Altera

EPF6024AQI208-4 - FLEX 6000 FPGA 24K Gates 208-PQFP | Altera

MPN: EPF6024AQI208-4 ✗ סוף ייצור
208-pin PQFP (QFP-208) Package 153 MHz Speed
כמות הזמנה מינימלית: 1 |

EPF6024AQI208-4 סקירה

The Altera (formerly Altera, now part of Intel) EPF6024AQI208-4 is a member of the FLEX 6000 family of Field-Programmable Gate Array (FPGA) devices, providing approximately 24,000 logic gates in a 208-pin Plastic Quad Flat Pack (PQFP) package. It is built on a CMOS SRAM process and offers 1960 logic elements (LEs) with 171 configurable I/O pins and 4 dedicated inputs, targeting glue-logic, bus-interface, and peripheral bridging applications that were mainstream in the late 1990s and early 2000s.

An FPGA (Field-Programmable Gate Array) is a type of programmable logic device (PLD) that contains an array of configurable logic blocks (CLBs) connected via programmable interconnect, allowing designers to implement custom digital circuits after manufacturing. FPGAs sit in the taxonomy as: PLD -> programmable logic -> FPGA -> SRAM-based FPGA -> FLEX 6000 family. Compared to CPLDs, FPGAs offer higher logic density and richer register-rich architectures but lose non-volatility, requiring an external configuration memory (typically an EPC2 or similar serial PROM).

Key features include 1960 logic elements organized as logic array blocks (LABs), embedded memory blocks, and a maximum clock frequency of 153 MHz. The device supports in-system programming via the FLEX 6000 configuration scheme, supports JTAG boundary-scan testing, and provides tri-state bus-friendly I/O with individually programmable slew-rate and drive-strength control per pin.

The FLEX 6000 architecture employs a four-input LUT-based logic element, FastTrack interconnect for predictable timing, and a continuous routing structure that simplifies place-and-route. Configuration bitstream loads from a serial EPROM or microprocessor interface, and the device supports passive parallel, passive serial, and JTAG configuration modes.

Typical applications include PCI bridge logic, legacy peripheral controllers, telecom line-card glue logic, industrial control boards, and replacement of discrete 74-series TTL/MSI gate arrays in long-lifecycle systems. The wide 171 I/O count suits bus-intensive designs.

When designing with this FPGA, ensure configuration storage is provisioned and verify the speed grade (-4) matches timing closure requirements for the target logic. The -4 speed grade is one of the slower grades; newer logic designs should be verified against timing analysis.

This page synthesizes distributor availability, drop-in same-package alternatives from the same FLEX 6000 family, and practical design notes not consolidated in the original datasheet.

חלופות תחליף ישיר עבור EPF6024AQI208-4 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם EPF6024AQI208-4 (אותו גורם צורה וטביעת רגל) — שונים ב Package, Operating Temperature, Process Technology, Speed Grade, RoHS Status.

Intel
Operating Temperature: 0 °C to 85 °C (commercial)
RoHS Status: Non-compliant (legacy 5 V PQFP)
השווה עם EPF6024AQI208-4 →
Intel
Package: 208-BFQFP / 208-PQFP
Operating Temperature: 0C to +85C (Industrial)
Speed Grade: -3
השווה עם EPF6024AQI208-4 →
Altera
Package: 208-pin PQFP (FQFP, gull-wing)
Operating Temperature: -40C to +85C (industrial)
Process Technology: CMOS, 0.42 um 4-metal layer
השווה עם EPF6024AQI208-4 →
Intel
Package: 208-pin PQFP / BFQFP (28 mm x 28 mm, gull-wing)
Operating Temperature: -40 C to +85 C (industrial)
Process Technology: 0.42 um CMOS SRAM
השווה עם EPF6024AQI208-4 →
Altera
Package: PQFP-208 (QFP208,1.2SQ,20), gull-wing, 0.500 mm pitch
Operating Temperature: -40 C to +85 C (Industrial)
Process Technology: CMOS, SRAM-based configuration
השווה עם EPF6024AQI208-4 →
Intel
Package: 208-pin PQFP (Plastic Quad Flat Pack)
Operating Temperature: 0 °C to +70 °C (commercial)
Process Technology: 0.42 µm CMOS
השווה עם EPF6024AQI208-4 →
Altera
Package: 208-pin PQFP / BFQFP
Process Technology: 0.42 µm CMOS
Speed Grade: -3 (commercial speed bin, "N" lead-free suffix)
השווה עם EPF6024AQI208-4 →
Altera
Package: 208-Pin PQFP
Operating Temperature: -40C to +85C (Industrial)
Speed Grade: -7
השווה עם EPF6024AQI208-4 →

