DSPIC30F6014A-20E/PF - 16-bit 20MIPS DSC, 144KB Flash | Microchip
MPN: DSPIC30F6014A-20E/PF ✓ פעילDSPIC30F6014A-20E/PF סקירה
A Digital Signal Controller (DSC) is a hybrid class of microcontroller that combines a modified Harvard MCU architecture with single-cycle DSP MAC (multiply-accumulate) instructions. DSCs sit between classical MCUs and dedicated DSPs in the silicon taxonomy, occupying the same role as MCUs before signal processing, and are classified as embedded processors/controllers (MCU -> 16-bit MCU -> DSC -> microcontroller IC) in the broader semiconductor hierarchy. dsPIC30F devices specifically target real-time control loops where cycle-deterministic DSP and MCU peripheral integration are both required.
Key features include 144 KB Flash, 8 KB SRAM, and 4 KB EEPROM for non-volatile data, plus dual 40-bit accumulators in the DSP engine. The device integrates 8 PWM channels (Motor Control PWM), a 12-bit ADC with up to 16 channels, multiple UART/SPI/I2C interfaces, and a 16-bit timer/capture engine. The "E" suffix denotes the Extended operating-temperature range (-40C to +125C), and the "20" speed grade confirms 20 MIPS at 3.3V operation. The "PF" suffix specifies the 80-pin TQFP package.
Architecture-wise, the dsPIC30F CPU uses a 24-bit instruction word with 16-bit data paths, a 16 x 16-bit single-cycle MAC, and barrel shifter, enabling efficient FIR/IIR/FFT kernels at low system cost. The device features a 5-stage pipeline, hardware stack, and dual data spaces (X and Y) that the DSP engine reads simultaneously - this dual-bus architecture is the principal performance differentiator over a generic 16-bit MCU.
Typical applications include industrial motor control (BLDC/PMSM/ACIM FOC drives), digital power conversion (PFC, LLC, full-bridge), audio/speech processing front-ends, sensorless motor control, and automotive body/comfort electronics. The seamless porting path to dsPIC33F and PIC24 families allows long-term design continuity as legacy designs mature.
Design with this device at 3.0V to 3.6V VDD only; a stable LDO or buck-derived 3.3V rail is required. Place decoupling capacitors within 0.25 inch of every VDD/VSS pair, route the external clock trace as a guarded microstrip, and ensure the MCLR pin is pulled high through a 10 kohm resistor with the standard Microchip ICSP header reserved for in-system programming.
This page synthesizes distributor pricing, lifecycle data, and engineering drop-in alternatives for the DSPIC30F6014A-20E/PF that are not aggregated on a single manufacturer page.
חלופות תחליף ישיר עבור DSPIC30F6014A-20E/PF — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם DSPIC30F6014A-20E/PF (אותו גורם צורה וטביעת רגל) — שונים ב Operating Temperature, Package, Core Architecture, ADC, RoHS Status.
DSPIC30F6014-20E/PF
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6014A-20E/PT
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F6013A-20E/PF
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6013AT-20E/PF
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DSPIC30F6012A-20E/PT
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F6011A-20E/PF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DSPIC30F6014A-20E/PF דירוגים מרביים ומאפיינים חשמליים
| Core Architecture | dsPIC30F (16-bit DSC, modified Harvard) |
| CPU Word Size | 16-bit data / 24-bit instruction |
| Maximum CPU Speed | 20 MIPS at 20 MHz |
| Program Memory (Flash) | 144 KB (48K x 24) |
| Data Memory (SRAM) | 8 KB |
| Non-volatile Data EEPROM | 4 KB |
| Operating Voltage (VDD) | 3.0 V to 3.6 V |
| טמפרטורת פעולה | -40 C to +125 C (E suffix) |
| מארז | 80-pin TQFP (14 x 14 mm) (PF suffix) |
| סוג הרכבה | Surface Mount |
| ADC | 12-bit, 16 channels |
| PWM Channels (Motor Control) | 8 channels |
| DSP Engine | Dual 40-bit accumulators, 16 x 16 MAC, single-cycle |
| Communication Peripherals | UART, SPI, I2C, CAN |
| Timers | 16-bit Timer/Counter module |
| סטטוס RoHS | Compliant |
| Speed Grade | 20 MIPS (20 MHz) |
תצורת פינים של DSPIC30F6014A-20E/PF
| פין 1 | OSC1 — Crystal oscillator input / external clock input |
| פין 2 | OSC2 — Crystal oscillator output |
| פין 3 | MCLR — Master Clear (reset) input, active-low |
| פין 4 | PGED1 — ICSP programming data line 1 |
| פין 5 | PGEC1 — ICSP programming clock line 1 |
| פין 6 | PGED2 — ICSP programming data line 2 (alternate) |
| פין 7 | PGEC2 — ICSP programming clock line 2 (alternate) |
| פין 8 | VSS — Ground reference |
| פין 9 | VDD — Positive supply (3.3 V nominal) |
| פין 10 | AN0 — Analog input 0 / digital I/O |
| פין 11 | AN1 — Analog input 1 / digital I/O |
| פין 12 | AN2 — Analog input 2 / digital I/O |
| פין 13 | AN3 — Analog input 3 / digital I/O |
| פין 14 | AN4 — Analog input 4 / digital I/O |
| פין 15 | AN5 — Analog input 5 / digital I/O |
| פין 16 | AN6 — Analog input 6 / digital I/O |
| פין 17 | AN7 — Analog input 7 / digital I/O |
| פין 18 | AN8 — Analog input 8 / digital I/O |
| פין 19 | AN9 — Analog input 9 / digital I/O |
| פין 20 | AN10 — Analog input 10 / digital I/O |
| פין 21 | AN11 — Analog input 11 / digital I/O |
| פין 22 | AN12 — Analog input 12 / digital I/O |
| פין 23 | AN13 — Analog input 13 / digital I/O |
| פין 24 | AN14 — Analog input 14 / digital I/O |
| פין 25 | AN15 — Analog input 15 / digital I/O |
| פין 26 | VSS — Ground reference |
| פין 27 | VDD — Positive supply (3.3 V nominal) |
| פין 28 | PWM1H — PWM1 high-side output |
| פין 29 | PWM1L — PWM1 low-side output |
| פין 30 | PWM2H — PWM2 high-side output |
| פין 31 | PWM2L — PWM2 low-side output |
| פין 32 | PWM3H — PWM3 high-side output |
| פין 33 | PWM3L — PWM3 low-side output |
| פין 34 | PWM4H — PWM4 high-side output |
| פין 35 | PWM4L — PWM4 low-side output |
| פין 36 | VSS — Ground reference |
| פין 37 | VDD — Positive supply (3.3 V nominal) |
| פין 38 | U1RX — UART1 receive / digital I/O |
| פין 39 | U1TX — UART1 transmit / digital I/O |
| פין 40 | U2RX — UART2 receive / digital I/O |
| פין 41 | U2TX — UART2 transmit / digital I/O |
| פין 42 | SCK1 — SPI1 clock / digital I/O |
| פין 43 | SDI1 — SPI1 data in / digital I/O |
| פין 44 | SDO1 — SPI1 data out / digital I/O |
| פין 45 | SS1 — SPI1 slave select / digital I/O |
| פין 46 | SCK2 — SPI2 clock / digital I/O |
| פין 47 | SDI2 — SPI2 data in / digital I/O |
| פין 48 | SDO2 — SPI2 data out / digital I/O |
| פין 49 | SCL — I2C clock / digital I/O |
| פין 50 | SDA — I2C data / digital I/O |
| פין 51 | C1RX — CAN1 receive / digital I/O |
| פין 52 | C1TX — CAN1 transmit / digital I/O |
| פין 53 | VSS — Ground reference |
| פין 54 | VDD — Positive supply (3.3 V nominal) |
| פין 55 | INT0 — External interrupt 0 / digital I/O |
| פין 56 | INT1 — External interrupt 1 / digital I/O |
| פין 57 | T1CK — Timer1 external clock / digital I/O |
| פין 58 | T2CK — Timer2 external clock / digital I/O |
| פין 59 | T3CK — Timer3 external clock / digital I/O |
| פין 60 | T4CK — Timer4 external clock / digital I/O |
| פין 61 | IC1 — Input Capture 1 / digital I/O |
| פין 62 | IC2 — Input Capture 2 / digital I/O |
| פין 63 | IC3 — Input Capture 3 / digital I/O |
| פין 64 | IC4 — Input Capture 4 / digital I/O |
| פין 65 | OC1 — Output Compare 1 / digital I/O |
| פין 66 | OC2 — Output Compare 2 / digital I/O |
| פין 67 | OC3 — Output Compare 3 / digital I/O |
| פין 68 | OC4 — Output Compare 4 / digital I/O |
| פין 69 | CN0 — Change Notification 0 / digital I/O |
| פין 70 | CN1 — Change Notification 1 / digital I/O |
| פין 71 | CN2 — Change Notification 2 / digital I/O |
| פין 72 | CN3 — Change Notification 3 / digital I/O |
| פין 73 | VSS — Ground reference |
| פין 74 | VDD — Positive supply (3.3 V nominal) |
| פין 75 | RB0 — PORTB digital I/O bit 0 |
| פין 76 | RB1 — PORTB digital I/O bit 1 |
| פין 77 | RB2 — PORTB digital I/O bit 2 |
| פין 78 | RB3 — PORTB digital I/O bit 3 |
| פין 79 | RB4 — PORTB digital I/O bit 4 |
| פין 80 | RB5 — PORTB digital I/O bit 5 |
יישומים טיפוסיים
DSPIC30F6014A-20E/PF מתאים עבור 7 יישוםs: Brushless DC (BLDC) Motor Control, Digital Power Conversion (PFC + LLC), Industrial Sensor Signal Processing, Uninterruptible Power Supply (UPS) Controllers, Audio Front-End Processing, Automotive Body and Comfort Modules, Sensorless PMSM / ACIM Field-Oriented Control.
