LT1206CR - 250mA, 60MHz Current Feedback Amplifier | Analog Devices
MPN: LT1206CR ✓ פעילLT1206CR סקירה
A current-feedback amplifier is a voltage-input, current-output feedback topology within the broader operational-amplifier and analog signal-conditioning product hierarchy. Unlike a conventional voltage-feedback amplifier, the LT1206CR controls a differential current rather than an error-voltage gain, enabling wide bandwidth and high slew-rate performance while preserving low distortion. It is positioned as an analog amplifier IC for video, communications, and signal-chain systems that need more output drive than a general-purpose op amp provides.
Verified manufacturer information identifies 250mA minimum output drive, 60MHz bandwidth, a 900V/us maximum slew-rate value, 0.02% differential-gain error, and 0.17 degrees differential phase. The device operates across a wide supply range and accepts supplies up to ±15V. A shutdown function places the amplifier in a high-impedance, low-current mode, with shutdown current below 200uA, helping reduce dissipation when the circuit is inactive.
The LT1206 is particularly suitable for video because it combines high bandwidth, high output current, and excellent video characteristics. It is also stable with large capacitive loads and can supply the current required by capacitive input and output networks. The adjustable supply-current feature allows engineers to balance performance and power consumption according to the source impedance, load, and operating conditions of a specific board.
Typical uses include video buffering, cable-driver interfaces, active video filters, video distribution, communications equipment, and test and measurement systems. In these applications, the 60MHz bandwidth and 250mA output-current capability provide useful margin for signal transmission and load driving, while the shutdown feature supports systems that periodically disable the amplifier.
When laying out the circuit, use short feedback paths, maintain the feedback network close to the amplifier, and account for the DDPAK-7 thermal-pad connection when calculating copper heat spreading. Because the exact pin names and exposed-tab assignment are not present in the supplied verified snippets, the package drawing is not populated rather than presenting an unverified pinout. Consult the official LT1206 datasheet before PCB release or substitution.
This page consolidates the verified Analog Devices product information, distributor availability references, package details, and practical selection guidance for the LT1206CR. It also distinguishes device-level evidence from unresolved replacement and pricing data, helping engineers avoid treating generic op-amp alternatives as true pin-compatible drop-ins.
חלופות תחליף ישיר עבור LT1206CR — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
LT1206CR#PBF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LT1206CR דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Current Feedback Amplifier |
| Number of Circuits | 1 circuit |
| Minimum Output Drive Current | 250 mA |
| Bandwidth | 60 MHz |
| Slew Rate | 100 V/us to 900 V/us |
| Differential Gain Error | 0.02% |
| Differential Phase | 0.17 degrees |
| Input Impedance | 10 M ohms |
| Supply Voltage Range | 10 V to 30 V |
| Maximum Supply Voltage | ±15 V |
| זרם כיבוי | <200 uA |
| זרם אספקה | Adjustable |
| Capacitive Load Stability | Stable with large capacitive loads |
| מארז | 7-lead DDPAK |
| Input Offset Voltage | 15 mV maximum |
מדריך תצורת פינים של LT1206CR 7-lead ddpak
תצורת פינים עבור LT1206CR (מארזת 7-lead ddpak). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור LT1206CR.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LT1206CR מתאים עבור 6 יישוםs: Video Signal Buffering, Active Video Filter, Video Cable-Driver Output, Communications Signal Conditioning, Capacitive-Load Output Stage, Test and Measurement Front End.
Video Signal Buffering
The LT1206CR is well suited to video signal buffering because it combines 60MHz bandwidth with at least 250mA output-drive current and a maximum slew rate of 900V/us. Its verified 0.02% differential-gain error and 0.17-degree differential phase also support faithful video amplification. The amplifier can sit between a video source and a downstream cable, monitor, or distribution stage, reducing source loading while preserving signal amplitude and timing. The benefit depends on keeping feedback traces short and providing adequate output-current margin for the connected load.
מומלץ
Active Video Filter
The LT1206CR can implement an active video filter when the design requires both wide bandwidth and stronger output drive than a general-purpose operational amplifier provides. Its 60MHz bandwidth and 900V/us maximum slew rate allow the filter to process video-rate signals without relying on a slow output stage. Current-feedback topology and the 10M-ohm input impedance help the amplifier interact predictably with external feedback networks. Engineers should calculate gain-bandwidth behavior from the selected feedback resistor and verify stability, output swing, and load current against the intended video impedance.
מומלץ
Video Cable-Driver Output
The LT1206CR’s 250mA minimum output-drive current is useful when driving a terminated video cable or distributing a composite signal across multiple stages. Unlike a low-current amplifier, it has the drive capability required by capacitive cable loading while maintaining 60MHz bandwidth and a slew rate reaching 900V/us. The device can therefore reduce source loading and preserve signal integrity in longer interconnects. Layout remains important: short output paths, controlled return geometry, and appropriate source termination help limit reflections and ringing.
מומלץ
Communications Signal Conditioning
The LT1206CR is applicable to communications equipment that needs a high-output-drive analog stage rather than a precision-only instrumentation amplifier. Its 60MHz bandwidth, 10M-ohm input impedance, and 900V/us maximum slew rate support higher-frequency signal conditioning, while the shutdown current below 200uA supports power-conscious equipment that operates intermittently. The amplifier must still be matched to the source impedance and communication bandwidth, and its gain and phase characteristics should be checked over the full signal range before production release.
מומלץ
Capacitive-Load Output Stage
The LT1206CR is specifically useful as an output stage for capacitive loads because the manufacturer describes it as stable with large capacitive loads and capable of supplying the required current. Its minimum output-drive specification of 250mA is substantially higher than that of many precision op amps, reducing the risk that load capacitance will dominate amplifier behavior. When designing the stage, include output-current and dissipation checks, monitor output settling at the target frequency, and place feedback components close to the device to minimize parasitic feedback paths.
מומלץ
Test and Measurement Front End
The LT1206CR can serve as a high-drive input or output stage in test and measurement equipment when the source or load requires more current than a conventional precision amplifier can provide. Its 60MHz bandwidth, 250mA output-drive capability, and 900V/us maximum slew rate help preserve fast transient behavior at the interface. The 10M-ohm input impedance helps limit loading of the measured source, although the complete system must account for resistor network noise and parasitic capacitance. The shutdown function can reduce power when the measurement channel is inactive.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LT1206CR — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LT1206CR#PBF |
|---|---|---|
| Package | 7-lead DDPAK | 7-lead DDPAK |
| Brand | Analog Devices | Analog Devices |
| Amplifier Type | Current Feedback Amplifier | Current Feedback Amplifier |
| Minimum Output Drive Current | 250 mA | 250 mA |
| Bandwidth | 60 MHz | 60 MHz |
| Maximum Slew Rate | 900 V/us | 900 V/us |
| Differential Gain Error | 0.02% | 0.02% |
| Differential Phase | 0.17 degrees | 0.17 degrees |
| Supply Voltage Range | 10 V to 30 V | 10 V to 30 V |
| Shutdown Current | <200 uA | <200 uA |
| Lead-Free Ordering Suffix | No #PBF suffix shown in target MPN | #PBF lead-free suffix |
מבדילים עיקריים
- High output-drive capability (לעומתGeneral-purpose op amps such as TS556ID)
- Wideband current-feedback performance (לעומתMC1458D)
- Capacitive-load drive (לעומתNE5534DR)
הערות תכנון
Keep the feedback resistor, feedback capacitor, and input connections close to the LT1206CR. Current-feedback amplifiers are sensitive to parasitic feedback introduced by long signal paths. Route the output to the load through a short, wide trace where practical, and return the load current directly to the device ground rather than through distant analog-ground paths.
Calculate dissipation from the actual output voltage, supply voltage, quiescent current, and load current before assigning copper area. The DDPAK package can remove substantial heat through its tab and PCB copper, but the verified snippets do not provide thermal resistance or junction-temperature limits. Use the manufacturer datasheet for those values and confirm the board’s tab and copper connection during layout review.
Validate large-capacitive-load operation at the lowest intended gain and maximum target bandwidth. Although the LT1206 is specified as stable with large capacitive loads, output current, output swing, and settling behavior still depend on load magnitude and frequency. Probe directly at the device and include output-current margin so capacitive transients do not force the amplifier outside its rated operating region.
מידע על תאימות
The verified LT1206CR#PBF ordering code includes a lead-free finish designation, but the supplied data does not explicitly provide RoHS, REACH, halogen-free, conflict-minerals, or AEC-Q100 statements. AEC-Q100 is treated as not applicable because the product is an analog amplifier rather than an automotive-qualified device identified by the supplied data.