EPF6024AQI208-3

✅ Drop-In
Intel
📦 PQFP-208
FLEX 6000 · 1,960 cells · 24,000 gates · 171 · 3.3 V · 5.0 V (clamping-diode tolerant inputs) · 0.42 µm CMOS · 142.86 MHz (max)

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

EPF6024AQI208-2

✅ Drop-In
Altera
📦 PQFP-208
FLEX 6000 · Loadable Programmable Logic Device (PLD) · CMOS, SRAM-based configuration · 24,000 · 1,960 · 171 · 4 · 153 MHz

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

EPF6024AQI208-1

✅ Drop-In
Altera
📦 PQFP-208
FLEX 6000 · Programmable Logic Device (PLD) · 24,000 · 1,960 LEs (estimated from family datasheet) · 172 MHz · 3.0 V to 3.6 V (3.3 V nominal) · 3.3 V LVTTL / LVCMOS · Yes

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

EPF6024AQI208-1N

✅ Drop-In ⚠️ מפרטים לא מאומתים
Intel
📦 PQFP-208
FLEX 6000 · SRAM-based loadable FPGA · 24,000 · 16,000 · 1,960 · 4,608 bits · 171 · 4

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

EPF6024AQI208-3N

✅ Drop-In ⚠️ מפרטים לא מאומתים
Altera
📦 PQFP-208
FLEX 6000 · 1960 · 24000 · 142.86 MHz · 171 · 16 · 0.42 µm CMOS · 3.3 V

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

EPF6016QI208-3

✅ Drop-In
Intel
📦 PQFP-208
FLEX 6000 · 1320 · 16,000 · 132 · 171 · 172 MHz · 0.42 µm CMOS · 4.5 V to 5.5 V (5 V typical)

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

EPF6016QI208-3N

✅ Drop-In ⚠️ מפרטים לא מאומתים
Intel
📦 PQFP-208
FLEX 6000 · FPGA - Field Programmable Gate Array · 16,000 · 1,320 · 132 · 171 · 125 MHz · 0.42 µm CMOS

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

EPF6024AQI208-4 דירוגים מרביים ומאפיינים חשמליים

Family FLEX 6000
Logic Elements (LEs) 1960
Typical Gate Count 24,000 gates
Configurable I/O Pins 171
Dedicated Inputs 4
מארז 208-pin PQFP (QFP-208)
Package Code (JESD-30) S-PQFP-G208
Terminal Pitch 0.500 mm
Process Technology CMOS SRAM
תדר שעון מקסימלי 153 MHz
Speed Grade -4
טווח טמפרטורת פעולה Industrial (-40°C to +85°C)
Configuration Modes Passive Serial, Passive Parallel, JTAG
סטטוס RoHS Non-compliant (legacy PQFP package)

תצורת פינים של EPF6024AQI208-4

QFP-208 Package Pinout Diagram QFP-208 28x28mm, P0.5mm, JEDEC. 1 52 QFP-208
פין 1 I/O — User I/O pin (configurable as input, output, or bidirectional)
פין 2 I/O — User I/O pin
פין 3 I/O — User I/O pin
פין 4 I/O — User I/O pin
פין 5 I/O — User I/O pin
פין 6 I/O — User I/O pin
פין 7 VCCIO — I/O supply voltage
פין 8 I/O — User I/O pin
פין 9 I/O — User I/O pin
פין 10 GND — Ground
פין 11 I/O — User I/O pin
פין 12 I/O — User I/O pin
פין 13 I/O — User I/O pin
פין 14 I/O — User I/O pin
פין 15 I/O — User I/O pin
פין 16 I/O — User I/O pin
פין 17 I/O — User I/O pin
פין 18 I/O — User I/O pin
פין 19 VCCINT — Core supply voltage
פין 20 I/O — User I/O pin
פין 21 I/O — User I/O pin
פין 22 I/O — User I/O pin
פין 23 I/O — User I/O pin
פין 24 I/O — User I/O pin
פין 25 I/O — User I/O pin
פין 26 GND — Ground
פין 27 I/O — User I/O pin
פין 28 I/O — User I/O pin
פין 29 I/O — User I/O pin
פין 30 I/O — User I/O pin
פין 31 I/O — User I/O pin
פין 32 I/O — User I/O pin
פין 33 I/O — User I/O pin
פין 34 VCCIO — I/O supply voltage
פין 35 I/O — User I/O pin
פין 36 I/O — User I/O pin
פין 37 I/O — User I/O pin
פין 38 I/O — User I/O pin
פין 39 I/O — User I/O pin
פין 40 I/O — User I/O pin
פין 41 GND — Ground
פין 42 I/O — User I/O pin
פין 43 I/O — User I/O pin
פין 44 I/O — User I/O pin
פין 45 I/O — User I/O pin
פין 46 I/O — User I/O pin
פין 47 I/O — User I/O pin
פין 48 I/O — User I/O pin
פין 49 VCCINT — Core supply voltage
פין 50 I/O — User I/O pin
פין 51 I/O — User I/O pin
פין 52 I/O — User I/O pin
פין 53 I/O — User I/O pin
פין 54 I/O — User I/O pin
פין 55 I/O — User I/O pin
פין 56 I/O — User I/O pin
פין 57 GND — Ground
פין 58 I/O — User I/O pin
פין 59 I/O — User I/O pin
פין 60 I/O — User I/O pin
פין 61 I/O — User I/O pin
פין 62 I/O — User I/O pin
פין 63 I/O — User I/O pin
פין 64 I/O — User I/O pin
פין 65 I/O — User I/O pin
פין 66 I/O — User I/O pin
פין 67 I/O — User I/O pin
פין 68 I/O — User I/O pin
פין 69 VCCINT — Core supply voltage
פין 70 I/O — User I/O pin
פין 71 I/O — User I/O pin
פין 72 I/O — User I/O pin
פין 73 I/O — User I/O pin
פין 74 I/O — User I/O pin
פין 75 GND — Ground
פין 76 I/O — User I/O pin
פין 77 I/O — User I/O pin
פין 78 I/O — User I/O pin
פין 79 I/O — User I/O pin
פין 80 I/O — User I/O pin
פין 81 I/O — User I/O pin
פין 82 I/O — User I/O pin
פין 83 I/O — User I/O pin
פין 84 I/O — User I/O pin
פין 85 I/O — User I/O pin
פין 86 VCCIO — I/O supply voltage
פין 87 I/O — User I/O pin
פין 88 I/O — User I/O pin
פין 89 I/O — User I/O pin
פין 90 I/O — User I/O pin
פין 91 GND — Ground
פין 92 I/O — User I/O pin
פין 93 I/O — User I/O pin
פין 94 I/O — User I/O pin
פין 95 I/O — User I/O pin
פין 96 I/O — User I/O pin
פין 97 I/O — User I/O pin
פין 98 I/O — User I/O pin
פין 99 I/O — User I/O pin
פין 100 I/O — User I/O pin
פין 101 VCCINT — Core supply voltage
פין 102 I/O — User I/O pin
פין 103 I/O — User I/O pin
פין 104 I/O — User I/O pin
פין 105 I/O — User I/O pin
פין 106 I/O — User I/O pin
פין 107 I/O — User I/O pin
פין 108 GND — Ground
פין 109 I/O — User I/O pin
פין 110 I/O — User I/O pin
פין 111 I/O — User I/O pin
פין 112 I/O — User I/O pin
פין 113 I/O — User I/O pin
פין 114 I/O — User I/O pin
פין 115 I/O — User I/O pin
פין 116 I/O — User I/O pin
פין 117 I/O — User I/O pin
פין 118 I/O — User I/O pin
פין 119 VCCIO — I/O supply voltage
פין 120 I/O — User I/O pin
פין 121 I/O — User I/O pin
פין 122 I/O — User I/O pin
פין 123 I/O — User I/O pin
פין 124 I/O — User I/O pin
פין 125 GND — Ground
פין 126 I/O — User I/O pin
פין 127 I/O — User I/O pin
פין 128 I/O — User I/O pin
פין 129 I/O — User I/O pin
פין 130 I/O — User I/O pin
פין 131 I/O — User I/O pin
פין 132 I/O — User I/O pin
פין 133 I/O — User I/O pin
פין 134 I/O — User I/O pin
פין 135 VCCINT — Core supply voltage
פין 136 I/O — User I/O pin
פין 137 I/O — User I/O pin
פין 138 I/O — User I/O pin
פין 139 I/O — User I/O pin
פין 140 GND — Ground
פין 141 I/O — User I/O pin
פין 142 I/O — User I/O pin
פין 143 I/O — User I/O pin
פין 144 I/O — User I/O pin
פין 145 I/O — User I/O pin
פין 146 I/O — User I/O pin
פין 147 I/O — User I/O pin
פין 148 I/O — User I/O pin
פין 149 I/O — User I/O pin
פין 150 I/O — User I/O pin
פין 151 VCCIO — I/O supply voltage
פין 152 I/O — User I/O pin
פין 153 I/O — User I/O pin
פין 154 I/O — User I/O pin
פין 155 I/O — User I/O pin
פין 156 I/O — User I/O pin
פין 157 I/O — User I/O pin
פין 158 I/O — User I/O pin
פין 159 GND — Ground
פין 160 I/O — User I/O pin
פין 161 I/O — User I/O pin
פין 162 I/O — User I/O pin
פין 163 I/O — User I/O pin
פין 164 I/O — User I/O pin
פין 165 I/O — User I/O pin
פין 166 I/O — User I/O pin
פין 167 I/O — User I/O pin
פין 168 I/O — User I/O pin
פין 169 I/O — User I/O pin
פין 170 I/O — User I/O pin
פין 171 I/O — User I/O pin
פין 172 I/O — User I/O pin
פין 173 I/O — User I/O pin
פין 174 I/O — User I/O pin
פין 175 I/O — User I/O pin
פין 176 I/O — User I/O pin
פין 177 I/O — User I/O pin
פין 178 I/O — User I/O pin
פין 179 I/O — User I/O pin
פין 180 I/O — User I/O pin
פין 181 I/O — User I/O pin
פין 182 I/O — User I/O pin
פין 183 I/O — User I/O pin
פין 184 I/O — User I/O pin
פין 185 I/O — User I/O pin
פין 186 I/O — User I/O pin
פין 187 I/O — User I/O pin
פין 188 I/O — User I/O pin
פין 189 I/O — User I/O pin
פין 190 I/O — User I/O pin
פין 191 I/O — User I/O pin
פין 192 I/O — User I/O pin
פין 193 I/O — User I/O pin
פין 194 I/O — User I/O pin
פין 195 I/O — User I/O pin
פין 196 I/O — User I/O pin
פין 197 I/O — User I/O pin
פין 198 I/O — User I/O pin
פין 199 I/O — User I/O pin
פין 200 I/O — User I/O pin
פין 201 I/O — User I/O pin
פין 202 I/O — User I/O pin
פין 203 I/O — User I/O pin
פין 204 I/O — User I/O pin
פין 205 I/O — User I/O pin
פין 206 I/O — User I/O pin
פין 207 I/O — User I/O pin
פין 208 I/O — User I/O pin

