LM358DR2 - Dual 3-32V Op Amp | onsemi | Industrial
MPN: LM358DR2 ✓ פעילLM358DR2 סקירה
An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare two input voltages. The LM358 family combines two amplifiers in one package, reducing board area compared with two separate single amplifier packages. A low-dropout single-supply architecture allows the amplifier to operate from a supply only slightly above the required output range, while the common-mode input range extending toward ground supports sensors whose signals begin near 0 V.
The principal application advantages are the dual-channel configuration, 3 V to 32 V supply range, low power drain, and flexible single- or split-supply use. Two independent amplifier channels can implement non-inverting or inverting gain stages, differential sensing, comparators, active filters, transimpedance stages, and feedback loops. The 8-pin SOIC package supports compact PCB layouts and automated assembly, but the exposed package lead geometry and electrical limits must still be checked against the circuit requirements.
The LM358 architecture is intended for general-purpose analog signal conditioning rather than high-speed, precision, or rail-to-rail applications. Designers should account for input bias current, input offset voltage, output-current capability, common-mode limits, and output-swing behavior in each operating condition. Because no complete timing, noise, accuracy, or output-drive table appears in the product results, those values should be taken directly from the manufacturer data sheet before sizing external resistors or capacitors.
Typical uses include conditioning a 0 V to sensor-range signal, buffering a potentiometer, amplifying strain-gauge or thermocouple outputs, driving analog control loops, and forming active filters. In industrial systems, the 32 V maximum listed supply voltage provides compatibility with higher-voltage rails, but the design still requires correct input and output common-mode ranges for each channel.
The main layout consideration is decoupling. Place the supply bypass capacitor close to the positive supply and ground pins, keep feedback-loop routing short, and return analog-ground currents directly to the device ground rather than through high-current switching paths. Check bias-current-induced offset and output-swing limits before using the amplifier with high-impedance sources, and verify that the selected SOIC footprint matches the exact ordering code.
This product record combines the verified LM358DR2 identity, supply-range description, package information, sourcing links, drop-in comparison, and practical design guidance. It is intended to help engineers identify the correct dual amplifier and assess PCB, layout, and application compatibility before releasing a schematic or BOM.
חלופות תחליף ישיר עבור LM358DR2 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM358DR2 (אותו גורם צורה וטביעת רגל) — שונים ב Amplifier Type, Common-Mode Input Range, Number of Channels, Package.
LM2904DR
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TP358
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
SGMI8358
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
BP358
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
NSMOP-358
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LM358DR2 דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Dual operational amplifier |
| Number of Channels | 2 channels |
| Single-Supply Operating Voltage | 3 V to 32 V |
| Supply Configuration | Single supply or split supply |
| Common-Mode Input Range | Extends to ground and VEE |
| מארז | 8-pin SOIC |
| סוג הרכבה | Surface mount |
| Power Drain | Low |
מדריך תצורת פינים של LM358DR2 8-pin soic
תצורת פינים עבור LM358DR2 (מארזת 8-pin soic). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור LM358DR2.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LM358DR2 מתאים עבור 6 יישוםs: Low-Side Sensor Signal Conditioning, Industrial Control Feedback, Active Audio and Communication Filtering, Potentiometer and Resistive Sensor Buffering, Power-Supply Feedback and Monitoring, Portable Measurement and IoT Interfaces.
Low-Side Sensor Signal Conditioning
The LM358DR2 fits low-side sensor conditioning because its common-mode input range extends to ground and VEE, allowing signals near 0 V to be processed from a 3 V to 32 V supply. Use one channel to amplify the sensor output and the second for buffering, gain trim, or active filtering. Check input bias current against the sensor's source impedance and verify output swing at the required load. Because these limits are not stated in the indexed product excerpts, validate them in the manufacturer data sheet before finalizing resistor values.
מומלץ
Industrial Control Feedback
The LM358DR2 is suitable for industrial control loops where a 3 V to 32 V supply and dual-channel packaging simplify signal conditioning around a controller. One amplifier can condition the feedback sensor while the other shapes an error or reference signal. Its common-mode capability toward ground and VEE supports low-side feedback systems, but the output must remain inside the amplifier's valid swing region. Verify stability with the actual sensor network, compensation network, load, and operating temperature before production release.
