ATF16V8C-7SI - 7.5ns 8-Macrocelle PLD | Microchip Technology
MPN: ATF16V8C-7SI ✓ פעילATF16V8C-7SI סקירה
A programmable logic device, or PLD, implements fixed digital logic functions that are configured in software rather than permanently connected with individual gates. The ATF16V8C family combines an 8-macrocelle architecture with multiple registered and combinational operating modes. Its architecture is a superset of generic 16R8 devices and can directly replace most 20-pin combinatorial PLDs, making it useful for compact control, decoding, address translation, and glue-logic designs.
The ATF16V8C-7SI provides a 7.5 ns maximum device speed, 8 macrocells, and approximately 300 gates. It supports a pin-controlled power-down option with 100 µA current. The manufacturer describes the family as CMOS and TTL compatible and identifies speed options down to 5 ns. Eight outputs are each allocated eight product terms, enabling more complex combinational functions than a basic dual-in-line PAL arrangement.
The device uses electrically erasable flash-memory technology, allowing its logic configuration to be programmed or erased without a dedicated programmer. Its 16V8 architecture supports complex logic functions configured automatically by software, while the 20-pin SOIC package supports conventional through-hole assembly and PCB compatibility with established 20-pin PLD designs.
Typical uses include industrial control and instrumentation, legacy interface decoding, programmable I/O expansion, embedded system address decoding, and compact peripheral-control logic. The ATF16V8C-7SI is especially relevant to brownfield equipment where an existing GAL16V8 or compatible 20-pin combinational PLD footprint must be retained.
When replacing an older GAL16V8, verify the configured fuse map, power-down behavior, termination requirements, and output timing. Although ATF16V8C devices are pin-to-pin and JEDEC fusemap compatible with GAL16V8 devices, AC and DC characteristics can contain minor differences that should be checked against the original design requirements.
This product record combines the ATF16V8C family architecture, package and speed details, drop-in replacement guidance, and practical design considerations into a focused guide for engineers maintaining or designing around 20-pin erasable programmable logic systems.
חלופות תחליף ישיר עבור ATF16V8C-7SI — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם ATF16V8C-7SI (אותו גורם צורה וטביעת רגל) — שונים ב Device Type, Package, Architecture, Configuration Technology.
ATF16V8C-7SU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATF16V8C-7SC
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATF16V8C-7SC
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATF16V8B-15SU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATF16V8C-7SI דירוגים מרביים ומאפיינים חשמליים
| Device Type | High-performance electrically erasable programmable logic device (PLD) |
| Architecture | 16V8 with 300 gates |
| Macrocells | 8 macrocells |
| Maximum Pin-to-Pin Delay | 7.5 ns |
| Family Maximum Pin-to-Pin Delay | 5 ns |
| Nominal Supply Voltage | 5 V |
| Industrial Supply Range | 5 V ± 10% |
| Commercial Supply Range | 5 V ± 5% |
| Pin-Controlled Power-Down Current | 100 µA |
| Configuration Technology | Electrically erasable EECMOS flash memory |
| Output Product-Term Allocation | 8 product terms per output |
| Logic Compatibility | CMOS and TTL compatible |
| מארז | 20-SOIC, 0.295 inch (7.50 mm) width |
| סוג הרכבה | Surface mount |
| Temperature Grade | Industrial grade |
מדריך תצורת פינים של ATF16V8C-7SI 20-soic, 0.295 inch (7.50 mm) width
תצורת פינים עבור ATF16V8C-7SI (מארזת 20-soic, 0.295 inch (7.50 mm) width). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.
אין נתוני פריסת פינים מפורטים עבור ATF16V8C-7SI.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
ATF16V8C-7SI מתאים עבור 6 יישוםs: Industrial Control Logic, Legacy GAL16V8 Replacement, Address and Bus Decoding, Programmable I/O Expansion, Instrumentation Signal Routing, Peripheral Control and Interlocks.
Industrial Control Logic
The ATF16V8C-7SI fits compact industrial control logic that combines decoding, state transitions, and output conditioning in one programmable device. Its eight macrocells and eight product terms per output provide enough capacity for multiple combinational functions, while the 7.5 ns maximum pin-to-pin delay supports moderate-speed control paths. The industrial-grade suffix and operation over 5 V ± 10% distinguish it from the commercial -7SU option. Use the manufacturer fuse map and configuration tools to implement the logic, and verify power-down-state outputs before connecting the device to external actuators.
מומלץ
Legacy GAL16V8 Replacement
ATF16V8C-7SI is suited to maintaining equipment built around GAL16V8-style combinational logic. Microchip identifies ATF16V8B and ATF16V8C devices as pin-to-pin and JEDEC fusemap compatible with GAL16V8 parts, allowing the existing 20-pin board architecture to be retained. The ATF16V8C-7SI also provides electrically erasable flash configuration and a 7.5 ns speed option. Before replacement, compare the original fuse map, power-down behavior, AC timing, and DC characteristics because the manufacturer notes that minor differences can exist between families.
מומלץ
Address and Bus Decoding
The ATF16V8C-7SI can implement address decoding, chip-select generation, and bus-control interlocks where a small number of Boolean terms are required. Its eight macrocells and 16V8 organization allow several outputs to be allocated across different decode functions, and the 7.5 ns pin-to-pin delay can support faster control sequences than the 15 ns ATF16V8B option. Account for output skew, setup time, and the configured operating mode when analyzing system timing. The 20-SOIC package also simplifies adoption in older through-hole equipment.
מומלץ
Programmable I/O Expansion
ATF16V8C-7SI can expand a legacy controller's discrete I/O logic by combining latch, decode, and output-enable functions in an erasable PLD. Eight product terms per output provide flexible Boolean implementation, while the pin-controlled power-down option can reduce consumption to 100 µA when a section is inactive. Use registered or combinatorial configuration according to the required timing behavior, and test every output during power transitions. A 15 ns ATF16V8B alternative may fit slower peripheral interfaces but does not provide equivalent timing margin.
מומלץ
Instrumentation Signal Routing
The ATF16V8C-7SI can route measurement-control signals, implement mode-selection logic, and generate enables for analog front ends in compact instrumentation. The 7.5 ns device speed helps minimize delay in control and select paths, while the industrial-grade target is better aligned with equipment operating outside the commercial temperature range than ATF16V8C-7SU. Configure the PLD only after identifying asynchronous inputs, metastability-sensitive paths, and outputs that must remain defined during power-down. Validate timing with the actual peripheral rather than relying only on the maximum pin-to-pin delay.
מומלץ
Peripheral Control and Interlocks
ATF16V8C-7SI is appropriate for relay and actuator sequencing interlocks in legacy industrial systems where a 20-pin PLD footprint is already established. Its eight macrocells can combine permissive logic, fault flags, and output-enable functions, while the 7.5 ns speed supports rapid sequencing of control outputs. Keep fail-safe behavior independent of programmed logic when the application requires a de-energized state during reset or power loss. Validate output states, supply tolerance, and timing margins across the full industrial supply range of 5 V ± 10%.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור ATF16V8C-7SI — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | ATF16V8C-7SU | ATF16V8C-7SC | ATF16V8C-7S | ATF16V8B-15SU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-SOIC (0.295 inch, 7.50 mm width) | 20-SOIC (0.295 inch, 7.50 mm width) | 20-SOIC (0.295 inch, 7.50 mm width) | 20-SOIC (0.295 inch, 7.50 mm width) | 20-SOIC (0.295 inch, 7.50 mm width) |
| Device Type | 16V8 electrically erasable PLD | 16V8 electrically erasable PLD | 16V8 electrically erasable PLD | 16V8 electrically erasable PLD | 16V8 electrically erasable PLD |
| Macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells |
| Maximum Pin-to-Pin Delay | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 15 ns |
| Gate Count | 300 gates | 300 gates | 300 gates | 300 gates | 250 gates |
| Configuration Technology | Electrically erasable EECMOS flash memory | Electrically erasable EECMOS flash memory | Electrically erasable EECMOS flash memory | Electrically erasable EECMOS flash memory | Electrically erasable EECMOS flash memory |
מבדילים עיקריים
- Faster timing within the same 20-SOIC footprint (לעומתATF16V8B-15SU)
- Industrial temperature-grade option (לעומתATF16V8C-7SU)
- Larger gate organization than the ATF16V8B alternative (לעומתATF16V8B-15SU)
הערות תכנון
Do not treat every 16V8 PLD as electrically interchangeable. The ATF16V8C family is a superset of generic 16R8 devices and can replace most 20-pin combinatorial PLDs, but the fuse map, output polarity, register configuration, and power-down behavior still need to match. For GAL16V8 migrations, compare the original configuration against the Microchip JEDEC fusemap and verify every output state during reset and power-down.
Design the 5 V supply for the ATF16V8C-7SI across the industrial range of 5 V ± 10%. Place the device's decoupling capacitor close to the supply pins and use a quiet source because configuration and system timing can be affected by supply ripple. If the 100 µA pin-controlled power-down mode is used, define its control logic so no output can produce an unintended command while the PLD is inactive.
Use the 20-SOIC footprint and pin assignments from the manufacturer datasheet rather than relying on a generic 20-pin PLD symbol. Verify orientation, supply-pin locations, programming access, and unused-pin treatment on the PCB. For systems that retain older GAL16V8 boards, compare the replacement device's AC and DC characteristics and check output timing because Microchip notes that minor family differences can exist.
Treat the 7.5 ns figure as a maximum pin-to-pin device specification rather than a guaranteed delay for every logic path. Configuration mode, product-term depth, output loading, temperature, and supply voltage affect real timing. In bus-decoding or interlock circuits, analyze worst-case path delay and output skew, and use ATF16V8B-15SU only when the slower 15 ns timing still satisfies the system requirement.
מידע על תאימות
The ATF16V8C product information confirms the logic-device category and industrial-grade 5 V option but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.