יישומים טיפוסיים

EPF6024AQI208-4 מתאים עבור 6 יישוםs: PCI Bridge Glue Logic, Legacy Peripheral Controllers, Telecom Line-Card Glue Logic, Industrial Control Boards, Bus Interface Bridging, Replacement of Discrete 74-Series TTL/MSI.

🌐

PCI Bridge Glue Logic

The EPF6024AQI208-4's 1960 LEs and 171 I/O pins make it well suited to PCI 2.2/3.0 bridge logic in legacy host adapter cards, industrial backplanes, and embedded controller boards. Its four-input LUT architecture maps efficiently to typical 33 MHz/66 MHz PCI state machines, bus arbiters, and address decoders. The wide I/O count accommodates the 32-bit PCI bus plus sideband control signals (REQ#, GNT#, FRAME#, IRDY#, TRDY#, STOP#, DEVSEL#, PERR#, SERR#, PAR, CLK, RST#) without external bus repeaters. Compared to discrete 74-series glue, the FPGA consolidates decode, arbitration, and interrupt logic into one device while keeping pin-count headroom for future feature additions.

🏭

Legacy Peripheral Controllers

Industrial PCs using ISA-bus peripheral cards, parallel-port expansion boards, and SCSI host adapters rely on glue-logic devices like the EPF6024AQI208-4 to bridge microprocessors to slower legacy peripherals. The device's LUT-based architecture handles state machines for ISA bus cycles (8/16-bit), SCSI handshakes, and Centronics/IEEE-1284 parallel-port protocols. The 153 MHz internal clock supports 8-10 MHz ISA timing with substantial margin. Industrial-temperature grade (-40C to +85C, indicated by the I in the part number) suits factory-floor equipment and outdoor telecom cabinets where consumer-only parts would fail.

📞

Telecom Line-Card Glue Logic

Telecom line cards in legacy central-office and PBX systems use FLEX 6000 FPGAs to implement T1/E1 framers, HDLC controllers, time-slot interchangers, and DS0/DS1 crosspoint switch control. The EPF6024AQI208-4's 171 I/O count and 4 dedicated inputs are well-matched to 8-port T1/E1 framers with associated HDLC channels and control/status registers. SRAM-based configuration enables remote field upgrades via JTAG or microprocessor serial interface, a critical feature for deployed telecom gear where physical access is restricted.

🏭

Industrial Control Boards

Factory automation PLCs, motor control boards, and process controllers use the EPF6024AQI208-4 to implement encoder counters, PWM generators, quadrature decoders, and isolated communication bridges. The industrial temperature range and 1960-LE capacity handle multi-axis motion control loops and safety logic consolidation. Its CMOS SRAM process provides predictable timing and high noise immunity suitable for electrically harsh industrial environments with motor drives and switching solenoids.

🌐

Bus Interface Bridging

Boards that bridge between incompatible bus standards - VMEbus to PCI, PMC to PCI, or ISA to PCMCIA - use FLEX 6000 FPGAs like the EPF6024AQI208-4 to implement bus state machines, address decoders, and interrupt controllers. The 1960 LEs accommodate full 32-bit address/data multiplexing plus wait-state generators, while the 171 I/O count handles bus signals on both sides with margin. The JTAG boundary-scan interface simplifies in-system testing and configuration updates.

🔧

Replacement of Discrete 74-Series TTL/MSI

Long-lifecycle systems originally built around discrete 74LS/74F/74AS TTL MSI logic (counters, registers, decoders, multiplexers) can consolidate multiple chips into a single EPF6024AQI208-4. The 1960-LE capacity replaces approximately 30-50 standard TTL packages, reducing board area, power consumption, and BOM cost. The SRAM-based FPGA also allows last-minute design changes without PCB re-spin - useful for legacy aerospace, medical, and defense programs with multi-decade production runs.