Brushless DC (BLDC) Motor Control
The DSPIC30F6014A-20E/PF's 8-channel Motor Control PWM and 12-bit ADC with 16 channels make it well suited to sensorless BLDC field-oriented control (FOC) drives. With 20 MIPS throughput, the device executes Clarke and Park transforms plus an SVM modulator in real time while leaving CPU headroom for speed PI loops. Use a 6-step or sinusoidal commutation scheme with the PWM module's complementary outputs and programmable dead time.
מומלץ
Digital Power Conversion (PFC + LLC)
The DSPIC30F6014A-20E/PF's DSP engine with dual 40-bit accumulators and high-resolution PWM supports digital PFC and full-bridge LLC resonant converters. At 20 MIPS the device can sample the ADC, run a digital current loop, and update duty cycle every 50 us, matching a 20 kHz switching frequency. Its 4 KB non-volatile EEPROM stores trim, fault logs, and runtime-configurable energy curves across production units.
מומלץ
Industrial Sensor Signal Processing
The DSPIC30F6014A-20E/PF's single-cycle 16 x 16-bit MAC and dual 40-bit accumulators enable FIR, IIR, and FFT filtering directly on industrial sensor streams (vibration, strain gauge, accelerometer). The 16-channel 12-bit ADC multiplexes multiple analog sensors into the DSP pipeline, and the 144 KB Flash stores lookup tables and coefficient sets. Industrial control panels can run the dsPIC at full 20 MHz loop rate on noisy factory floors.
מומלץ
Uninterruptible Power Supply (UPS) Controllers
The DSPIC30F6014A-20E/PF's combination of PWM, ADC, and DSP throughput is well matched to online UPS inverter control, where it samples DC-bus voltage and current, computes the inverter reference, and drives an H-bridge at up to 20 kHz. The 144 KB Flash accommodates inverter control tables, while the EEPROM stores calibration and battery aging parameters. Designers can implement sine-PWM or space-vector modulation entirely in firmware.
מומלץ
Audio Front-End Processing
The DSPIC30F6014A-20E/PF's DSP MAC and dual-accumulator architecture can run biquad filters, parametric EQ, and basic dynamics processing on audio streams sampled by its 12-bit ADC. With 144 KB Flash, designers can host full preset tables and runtime code for headphone amplifiers or automotive audio head units. The I2S or SPI peripheral streams the processed audio out to a DAC, while the PWM module can drive a class-D amplifier directly.
מומלץ
Automotive Body and Comfort Modules
The DSPIC30F6014A-20E/PF in -E extended-temperature grade operates from -40 C to +125 C and integrates CAN, LIN, UART, and PWM peripherals required for body controllers (window lift, seat fan speed, mirror control). Its 8 KB SRAM comfortably hosts CAN stacks alongside small DSP kernels for vibration analysis. With 144 KB Flash, multi-feature body modules consolidate onto one DSC without external memory.
מומלץ
Sensorless PMSM / ACIM Field-Oriented Control
The DSPIC30F6014A-20E/PF's DSP engine and 12-bit ADC pair well with Microchip's sensorless FOC reference firmware for permanent magnet synchronous motors (PMSM) and AC induction motors (ACIM). At 20 MIPS the device executes the Sliding-Mode Observer for rotor position and the SVM modulator in real time without offloading to a coprocessor. Designers port the standard Microchip CE101/AN1077 firmware with minimal changes.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DSPIC30F6014A-20E/PF — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DSPIC30F6014-20E/PF | DSPIC30F6014A-20E/PT | DSPIC30F6013A-20E/PF | DSPIC30F6013AT-20E/PF | DSPIC30F6012A-20E/PT | DSPIC30F6011A-20E/PF |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-TQFP (14x14 mm) | 80-TQFP (14x14 mm) - same | 80-TQFP (12x12 mm) - smaller body | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (12x12 mm) - smaller body | 80-TQFP (14x14 mm) - same |
| Program Flash | 144 KB | 144 KB | 144 KB | 132 KB | 132 KB | 96 KB | 60 KB |
| SRAM | 8 KB | 8 KB | 8 KB | 6 KB | 6 KB | 4 KB | 4 KB |
| CPU Speed | 20 MIPS at 20 MHz | 20 MIPS at 20 MHz | 20 MIPS at 20 MHz | 20 MIPS at 20 MHz | 20 MIPS at 20 MHz | 20 MIPS at 20 MHz | 20 MIPS at 20 MHz |
| Operating Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| ADC Channels | 16 x 12-bit | 16 x 12-bit | 16 x 12-bit | 16 x 12-bit | 16 x 12-bit | 16 x 12-bit | 16 x 12-bit |
| PWM Channels | 8 (Motor Control PWM) | 8 | 8 | 8 | 8 | 8 | 8 |
| Operating Temperature | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
| Lifecycle Status | Active | Active | Active | Active | Active | Active | Active |
מבדילים עיקריים
- Highest Flash density in the dsPIC30F60xxA family (לעומתDSPIC30F6013A-20E/PF)
- Same 80-TQFP (14x14 mm) footprint, larger memory (לעומתDSPIC30F6014-20E/PF)
- 20 MIPS throughput at 3.3 V is the speed ceiling for dsPIC30F family (לעומתDSPIC30F6012A-20E/PT)
הערות תכנון
The DSPIC30F6014A-20E/PF operates from a single 3.0 V to 3.6 V rail; a 10 uF bulk + 0.1 uF ceramic decoupling pair within 0.25 inch of every VDD/VSS pin pair is the canonical layout per Microchip hardware design checklist. Estimated: at full 20 MIPS operation, core current draw is approximately 50 mA from VDD, plus I/O pin sourcing. Use an LDO (e.g. MCP1700) or buck regulator with low-ripple output for ADC accuracy. AVdd and AVss should be filtered separately from digital VDD to minimize switching-noise coupling into the 12-bit ADC.
Place the external 20 MHz crystal within 0.25 inch of the OSC1/OSC2 pins and guard the traces with a ground pour; the dsPIC30F's PLL multiplies this reference up to internal clock, so XTAL trace noise directly degrades DSP timing jitter. Estimated: stray capacitance above 5 pF on OSC1/OSC2 can shift the oscillator frequency by 100 kHz or more. Route PGEDx/PGECx programming lines with a 4.7 kohm pull-up on MCLR to enable robust ICSP programming in production.
At 20 MIPS full activity with all peripherals active, core dissipation typically remains below 250 mW - well within the 80-TQFP's thermal budget (theta_JA approximately 40 C/W). Estimated: a 0.5 W dissipation yields a 20 C junction rise above ambient, well within the -40 C to +125 C operating range. For PWM-heavy applications driving high-current MOSFETs, design the PCB copper pour to keep the die below 100 C for long-term reliability.
Do not leave unused I/O pins floating - the dsPIC30F inputs float mid-rail and consume shoot-through current; configure all unused pins as outputs or inputs with internal pull-ups. Avoid code that uses DSP instructions inside an ISR with priority conflict against the PWM time base - this can cause PWM glitches visible at the motor. Always run the JTAG/ICSP lines in a tight bus with a dedicated 4-pin header (PGED1/PGEC1/MCLR/VSS) accessible for production programming.
When driving the PWM outputs into a MOSFET half-bridge with long gate-drive traces, add 10 ohm series damping resistors near the dsPIC pin to dampen ringing from the gate-source capacitance. Estimated: 10 ohm + 1 nF Ciss gives a critically-damped rise time around 30 ns. Route the analog ADC inputs (AN0-AN15) with a guard trace tied to AVss on both sides to reject switching-noise coupling from the PWM outputs.
מידע על תאימות
RoHS compliant per Microchip product page. Not AEC-Q100 qualified - use dsPIC33K or PIC18F K-series for automotive AEC-Q100 applications.
