מעגלי ממשק
תת-קטגוריות
מוצרים (2,200+)
ADM485JNZ - 5V 5Mbps RS-485/422 Transceiver | Analog Devices
Analog Devices ADM485JNZ is a 5 V low-power EIA RS-485 and RS-422 differential line transceiver with one driver and one receiver, a maximum data rate of 5 Mbps, and an 8-pin PDIP package. It is designed for balanced, high-speed, bidirectional data communication over multipoint bus transmission lines. The 5 V single-supply operating range of 4.75 V to 5.25 V supports conventional industrial and communications equipment. A differential line transceiver is an interface IC that combines a transmit driver and receive comparator for balanced communication links. Within the hierarchy of interface ICs, the ADM485JNZ belongs to the RS-485/RS-422 transceiver class and converts logic-level signals into noise-resistant differential bus signals. This category supports communication between distributed nodes over longer cables than ordinary single-ended logic interfaces. Key features include a 5 Mbps maximum data rate, low-power BiCMOS construction, fast switching behavior, a +12 V bus common-mode range, and protection against short-circuit and thermal overload. The device provides separate driver-enable and receiver-enable control, allowing the transmitter and receiver to be switched independently. These characteristics suit industrial control, instrumentation, factory automation, and other multidrop systems where reliable signaling and controlled bus contention are important. The ADM485 uses differential signaling to improve noise immunity and reduce electromagnetic-interference emissions relative to a single-ended interface. Minimal driver propagation delay permits high-speed transmission, while low skew helps reduce EMI interference between transitions. Because the verified product description identifies one transmitter and one receiver, systems requiring multiple bus nodes must add additional transceivers rather than treating the part as a multi-drop controller. Typical applications include RS-485 industrial networks, RS-422 point-to-point links, programmable logic controller and sensor interfaces, building-automation equipment, and factory data buses. In these systems, the ADM485JNZ can sit between a host UART or microcontroller and a twisted-pair bus. Termination, biasing, grounding, and protocol-level turnaround control remain important system-level considerations. When implementing the interface, verify the 4.75 V to 5.25 V supply requirement and design the bus network with appropriate termination at the physical endpoints. Avoid relying on the transceiver alone for surge, ground-offset, or isolated protection. The 8-pin PDIP package is also mechanically incompatible with the SOIC and MSOP versions of the ADM485 family, making package selection critical during replacement. This product analysis consolidates verified manufacturer information, distributor pricing, package details, lifecycle data, and pin-to-pin replacement guidance. It also distinguishes the available same-footprint alternatives from surface-mount and cross-package family variants so engineers can make a replacement decision without assuming electrical equivalence implies mechanical compatibility.
ADM485JRZ - 5V 5Mbps RS-485 Transceiver | Analog Devices
Analog Devices ADM485JRZ is a 5 V low-power half-duplex RS-485 and RS-422 transceiver with a maximum data rate of 5 Mbits/s, supplied in an 8-pin SOIC package. The device supports balanced differential data transmission over multipoint bus lines, with independently controlled driver and receiver sections for flexible half-duplex communication. An RS-485 transceiver is a physical-layer interface IC that converts logic-level signals into differential bus signals and receives differential bus signals back into logic-level outputs. In the product hierarchy, it is a differential line transceiver within interface ICs and a semiconductor. Its differential signaling improves common-mode noise immunity, while the RS-485 standard supports communication over shared multipoint cabling when correctly terminated and biased. The ADM485 family combines a 5 Mbit/s data rate with low-power operation and short propagation delays. These characteristics suit industrial communication links where low channel skew and rapid switching help reduce timing margins and electromagnetic-interference concerns. Its 8-pin SOIC package also provides a small surface-mount footprint for compact interface sections in control systems, instrumentation, and communications equipment. The architecture includes dedicated differential driver outputs and receiver inputs, and both functions can be enabled independently according to the cited component description. Independent control supports bus designs that need to listen without actively driving the line, as well as arrangements where transmit and receive timing is managed by external control logic. Exact propagation-delay, slew-rate, and power-consumption values are not supplied in the verified excerpts and should be taken from the manufacturer datasheet. Typical uses include industrial RS-485 buses, RS-422 point-to-point links, factory data acquisition, building-control networks, instrumentation, and data communications between embedded controllers and peripheral modules. For multipoint RS-485 networks, cable length, topology, termination, biasing, and common-mode limits must be evaluated together; the transceiver alone does not determine reliable maximum bus distance. The primary design consideration is verifying pin functions, supply sequencing, signal polarity, and transceiver-enable timing against the exact ADM485JRZ datasheet. Designers should also use the manufacturer-specified protection and bypass strategies, provide a clean 5 V supply, and validate termination and fail-safe behavior across cable lengths and system grounding conditions. This page consolidates the verified manufacturer and distributor information, compares potential SOIC-8 replacements, and adds application guidance and design checks that help engineers evaluate ADM485JRZ beyond a basic distributor specification table.
ADM488AN - 250kbps Full-Duplex RS-485 IC | Analog Devices
The Analog Devices ADM488AN is a 5V, low-power, full-duplex, slew-rate-limited EIA RS-485 transceiver rated for data rates up to 250kbps, supplied in an 8-pin PDIP package. It combines one differential driver and one differential receiver, supports ±12V bus common-mode range, and provides 12kΩ receiver input impedance. According to the manufacturer ADM488 data sheet, the device is intended for balanced data transmission and complies with EIA RS-485 and RS-422 interfaces. An RS-485 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over long, multipoint copper buses. The differential signal helps reject common-mode noise, while the receiver converts the differential bus voltage back into a logic-level output. The ADM488 belongs to the broader RS-485 transceiver, communications interface, interface IC, and semiconductor hierarchy. Key features include a maximum 250kbps data rate, a single 5V supply, low power operation, and slew-rate-limited outputs that reduce unwanted high-frequency EMI. The receiver's 12kΩ input impedance supports practical bus loading, while the ±12V common-mode range accommodates signaling variations in industrial environments. The device also meets the EIA RS-485 standard and includes 2kV EFT protection according to the cited manufacturer and datasheet listings. The ADM488 and ADM489 family is designed for balanced differential communication on multipoint bus transmission lines. Full-duplex operation supports separate transmit and receive paths, which is useful when a node must communicate while monitoring another channel. Slew-rate limiting helps control edge rates and reduce electromagnetic emissions, although cable length, termination, biasing, and grounding remain application-level requirements. Typical applications include industrial control networks, building automation, instrumentation, factory equipment, and isolated or non-isolated RS-485 data links. The 8-pin PDIP package is suitable through-hole assembly where a robust, inspectable package is preferred. The manufacturer lists the ADM488 as a production device, but exact stock, lead time, and price are not available in the supplied data. For a new design, verify the complete pinout, receiver enable or shutdown behavior, bus termination, fail-safe biasing, and isolation strategy against the exact datasheet revision before layout. Do not substitute a part solely by function; the alternative must use the same package footprint and be pin-to-pin compatible. This page combines manufacturer information, distributor availability, and verified cross-reference results into a practical sourcing and design reference.
ADM488AR - 250kbps Low-Power RS-485 Transceiver | Analog Devices
The Analog Devices ADM488AR is a 5 V, low-power, full-duplex, slew-rate-limited EIA RS-485/RS-422 differential line transceiver rated for data rates up to 250 kbps in an 8-lead SOIC package. It supports multipoint balanced data transmission while limiting bandwidth to reduce unwanted high-frequency harmonics and reflections. Key verified features include a ±12 V bus common-mode range, 12 kΩ input impedance, and 2 kV EFT protection. The device is intended for industrial, commercial, and instrumentation networks requiring robust differential communications. An RS-485 transceiver is an interface IC that combines a differential driver and receiver, converting logic-level signals into balanced bus signals and restoring weak or noisy bus logic levels at the receiving endpoint. In the component hierarchy, the ADM488AR is an RS-485 transceiver, an interface IC, a communications semiconductor, and a physical-layer device supporting EIA RS-485 and RS-422 networks. Full duplex provides separate transmit and receive paths, allowing a node to send and receive independently when its bus architecture supports that operation. The verified electrical features emphasize low power, controlled edges, and multipoint-bus robustness. A single 5 V supply with ±10% tolerance simplifies interface design, while 12 kΩ receiver loading permits more devices on a bus than lower-impedance receivers. The ±12 V common-mode range covers a substantial portion of industrial ground-offset conditions. Slew-rate limiting is particularly useful when slower, rounded edges reduce EMI and ringing, although cable length, topology, termination, and data rate remain system-level constraints. The ADM488AR family is specified for EIA RS-485 and RS-422 communication, as described by Analog Devices. The AR ordering code identifies the verified surface-mount package configuration, while the manufacturer product page identifies the family as a production product. Exact pin names, temperature range, supply-current limits, receiver thresholds, driver-output levels, package dimensions, and absolute maximum ratings were not available in the supplied excerpts and therefore must be confirmed from the manufacturer datasheet before layout or qualification. Typical uses include industrial automation links, building-control networks, instrumentation buses, factory equipment, remote sensor interfaces, and embedded data links. The 250 kbps ceiling favors moderate-speed control and monitoring rather than high-bandwidth Ethernet or very fast storage interfaces. In a full-duplex design, pair the driver and receiver with the bus transceiver's specified pins, route differential traces as a controlled impedance pair, and apply termination and biasing only where required by the network architecture. The principal design consideration is that slew-rate limiting is a system tradeoff rather than a universal solution. Rounded transitions can reduce high-frequency content, but overly slow edges consume signal rise-time budget and may prevent reliable operation at the maximum 250 kbps rate over long cables. PCB symmetry, connector return paths, grounding, cable type, node spacing, common-mode behavior, and protection placement must be validated together. This page combines verified Analog Devices family information, distributor evidence, sourcing status, interface-application guidance, and a strict drop-in comparison framework. It also distinguishes confirmed specifications from unavailable values, helping engineers identify which details require direct review of the official ADM488 datasheet and package drawings before release to production.
ADM489AR - 250kbps Full-Duplex RS-485/422 | Analog Devices
The Analog Devices ADM489AR is a low-power, full-duplex, slew-rate-limited differential line transceiver rated for 250 kbps data transmission and supplied in a 14-pin SOIC package. It supports the EIA RS-485 and RS-422 standards, operates from a single 5 V supply within a 4.5 V to 5.5 V range, and provides separate transmit and receive paths for full-duplex point-to-point links. Its 12 kΩ minimum input impedance and ±12 V bus common-mode range provide practical margin in industrial multipoint networks, while 2 kV EFT protection helps withstand electrically noisy environments. An RS-485 transceiver is a physical-layer interface IC that converts logic-level signals into balanced differential bus voltages and receives differential bus voltages back into CMOS-compatible logic. This device belongs to the interface-IC hierarchy, alongside RS-422 transceivers and other differential data-interface products, and sits between a digital controller and a wired communications bus. Full duplex allows the transmitter and receiver to operate simultaneously, which is useful when a node cannot wait for bus turnaround. Key features include a 250 kbps data rate, one driver and one receiver, 5 V single-supply operation, ±12 V common-mode handling, and controlled slew rate. The slew-rate limitation reduces high-frequency harmonics and reflected-signal problems by preventing excessively fast bus transitions. The 2 kV EFT protection rating is particularly relevant in industrial environments where cables may carry electrostatic-discharge transients. The ADM489AR integrates separate differential driver outputs and receiver inputs rather than using a single shared multipoint bus segment like a half-duplex transceiver. Its architecture therefore suits point-to-point full-duplex equipment, industrial controllers, and communications links where continuous send and receive capability is required. Exact pin identities, output-disable behavior, receiver enable logic, and detailed electrical limits should be confirmed against the manufacturer datasheet before layout or firmware release. Typical uses include industrial RS-485 links, RS-422 point-to-point interconnects, factory automation equipment, remote sensor interfaces, and embedded control systems. In a 5 V design, the transceiver can bridge a microcontroller UART and a balanced cable while maintaining compatibility with established differential-bus infrastructure. Compared with half-duplex RS-485 designs, the main system benefit is simultaneous transmission and reception without shared-driver contention. A key design consideration is that low data rate alone does not eliminate the need for correct bus termination, controlled impedance, common-mode grounding, and transient protection. The differential pair should be routed as a balanced pair, with connector and cable arrangements selected to minimize external noise pickup. Supply decoupling should be placed close to the device, and unused or disabled inputs must be handled according to the datasheet to avoid floating digital nodes. This product page consolidates verified manufacturer and distributor information, sourced pricing references, engineering application guidance, and honest replacement screening. It distinguishes confirmed facts from parameters that require the datasheet, helping engineers evaluate the ADM489AR for procurement and board-level design without treating merely similar RS-485 devices as verified drop-in replacements.
ADN4624BCPZ - Quad 2.5Gbps LVDS Isolator | Analog Devices
The ADN4624BCPZ is a quad-channel, signal-isolated, low-voltage differential signaling (LVDS) buffer from Analog Devices that operates at data rates up to 2.5 Gbps with very low jitter. It integrates Analog Devices' iCoupler technology, enhanced for high-speed operation, to provide drop-in galvanic isolation of LVDS signal chains. The device is available in a 32-lead WFQFN exposed pad package (LFCSP) and supports a wide supply range of 1.7 V to 1.9 V on both VDD1 and VDD2, with a typical supply of 1.8 V. It provides 5700 Vrms isolation voltage and a common-mode transient immunity (CMTI) of 40 kV/µs, making it suitable for industrial and medical applications where robust isolation is critical. A digital isolator is a device that transfers digital signals across an isolation barrier, typically using capacitive, inductive, or optical coupling, to protect sensitive circuitry from high voltages, ground loops, and noise. In the hierarchy of signal conditioning, a digital isolator sits between the digital signal source and the receiving logic, ensuring signal integrity and safety. The ADN4624BCPZ specifically isolates LVDS signals, which are differential, low-voltage, high-speed signals used in applications like data acquisition, industrial networking, and medical imaging. Key features of the ADN4624BCPZ include four isolated LVDS channels (4+0 configuration), a data rate of 2.5 Gbps per channel, and very low jitter, which is essential for high-speed serial links. The device also features a refresh mechanism that monitors input and output states to ensure they remain the same in the absence of data transitions, such as at power-on. The 1.8 V supplies for the LVDS and isolator circuits enable low power consumption while maintaining high-speed operation. Technically, the ADN4624BCPZ uses iCoupler technology, which employs chip-scale transformers to couple signals across the isolation barrier. This approach provides superior performance compared to optocouplers in terms of speed, power, and reliability. The device is designed to meet the stringent requirements of industrial automation, motor control, and medical equipment, where isolation and signal integrity are paramount. Typical applications include isolated LVDS interfaces in data acquisition systems, industrial fieldbus networks, and medical imaging equipment. The ADN4624BCPZ is also used in test and measurement instruments where high-speed data transfer with galvanic isolation is required. When designing with this device, ensure that the supply voltages are within the specified range and that proper decoupling capacitors are placed close to the VDD pins. The exposed pad should be soldered to the PCB ground plane for optimal thermal performance. Also, consider the CMTI rating when operating in environments with high voltage transients.
ADN4624BCPZ-RL7 - Quad LVDS Isolator 2.5Gbps | Analog Devices
The ADN4624BCPZ-RL7 is a quad-channel, signal-isolated, low-voltage differential signaling (LVDS) buffer from Analog Devices that operates at data rates up to 2.5 Gbps with very low jitter. It integrates Analog Devices' iCoupler technology, enhanced for high-speed operation to provide drop-in galvanic isolation of LVDS signal chains. The device is available in a 32-lead WFQFN exposed pad package (CSP) and provides 5.7 kV rms isolation voltage with a common-mode transient immunity (CMTI) of 40 kV/µs. A digital isolator is a component that provides galvanic isolation between two circuits while allowing digital signals to pass across the isolation barrier. In the hierarchy of isolation components, a digital isolator is a type of signal isolator, which falls under the broader category of isolation components used in power management and signal conditioning. The ADN4624 specifically isolates LVDS signals, which are differential, low-voltage, high-speed signals commonly used in high-speed data transmission. Key features include four isolated LVDS channels (4+0 configuration), support for 1.7 V to 1.9 V supply voltages on both sides (VDD1 and VDD2), and an operating temperature range of -40°C to +125°C. The device ensures very low jitter, making it suitable for high-speed serial links where signal integrity is critical. The 5.7 kV rms isolation rating provides robust protection against voltage transients and ground potential differences. Technically, the ADN4624 uses iCoupler technology, which employs chip-scale transformers to transmit data across the isolation barrier, offering advantages over optocouplers in terms of speed, power consumption, and reliability. The device supports AC coupling and/or level shifting to LVDS receivers and from LVDS drivers, simplifying interface design. The 32-lead WFQFN package with exposed pad aids in thermal management and is suitable for space-constrained applications. Typical applications include isolated high-speed data acquisition systems, industrial fieldbus interfaces, medical equipment requiring patient isolation, and communication backplanes. The device is ideal for systems where high-speed data must cross an isolation barrier without compromising signal integrity. When designing with the ADN4624, ensure proper PCB layout with adequate spacing for isolation, and place decoupling capacitors close to the VDD1 and VDD2 pins. The exposed pad should be connected to the appropriate ground plane for thermal performance.
ADP5585ACBZ-00-R7 - 10 I/O Keypad Controller | Analog Devices
The Analog Devices ADP5585ACBZ-00-R7 is a 10-I/O port expander with a built-in keypad matrix decoder, programmable logic, reset generator, and PWM generator, housed in a 16-WLCSP package measuring 1.59 mm by 1.59 mm. The device uses an I2C interface and is designed to increase the number of inputs and outputs available to a host processor or reduce host GPIO requirements in compact embedded systems. An I/O expander is an interface IC that adds configurable digital input and output pins to a processor through a serial bus. The ADP5585 extends this function with event-oriented keypad scanning, a 16-element FIFO for recording events, programmable logic, and PWM generation. Its 10 configurable I/Os can support keypad decoding and other peripheral functions in portable devices, remote controls, cameras, healthcare equipment, industrial instrumentation, and other compact control systems. The verified product data identifies the device as an 8-bit I/O expander with a 1 MHz I2C interface and an operating supply range from 1.65 V to 3.6 V. The 16-WLCSP package is intended for space-constrained PCB layouts, while the integrated keypad functionality helps designers reduce the number of discrete row and column connections required for matrix keypads. The device also provides reset-generation and programmable-logic functions that can simplify control-panel designs. The ADP5585 is especially useful when a system needs both general-purpose digital I/O and keypad event detection. Instead of assigning every keypad row and column directly to a microcontroller, the host processor can configure the ADP5585 through I2C and read keypad events from the device FIFO. This can reduce processor pin count and simplify firmware organization, although the exact implementation must follow the manufacturer's register and electrical guidance. ADP5585ACBZ-01-R7 and ADP5585ACPZ-01-R7 are mentioned in the manufacturer datasheet for configurations supporting a larger keypad matrix. The target ADP5585ACBZ-00-R7 should therefore be selected only after confirming the required matrix size, pinout, voltage range, and register behavior. The available verified data does not provide exact pricing, complete pin names, lifecycle status, or a complete pinout for this specific ordering code. This page combines the verified manufacturer and distributor information with application guidance, design cautions, and comparison placeholders where source data is unavailable. Review the manufacturer datasheet before finalizing PCB layout, firmware, voltage tolerances, or production sourcing.
ADP5585ACBZ-01-R7 - 10-I/O Keypad Port Expander | Analog Devices
Analog Devices ADP5585ACBZ-01-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and PWM generator. The device supports keypad matrices up to 6 × 5 and provides a 16-element FIFO for event recording. It is packaged in a 16-WLCSP measuring 1.59 mm × 1.59 mm. An I/O expander is an interface IC that increases the number of digital input and output pins available to a host processor. A typical I2C or SPI expander connects through a serial bus, allowing a microcontroller to monitor switches, read a keypad matrix, drive indicators, or control auxiliary signals without dedicating one host pin to every function. The ADP5585 combines this general-purpose expansion role with dedicated keypad-scanning and programmable-logic functions. The ADP5585 provides 10 configurable I/Os and a 16-event FIFO. Its keypad capability can decode a matrix as large as 6 × 5, reducing the number of host pins and GPIO connections needed for human-interface controls. Programmable logic adds local digital behavior, while the reset generator and PWM generator broaden the device beyond simple level translation or GPIO expansion. The ADP5585ACBZ-01-R7 option is identified in the Analog Devices datasheet as a configuration intended for a larger 6 × 5 keypad matrix. The integrated FIFO retains event identifiers so software can retrieve recorded keypad events sequentially. This is particularly useful when the host processor must perform other processing between scans or when debounce and event handling need centralized firmware control. Typical uses include portable-device keypads, camera controls, remote-control panels, healthcare interfaces, and industrial instrumentation. The same device can support general digital I/O expansion when a keypad matrix is not required. Its small 1.59 mm × 1.59 mm 16-WLCSP package is suited to space-constrained systems, although careful PCB layout and assembly planning are necessary because of the fine package geometry. Designers should confirm the exact pin assignments, electrical limits, serial-interface settings, and supported keypad configuration against the manufacturer datasheet before layout release. Because the verified source data does not expose a public pin table or complete electrical limits in the supplied excerpts, unavailable values should be confirmed from the official ADP5585 datasheet rather than inferred from the orderable MPN.
ADP5585ACBZ-02-R7 10-I/O Keypad Controller | Analog Devices
Analog Devices ADP5585ACBZ-02-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, PWM generator, and a 16-event FIFO, housed in a 16-ball WLCSP package measuring 1.59 mm by 1.59 mm. The device communicates with a host processor through an I2C-compatible interface and includes ten configurable I/O resources that can support keypad scanning and general digital input/output expansion. The -02 configuration is identified by the verified distributor listing as the no-pullup option. An I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a microcontroller or embedded processor. The ADP5585 belongs to the broader hierarchy of I/O expander, interface IC, and semiconductor. In addition to conventional digital I/O expansion, this device incorporates dedicated keypad-scanning, programmable logic, reset, PWM, and event-recording functions, allowing a host to offload repetitive peripheral monitoring and conserve processor bandwidth. The principal verified features include 10 configurable I/Os and a 16-element event FIFO for recording keypad events. The FIFO allows the processor to read recorded events through the I2C-compatible interface instead of continuously polling every matrix input. Programmable logic and a PWM generator provide additional peripheral functions without requiring separate devices, while the reset generator supports system control functions. The -02 ordering option is specifically listed as a no-pullup keypad controller configuration. Internally, the ADP5585 combines programmable digital I/O resources with a keypad matrix decoder and event-recording architecture. A larger matrix can be configured with related -01 ordering options, but the exact supported matrix arrangement and event identifiers depend on the selected pins and configuration. Because the target -02 option omits pullups, external input conditioning or pullup resistors may be required wherever the scanned keypad or digital input interface does not otherwise establish the required high state. The host should configure the device through its register interface before relying on advanced functions. Typical uses include compact keypad interfaces in remote controls, medical and industrial instrumentation, consumer appliances, and portable equipment. Its small 1.59 mm by 1.59 mm WLCSP footprint is particularly useful when board area is constrained. The device can also reduce host pin count by combining keypad scanning, discrete digital I/O, programmable logic, reset generation, and PWM generation in one package. Suitable companion components include host microcontrollers, I2C bus devices, keypad matrices, and analog or mixed-signal front ends. Designers should account for the no-pullup configuration of the -02 option and confirm the external resistors required by the selected keypad topology. I2C pullups and all supporting pullup networks should be calculated for the actual bus voltage, speed, capacitance, and number of connected devices. Layout must preserve short, clean I2C routing and adequate ground return paths in the compact WLCSP footprint. Software should use the FIFO and interrupt mechanism to avoid unnecessary polling and should test event behavior across the configured matrix. This page combines verified manufacturer and distributor information with a practical feature analysis, same-brand drop-in assessment, pinout limitation, application guidance, and design notes. It distinguishes confirmed capabilities from electrical parameters that require the full manufacturer datasheet, helping engineers make a defensible sourcing and design decision.
ADP5585ACBZ-04-R7 - 10-I/O Key Controller | Analog Devices
The Analog Devices ADP5585ACBZ-04-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and PWM generator, supplied in a 16-WLCSP package measuring 1.59 mm by 1.59 mm. It is designed to add configurable input/output and keypad-scanning functions to compact embedded systems while limiting external controller pin count. An I/O expander is an interface IC that extends the number of digital inputs and outputs available to a host microcontroller through a serial interface. In the broader device hierarchy, the ADP5585 belongs to the I/O expander class of interface ICs and combines general-purpose GPIO expansion with dedicated keypad decoding, programmable logic, reset, and PWM functions. This integration is particularly useful in portable devices, remote controls, cameras, healthcare equipment, and industrial instrumentation. The verified product information identifies 10 configurable I/O ports, a built-in keypad matrix decoder, programmable logic, a reset generator, and a PWM generator. The -04 configuration is presented by DigiKey as keypad and I/O-expansion functionality, while Mouser identifies it as a 10-GPIO/key-controller device without pull-up resistors. These integrated functions can reduce the number of discrete logic, keypad-scanning, and reset components required in a compact design. The ADP5585 architecture separates several system-control tasks into one interface device. Programmable logic can implement local input relationships, the keypad decoder can organize matrix-scanned events, the reset generator can support controlled peripheral initialization, and the PWM generator can provide a configurable modulation output. Exact operating voltage, current consumption, serial-interface timing, programmable-logic limits, and electrical timing values are not included in the supplied verified excerpts and must be confirmed in the manufacturer datasheet before design release. Typical applications include handheld keypads, camera controls, remote-control interfaces, portable medical-device panels, and compact industrial instruments. The 16-WLCSP package is appropriate when board area is constrained, although its fine pitch requires careful PCB layout, inspection, and assembly-process control. The lack of integrated pull-ups must also be considered when the external bus or keypad arrangement requires them. Designers should verify the exact -04 keypad configuration, required external pull-ups, exposed-pad connection, and recommended decoupling directly from the Analog Devices datasheet. Because this WLCSP package has no matching entry in the available package-diagram library, the product page uses the default package illustration rather than claiming a verified 16-ball pin map. This page consolidates verified manufacturer and distributor information, pricing evidence, same-family configuration choices, and practical integration considerations. It also distinguishes confirmed functions from parameters that require engineering review, providing a more useful sourcing and design starting point than distributor listings alone.
ADP5585ACPZ-00-R7 - 10-I/O Keypad Controller | Analog Devices
The Analog Devices ADP5585ACPZ-00-R7 is a 10-I/O port expander with built-in keypad matrix decoder, programmable logic, reset generator, and PWM generator, supplied in a 16-LFCSP 3x3 mm package. The device is designed for portable and embedded systems that need additional input/output pins, key-event handling, or auxiliary control functions without increasing the host processor pin count. An I/O expander is an interface IC that increases the number of general-purpose inputs and outputs available to a host processor. The ADP5585 family combines this port-expansion function with a keypad matrix decoder and programmable logic, allowing a processor to scan keypad inputs and receive buffered events while using fewer host pins. This makes the device suitable for product interfaces, handheld equipment, industrial instrumentation, and other control systems with compact human-machine interfaces. The verified product information identifies 10 configurable I/Os, a 16-element FIFO for event recording, a built-in keypad decoder, programmable logic, a reset generator, and a PWM generator. The ADP5585ACPZ-00-R7 is specifically identified as the standard address configuration. The manufacturer datasheet also states that the 7-bit device address is 0x34 for all models except ADP5585ACPZ-03-R7, which uses 0x30. The 16-LFCSP 3x3 mm package supports compact PCB layouts in space-constrained portable products and instrument panels. Because the supplied web results do not publish the complete pin names or detailed electrical limits in machine-readable form, the package pinout and several electrical parameters are marked as requiring verification from the manufacturer datasheet before schematic capture or layout release. Typical applications include keypad entry, camera controls, remote controls, portable devices, healthcare equipment, industrial instrumentation, and other embedded human-interface systems. The internal FIFO can record input events while the host processes other tasks, while programmable logic can provide local decision-making or control behavior. The PWM generator is useful for LED indicators, simple dimming, or other low-frequency auxiliary functions when its electrical limits are appropriate for the load. Designers should confirm the I/O voltage, absolute maximum ratings, address configuration, capacitor requirements, and exposed-pad connection directly from the manufacturer datasheet. The I/O pins should also be checked for pull-up, pull-down, keypad, logic-level, or push-pull requirements before they are assigned to a board layout. This page combines verified manufacturer and distributor information with practical application guidance and explicitly identifies values that require datasheet confirmation.
ADP5585ACPZ-01-R7 - 10-I/O Keypad Controller | Analog Devices
Analog Devices ADP5585ACPZ-01-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and PWM generator in a 16-LFCSP (3 x 3 mm) package. The device provides an I2C address of 0x34, 10 configurable I/Os, and event-recording capability through a 16-element FIFO. It is designed to increase the I/O capacity of a host processor while reducing the number of GPIO pins required for keypad scanning and auxiliary control functions. An I/O expander is an interface IC that extends the number of digital input and output lines available to a processor through a serial bus. In the product hierarchy, the ADP5585 is an I/O expander, an interface IC, and a power-management-adjacent system-support semiconductor. Its integration of keypad scanning, programmable logic, reset generation, and PWM generation can replace several discrete peripheral functions while conserving host-controller pins. The principal features include 10 configurable I/Os, a keypad matrix decoder supporting programmable scan operations, a 16-element FIFO for event recording, programmable logic, and a dedicated PWM generator. These functions are useful in handheld products, remote controls, cameras, healthcare equipment, industrial instrumentation, and human-interface panels. The integrated architecture reduces component count and can simplify firmware by moving repetitive scanning and event handling into dedicated hardware. Communication occurs through I2C-compatible serial transactions. According to the manufacturer datasheet, a transaction begins with a start condition, followed by the 7-bit device address and read/write bit. For ADP5585ACPZ-01-R7, the device address is 0x34, distinguishing it from the ADP5585ACPZ-03-R7 version, which uses 0x30. The part acknowledges the address byte by pulling the data line low, allowing the host to confirm that the target device is present and responding. Typical uses include portable-device keypads, camera control interfaces, remote-control panels, medical monitoring equipment, and industrial instrumentation. In each case, the device can manage multiple digital lines and matrix-scanning tasks while the main processor handles higher-level application logic. In designs requiring multiple PWM outputs, the internal generator reduces the need for external PWM circuitry, although exact timing, current, and configuration limits must be taken from the manufacturer datasheet. The principal design consideration is firmware and bus planning. Because the -01 and -03 order codes use different 7-bit I2C addresses, multiple identical devices can coexist on one bus if address selection and pull-up requirements are managed correctly. Firmware should also account for FIFO overflow conditions, event ordering, and the difference between input, output, and keypad-scanner configurations. The 3 x 3 mm LFCSP package requires a qualified land pattern and careful inspection because its small dimensions make solder bridging and assembly defects a concern. This product page consolidates verified manufacturer descriptions, distributor availability, family-level alternatives, interface details, and practical design guidance. It distinguishes confirmed ADP5585 features from parameters that still require verification in the manufacturer datasheet, helping engineers assess fit before beginning a PCB layout or firmware implementation.
ADP5585ACPZ-03-R7 - 10-I/O Keypad Controller | Analog Devices
Analog Devices ADP5585ACPZ-03-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and PWM generator, supplied in a 16-LFCSP package. The device operates from a 3.6 V supply according to distributor data and communicates with a host processor through an I2C interface. Its ten configurable I/Os allow digital input, digital output, keypad scanning, or mixed functions to be assigned through registers. The ACPZ-03-R7 option uses the I2C device address 0x30, while other ADP5585 models use 0x34. An I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a microcontroller or system processor. It sits between the host and external controls, allowing a device with limited pin count to operate keypads, indicators, interlocks, and other digital peripherals. The ADP5585 expands this role by including a keypad matrix decoder and programmable logic, reducing the host burden associated with scanning switch matrices and recording button events. Key verified features include 10 configurable I/Os, a built-in keypad matrix decoder, programmable logic, a reset generator, and a PWM generator. A 16-element FIFO supports event recording, allowing qualifying input events to be retained and transferred over the serial interface. The device is intended for portable equipment such as phones, remote controls, and cameras, as well as non-portable healthcare, industrial, and instrumentation systems. The ADP5585 combines GPIO expansion with peripheral functions in one small package. Its I2C control path provides a practical way to add external interfaces without assigning a dedicated host GPIO to every keypad line or status indicator. Register-programmable behavior allows the same device family to support different board layouts, while the reset and PWM blocks reduce the need for separate discrete functions in compact control systems. The target suffix identifies the 16-LFCSP, 3 x 3 mm, tape-and-reel configuration. The ACPZ-03-R7 version is distinguished from other ADP5585 variants primarily by its device address and detailed configuration options. Because the I2C address differs from 0x34, firmware and bus planning should specifically account for the 0x30 address of this ordering code rather than assuming the address used by every other device in the family. Designers should confirm pin functions, exposed-pad requirements, address selection, and electrical limits directly against the manufacturer datasheet before layout release. I2C pull-up placement, bus capacitance, level compatibility, and the exposed thermal and electrical pad connection must be evaluated on the complete board rather than in isolation. This page consolidates the verified manufacturer function description, distributor ordering data, package information, I2C-address distinction, and family cross-references into one engineering-focused record. It also identifies which replacement details remain unverified, helping engineers distinguish confirmed pin-compatible family references from assumptions that would require schematic, firmware, and datasheet review.
ADP5586ACBZ-00-R7 - 10-I/O Keypad Decoder | Analog Devices
The Analog Devices ADP5586ACBZ-00-R7 is a 10-input/output port expander with a built-in keypad matrix decoder, programmable logic, reset generator, and pulse generators in a 16-WLCSP package measuring 1.59 mm by 1.59 mm. The device supports I2C communication up to 1000 kHz and operates from a supply rated up to 3.6 V. Its default configuration supports keypad-entry and general-purpose I/O expansion without requiring a dedicated host GPIO pin for every external signal. An I/O expander is an interface IC that increases the number of inputs and outputs available to a microprocessor or microcontroller. The ADP5586 belongs to the interface IC hierarchy and combines an I2C-controlled GPIO expansion function with keypad scanning, event processing, and dedicated timing logic. This combination can reduce host pin count while supporting matrix keypads, discrete controls, indicators, and other low-speed peripheral signals. Key features include 10 configurable I/O resources, an integrated keypad matrix decoder, programmable logic, a reset generator, and pulse generators. The I2C interface operates up to 1000 kHz, making the device suitable for systems that need compact peripheral expansion and organized keypad event handling. The -00 configuration is identified as the default-config variant, while the separate -01 product model changes how the RST pin is used. Technically, the device separates host interface traffic from keypad-scanning and programmable I/O functions. Its reset behavior provides controlled initialization, while pulse-generation and programmable-logic functions can reduce repetitive host firmware. According to the manufacturer datasheet, the RST pin includes a debounce filter. The -01 model uses that pin as an additional R5 keypad row, whereas the selected -00 model retains the documented reset-related behavior. Typical applications include portable-device keypads, remote controls, camera controls, healthcare panels, industrial instrumentation, and compact human-interface systems. It is most useful when a design needs several discrete inputs plus a matrix keypad but has limited host-controller GPIO pins. Because the device targets compact, mixed-signal control panels rather than high-speed peripheral buses, board-level I2C routing and exposed-pad assembly are important practical considerations. Designers should review the WLCSP land pattern, exposed-pad requirements, I2C pull-up placement, and the difference between the -00 and -01 RST configurations before release. A clean bypass-capacitor layout and short I2C traces help preserve signal integrity in dense portable or industrial equipment. This page combines verified manufacturer and distributor information with application guidance, selection criteria, and explicit uncertainty notes where detailed operating values or drop-in replacements were not provided.
ADP5586ACBZ-01-R7 - 10-I/O Keypad Decoder | Analog Devices
The Analog Devices ADP5586ACBZ-01-R7 is a 10-input/output port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and pulse generators, packaged in a 16-WLCSP measuring 1.59 mm × 1.59 mm. It supports I2C communication up to 1000 kHz and is identified as a 3.6 V device. An I/O expander is a specialized interface IC that increases the number of inputs and outputs available to a host processor. It belongs to the hierarchy of interface IC, peripheral interface controller, and system semiconductor. The ADP5586 combines general-purpose port expansion with a dedicated keypad matrix decoder, making it useful where a system needs both configurable digital lines and matrix keypad scanning without allocating many host GPIO pins. The device provides 10 configurable I/O resources and supports a 6-row by 5-column keypad matrix. Additional onboard functions include programmable logic, reset generation, and pulse generation. The ADP5586ACBZ-01-R7-specific configuration assigns the active-low RST pin as an additional keypad row, R5, while the SW_RESET register bit or an undervoltage condition provides another reset path. The I2C interface operates at up to 1000 kHz, allowing efficient host communication for register configuration and real-time input monitoring. Its compact 16-WLCSP format reduces PCB area compared with a larger discrete keypad-scanning implementation, but its fine pitch requires careful PCB layout, inspection, and assembly planning. Analog Devices identifies the ADP5586 family as production product. Typical uses include portable-device keypads, remote controls, cameras, healthcare equipment, industrial control panels, and instrumentation. In each case, the device can scan a matrix keypad while exposing additional programmable lines for LEDs, control inputs, or other digital functions. Integrating these tasks in one package can reduce host GPIO usage and simplify the system interconnect. Designers should verify the exact pin functions, voltage limits, logic thresholds, and configuration registers against the manufacturer datasheet before layout. A low-noise supply and appropriately placed decoupling capacitors remain important because the device combines digital I/O, keypad scanning, and host-interface functions in one compact package. This product synthesis consolidates verified manufacturer and distributor information, a 16-WLCSP package description, current pricing references, pin-specific reset behavior, and application guidance. It also clearly distinguishes the target ordering code from broader ADP5586 family information and identifies where additional engineering verification is still required.
ADP5586ACBZ-03-R7 - 10-I/O Keypad Decoder | Analog Devices
Analog Devices ADP5586ACBZ-03-R7 is a 10-input/output port expander with a built-in keypad matrix decoder, programmable logic, reset generator, pulse generators, and a 16-event FIFO in a 16-WLCSP package measuring 1.59 mm by 1.59 mm. The device communicates with a host processor through an I2C-compatible interface, allowing keypad and general-purpose I/O functions to be added without using a dedicated host I/O pin for every connection. An I/O expander is an interface IC that increases the number of digital input and output pins available to a microprocessor or microcontroller. Its place in the hierarchy is interface controller → I/O expander → keypad decoder → integrated circuit. By combining general-purpose I/O with automatic keypad scanning and event buffering, the ADP5586 reduces the polling burden on the host processor and can lower processor activity during keypad use. The verified product information identifies 10 configurable I/O resources, programmable logic, pulse-generation functions, an integrated reset generator, and a FIFO capable of storing up to 16 events. The -03 configuration uses the I2C-compatible interface and provides a default configuration identified by distributor listings. This combination makes the device useful where a compact keypad, discrete controls, or mixed digital I/O must be connected through a small number of serial interface pins. The ADP5586 architecture separates keypad decoding from the host processor. Keypad events can be captured in the 16-event FIFO and read over the serial interface, rather than requiring the processor to identify every press continuously. The programmable logic and pulse generators can support additional control functions, although individual timing limits, logic configurations, and I/O electrical characteristics must be confirmed in the manufacturer datasheet before final design release. Typical uses include portable-device keypads, camera controls, remote-control panels, healthcare user interfaces, industrial instrumentation, and compact control modules. In each case, the 16-WLCSP footprint conserves board area, while the integrated keypad decoder can reduce firmware complexity. Systems requiring more general-purpose I/O than the ADP5586 provides can use a dedicated I/O expander such as PCA9536DR alongside the keypad function. Designers should verify I2C address configuration, pull-up requirements, supported input and output drive levels, and the behavior of the RST and configuration pins in the Analog Devices ADP5586 Data Sheet (Rev. 0). Because the package is only 1.59 mm by 1.59 mm, PCB assembly should use suitable fine-pitch assembly capability, controlled solder-paste deposition, and inspection appropriate for the exposed land pattern. This product page combines verified manufacturer and distributor information, a 16-event FIFO feature, package details, purchasing data, and engineering-oriented usage guidance. It also identifies the important limitation that the verified cross-reference results do not establish five distinct pin-compatible replacements for the -03 configuration, avoiding unsupported drop-in claims.
ADP5587ACBZ-R7 - 18-GPIO I/O Expander | Analog Devices
The Analog Devices ADP5587ACBZ-R7 is a production mobile I/O expander and QWERTY keypad controller with 18 GPIO resources, a 400 kHz I2C interface, and 1.65 V to 3.6 V operation in a 25-WLCSP package measuring approximately 1.97 mm by 1.97 mm. It consolidates keypad scanning and additional digital I/O where a host processor has limited direct GPIO capacity. An I/O expander is an interface IC that extends a processor's input/output capacity over a serial bus. In the product hierarchy, the ADP5587 is an I/O expander, then a serial interface device and an integrated circuit. The ADP5587 adds value beyond ordinary GPIO expansion because its eight configurable GPIOs can operate as keypad rows or columns, while the remaining lines support general-purpose inputs, outputs, and interrupt signaling. Key features include support for an 18-GPIO configuration or a 10-by-8 keypad matrix, I2C auto-increment, an open-drain interrupt output, programmable pull-ups, key-press and key-release interrupts, a key-event counter with overflow indication, keypad locking, and a 275 microsecond debounce interval. These functions reduce host-side scanning logic while preserving event-driven communication with the processor. The device is designed around low-voltage mobile systems. Its I2C host interface runs at 400 kHz, and its 1.65 V to 3.6 V operating range suits compatible mobile and embedded rails. The compact WLCSP construction supports space-constrained handheld layouts, although its fine-pitch footprint demands careful PCB assembly, clean supply bypassing, and pin-accurate layout according to the Analog Devices package drawing. Typical uses include QWERTY keypad controllers, mobile handsets, portable navigation equipment, compact industrial user-interface panels, and other embedded products that need a dense matrix of switch inputs or additional GPIO lines. The host processor reads key events and configuration registers through I2C, while the interrupt line provides an event-driven indication of relevant key activity. For layout, keep I2C routing short, provide the required decoupling close to the supply pins, and verify the exposed-pad connection and assembly requirements in the manufacturer datasheet. Pull-ups must match the host voltage, bus capacitance, and timing budget. Software should also account for debounce, interrupt level programming, and event-counter overflow behavior. This page consolidates verified manufacturer and distributor facts, strict package constraints, application guidance, and clearly flagged data gaps. It distinguishes documented drop-in candidates from broader functional equivalents so engineers do not mistake a different footprint or feature set for a true PCB-level replacement.
ADP5587ACPZ-1-R7 - 18-GPIO I/O Expander | Analog Devices
The Analog Devices ADP5587ACPZ-1-R7 is an 18-GPIO I/O expander and QWERTY keypad controller with an I2C interface operating up to 400 kHz, packaged in a 24-LFCSP-WQ 4 mm × 4 mm package. It is designed for mobile platforms where the main processor has limited GPIO capacity and needs additional inputs, outputs, and keypad scanning functions. The verified distributor listing identifies the device as an 18-I/O expander with keypad-scanner functionality and a 400 kHz I2C interface. An I/O expander is an interface IC that increases the number of general-purpose input/output lines available to a host processor. The ADP5587 supports mobile keypad architectures by combining configurable GPIOs with keypad row and column functions, reducing the number of host pins required for physical key matrices. Its position in the hierarchy is GPIO expander → keypad controller → interface IC → semiconductor. The ADP5587 family is intended for QWERTY-type phone designs and similar human-interface systems. Its GPIO expansion capability allows the host to scan controls, read switch states, drive indicator or control lines, and manage keypad rows and columns through the serial interface. The I2C interface with auto-increment supports efficient register access, while the compact 24-LFCSP-WQ package supports space-constrained mobile equipment. The verified data does not provide complete electrical limits, pin-level functions, or timing values, so those parameters remain marked for data completion rather than inferred. Typical applications include mobile phone keypads, portable navigation devices, handheld terminals, compact consumer equipment, and other products that need more host-controlled I/O than the processor exposes directly. The ADP5587 is particularly useful when a design needs both general-purpose digital lines and keypad scanning in one device. Compared with a pure GPIO expander, it adds keypad-oriented functions; compared with a larger host MCU, it can reduce processor pin count and centralize human-interface I/O. Designers should verify the package-specific pinout, I2C address configuration, voltage limits, and electrical timing against the manufacturer datasheet before layout. The compact WQ package also requires careful PCB escape routing and thermal assessment according to the manufacturer’s recommended land pattern. This page combines verified distributor availability and product descriptions with structured application guidance and clearly identifies parameters that require datasheet confirmation.
ADP5587ACPZ-R7 - 18-GPIO Mobile I/O Expander | Analog Devices
The Analog Devices ADP5587ACPZ-R7 is a mobile I/O expander and QWERTY keypad controller with 18 GPIOs, an 8×8 keypad matrix, and a 400 kHz I2C interface. It operates from 1.65 V to 3.6 V and is housed in a 24-lead LFCSP-WQ package measuring 4 mm × 4 mm. The device is designed to add key-scanning and general-purpose I/O capacity when a mobile processor has limited GPIO resources. An I/O expander is an interface IC that extends a host processor through a serial bus. The ADP5587 supports eight independently configurable general-purpose inputs and outputs plus keypad matrix functions, placing key scanning and decoding in a compact peripheral. In the system hierarchy, it is an I/O expander, interface IC, and mobile system peripheral. Its 400 kHz I2C rate allows the host to update I/O state while the integrated keypad logic handles scanning. The supplied manufacturer information identifies an 18-GPIO port expander, configurable GPIOs, and an 8-keypad-matrix implementation. It also provides keypad-lock functionality and operation to 3.6 V. These features make the device relevant to QWERTY phones and other compact portable systems where board area and host-pin count are constrained. The part uses an I2C interface with auto-increment, reducing host-side register-access overhead for sequential register updates. Its 2 mm × 2 mm core package description in the manufacturer snippet corresponds to the compact class of device intended for mobile designs, while distributor records identify the ordering code as a 24-LFCSP-WQ, 4 mm × 4 mm package. Exact pin names, electrical limits, and register details require the official datasheet rather than distributor summaries. Typical uses include QWERTY keypad scanning, mobile navigation controls, compact wearable interfaces, portable measurement controls, and industrial panels requiring additional GPIO. The device can reduce direct processor connections, although the I2C bus and interrupt behavior must be checked against the host system requirements. When designing around the ADP5587, first verify the exact ACPZ pinout, exposed-pad connection, voltage limits, and decoupling requirements in the Analog Devices datasheet. Confirm that the host I2C voltage, address configuration, and keypad matrix geometry match the intended board. This page combines verified manufacturer and distributor information, lifecycle context, package details, commercial questions, and engineering-oriented design guidance. It also distinguishes confirmed drop-in alternatives from functional equivalents that may require different packages or pin assignments.
ADP5588ACPZ-R7 - 18-GPIO Mobile Keypad Controller | Analog Devices
The Analog Devices ADP5588ACPZ-R7 is a 3.0 V mobile I/O expander and QWERTY keypad controller with 18 configurable GPIOs, dual light-sensor inputs, and an I2C interface, housed in a 24-LFCSP-WQ package measuring 4 mm × 4 mm. It supports keypad configurations up to 10 × 8 and integrates key scanning, decoding, and interrupt handling to conserve host-processor GPIO resources. An I/O expander is an interface IC that extends the number of digital input and output lines available to a host controller. A keypad controller adds matrix-scanning and event detection, while an I2C interface IC connects compact peripheral logic to a processor bus. Within the hierarchy of interface ICs, this device reduces wiring and pin demand in mobile, wearable, and compact embedded systems. Key features include 18 GPIOs configurable as inputs, outputs, keypad rows, or keypad columns; two dedicated light-sensor inputs; I2C register-read autoincrement; programmable pull-ups; keypad locking; an open-drain interrupt output; and key-press and key-release interrupts. The GPI interrupt also supports programmable levels. These functions allow one controller to handle both a large keypad and additional discrete interface signals. The ADP5588 is designed for low-voltage mobile platforms. Verified manufacturer data specifies operation from 1.8 V to 3.0 V, while one distributor summary separately emphasizes 3.0 V operation. The compact 24-LFCSP-WQ package is suited to space-constrained boards, but its fine pitch requires careful PCB layout and assembly. Its I2C connection reduces host pins, although firmware must configure GPIO direction, pull-ups, interrupt behavior, and keypad dimensions. Typical uses include QWERTY keypad modules, handheld calculators, mobile accessories, wearable controls, light-sensor-equipped keypads, industrial key-entry panels, and custom HMI boards. The device can expand a processor with limited GPIO while providing dedicated key events through its interrupt output. Designers should verify the complete pinout, exposed-pad connection, address configuration, and supported I2C clock and voltage limits in the manufacturer datasheet. Place the device close to the keypad matrix, provide clean local decoupling, route I2C signals away from switching nodes, and validate signal levels and pull-ups across the complete system voltage range. This page consolidates verified distributor availability, manufacturer functionality, packaging data, purchasing information, and application guidance. It distinguishes documented functions from parameters that still require confirmation, helping engineers evaluate the ADP5588ACPZ-R7 without inferring missing electrical values.
ADP5588XCPZ-R7 - 18-GPIO Mobile I/O Expander | Analog Devices
The Analog Devices ADP5588XCPZ-R7 is a production 18-GPIO mobile I/O expander and QWERTY keypad controller operating from 1.8 V to 3.0 V in a 24-lead LFCSP-WQ package. It integrates an I2C interface, programmable key-event functions, dual light-sensor inputs, programmable GPIO configurations, and an open-drain interrupt output. The device is designed for keypad and alarm-system interfaces where a compact controller can scan matrix keys, monitor external signals, and report events to a host processor. An I/O expander is an interface IC that increases the number of inputs and outputs available to a host without requiring a processor with a large integrated GPIO package. In the hierarchy of electronic components, the ADP5588 belongs to the interface-IC class, specifically a mobile I/O expander and keypad controller. Its GPIO resources can be configured as general-purpose inputs, general-purpose outputs, keypad rows, or keypad columns, allowing one device to support multiple panel functions. Key features include support for an 18-GPIO port expander or a 10 × 8 keypad matrix, dual light-sensor inputs identified as C8 and C9, I2C register read autoincrement, keypad lock capability, and key-press and key-release interrupts. The open-drain interrupt output supports signaling to a connected controller, while programmable pull-ups and GPI level programmability provide flexibility for panel-level signal conditioning and interrupt behavior. The ADP5588 datasheet identifies the device as a mobile I/O expander and QWERTY keypad controller intended for keypad and alarm-system interfaces. Its 1.8 V to 3.0 V operating range suits low-voltage embedded systems. The I2C host interface reduces the number of dedicated processor pins, and the GPIO/keypad multiplexing helps consolidate keypad scanning, auxiliary input, and output functions into a compact controller. Typical applications include QWERTY keypad panels, alarm-system user interfaces, compact control panels, mobile equipment, and industrial HMI modules. In a keypad implementation, the device can scan matrix rows and columns while generating key-press and key-release events. The dual light-sensor inputs can also support panel functions where analog light sensing is required, although the verified excerpt does not provide their electrical characteristics. Designers should confirm the exact CPZ pin mapping, exposed-pad connection, I2C address configuration, pull-up values, and interrupt polarity in the manufacturer datasheet before layout. Keep I2C traces short, provide the required pull-ups, and account for the open-drain interrupt output. Since this is a digital interface IC, SOA is not applicable.
ADP5589ACBZ-00-R7 - 19-IO Keypad Decoder | Analog Devices
The Analog Devices ADP5589ACBZ-00-R7 is a 19-channel general-purpose input/output port expander with an integrated keypad matrix decoder, programmable logic, reset logic, and PWM generator, supplied in a 25-ball WLCSP package. The device operates from a 1.65 V to 3.6 V supply and can decode a keypad matrix as large as 11 rows by 8 columns. An I/O expander increases the number of digital inputs and outputs available to a host processor without requiring a large microcontroller package. The ADP5589 adds hardware-assisted keypad scanning to that conventional GPIO-expansion role, reducing firmware overhead in keypress, key-release, and keypad-lock applications. Its I/O pins can alternatively be programmed as GPI, GPO, or interrupt-capable inputs. Key features include 19 configurable I/Os, a 16-element event FIFO, key press and release interrupts, selectable interrupt levels, programmable 100 kΩ or 300 kΩ pull-up resistors, and 300 kΩ pull-down resistors. General-purpose outputs support push-pull or open-drain operation. Two programmable logic blocks extend the device beyond passive GPIO expansion, while internal and external PWM functions add mixed-signal timing capability. The ADP5589 is designed for portable equipment such as phones, remote controls, and cameras, as well as healthcare, industrial, and instrumentation systems. The serial interface reduces the number of host pins required when a design contains a matrix keypad, indicator LEDs, or additional control signals. Because the CBZ package is only 25 balls in an area smaller than most leaded packages, careful PCB layout is required for soldering, fanout, and signal integrity. Designers should verify I/O voltage limits, configure pull resistors for their external circuit, and reserve the interface pins for I2C communication and address selection. A 16-entry FIFO helps absorb asynchronous key events, but the host firmware must still process overflow and interrupt status. Because no verified cross-brand pin-compatible substitute was identified for the 25-ball CBZ footprint, replacement decisions should be based on an actual land-pattern and pin-function comparison rather than a similar GPIO-expander feature list. This page combines verified Analog Devices product information with distributor availability references, package analysis, application guidance, and a strict same-footprint replacement assessment that is not available from the manufacturer datasheet alone.
ADP5589ACBZ-01-R7 - 19 GPIO Channels | ADI Keypad Decoder
Analog Devices ADP5589ACBZ-01-R7 is a 19-channel GPIO port expander with an integrated keypad matrix decoder, programmable logic, reset logic, and PWM generator in a 25-ball WLCSP package measuring 1.99 mm by 1.99 mm. An I/O expander is an interface IC that increases the number of general-purpose inputs and outputs available to a host processor. In the product hierarchy, the ADP5589 belongs to the GPIO port expander and interface IC family, where it combines digital I/O expansion with dedicated keypad-scanning and event-management functions. This integration allows one serial interface to control a matrix keypad, additional digital lines, and programmable outputs while reducing the number of host GPIO pins required. The device provides 19 configurable I/O channels and includes a 16-element FIFO for recording key events. Its keypad decoder can handle matrix-keypad scanning up to 8 columns by 8 rows, or 8 by 8 as stated in the manufacturer documentation, and supports key press and release interrupts. Programmable logic, reset generation, and a PWM generator extend its use beyond simple bidirectional GPIO expansion. The ADP5589 is intended for portable equipment such as phones, remote controls, and cameras, as well as healthcare, industrial, and instrumentation systems. The same 25-ball WLCSP package helps limit board area in space-constrained products. A key advantage over a collection of discrete I/O and keypad-controller devices is the consolidation of scanning, event buffering, programmable functions, and general-purpose I/O into one interface IC. Typical uses include matrix-keypad decoding, consumer remote controls, camera controls, medical-device panels, industrial instrumentation interfaces, and portable electronic products. The manufacturer identifies portable and non-portable applications as the principal markets for I/O expanders of this type. Designers should verify the complete electrical limits, serial-interface timing, logic levels, programming model, and ball assignments in the Analog Devices ADP5589 datasheet before layout. Because the device is supplied in a 1.99 mm by 1.99 mm WLCSP, careful escape routing, clean ground return paths, and assembly-process planning are important implementation considerations. This page combines the verified manufacturer feature set, distributor pricing, source links, design guidance, and application analysis to provide practical information beyond a basic distributor catalog entry. All available pricing information is stated as of 2026-10-29, and unverified electrical details are identified rather than estimated.