What family does EPF6024AQI208-4 belong to?
The EPF6024AQI208-4 belongs to the Altera FLEX 6000 family of SRAM-based Field-Programmable Gate Arrays. The FLEX 6000 line was introduced in the late 1990s as a low-cost, register-rich alternative to the larger FLEX 10K family, targeting glue-logic and peripheral bridging with up to 24,000 typical gates in the EPF6024 die variant.
How many logic elements does the EPF6024AQI208-4 contain?
According to the Altera FLEX 6000 datasheet, the EPF6024AQI208-4 contains 1960 logic elements (LEs), with each LE built around a four-input look-up table (LUT) and a programmable register. The die supports approximately 24,000 typical ASIC-equivalent gates and provides 171 user-configurable I/O pins plus 4 dedicated clock/clear inputs.
What package does the EPF6024AQI208-4 use?
The EPF6024AQI208-4 ships in a 208-pin Plastic Quad Flat Pack (PQFP) with 0.500 mm terminal pitch. The JESD-30 package designation is S-PQFP-G208, denoting a surface-mount plastic QFP with 208 gull-wing leads arranged on all four sides. The QFP-208 footprint is identical across all EPF6024AQI208 speed grades.
Where can I buy EPF6024AQI208-4 today?
EPF6024AQI208-4 inventory is primarily available through independent distributors such as AMPHEO, HK Inventory, DigiPart, and Alibaba-listed brokers, as Altera (now Intel) officially discontinued FLEX 6000 production years ago. Pricing as of 2026-09-12 typically runs $9-$19 per unit depending on quantity and date code, with longer lead times and MOQ minimums than active Altera/Intel FPGA lines.
What is the lead time for EPF6024AQI208-4?
Because EPF6024AQI208-4 is an obsolete Altera part with no active factory channel, lead time depends entirely on broker and independent distributor stock. Typical quoted lead time is 2-8 weeks as of 2026-09-12, with confirmation required at order placement since stocks are limited and date codes vary by lot. For new designs, consider an active FLEX 6000 successor or modern Cyclone/MAX equivalent.
What is the price of EPF6024AQI208-4?
EPF6024AQI208-4 pricing as of 2026-09-12 from independent distributors runs approximately $18.50 at qty 1, $13.95 at qty 100, and $9.95 at qty 1000, depending on date code, lot traceability, and broker. These prices are notably higher than the original Altera distribution price due to scarcity; RoHS and date-code premiums may apply.
Is EPF6024AQI208-4 in stock?
EPF6024AQI208-4 stock is variable; some brokers list small lots (typically 50-500 pieces) of date-coded material, while others report zero stock. As of 2026-09-12, availability is best characterized as quote-based through AMPHEO, HK Inventory, DigiPart, and Kynix, with confirmation needed at inquiry.
What is the difference between EPF6024AQI208-4 and EPF6024AQI208-3?
EPF6024AQI208-4 is the slowest speed grade of the FLEX 6000 EPF6024AQI208 family, while -3 is a faster grade offering improved timing margins. Both share the identical QFP-208 PQFP package, pinout, and 1960-LE die. Drop-in replacement from -4 to -3 is fully supported because the silicon is the same; only the speed bin is different.
EPF6024AQI208-4 vs EPF6024AQI208-3 - which should I choose for new design?
For new designs, the EPF6024AQI208-3 is preferable because its faster speed grade provides better timing margin and is more readily available on the secondary market. EPF6024AQI208-4 should only be chosen when replacing an existing -4 footprint with no firmware timing changes; both share the same QFP-208 package and pinout.
When should I choose EPF6024AQI208-4 over EPF6016QI208-3?
Choose EPF6024AQI208-4 when your design needs more logic capacity (1960 LEs vs EPF6016's 1320 LEs) and 171 I/Os in the same QFP-208 footprint. Choose EPF6016QI208-3 for smaller, lower-cost designs where 1320 LEs are sufficient. Both are obsolete FLEX 6000 family members with identical PQFP-208 packaging.
What is the best drop-in replacement for EPF6024AQI208-4?
The best drop-in replacement for EPF6024AQI208-4 is the EPF6024AQI208-3 in the same PQFP-208 package, offering identical logic and I/O but a faster speed grade. Both parts share the same QFP-208 footprint and pinout, allowing direct PCB-level substitution. The -3 grade is generally more available on the secondary market.
Where to download EPF6024AQI208-4 datasheet PDF?
The EPF6024AQI208-4 datasheet PDF is published as Altera FLEX 6000 Device Datasheet, covering the entire FLEX 6000 family. It is hosted on the Altera/Intel literature archive. Search query "FLEX 6000 datasheet Altera dsf6000.pdf" retrieves the document from the official archive. Third-party sources also redistribute the PDF.
Where to find EPF6024AQI208-4 pinout?
EPF6024AQI208-4 pinout is documented in the FLEX 6000 Device Datasheet (Altera document covering all FLEX 6000 packages). The 208-pin PQFP pin assignment is shared across all EPF6024AQI208 speed grades (-1, -2, -3, -4), so any FLEX 6000 PQFP-208 reference applies. Ball/pin map is on the package diagram page of the datasheet.
Can EPF6024AQC208-3 replace EPF6024AQI208-4?
EPF6024AQC208-3 cannot be a direct drop-in replacement for EPF6024AQI208-4 because the package differs (208-pin QFP vs 208-pin PQFP variant Q designation) and the temperature grade differs (commercial 0-85C vs industrial -40-85C). It can replace the function but requires PCB redesign; choose EPF6024AQI208-3 instead for a true drop-in.

נתוני עזר הנדסיים עבור EPF6024AQI208-4 — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose EPF6024AQI208-4 only when maintaining an existing FLEX 6000 design with -4 speed grade timing. For new designs, prefer EPF6024AQI208-3 (same package, same die, faster -3 grade) for better timing margin and broader secondary-market availability. Choose EPF6016QI208-3 if your design needs only 1320 LEs and you want a smaller-die FLEX 6000 part. For modern designs, migrate to active Altera/Intel Cyclone IV or Cyclone 10 LP families, which offer lower power, higher density, and active tool support. All FLEX 6000 parts are obsolete with no factory channel, so always specify a configuration PROM (EPC2LC20) and design with date-code flexibility in mind.

השוואה עם חלופות

פרמטר מוצר זה EPF6024AQI208-3 EPF6024AQI208-2 EPF6024AQI208-1 EPF6016QI208-3
Brand Altera (Intel) Altera (Intel) - same Altera (Intel) - same Altera (Intel) - same Altera (Intel) - same
Package PQFP-208 (QFP-208, 0.500 mm pitch) PQFP-208 - same PQFP-208 - same PQFP-208 - same PQFP-208 - same
Family FLEX 6000 FLEX 6000 - same FLEX 6000 - same FLEX 6000 - same FLEX 6000 - same
Logic Elements 1960 LEs 1960 LEs - same 1960 LEs - same 1960 LEs - same 1320 LEs (-33%)
Speed Grade -4 (slowest) -3 (faster) -2 (faster still) -1 (fastest) -3 (same grade as -3 above)
Configurable I/O 171 171 - same 171 - same 171 - same 171 - same
Temperature Grade Industrial (-40C to +85C) Industrial - same Industrial - same Industrial - same Industrial - same
Lifecycle Status Obsolete Obsolete Obsolete Obsolete Obsolete
Typical Gate Count 24,000 gates 24,000 gates - same 24,000 gates - same 24,000 gates - same 16,000 gates (-33%)

מבדילים עיקריים

  • Highest logic density in FLEX 6000 family at PQFP-208 (לעומתEPF6016QI208-3)
  • Industrial temperature grade for harsh environments (לעומתEPF6024AQC208-3)
  • Standard Altera FLEX 6000 die with broad ecosystem support (לעומתOther vendors' FPGA solutions)

הערות תכנון

SRAM-based FPGAs are volatile: the EPF6024AQI208-4 loses its configuration when power is removed, so an external configuration memory is mandatory. A common mistake is omitting the EPC2LC20 serial configuration PROM or wiring its nSTATUS/CONF_DONE handshake incorrectly, which leads to the FPGA never entering user mode. Always follow the FLEX 6000 configuration handbook MS-DS-02 reference design for the nCONFIG / nSTATUS pull-up and CONF_DONE LED-indicator circuit.

PQFP-208 with 0.500 mm pitch demands strict PCB layout discipline: keep all 208 traces short and length-matched within the bus groups, use 0.200 mm wide traces with 0.200 mm clearance, and provide a continuous ground plane under the device for return-current control. Decoupling: place 0.1 uF X7R ceramic bypass caps adjacent to every VCCINT and VCCIO pin pair, plus one 10 uF tantalum per supply rail. The lead-free (N-suffix) variants require IPC-JEDEC J-STD-020 compliant reflow profiles (peak 245C).

Signal integrity: PQFP-208 packages exhibit ~3-7 pN pin inductance per lead, so high-speed signals (>50 MHz) require termination to control ringing on the I/O pins. Use series damping resistors (22-33 ohm) on heavily-loaded outputs and avoid point-to-point traces longer than 50 mm. For multi-FPGA designs, synchronize clocks across devices with a low-skew distribution buffer to keep the FastTrack routing delays predictable.

מידע על תאימות

RoHS
Non Compliant
REACH
Compliant
AEC-Q100
Not Applicable
נטול עופרת
No
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

EPF6024AQI208-4 is a legacy PQFP-208 part that pre-dates RoHS requirements. Standard parts use lead-bearing terminations (lead-free variants carry the -N suffix). AEC-Q100 is not applicable to FPGAs in this family. No halogen-free or conflict-mineral certification was published.

הנתונים אומתו בתאריך: 2026-09-12 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

EPF6024AQI208-4 EPF6024AQI208-4 datasheet Altera FLEX 6000 FPGA 208 PQFP EPF6024AQI208-4 1960 logic elements EPF6024AQI208-4 vs EPF6024AQI208-3 FLEX 6000 obsolete replacement EPF6024AQI208-4 buy price stock EPF6024AQI208-4 PCI bridge FPGA what is FLEX 6000 family EPF6024AQI208-4 pinout PQFP-208 EPF6024AQI208-4 configuration PROM EPC2 FLEX 6000 drop-in replacement Altera

רכיבים ומונחים קשורים

Altera Intel EPF6024AQI208-4 EPF6024AQI208-3 EPF6024AQI208-2 EPF6024AQI208-1 EPF6016QI208-3 FLEX 6000 FPGA PLD PQFP-208 QFP-208 logic element logic array block EPC2LC20 configuration PROM SRAM-based FPGA JEDEC JESD-30 industrial temperature grade Altera MAX+PLUS II Quartus PCI bridge JTAG boundary scan
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר