cores, CoreSight debug support, 275,000 FPGA logic cells, 18,022 Kb of block RAM, and 900 DSP slices. The 900-FCBGA package offers a large, fine-pitch interconnect for demanding designs requiring extensive parallel processing, high-speed memory interfaces, or multiple programmable I/O resources. The device is manufactured on a 28 nm process and operates from a 1 V core supply. Its heterogeneous architecture places programmable fabric and dedicated DSP blocks beside the ARM processing system. Software developers can execute an operating system or bare-metal code on the Cortex-A9 subsystem while FPGA fabric implements accelerators, interfaces, protocol logic, and real-time datapaths. Typical uses include industrial machine vision, networked video processing, communications infrastructure, high-performance embedded control, software-defined radio, and edge-AI systems. The dual Cortex-A9 configuration supports concurrent application tasks, while 900 DSP slices accelerate filtering, transforms, and other mathematically intensive operations. The large FPGA fabric is particularly useful when a fixed-function processor or discrete FPGA combination would consume excessive board area. Design with the complete 900-ball package rather than assuming a simpler pin-compatible footprint. Ball assignment, power rails, high-speed routing, decoupling, and exposed-pad or thermal requirements must follow the AMD package documentation and reference design. The 1 speed grade and industrial temperature designation should be considered during timing closure, especially where processor-to-FPGA interfaces or memory interfaces operate at high data rates. This product page combines the verified device identity, package characteristics, programmable resources, and processor architecture with practical replacement, comparison, and design guidance. It distinguishes genuine package-compatible options from devices that use different Zynq package suffixes and therefore require a PCB-level redesign.

RFQ צור קשר
XC7Z035-2FBG676E - 275K Zynq SoC, 800MHz | AMD
XC7Z035-2FBG676E

XC7Z035-2FBG676E - 275K Zynq SoC, 800MHz | AMD

The AMD XC7Z035-2FBG676E is a Zynq-7000 Kintex-7 system-on-chip with a dual-core ARM Cortex-A9 MPCore processor, CoreSight debug support, 275K programmable logic cells, and an 800 MHz processor rating. It is packaged in a 676-ball FCBGA package measuring 27 x 27 mm and operates across the stated 0°C to +100°C range. A Zynq-7000 SoC is a heterogeneous programmable system-on-chip that combines a hard processor subsystem with FPGA fabric in one device. The ARM Cortex-A9 subsystem executes operating-system-level software, while the Kintex-7 programmable logic implements parallel data paths, custom accelerators, interfaces, and signal processing. This integration can reduce component count and avoid data transfers between a separate processor and FPGA. The XC7Z035 offers 275K logic cells and 800 MHz performance in the listed configuration. Integrated features include AES encryption support, a watchdog timeout detector, and an integrated temperature sensor. The processor subsystem includes on-chip memory, external memory interfaces, and a broad collection of peripheral connectivity interfaces, while CoreSight provides integrated debug and trace visibility for embedded development. Its 676-FCBGA package supports high-density interconnect through 250 I/O, making the device appropriate for industrial control, networking, communications, image processing, and embedded edge systems. The integration of ARM software execution with FPGA fabric allows designers to place time-critical functions in programmable logic while retaining operating-system support for networking, control, storage, and user-facing functions. The processor, fabric, memory interfaces, and peripherals share a single programmable platform. A typical design would run board-support software on the dual Cortex-A9 processors and implement time-critical interfaces or accelerators in the Kintex-7 fabric. DDR memory, flash storage, transceivers, clocking, and power rails remain external system dependencies. The 27 x 27 mm BGA package also requires careful PCB escape routing, power delivery, thermal planning, and assembly-process control. Engineers should verify all signal assignments against the AMD DS190 device documentation before layout because the complete 676-ball pin map is too large to reproduce safely without the manufacturer package diagrams. Differential pairs, supply rails, high-speed memory connections, and configuration pins require exact pin, voltage, and impedance assignments. Power sequencing and thermal performance should be validated for the final board and enclosure. This product page consolidates the verified device identity, package information, search-driven alternatives, parameter comparisons, and engineering guidance into a design-focused reference. It supports early part selection while directing readers to the manufacturer documentation for authoritative pin-level implementation details.

RFQ צור קשר
XC7Z035-2FBG676I Dual Cortex-A9 800MHz 676-FCBGA | AMD
XC7Z035-2FBG676I

XC7Z035-2FBG676I Dual Cortex-A9 800MHz 676-FCBGA | AMD

The AMD XC7Z035-2FBG676I is a Zynq-7000 system-on-chip combining a dual-core ARM Cortex-A9 MPCore processing system with a Kintex-7 FPGA fabric, rated at 800 MHz and offered in a 676-FCBGA package measuring 27 x 27 mm. It contains 275K logic cells and integrates programmable logic, processors, memory interfaces, and high-speed connectivity in one device. A Zynq-7000 All Programmable SoC is a heterogeneous system-on-chip that combines an FPGA with one or more ARM processors. The FPGA fabric supports parallel hardware processing, while the Cortex-A9 subsystem executes operating-system, networking, control, and application software. This integration reduces the component count and board area compared with separate FPGA and processor designs while retaining programmable hardware parallelism. Key features include two ARM Cortex-A9 MPCore processors, 275K FPGA logic cells, an 800 MHz processor rating, and a 676-ball FCBGA package. The integrated architecture is suitable for industrial control, machine vision, communications gateways, embedded computing, and test equipment. Hardware accelerators can execute repetitive filtering, protocol handling, image processing, or data movement concurrently with software tasks. The device combines programmable logic with a coherent processor-centric software environment. Peripheral connectivity, memory interfaces, and programmable logic can be tailored around a specific workload, reducing external component requirements and data-transfer overhead. The -2 performance grade and industrial-temperature suffix identify a grade intended for applications requiring stronger performance and extended operating conditions than the -1 grade. Typical implementations use the Cortex-A9 subsystem for networking, device management, and user applications, while FPGA logic accelerates video pipelines, sensor fusion, protocol conversion, or high-speed interfaces. The same SoC can support control-only designs, processor-led gateways, or mixed workloads where software and hardware tasks operate concurrently. PCB implementation requires careful attention to the large BGA escape-routing strategy, power and ground distribution, decoupling, and thermal management. The Zynq-7000 package-pinout resources, identified by AMD as supporting package files in TXT and CSV formats, should be used with the selected device speed and temperature grade during symbol creation and PCB validation. This product page combines the device architecture and ordering information with package-aware alternatives, comparison criteria, and application guidance. It is intended to help engineers determine whether the XC7Z035-2FBG676I fits a design before moving to detailed power, thermal, timing, and PCB implementation checks.

RFQ צור קשר
XC7Z035-2FFG676E - 275K Logic Cell Zynq SoC | AMD
XC7Z035-2FFG676E

XC7Z035-2FFG676E - 275K Logic Cell Zynq SoC | AMD

The AMD XC7Z035-2FFG676E is a Zynq-7000 Kintex-7 FPGA system-on-chip with 275K logic cells, a dual-core Arm Cortex-A9 processing system operating at 800 MHz, and CoreSight debug support, housed in a 676-pin FCBGA package measuring 27 x 27 mm. It combines programmable logic with an embedded processing system in one device. A Zynq system-on-chip is an FPGA and SoC architecture that combines a hardwired ARM processing system with programmable logic fabric. The processing system executes operating-system-level software and controls system tasks, while the programmable logic implements parallel hardware, custom interfaces, signal processing, or accelerator functions. This division allows software and hardware responsibilities to be partitioned efficiently within one silicon device. The XC7Z035 provides 275K logic cells and an 800 MHz dual-core Cortex-A9 configuration. Its Zynq-7000 platform integrates processing, programmable logic, memory interfaces, and programmable peripherals on one package. The device also includes CoreSight technology for debug and trace-related functions, making the SoC suitable for complex embedded control systems that benefit from deterministic hardware acceleration. The -2 portion of the ordering code identifies speed grade 2, while the E suffix identifies the extended-temperature variant. The FFG676 package provides 676 ball-grid-array contacts in a 27 x 27 mm footprint. This high-pin-count package supports extensive connectivity between the processing system, programmable logic, external memory, and board-level peripherals, but it also requires careful ball assignment, power planning, and multilayer PCB layout. Typical uses include industrial automation, embedded vision, communications equipment, test and measurement, and networked control systems. In these applications, the Cortex-A9 cores can run control software or an operating system while the Kintex-7 programmable logic accelerates data acquisition, signal processing, protocol handling, or other parallel workloads. The architecture is particularly useful when designers want a compact embedded system with fewer inter-chip interfaces than a separate processor and FPGA. The principal design consideration is the complexity of a 676-pin FCBGA package. Power, ground, decoupling, high-speed routing, thermal management, and manufacturing capability must be planned before schematic capture. Differential interfaces and processor-to-memory connections require exact reference-design stackups and routing guidance from the AMD Zynq-7000 documentation. This page combines the verified device identity, package information, ordering-code details, comparison data, and practical implementation guidance into a compact engineering reference for evaluating the XC7Z035-2FFG676E.

RFQ צור קשר
XC7Z035-2FFG676I - Zynq-7000 SoC, 275K LC, 800MHz | AMD
XC7Z035-2FFG676I

XC7Z035-2FFG676I - Zynq-7000 SoC, 275K LC, 800MHz | AMD

The AMD (Xilinx) XC7Z035-2FFG676I is a Zynq-7000 All Programmable System-on-Chip (SoC) combining a dual-core ARM Cortex-A9 MPCore processing system running at 800 MHz with a Kintex-7 class FPGA fabric of 275K logic cells, housed in a 676-ball FCBGA (27x27 mm) industrial-grade package. A Zynq-7000 SoC is a class of programmable system-on-chip devices that integrate a hardwired processor system (PS) with programmable logic (PL) on a single die. Unlike a standalone FPGA or a standalone microprocessor, a SoC FPGA allows software running on the ARM cores and hardware accelerators in the fabric to communicate over high-bandwidth on-chip AXI interconnect, making the device family a cornerstone of modern embedded processing and adaptive computing hierarchies. Key features of the XC7Z035 include the mid-range 275K logic cell fabric, a -2 speed grade, and industrial temperature screening (the I suffix, typically -40C to +100C junction), making it suitable for harsh-environment deployments. The hard processor system offloads control-plane software while the fabric absorbs data-plane acceleration, math, and custom I/O. Architecturally, the device pairs the ARM Cortex-A9 NEON/FPU-enabled cores with CoreSight debug, caches, on-chip memory, and a rich set of PS peripherals, bonded to Kintex-7-based programmable logic with DSP slices, block RAM, and high-speed serial transceivers. AXI ports bridge the two domains with low latency. Typical applications include industrial automation and motor control, aerospace and defense processing, software-defined radio, video and image processing pipelines, and network packet processing where a soft processor would be too slow and a discrete CPU+FPGA pair too costly. When designing with this device, plan power sequencing between VCCINT, VCCAUX, and PS rails, and select a Vivado device name matching the industrial speed-grade variant to avoid implementation errors. This page synthesizes distributor pricing, verified same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ צור קשר
XC7Z035-2FFG900E - Dual-Core Cortex-A9 Zynq SoC | AMD
XC7Z035-2FFG900E

XC7Z035-2FFG900E - Dual-Core Cortex-A9 Zynq SoC | AMD

The AMD XC7Z035-2FFG900E is a Zynq-7000 system-on-chip combining a dual-core Arm Cortex-A9 MPCore processor operating at 800 MHz with CoreSight debug capability and a Kintex-7 FPGA fabric containing 275,000 logic cells. The device is packaged in a 900-ball FCBGA measuring 31 x 31 mm and supports extensive connectivity including CAN bus, Ethernet, I2C, SPI, UART/USART, USB OTG, MMC/SD/SDIO, and EBI/EMI. A Zynq system-on-chip is a heterogeneous programmable device that combines a hard microcontroller or microprocessor subsystem with programmable FPGA logic in one package. The processor subsystem executes operating-system software, controls external memory and peripherals, and communicates with software-defined hardware through memory-mapped interfaces. The FPGA fabric implements parallel datapaths, interfaces, protocol engines, image processing, and other hardware functions that would otherwise require separate devices. The XC7Z035 provides 275K logic cells and an 800 MHz processor core, giving designers a useful balance between software flexibility and hardware throughput. Its integrated Cortex-A9 subsystem supports the Zynq-7000 programmable logic environment, while CoreSight provides debug and trace visibility. The broad peripheral set reduces the need for discrete interface controllers when the design uses standard communication protocols. The XC7Z035 belongs to the Kintex-7-based portion of the Zynq-7000 family. This device combines processor-centric control with FPGA-based acceleration in one 900-FCBGA package. The FFG900 package offers 362 I/O according to the product listing, enabling high-density board-level integration while requiring careful power, ball-grid, and thermal planning. Typical applications include industrial control, machine vision, industrial networking, camera and image-processing systems, communications infrastructure, and embedded data acquisition. In these systems, the Arm processor can manage control software and network stacks while FPGA logic accelerates filtering, protocol conversion, sensor capture, or other timing-sensitive operations. A new design must account for the FCBGA-900 footprint, multilayer-board requirements, high-speed memory routing, power sequencing, and heat removal. Designers should also confirm the required Vivado toolchain, board-support packages, processor configuration method, and peripheral assignments against their system architecture before schematic capture. This product page combines the verified XC7Z035-2FFG900E identity, package, processor, FPGA, and interface information with package-aware alternatives and implementation guidance. It also highlights the principal design distinction: FPGA resource size, processor speed, temperature grade, and qualification suffix must be reviewed together when determining whether a related device is a true drop-in replacement.

RFQ צור קשר
XC7Z035-2FFG900I - 275K Logic Cell Zynq SoC | AMD
XC7Z035-2FFG900I

XC7Z035-2FFG900I - 275K Logic Cell Zynq SoC | AMD

The AMD XC7Z035-2FFG900I is a Zynq-7000 Kintex-7 system-on-chip with 275,000 programmable logic cells, a dual-core ARM Cortex-A9 MPCore processor, and an 800 MHz processor speed. The device combines programmable logic, ARM-based application processing, CoreSight debug support, dedicated DSP resources, and integrated memory controllers in a 900-FCBGA package measuring 31 x 31 mm. Its -2 speed grade and industrial temperature designation support demanding embedded, communications, industrial-control, and signal-processing systems. A Zynq-7000 SoC is an all-programmable system-on-chip that integrates a processing system and FPGA fabric on one silicon device. The ARM Cortex-A9 processing system executes operating systems, applications, and control software, while the Kintex-7 programmable logic implements parallel data paths, hardware accelerators, protocol handling, and custom peripherals. This heterogeneous architecture replaces a separate processor-plus-FPGA design with one device that supports software-controlled hardware acceleration. The XC7Z035 provides 275K logic cells and 900 DSP slices, making it suitable for applications that combine sequential control with high-throughput parallel processing. It also includes 18,022 Kb of block RAM according to the product listing. The dual-core Cortex-A9 subsystem operates at up to 800 MHz, enabling Linux, real-time operating systems, networking stacks, and sophisticated control algorithms while the FPGA fabric handles latency-sensitive data acquisition and filtering. The programmable logic and processing system communicate through dedicated interfaces, allowing designers to partition a design between software and hardware. Parallel lookup tables, DSP pipelines, block RAM, and high-speed serial or parallel interfaces can accelerate operations that would burden the processor. This division of labor is particularly effective in image processing, industrial vision, communications infrastructure, control systems, and network equipment requiring deterministic data movement. Typical deployments include industrial Ethernet gateways, high-speed data acquisition, machine vision, test and measurement equipment, software-defined radio, embedded control, and communications infrastructure. The 900-ball package provides extensive I/O for high-pin-count board designs, but its size and ball pitch require a multilayer PCB, careful power delivery, and disciplined signal-integrity implementation. Design with the manufacturer pinout files and Zynq-7000 documentation before assigning the 900 package balls. Decoupling networks, high-speed differential routing, clocking, MGT connectivity, processor boot storage, DDR memory, and programming interfaces must follow the relevant AMD reference designs. The large BGA also requires thermal analysis based on actual power consumption and the intended ambient temperature. This page consolidates the device identity, documented resource counts, package information, same-package alternatives, comparison parameters, and practical PCB guidance. It also identifies commercial questions for the Request a Quote workflow and separates package-compatible options from devices that require a different footprint.

RFQ צור קשר
XC7Z035-3FBG676E - 275K Cell Zynq SoC | AMD | Industrial
XC7Z035-3FBG676E

XC7Z035-3FBG676E - 275K Cell Zynq SoC | AMD | Industrial

The AMD XC7Z035-3FBG676E is a Zynq-7000 Kintex-7 system-on-chip combining a dual-core Arm Cortex-A9 processor at 1 GHz with 275,000 FPGA logic cells in a 676-ball FCBGA package measuring 27 mm by 27 mm. It integrates programmable logic, ARM Cortex-A9 processing, memory controllers, and fixed-function peripherals into one high-performance mixed-signal SoC. A Zynq-7000 SoC is a heterogeneous programmable device in which an ARM microprocessor subsystem operates alongside FPGA fabric. This device family belongs to the broader FPGA and system-on-chip hierarchy, allowing hardware designers to implement parallel pipelines, custom interfaces, video processing, control logic, and software-driven control functions in a single package rather than combining a separate processor and FPGA. Key characteristics include 275,000 logic cells, dual ARM Cortex-A9 MPCore processors, CoreSight debug support, and a maximum processor frequency of 1 GHz. The 28 nm implementation supports both hard real-time processing and programmable-logic acceleration. Its 676-ball FCBGA package provides a dense interface for high-speed memory, networking, display, storage, and external data acquisition. The architecture is particularly useful when an application benefits from combining Linux-capable application processing with deterministic parallel hardware. Software can control the system and manage data movement, while FPGA logic can accelerate filtering, codecs, image processing, protocol handling, or custom interface tasks. Compared with a microcontroller alone, the integrated fabric removes much of the external glue logic normally required for high-throughput data paths. Typical uses include industrial machine vision, factory automation, networked video processing, test and measurement systems, communications infrastructure, and embedded control platforms. The dual-core processor can partition control software from monitoring or data-processing workloads, while programmable logic interfaces directly to sensors, converters, memories, and high-speed external peripherals. Board design requires careful attention to power rails, high-speed routing, thermal management, and BGA assembly. Use the AMD pinout, package, and power-guidance documentation to assign power, ground, configuration, and I/O balls. A 676-ball BGA also requires a multilayer PCB with controlled-impedance routing, via-in-pad or via-fanout strategies, and assembly processes capable of handling the package's ball pitch and thermal requirements.

RFQ צור קשר
XC7Z045-1FBG676C - Dual Cortex-A9 Zynq-7000 SoC | AMD
XC7Z045-1FBG676C

XC7Z045-1FBG676C - Dual Cortex-A9 Zynq-7000 SoC | AMD

The AMD XC7Z045-1FBG676C is a Zynq-7000 Kintex-7 FPGA system-on-chip with 350K logic cells, a dual-core Arm Cortex-A9 processor, CoreSight debug support, and a 667 MHz processor operating frequency. It is packaged in a 676-ball FCBGA measuring 27 x 27 mm. This combination integrates programmable logic with an embedded application processor and CoreSight in one device. A Zynq-7000 system-on-chip is a programmable SoC combining a hard processor subsystem with FPGA fabric. Within the product hierarchy, it sits below FPGA and SoC devices, above Arm Cortex-A9-based programmable logic platforms, and within the broader semiconductor and embedded-computing categories. The processor executes operating-system and application software while the FPGA fabric implements parallel data paths, custom interfaces, accelerators, and real-time logic. The XC7Z045 provides 350K logic cells and a 667 MHz dual-core Arm Cortex-A9 configuration. Its 676-FCBGA package provides 676 terminals, measures 27 x 27 mm, and has a maximum seated height of 2.54 mm. The Ball termination and square package shape are identified in the product listing, while the surface-mount construction supports compact embedded-system designs. The integration of programmable logic with two Arm Cortex-A9 cores allows designers to divide a design between software-controlled sequential processing and hardware-level parallel processing. CoreSight support provides integrated debug visibility for the SoC. Because the processor and programmable logic share one package, the device can reduce interconnects and support high-bandwidth implementations requiring both control logic and dedicated hardware acceleration. Typical uses include industrial image processing, networked industrial control, communications infrastructure, test and measurement equipment, embedded vision, and high-performance embedded computing. The FPGA fabric is appropriate for deterministic datapaths and custom peripherals, while the Cortex-A9 subsystem supports control software, networking stacks, and application-level processing. The same dual-core architecture can also accelerate AES processing and other repetitive workloads through dedicated logic. Design planning must include the 676-ball BGA escape-routing strategy, power delivery across the processor and FPGA domains, thermal management, DDR memory implementation, and configuration-boot requirements. A completed PCB should be reviewed for via-in-pad compatibility, ball-pitch clearance, solder mask and paste design, and power-plane current distribution before the first assembly cycle. This page combines the verified device identity, package information, searchable family alternatives, application guidance, and engineering-focused replacement criteria to support faster component selection and PCB planning for Zynq-7000 designs.

RFQ צור קשר
XC7Z045-1FBG676I - Zynq-7000 SoC, 350K Logic Cells | AMD
XC7Z045-1FBG676I

XC7Z045-1FBG676I - Zynq-7000 SoC, 350K Logic Cells | AMD

The AMD XC7Z045-1FBG676I is a Zynq-7000 family System-on-Chip (SoC) that integrates a dual-core ARM Cortex-A9 MPCore processor with a Kintex-7 FPGA fabric. It is housed in a 676-pin FCBGA package (27x27 mm) and operates at a maximum clock frequency of 667 MHz. The device provides 350K logic cells, making it suitable for high-performance embedded applications requiring both software programmability and hardware flexibility. A System-on-Chip (SoC) is an integrated circuit that combines multiple system components, such as processors, memory interfaces, and I/O, onto a single substrate. The Zynq-7000 family specifically merges a processing system (PS) based on ARM cores with programmable logic (PL) based on FPGA fabric. This architecture allows designers to implement complex algorithms in hardware while maintaining the flexibility of software-defined control, bridging the gap between traditional microprocessors and FPGAs. Key features of the XC7Z045-1FBG676I include 350K logic cells, 256 KB of on-chip RAM, and support for high-speed transceivers. The device also includes a rich set of I/O options, including multiple high-speed serial transceivers and general-purpose I/O banks. The dual-core ARM Cortex-A9 processor runs at up to 667 MHz, providing substantial processing power for real-time applications. From a technical perspective, the XC7Z045-1FBG676I leverages AMD's advanced 28nm process technology, balancing performance and power efficiency. The integration of the ARM processor with the Kintex-7 FPGA fabric enables low-latency, high-bandwidth communication between software and hardware, which is critical for applications like software-defined radio, image processing, and industrial control. The device supports a wide range of industry-standard interfaces, including DDR3/DDR4 memory controllers and PCIe. Typical applications include high-end embedded computing, aerospace and defense systems, medical imaging, and wired/wireless communications. The combination of a powerful processor and reconfigurable logic makes it ideal for prototyping and production in demanding environments. When designing with this device, careful attention must be paid to power supply sequencing and decoupling. The multiple power rails require proper sequencing to avoid latch-up or damage. Additionally, the high-speed transceivers demand clean power and careful PCB layout to maintain signal integrity.

RFQ צור קשר