BCM89501BPBG 7-Port BroadR-Reach Automotive Switch | Broadcom
MPN: BCM89501BPBG ✓ פעילBCM89501BPBG סקירה
An automotive Ethernet switch is an interface IC that connects multiple vehicle network nodes through Ethernet links. BroadR-Reach is a physical-layer networking technology used for automotive cabling, while the switch integrates network-port control and multiple transceivers on one device. BCM89501BPBG combines seven port positions with five integrated transceivers, providing a centralized interface for electronic control units, vehicle gateways, infotainment systems, and other networked automotive subsystems.
The primary feature of BCM89501BPBG is its combination of seven switch ports and five integrated Ethernet transceivers in one package. This integration reduces the number of separate interface devices required in a vehicle network and can simplify board partitioning. The 176-terminal square package uses gull-wing terminals for surface-mount assembly, allowing the device to connect mechanically to a multilayer PCB without through-hole insertion.
BCM89501BPBG is identified as an automotive-grade BroadR-Reach switching device, with AEC-Q100 screening associated with the product. AEC-Q100 is the automotive qualification framework used for integrated circuits, while RoHS compliance indicates control of specified hazardous substances in the component and its manufacturing process. The package also provides a high pin count suitable for multiplexing external network interfaces, internal controls, power connections, and signaling.
Typical automotive uses include central vehicle Ethernet gateways, body and chassis domain controllers, infotainment connectivity, driver-assistance subsystems, and electronic control-unit aggregation. The integrated switch can serve as a network concentration point when several Ethernet-based vehicle systems require a common switching fabric. Its BroadR-Reach support is especially relevant to automotive networks using physical-layer signaling over copper wiring.
Layout should treat BCM89501BPBG as a high-pin-count, high-speed interface device. Place all bypass and decoupling capacitors close to their intended power terminals, preserve short return paths beneath signal and supply planes, and follow the manufacturer’s reference layout and layer-stack guidance. Differential Ethernet pairs require controlled impedance, length matching, and continuous reference planes. The exposed thermal and power structure also requires adequate copper area and thermal vias where recommended.
This product summary distinguishes the BCM89501BPBG from generic seven-port Ethernet switches by combining BroadR-Reach automotive positioning, five integrated transceivers, AEC-Q100 screening, and a 176-terminal surface-mount package. It also consolidates package, lifecycle, compliance, sourcing, and application guidance so engineers can assess whether the device fits a specific vehicle-network architecture before beginning board-level implementation.
חלופות תחליף ישיר עבור BCM89501BPBG — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
אין חלופות תואמות Drop-in עבור מוצר זה.
בקשת חלופותBCM89501BPBG דירוגים מרביים ומאפיינים חשמליים
| Product Type | 7-port integrated BroadR-Reach automotive Ethernet switch |
| Number of Ports | 7 ports |
| Integrated Ethernet Transceivers | 5 transceivers |
| Network Technology | BroadR-Reach automotive Ethernet |
| Automotive Screening | AEC-Q100 |
| Package Terminal Count | 176 terminals |
| Terminal Form | Gull wing |
| Package Shape | Square |
| סוג הרכבה | Surface mount |
| Packaging Type | Tray |
| Standard Package Quantity | 1600 units |
| סטטוס RoHS | Supported |
| Manufacturer | Broadcom Limited |
מדריך תצורת פינים של BCM89501BPBG 1600 units
תצורת פינים עבור BCM89501BPBG (מארזת 1600 units). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור BCM89501BPBG.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
BCM89501BPBG מתאים עבור 6 יישוםs: Automotive Ethernet Gateway, Body and Chassis Controller, Infotainment Network Aggregation, Driver Assistance Systems, Electronic Control Unit Networking, Industrial Vehicle Network.
Automotive Ethernet Gateway
BCM89501BPBG fits a centralized vehicle Ethernet gateway that must aggregate connections from multiple automotive domains. Its seven switch ports provide a broad interface count, while five integrated transceivers reduce the number of separate physical-layer devices required on the board. The AEC-Q100-associated device and BroadR-Reach focus support evaluation in vehicle-network architectures. Implementation should follow the manufacturer layout for its 176-terminal surface-mount package, preserve controlled-impedance Ethernet routing, and validate power sequencing, data rates, cable reach, and EMC performance against the target vehicle platform.
מומלץ
Body and Chassis Controller
BCM89501BPBG can support body or chassis controller designs that connect doors, lighting, climate, seat, and other networked vehicle subsystems. Seven switch ports allow several Ethernet-based controllers to share a central network concentration point, and the five integrated transceivers are useful where the design expects copper-linked BroadR-Reach nodes. Engineers should confirm that each external node satisfies the required link standard and data rate. PCB implementation also requires careful high-pin-count assembly, short supply returns, uninterrupted reference planes, and differential-pair routing that follows the manufacturer’s layout guidance.
מומלץ
Infotainment Network Aggregation
BCM89501BPBG is applicable to infotainment systems that need to aggregate Ethernet traffic from multiple in-cabin domains. A single seven-port switch can reduce the number of discrete network-interface sections on the controller, while the integrated transceiver count supports copper-based automotive connectivity. Signal integrity is important at the package boundary because the device combines 176 terminals with high-speed network interfaces. Use the manufacturer’s recommended stack-up and land pattern, route differential pairs symmetrically, minimize vias, and verify EMC and data-rate margins for every connected infotainment node.
מומלץ
Driver Assistance Systems
BCM89501BPBG can be evaluated for driver-assistance subsystems that exchange data between cameras, radar controllers, displays, and domain computers over an automotive Ethernet network. Its seven ports suit centralized connectivity, while BroadR-Reach and integrated transceiver support align with copper-link vehicle networks. The component should be treated as an interface block within the larger sensing and compute architecture rather than as a processing device. System validation must cover latency, error handling, data rates, EMC immunity, cable reach, and failure behavior across the complete sensor network before the design is approved for vehicle use.
מומלץ
Electronic Control Unit Networking
BCM89501BPBG is suitable for centralized networking among distributed electronic control units when a vehicle architecture uses seven BroadR-Reach-capable links. Integrating five transceivers with the switching fabric can simplify the interface count on a main controller board and standardize connectivity across subsystems. Because automotive ECUs commonly impose strict diagnostic, power, and electromagnetic-compatibility requirements, the component should not be selected solely from port count. Verify protocol behavior, reset requirements, supply limits, temperature range, fault handling, and all 176 terminal assignments using the manufacturer documentation.
מומלץ
Industrial Vehicle Network
BCM89501BPBG can support industrial vehicle networks in construction, agricultural, or material-handling equipment where onboard electronic systems require centralized Ethernet connectivity. Its seven ports and five integrated transceivers provide a basis for aggregating multiple vehicle controllers over BroadR-Reach copper links, while AEC-Q100 screening is relevant to automotive-class requirements. The design team should still verify operating-temperature, vibration, power, EMC, and environmental requirements for the specific machine. Use a robust multilayer layout, maintain Ethernet impedance, provide clean local supply distribution, and avoid unreviewed board substitutions.
מומלץ
נתוני עזר הנדסיים עבור BCM89501BPBG — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Brand | Broadcom |
| Package | 176-terminal square gull-wing surface-mount package |
| Number of Ports | 7 ports |
| Integrated Transceivers | 5 Ethernet transceivers |
| Network Technology | BroadR-Reach automotive Ethernet |
| Automotive Screening | AEC-Q100 |
| Terminal Count | 176 terminals |
| Packaging | Tray, 1600 units |
| RoHS Status | Supported |
מבדילים עיקריים
- Seven-port automotive network concentration in one device (לעומתNo verified drop-in alternative)
- Five transceivers integrated with the switching function (לעומתNo verified drop-in alternative)
- Automotive-oriented qualification and compliance positioning (לעומתNo verified drop-in alternative)
הערות תכנון
Use the exact BCM89501BPBG land pattern and layer stack from the manufacturer package drawing when laying out the 176-terminal gull-wing package. Place bypass and decoupling capacitors at the intended power terminals, provide short and direct supply and ground connections, and preserve uninterrupted reference planes beneath the device. Because this is a high-pin-count automotive interface IC, assembly tolerances, via-in-pad practices, and soldering-profile requirements should be reviewed against the package documentation rather than inferred from a generic footprint.
Route all Ethernet differential pairs as controlled-impedance, tightly coupled nets on a continuous reference plane. Match intra-pair geometry and maintain the length relationships required by the manufacturer’s interface guidelines. Minimize layer transitions and stubs, and avoid placing high-current or switching-node paths beneath sensitive pairs. Validate the completed board with signal-integrity simulation or measurements because the public product information identifies the BroadR-Reach interface but does not provide the detailed rise-time, impedance, or channel-loss limits needed for an independent channel design.
Partition vehicle supply networks carefully before powering BCM89501BPBG. Follow the manufacturer’s recommended input capacitance, supply sequencing, and power-up behavior, and isolate noisy loads from sensitive interface circuitry. Verify the complete vehicle harness and load-dump behavior against the device’s electrical limits in the manufacturer datasheet. The available product listings confirm seven ports, five transceivers, AEC-Q100 screening, and the package construction, but they do not state the permitted supply range or quiescent current, so those values must not be assumed during rail design.
Allocate adequate copper area and thermal-via coverage beneath and around BCM89501BPBG according to the manufacturer’s assembly guidance. Its 176-terminal package creates substantial routing complexity, but terminal count alone does not determine junction temperature. Thermal performance depends on the actual switching loss, ambient temperature, copper geometry, board area, and neighboring heat sources. Perform a board-level thermal assessment after stack-up and enclosure details are known, and use the datasheet’s electrical limits to calculate dissipation rather than treating the package as an unrestricted thermal solution.
Do not treat a distributor or cross-reference result as proof of drop-in compatibility. A genuine replacement for BCM89501BPBG must use the same 176-terminal footprint, preserve pin assignments, support the required BroadR-Reach media and data rates, and satisfy the application’s automotive qualifications. No verified substitute met those conditions in the available cross-reference results. Before redesigning around another device, compare every terminal function, supply requirement, timing characteristic, reset behavior, and thermal/mechanical constraint against the BCM89501BPBG datasheet.
מידע על תאימות
Product listings identify RoHS support and AEC-Q100 screening. No explicit REACH, lead-free, halogen-free, or conflict-minerals declaration was identified.