מומלץ
Active Audio and Communication Filtering
The LM358DR2 can implement first-order active filters, signal conditioners, and channel buffers in low-frequency audio or communications equipment. Its two channels allow one stage to perform filtering while the other provides impedance buffering or gain control. The 8-pin SOIC package supports compact, automated board assembly. Performance checks should include the gain-bandwidth product, slew rate, output swing, noise, and stability with the selected source and load, because those characteristics must be confirmed from the manufacturer data sheet.
מומלץ
Potentiometer and Resistive Sensor Buffering
The LM358DR2 is a practical choice for buffering potentiometer positions or resistive sensors whose signal is referenced close to ground. The amplifier prevents the sensor divider from being loaded by the following stage and can provide adjustable gain through external feedback components. Evaluate bias-current error, offset voltage, and output-current demand for the sensor impedance and load. Confirm that the common-mode input remains within the operating range throughout the complete sensor movement.
מומלץ
Power-Supply Feedback and Monitoring
The LM358DR2 can amplify a scaled power-supply feedback voltage or monitor a current-shunt signal in an industrial or automotive-style power system. Its listed 3 V to 32 V supply range allows operation from elevated rails, while the ground-referenced common-mode range supports low-side measurements. Use the two channels for a differential measurement or monitoring function, and make sure the shunt signal, amplifier supply, and ground reference do not exceed the device's common-mode and output limits.
מומלץ
Portable Measurement and IoT Interfaces
The LM358DR2 can serve as the analog front end of a compact measurement or IoT interface when the system uses a supply within 3 V to 32 V and the sensor operates close to ground. Its dual channels support amplification followed by filtering or channel multiplexing, while the low-power-drain architecture is useful in portable equipment. The designer should still calculate the complete system error budget, including sensor error, bias current, offset, and ADC behavior, and verify current consumption for the intended duty cycle.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM358DR2 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM2904 | TP358 | SGMI8358 | BP358 | NSMOP-358 |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | 3PEAK | SGMC | 3PEAK | NSC |
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Amplifier Configuration | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
| Single-Supply Operating Range | 3 V to 32 V | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison |
| Common-Mode Input Range | Extends to ground and VEE | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison |
| Supply Configuration | Single supply or split supply | Single supply or split supply family operation | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison |
| Power Consumption | Low power drain | Low-power family operation | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison | Not specified in the indexed comparison |
| Pin Compatibility | 8-pin SOIC LM358 family pinout | Pin-compatible LM358-family replacement | Pin-compatible LM358-family replacement | Pin-compatible LM358-family replacement | Pin-compatible LM358-family replacement | Pin-compatible LM358-family replacement |
| Primary Application | General-purpose single- or split-supply analog signal conditioning | General-purpose dual operational amplification | General-purpose dual operational amplification | General-purpose dual operational amplification | General-purpose dual operational amplification | General-purpose dual operational amplification |
מבדילים עיקריים
- Broad listed single-supply operating range (לעומתLM2904)
- Dual channels in a compact surface-mount package (לעומתSGMI8358)
- Common-mode operation extending toward ground and VEE (לעומתBP358)
- Flexible single- or split-supply operation (לעומתNSMOP-358)
הערות תכנון
Place the supply bypass capacitor immediately beside the LM358DR2 power and ground pins. Keep the feedback components, input traces, and output trace short so that parasitic resistance and capacitance do not alter the intended gain or phase margin. The two channels are electrically separate even though they share supply pins, so high-current output routing on one channel should not be placed in the signal-ground path of the other.
Do not assume rail-to-rail input or output behavior. The verified product description specifies a common-mode range extending to ground and VEE, but the usable range still depends on the supply arrangement and operating conditions. Verify the input common-mode limits, output swing, output-current capability, and stability for the selected gain from the manufacturer data sheet before using the device near a rail.
Separate analog signal paths from switching-converter currents and digital return paths. Use a compact ground connection for the amplifier, place the bypass capacitor at the device pins, and route sensor inputs away from high-voltage or fast-switching nodes. For high-impedance sensors, minimize leakage from board contamination and guard exposed input nodes when the sensor impedance makes bias-current error significant.
The 3 V minimum listed supply voltage applies to the device itself, not automatically to every valid input and output combination. Confirm the available rail voltage, allowable input range, and required output level under minimum and maximum load. When using split supplies, check both positive and negative rail limits and ensure the common-mode and output-swing restrictions remain satisfied across the complete signal range.
מידע על תאימות
No specific compliance declaration was identified in the indexed product results. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status using the manufacturer's current product documentation and the exact ordering code.