MAX3232ECPW - Dual RS-232 Transceiver | Texas Instruments
MPN: MAX3232ECPW ✓ פעילMAX3232ECPW סקירה
An RS-232 transceiver is an interface IC that converts logic-level signals from a processor or controller into RS-232 voltage levels, while converting received RS-232 signals back into logic-compatible levels. Within the hierarchy of interface ICs, serial transceivers connect digital controllers to communication ports using the TIA/EIA-232-F electrical standard. The MAX3232ECPW uses an on-chip charge pump to generate positive and negative RS-232 voltages from one low-voltage supply.
The device accepts supply voltages from 3 V to 5.5 V and operates at data-signaling rates up to 250 kbit/s. Its two transmitters and two receivers support full-duplex serial links, while driver output slew rate is limited to 30 V/µs. Pin-to-pin ESD protection rated at ±15 kV improves system robustness when cables are connected or disconnected.
The MAX3232ECPW is the commercial-temperature version of the MAX3232E family, specified for 0 °C to 70 °C. It is packaged in a 16-pin gull-wing TSSOP with a 4.4 mm lead pitch. Four external charge-pump capacitors are required, allowing the interface to operate from a single 3 V or 5 V rail without a separate negative power supply.
Typical uses include industrial serial adapters, data-acquisition equipment, point-of-sale terminals, laboratory instruments, and service-console links. The device is appropriate when a controller needs an RS-232 port but cannot generate the positive and negative voltages required by legacy RS-232 drivers directly.
Place the four charge-pump capacitors close to their associated pins and keep the exposed supply and ground paths short. Keep the RS-232 connector interface physically separated from sensitive analog or high-speed digital routing, and provide appropriate board-level protection when exposed cables exceed the device's rated ESD withstand.
This product page combines electrical specifications, package and pin information, drop-in replacement analysis, application guidance, and design notes for engineers evaluating the MAX3232ECPW in 3 V and 5 V RS-232 interfaces.
חלופות תחליף ישיר עבור MAX3232ECPW — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MAX3232ECPW (אותו גורם צורה וטביעת רגל) — שונים ב Product Type, Supply Voltage Range, ESD Protection, Maximum Data Rate, Package.
MAX3232CPWR
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←MAX3232IPW
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←MAX3232EWP
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
MAX3232EA
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
ST3232CTR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX3232ECPW מפרטים
| Product Type | Dual RS-232 line transceiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Number of Line Drivers | 2 channels |
| Number of Line Receivers | 2 channels |
| Maximum Data Signaling Rate | 250 kbit/s |
| Maximum Driver Output Slew Rate | 30 V/µs |
| IEC ESD Protection | ±15 kV |
| RS-232 Compliance | TIA/EIA-232-F |
| Charge Pump | Dual charge-pump circuit |
| External Charge-Pump Capacitors | 4 capacitors |
| טווח טמפרטורת פעולה | 0 °C to 70 °C |
| Temperature Grade | Commercial |
| מארז | 16-pin TSSOP |
| Lead Pitch | 4.4 mm |
| מספר פינים | 16 pins |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
תצורת פינים של MAX3232ECPW
| פין 1 | R1IN — Receiver 1 input |
| פין 2 | R1OUT — Receiver 1 output |
| פין 3 | R2IN — Receiver 2 input |
| פין 4 | R2OUT — Receiver 2 output |
| פין 5 | GND — Ground connection |
| פין 6 | V+ — Positive charge-pump output |
| פין 7 | C2+ — Charge-pump capacitor 2 positive terminal |
| פין 8 | C1+ — Charge-pump capacitor 1 positive terminal |
| פין 9 | C1- — Charge-pump capacitor 1 negative terminal |
| פין 10 | C2- — Charge-pump capacitor 2 negative terminal |
| פין 11 | V- — Negative charge-pump output |
| פין 12 | T1IN — Transmitter 1 logic input |
| פין 13 | T2IN — Transmitter 2 logic input |
| פין 14 | T1OUT — Transmitter 1 RS-232 output |
| פין 15 | T2OUT — Transmitter 2 RS-232 output |
| פין 16 | VCC — Device supply input |
יישומים טיפוסיים
MAX3232ECPW מתאים עבור 6 יישוםs: Industrial Serial Port Interface, Point-of-Sale Terminal, Data Acquisition Equipment, Laboratory Instrument Console, Service and Configuration Port, Embedded System Serial Adapter.
Industrial Serial Port Interface
The MAX3232ECPW is suitable for industrial controllers that require a legacy RS-232 port but operate from a 3.3 V or 5 V logic rail. Its dual charge-pump circuit generates the positive and negative voltages needed by the RS-232 interface from one 3 V to 5.5 V supply, avoiding a separate negative rail. The two transmitters and two receivers support full-duplex communication at rates up to 250 kbit/s. The ±15 kV IEC ESD protection is valuable when the connector is accessible to service personnel or connected equipment. Place the four charge-pump capacitors close to pins 7 through 10 and route the exposed connector interface away from sensitive circuitry.
מומלץ
Point-of-Sale Terminal
Point-of-sale equipment can use the MAX3232ECPW to connect a controller to a receipt printer, scanner, or service terminal through RS-232. The 250 kbit/s maximum signaling rate covers common serial-port traffic while the controlled 30 V/µs driver slew rate supports compliant RS-232 transitions. Operation from a single 3 V to 5.5 V rail simplifies system power design, and the integrated charge pump removes the need for a discrete negative supply generator. Because peripherals may be connected by user-accessible cables, the ±15 kV IEC ESD protection improves connector-side robustness. Maintain a low-impedance ground path between the transceiver and connector and consider additional surge protection for installations exposed to severe transients.
מומלץ
Data Acquisition Equipment
The MAX3232ECPW provides a compact interface between a data-acquisition controller and an RS-232-compatible instrument. Its 250 kbit/s capability is appropriate for configuration commands, measurement results, and status reporting in many laboratory and industrial systems. The 16-pin TSSOP package preserves board area while the single 3 V to 5.5 V supply operation simplifies rail planning around modern processors and FPGAs. The ±15 kV IEC ESD rating helps protect the interface when instrument cables are routinely reconnected. Keep the four external charge-pump capacitors near the IC and provide a quiet ground connection, because cable transients and ground potential differences can otherwise affect communication reliability.
מומלץ
Laboratory Instrument Console
MAX3232ECPW can serve as the host-side RS-232 interface in laboratory instruments that retain legacy serial consoles. A computer or embedded controller communicates through the two receiver channels, while the two driver channels support bidirectional command and data transfer. The device's 250 kbit/s maximum data rate is suitable for terminal sessions, configuration files, and instrument status messages. Running from a 3 V to 5.5 V supply permits use with both legacy 5 V controllers and modern 3.3 V systems. The integrated charge pump requires only four external capacitors and no separate negative supply, reducing board complexity. The commercial 0 °C to 70 °C rating should be checked against the instrument's internal temperature environment.
מומלץ
Service and Configuration Port
The MAX3232ECPW is well suited to equipment that retains a service or configuration connector for diagnostics, firmware loading, and parameter adjustment. Its bidirectional 250 kbit/s interface supports both command transmission and status reception. The ±15 kV IEC ESD protection is particularly relevant to service ports because technicians frequently connect and disconnect cables. A single 3 V to 5.5 V supply allows the transceiver to operate directly alongside embedded processors without an additional negative-voltage rail. Designers should keep the RS-232 trace away from clocks, ADC inputs, and switching-converter power nodes, and should verify that the external connector does not introduce ground offsets beyond the device interface tolerances.
מומלץ
Embedded System Serial Adapter
An embedded controller can use the MAX3232ECPW to add a conventional RS-232 port to a system built around a 3.3 V processor. The device converts logic-level transmit inputs into RS-232 levels and converts received signals back to logic-compatible outputs, while the internal charge pump supplies the required positive and negative voltages. Its 16-pin TSSOP footprint supports compact single-board designs, and 250 kbit/s operation covers legacy printer, modem, and instrument-control links. Four charge-pump capacitors are required for operation. Place them close to the associated pins, minimize loop area around the charge-pump nodes, and preserve an uninterrupted ground connection between the IC, connector shield, and chassis or enclosure grounding strategy.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MAX3232ECPW — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MAX3232CPW | MAX3232IPW | MAX3232EWP | MAX3232EA | ST3232CTR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Product Type | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s | 250 kbit/s | 250 kbit/s | 250 kbit/s | 250 kbit/s | 250 kbit/s |
| Line Drivers | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Line Receivers | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| External Charge-Pump Capacitors | 4 capacitors | 4 capacitors | 4 capacitors | 4 capacitors | 4 capacitors | 4 capacitors |
מבדילים עיקריים
- Enhanced connector-side ESD protection (לעומתMAX3232CPW)
- Commercial-temperature option supports cost-sensitive room-temperature equipment (לעומתMAX3232IPW)
- Single-supply operation simplifies embedded interfaces (לעומתMC1488NE4)
- Pin-compatible second-source option (לעומתST3232CTR)
הערות תכנון
Place the four charge-pump capacitors close to pins 7 through 10 using short traces and a compact ground connection. These nodes switch at high frequency, so excessive loop area can increase radiated emissions and coupling into nearby analog circuitry. Follow the capacitor values and topology shown in the Texas Instruments datasheet. Keep the RS-232-side routing away from clocks, ADC inputs, switching-regulator power nodes, and sensitive sensor signals.
Do not treat the MAX3232ECPW as a 5 V-only RS-232 circuit. Its specified single-supply operating range is 3 V to 5.5 V, and the charge-pump capacitor requirements can vary with supply conditions. Use the manufacturer-recommended capacitor values and ensure that transmitter input levels remain compatible with the VCC rail. Also distinguish logic-side pins 12 and 13 from RS-232-side outputs 14 and 15 during schematic review.
The 30 V/µs maximum transmitter slew rate controls RS-232 edge speed, but cable and board radiation can still be significant. Route T1OUT and T2OUT as short, impedance-controlled paths to the connector, maintain a continuous ground reference beneath the pair, and avoid adding unnecessary stubs. For enclosure-mounted connectors, evaluate whether additional board-level TVS or surge protection is required rather than assuming the device's ±15 kV IEC ESD rating covers every external fault condition.
RS-232 is a single-ended, unbalanced interface, and ground potential differences can cause communication errors. Connect the transceiver ground to the connector ground with a low-impedance path and evaluate whether a chassis or signal-ground connection is required for long cable runs. Do not use the charge-pump V+ and V- pins as general supply rails; they are generated specifically for the line drivers and should not power external circuitry.
מידע על תאימות
The manufacturer product page confirms TIA/EIA-232-F compliance and ±15 kV IEC ESD protection, but it does not provide RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations.