MAX4851HETE - Quad SPST Over-Rail Switch | Analog Devices
MPN: MAX4851HETE ✓ פעילMAX4851HETE סקירה
An analog switch is a semiconductor device that routes an electrical signal between external terminals under digital control. The SPST designation means each of the four channels has one signal path, while the quad configuration integrates four switches into one package. In the device hierarchy, MAX4851HETE belongs to the analog-switch, interface-IC, and semiconductor categories. This integration allows one controller to manage several independently switched signal lines on a compact circuit board.
Over-rail signal handling is the principal functional distinction of the MAX4851 family. This characteristic allows the switched signal to extend beyond the nominal supply-voltage range, which is useful when a source can present a voltage above or below the switch’s normal operating rails. The 2 V to 5.5 V operating range also supports both lower-voltage and conventional 5 V system environments. The compact 16-pin TQFN package reduces PCB area compared with larger switch packages.
The MAX4851HETE is designed for signal routing where rapid transitions and channel isolation matter. Its 100 ns turn-on and 60 ns turn-off times provide substantially faster switching than many mechanical relay implementations. The 80 dB isolation specification helps reduce unwanted coupling between channels, while the 4.5 ohm on resistance suits applications where moderate insertion resistance is acceptable. These characteristics position the device between low-cost mechanical relays and more specialized high-performance switch networks.
Typical uses include test and measurement signal routing, industrial control interfaces, communication-line switching, instrumentation multiplexing, and embedded systems that must route external signals under firmware control. It can also support over-rail input conditioning when the controlling system has a different voltage domain. The extended -40°C to +85°C range makes it appropriate for industrial equipment where room-temperature commercial components would be insufficient.
Designers should verify every signal’s absolute maximum voltage, logic threshold, and permitted over-rail condition before routing it through the switch. Input and ground connections should have low impedance paths, while unused control pins should be driven to a defined state. Because on resistance contributes insertion loss and consumes power, sensitive high-frequency or precision analog paths should be checked for bandwidth and attenuation rather than relying only on nominal transition time.
This product page combines the MAX4851 family specifications, package details, sourcing information, and engineering guidance with same-package replacement analysis. It also highlights the practical distinction between fast semiconductor switching, over-rail operation, channel isolation, and the trade-offs associated with the device’s 4.5 ohm on resistance.
חלופות תחליף ישיר עבור MAX4851HETE — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MAX4851HETE (אותו גורם צורה וטביעת רגל) — שונים ב Package, Switch Configuration.
MAX4851EETE
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX4853HETE
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MAX4853EETE
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX4851HETE דירוגים מרביים ומאפיינים חשמליים
| Product Type | Quad SPST analog switch with over-rail signal handling |
| Number of Switch Channels | 4 channels |
| Switch Configuration | SPST |
| Supply Voltage Range | 2 V to 5.5 V |
| On Resistance | 4.5 ohm |
| Switch Resistance Family | 3.5 ohm / 7 ohm |
| Turn-On Time | 100 ns |
| Turn-Off Time | 60 ns |
| Isolation | 80 dB |
| טווח טמפרטורת פעולה | -40°C to +85°C |
| מארז | 16-pin TQFN, 3 mm × 3 mm |
| מספר פינים | 16 pins |
| סוג הרכבה | Surface mount |
| Device Marking | +ABX |
| Signal Handling | Over-rail signal handling |
מדריך תצורת פינים של MAX4851HETE 16-pin tqfn, 3 mm × 3 mm
תצורת פינים עבור MAX4851HETE (מארזת 16-pin tqfn, 3 mm × 3 mm). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור MAX4851HETE.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
MAX4851HETE מתאים עבור 6 יישוםs: Industrial Test and Measurement Signal Routing, Communication-Line Switching, Embedded Control and Peripheral Switching, Instrumentation Signal Multiplexing, Data Acquisition Front Ends, Security and Surveillance Control.
Industrial Test and Measurement Signal Routing
The MAX4851HETE fits laboratory and industrial test systems that must route several instrument signals under software control. Its four SPST channels provide a compact alternative to a bank of slower mechanical relays, while 100 ns turn-on and 60 ns turn-off times shorten the interval between routing commands. The stated 80 dB isolation helps separate routed channels, and operation from -40°C to +85°C supports industrial equipment. Engineers should verify the input bandwidth, signal-level limits, and control truth table before connecting external sources.
מומלץ
Communication-Line Switching
MAX4851HETE can route communication or control lines in equipment where compactness and fast operation are important. Over-rail signal handling is valuable when a connected peripheral can present a voltage outside the switch’s normal 2 V to 5.5 V supply range. Four independently controlled channels reduce component count, and the 3 mm by 3 mm TQFN preserves board area. The 4.5 ohm on resistance must be acceptable for the signal being routed, while the 80 dB isolation specification should be checked against crosstalk requirements.
מומלץ
Embedded Control and Peripheral Switching
The MAX4851HETE is appropriate for embedded systems that need to connect or disconnect external lines under MCU or FPGA control. Its 60 ns turn-off and 100 ns turn-on times permit fast switching, while four channels provide convenient integration in a 16-pin TQFN. The 2 V minimum supply supports integration with suitable low-voltage logic systems, but control thresholds must be checked against the selected MCU or FPGA. For long external lines, add protection appropriate to the environment and validate the complete signal path for ringing.
מומלץ
Instrumentation Signal Multiplexing
A MAX4851HETE-based design can multiplex several instrumentation signals through a compact analog-routing network. The four SPST channels provide independent control paths, and the 80 dB isolation figure supports designs requiring meaningful separation between channels. The 4.5 ohm on resistance adds attenuation, so precision measurements may require a lower-resistance switch or an appropriate buffer. Keep trace lengths short, use a stable ground reference, and verify that switching transients do not corrupt the measurement window.
מומלץ
Data Acquisition Front Ends
The MAX4851HETE can implement controlled signal selection in data-acquisition front ends where multiple sensor or test channels must reach a common processing chain. Its fast switching behavior allows channel changes with less delay than electromechanical relays, and the small TQFN footprint supports compact multi-channel boards. Four channels can be expanded for larger systems, although off-state leakage, bandwidth, and charge injection should be checked against the sensor impedance and acquisition timing. The manufacturer data sheet supplies the authoritative electrical limits.
מומלץ
Security and Surveillance Control
MAX4851HETE is suitable for surveillance equipment that switches or isolates video-related control or sensor lines. Its compact 16-pin TQFN package preserves PCB area in camera and controller assemblies, while four channels permit coordinated routing. The over-rail feature helps accommodate signal levels that may differ from the logic supply. Actual video analog paths normally require very low capacitance and higher bandwidth, so the device is better suited to control, monitoring, or auxiliary lines than high-definition video conductors. Protection against external transients remains essential.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MAX4851HETE — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MAX4851EETE | MAX4853HETE | MAX4853EETE |
|---|---|---|---|---|
| Package | 16-pin TQFN, 3 mm × 3 mm | 16-pin TQFN, 3 mm × 3 mm | 16-pin TQFN, 3 mm × 3 mm | 16-pin TQFN, 3 mm × 3 mm |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Switch Configuration | Quad SPST | Quad SPST | Quad SPST | Quad SPST |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| On Resistance | 4.5 ohm | 3.5 ohm / 7 ohm family | 3.5 ohm / 7 ohm family | 3.5 ohm / 7 ohm family |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
| Signal Handling | Over-rail signal handling | Over-rail signal handling | Over-rail signal handling | Over-rail signal handling |
מבדילים עיקריים
- Compact four-channel over-rail switching (לעומתMAX4851EETE)
- Fast complementary switching response (לעומתMAX4853HETE)
- Extended industrial temperature capability (לעומתMAX4853EETE)
הערות תכנון
Do not assume that over-rail handling removes all absolute-maximum limits. Confirm the permitted signal excursion, supply state, and control-pin level for every operating mode in the Analog Devices data sheet. The MAX4851HETE operates from 2 V to 5.5 V and supports over-rail signal handling, but transient duration, polarity, and fault-current behavior can still constrain a design. Apply appropriate external protection when long cables or inductive loads can introduce large excursions.
Place input and output decoupling capacitors close to the 16-pin TQFN power and ground connections, and use a low-impedance ground plane beneath the device. Follow the manufacturer’s exposed-pad land pattern and assembly recommendations for the TQFN package. Keep switched-signal traces short and separate from control and clock routing where possible. Because the stated 4.5 ohm on resistance creates attenuation, precision and high-frequency paths should be evaluated for bandwidth rather than only insertion resistance.
Account for switch capacitance, off-state leakage, and charge injection when the switched source has a high impedance or when measurement timing is critical. The published 100 ns turn-on and 60 ns turn-off times describe switching speed, not the settling time of the complete analog path. Establish an acquisition dead time after each switching command and compare the resulting error with the converter’s resolution. For high-speed signals, validate bandwidth and crosstalk using the actual board layout.
Estimate the average supply current from the device quiescent current, control-state current, and the dynamic current required by the switched paths. The MAX4851HETE uses a 2 V to 5.5 V supply, so the chosen regulator must maintain the required voltage during switching transients. Decouple the supply locally and avoid routing return current through sensitive analog paths. The precise power-consumption figures should be taken from the manufacturer data sheet under the intended control and signal conditions.
מידע על תאימות
No definitive environmental or material-compliance statement was identified in the manufacturer page snippet or distributor specifications. Confirm the current declarations with Analog Devices before using the part in a compliance-controlled design.
