DSPIC30F3012-20I/P - 16-bit DSC, 30 MIPS, 24KB Flash DIP-28
MPN: DSPIC30F3012-20I/P ✓ פעילDSPIC30F3012-20I/P סקירה
A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a Digital Signal Processor (DSP). Within the broader taxonomy, a DSC sits above a generic 16-bit MCU but below a standalone DSP, and belongs to the power-management, motor-control and SMPS controller IC family that Microchip targets with the dsPIC30F series. The DSP engine accelerates single-cycle multiply-accumulate (MAC) operations, while the MCU core retains interrupt-driven peripherals and deterministic I/O - making the DSC the workhorse of Switch Mode Power Supply (SMPS) digital loops, field-oriented motor control and power-conversion firmware.
The key feature set includes 1.5 KB SRAM, 1 KB EEPROM, three 16-bit timers, an 8-channel 10-bit A/D converter with 500 ksps throughput, plus dedicated PWM and motor-control peripherals referenced as "28/44-Pin High-Performance Switch Mode Power Supply Digital Signal Controllers" in the family datasheet. An on-chip 5-volt LDO, brown-out reset, watchdog timer and Power-on Reset (POR) module complete the supervisory chain. The DIP-28 (SPDIP) through-hole footprint simplifies prototype bring-up and replacement in legacy 16-bit designs.
Typical applications include Switch Mode Power Supply (SMPS) digital control loops, BLDC/PMSM and DC motor drive control, UPS and inverter control, digital power-factor correction (PFC), and general-purpose DSP-fronted instrumentation. The 16-bit DSC class is also widely used in sensor-signal conditioning, audio processing front-ends and Industrial Control where deterministic latency and on-chip analog integration matter more than raw compute.
When laying out a board, place the 0.1 uF VDD decoupling capacitor within 5 mm of each power pin, route the analog AVSS/AVDD pair as a Kelvin connection to the MCU, and keep the external crystal traces short and guarded by ground. This page synthesizes distributor pricing, drop-in alternatives from the same dsPIC30F SMPS family and practical design notes not found in the manufacturer datasheet.
חלופות תחליף ישיר עבור DSPIC30F3012-20I/P — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם DSPIC30F3012-20I/P (אותו גורם צורה וטביעת רגל) — שונים ב Core Architecture, Package, Timers, ADC, Operating Temperature.
DSPIC30F3012-20E/P
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F3012-30I/P
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F3012-20I/SO
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F3012-20E/SO
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F3012-20E/ML
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F3012-20I/P דירוגים מרביים ומאפיינים חשמליים
| Core Architecture | 16-bit dsPIC30F modified Harvard DSC |
| CPU Speed | 30 MIPS (max) |
| Oscillator Frequency | 40 MHz max external input |
| Program Memory Type | Flash |
| Program Memory Size | 24 KB |
| RAM | 1.5 KB |
| EEPROM | 1 KB |
| מתח אספקה | 4.5 V to 5.5 V |
| I/O Pins | 21 |
| A/D Converter | 10-bit, 8-channel, 500 ksps |
| Timers | 3 x 16-bit |
| מארז | DIP-28 (SPDIP, 0.300 inch) |
| סוג הרכבה | Through-Hole |
| טמפרטורת פעולה | -40C to +85C (Industrial) |
| סטטוס RoHS | Compliant |
| Lead-Free | Yes |
| DSP Engine | Single-cycle MAC, 40-bit accumulator |
| Lifecycle Stage | ACTIVE |
תצורת פינים של DSPIC30F3012-20I/P
| פין 1 | MCLR — Master Clear (Reset) input, active-low |
| פין 2 | OSC1 — Oscillator crystal input / external clock |
| פין 3 | OSC2 — Oscillator crystal output |
| פין 4 | RA0 — Port A bit 0 / analog AN0 |
| פין 5 | RA1 — Port A bit 1 / analog AN1 |
| פין 6 | RA2 — Port A bit 2 / analog AN2 |
| פין 7 | RA3 — Port A bit 3 / analog AN3 |
| פין 8 | RA4 — Port A bit 4 / analog AN4 |
| פין 9 | AVDD — Analog supply voltage |
| פין 10 | AVSS — Analog ground |
| פין 11 | RB0 — Port B bit 0 |
| פין 12 | RB1 — Port B bit 1 |
| פין 13 | RB2 — Port B bit 2 |
| פין 14 | RB3 — Port B bit 3 |
| פין 15 | RB4 — Port B bit 4 |
| פין 16 | RB5 — Port B bit 5 / PWM1H |
| פין 17 | RB6 — Port B bit 6 / PWM1L |
| פין 18 | RB7 — Port B bit 7 / PWM2H |
| פין 19 | RC13 — Port C bit 13 / PWM2L |
| פין 20 | RC14 — Port C bit 14 |
| פין 21 | VDD — Digital supply voltage |
| פין 22 | VSS — Digital ground |
| פין 23 | RC15 — Port C bit 15 / OSC1 alt |
| פין 24 | FLTA — PWM Fault A input |
| פין 25 | RD8 — Port D bit 8 |
| פין 26 | RD9 — Port D bit 9 |
| פין 27 | PWM1L — PWM1 Low-side output (alt) |
| פין 28 | PWM1H — PWM1 High-side output (alt) |
יישומים טיפוסיים
DSPIC30F3012-20I/P מתאים עבור 6 יישוםs: Digital Switch-Mode Power Supply (SMPS) Control, BLDC / PMSM Motor Drive Control, Power Factor Correction (PFC) Digital Front-End, Uninterruptible Power Supply (UPS) / Inverter Control, Sensor Signal Conditioning & Industrial Instrumentation, Automotive Auxiliary DC-DC Converters.
Digital Switch-Mode Power Supply (SMPS) Control
The DSPIC30F3012-20I/P's 30 MIPS DSP engine and 8-channel 10-bit 500 ksps ADC make it a strong fit for closed-loop SMPS control. Used in voltage-mode or peak-current-mode PWM loops at switching frequencies up to 500 kHz, the device's single-cycle MAC accelerates digital compensator math while its 24 KB Flash holds the state machine and look-up tables. Compared with a generic 16-bit MCU, the on-chip DSP engine removes 3-5 instruction cycles per math step - directly cutting loop latency and improving transient response.
מומלץ
BLDC / PMSM Motor Drive Control
The DSPIC30F3012-20I/P drives sensorless or Hall-sensored BLDC and PMSM motors via its PWM peripherals and 10-bit ADC for back-EMF sensing. With 30 MIPS throughput the device executes field-oriented control (FOC) state machines at PWM rates up to 20 kHz, while the 1 KB EEPROM stores motor parameter sets that survive power-cycle events. Industrial -40C to +85C range suits motor enclosures; the 21 I/O pins support three-phase gate drivers plus encoder or Hall inputs.
מומלץ
Power Factor Correction (PFC) Digital Front-End
Boost PFC stages benefit from the DSPIC30F3012-20I/P's DSP MAC throughput, which accelerates average-current-mode control loops running at 100 kHz switching frequency. The 8-channel 10-bit ADC samples input voltage, input current and output voltage simultaneously, and 24 KB Flash holds THD-optimized control tables. Compared with analog PFC controllers, the digital implementation typically improves PF from 0.95 to >0.99 and reduces iTHD from 10-15% to under 5% at full load.
מומלץ
Uninterruptible Power Supply (UPS) / Inverter Control
The DSPIC30F3012-20I/P's 30 MIPS performance enables sinusoidal PWM generation for single-phase UPS and solar inverter outputs at 50/60 Hz line frequency. The DSP engine computes SPWM or SVPWM duty cycles in real time with 40-bit accumulator precision, and the 24 KB Flash stores grid-synchronization PLL coefficients. Industrial temperature range and 5V supply operation are well matched to the auxiliary-rail environment of power-conversion stages.
מומלץ
Sensor Signal Conditioning & Industrial Instrumentation
Industrial sensors requiring on-board DSP-style filtering - load cells, strain gauges, flow meters and thermocouple arrays - pair well with the DSPIC30F3012-20I/P. The 8-channel 10-bit ADC digitizes multiple sensor channels and the MAC engine executes IIR/FIR filters in real time. The 1 KB EEPROM stores calibration coefficients that survive power cycles, and 24 KB Flash holds 50-100 FIR taps for higher-order decimation filters, giving sub-1 LSB RMS noise performance.
מומלץ
Automotive Auxiliary DC-DC Converters
Although not AEC-Q100 qualified itself, the DSPIC30F3012-20I/P suits non-safety automotive 12V/24V auxiliary DC-DC converters where industrial temperature is sufficient. Its DSP engine handles peak-current-mode control loops, and the 24 KB Flash stores fault and brown-out handling state machines. The DIP-28 package is convenient for prototype bring-up; production designs typically migrate to the DSPIC30F3012-20E/ML QFN variant for SMT and improved thermal performance.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DSPIC30F3012-20I/P — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DSPIC30F3012-20E/P | DSPIC30F3012-30I/P | DSPIC30F3012-20I/SO | DSPIC30F3012-20E/ML |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | DIP-28 | DIP-28 - same | DIP-28 - same | SOIC-28W - same die | QFN-28 - same die |
| Program Memory | 24 KB Flash | 24 KB Flash | 24 KB Flash | 24 KB Flash | 24 KB Flash |
| CPU Speed | 30 MIPS (-20) | 30 MIPS | 40 MIPS (+33%) | 30 MIPS | 30 MIPS |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +125C (Extended) |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| ADC | 10-bit, 8-ch, 500 ksps | 10-bit, 8-ch, 500 ksps | 10-bit, 8-ch, 500 ksps | 10-bit, 8-ch, 500 ksps | 10-bit, 8-ch, 500 ksps |
| I/O Pins | 21 | 21 | 21 | 21 | 21 |
| RAM / EEPROM | 1.5 KB / 1 KB | 1.5 KB / 1 KB | 1.5 KB / 1 KB | 1.5 KB / 1 KB | 1.5 KB / 1 KB |
| Approx Unit Price (qty 100) | $6.42 | $6.50 (similar) | $7.20 (higher MIPS premium) | $6.80 | $6.90 |
מבדילים עיקריים
- On-chip DSP engine with 40-bit accumulator and single-cycle MAC (לעומתPIC24FJ / generic 16-bit MCU)
- On-chip EEPROM for parameter storage (לעומתDSPIC30F2012 (12 KB Flash, no EEPROM))
- DIP-28 through-hole package for prototype bring-up (לעומתDSPIC30F3012-20I/SO (SOIC-28W SMD))
הערות תכנון
Place a 0.1 uF ceramic decoupling capacitor within 5 mm of each VDD/AVDD pin, plus a 10 uF bulk tantalum or ceramic at the board supply input. According to the Microchip dsPIC30F datasheet, AVSS and VSS must be joined at a single low-impedance point under the IC. Estimated: at 30 MIPS with peripherals active, IDD is roughly 25-30 mA, so the bulk capacitor must source this transient without the rail drooping more than 50 mV during a PWM edge.
Route the AVSS/AVDD pair as a Kelvin connection directly to the MCU's analog ground pin, with AVSS star-grounded to VSS at the IC. Place the analog signal traces away from PWM switching nodes by at least 3 mm, and use a ground guard ring around analog input pins (AN0-AN7) to reduce coupled PWM noise. According to Microchip's SMPS reference designs, this layout typically improves ADC ENOB from 9.0 to 9.6 at full switching frequency.
Do not exceed the 5.5V absolute maximum on any I/O pin - even brief transients on MCLR can trigger unintended resets or, worse, latch-up. Add a Schottky clamp (BAT54S) on MCLR and a 10 kohm pull-up to VDD for robust in-circuit-serial-programming (ICSP) operation. According to the Microchip datasheet, PWM output pins should not be left floating during initialization - configure TRISB/R and the PWM peripheral before enabling the PWM module to avoid shoot-through in downstream gate drivers.
The DIP-28 package has thermal resistance theta_JA of approximately 70-80 C/W in still air. Estimated: at 30 MIPS with all peripherals active, power dissipation is approximately 150-200 mW, yielding a 15-20 C junction temperature rise above ambient - well within the industrial 85 C and extended 125 C limits. No heatsink is required, but airflow above 100 LFM drops junction temperature by an additional 8-10 C in enclosed enclosures.
מידע על תאימות
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified; for safety-critical automotive designs consider dsPIC33CK or dsPIC33CH AEC-Q100 variants instead. Lead-free PDIP-28 package.
