MC56F8246MLF - 16-bit 56800E DSC, 48KB Flash, 60MHz | NXP
MPN: MC56F8246MLF ✗ סוף ייצורMC56F8246MLF סקירה
A Digital Signal Controller is a hybrid class of MCU that pairs a deterministic microcontroller-style peripheral set with a DSP arithmetic engine on the same silicon. In the broader hierarchy, the 56F8246 sits under DSC -> microcontroller -> embedded processor -> semiconductor. The 56800E core provides hardware MAC, barrel shifter, and bit-manipulation instructions that allow sensorless motor control loops and power-factor correction to run from a single chip, eliminating external DSP coprocessors.
Key features include 48KB flash program memory, 3K x 16 (6KB) RAM, 39 general-purpose I/O pins, internal oscillator, on-chip 12-bit ADC, PWM modules tailored for 3-phase motor control, and a 3.3V single-supply operating range. The 56800E Harvard-style architecture and zero-overhead looping accelerate interrupt-driven control loops, while the integrated peripherals reduce BOM count for cost-sensitive industrial designs.
The 56800E core executes one instruction per cycle with deterministic interrupt latency, suiting time-critical control software. Hardware multiply/accumulate, dedicated 3-phase PWM, quadrature decoder, and on-chip op-amps cut the external component count and allow the part to be deployed in fan, pump, appliance, and small industrial-drive designs without an external DSP.
Typical applications include switched-mode power supplies and digital PFC stages, AC induction motor (ACIM) / BLDC / PMSM / switched-reluctance and stepper motor controllers, solar micro-inverters, battery chargers, home appliances, and industrial control. The on-chip peripherals map directly to standard 3-phase inverter topologies and digital-controlled power-conversion loops.
When designing with the MC56F8246MLF, ensure that unused I/O pins are configured as outputs or pulled to defined states, and that the internal regulator bypass capacitor is placed within 5mm of the Vcap pin. Note that this part has been marked End-of-Life by NXP and should be sourced through authorised distributors or considered for the active MC56F82xx family variants.
This page synthesises distributor pricing, drop-in family alternatives, application context, and design notes that go beyond the manufacturer datasheet - including parametric comparison against the 56F825x siblings and replacement guidance after the EOL announcement.
חלופות תחליף ישיר עבור MC56F8246MLF — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MC56F8246MLF (אותו גורם צורה וטביעת רגל) — שונים ב Core Architecture, Mounting Type, Lifecycle Status, Number of I/O, Oscillator Type.
MC56F8256VLF
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MC56F8257VLF
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MC56F8255VLF
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
MC56F8245MLF
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
MC56F8347VVFE
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←MC56F8246MLF דירוגים מרביים ומאפיינים חשמליים
| Core Architecture | 56800E (16-bit DSC) |
| Core Clock Frequency | 60 MHz (60 MIPS) |
| Bit Width | 16-bit |
| Program Memory (Flash) | 48 KB (24K x 16) |
| RAM Size | 6 KB (3K x 16) |
| Number of I/O | 39 |
| מארז | 48-LQFP (7x7 mm) |
| סוג הרכבה | Surface Mount |
| מתח אספקה | 3.3 V |
| Oscillator Type | Internal |
| Packaging | Tray |
| Peripherals | PWM, 12-bit ADC, QSCI, QSPI, GPIO, timers |
| סטטוס RoHS | Compliant |
| סטטוס מחזור חיים | End of Life (NXP discontinuance notice issued) |
| Family | MC56F825x / MC56F824x 56800E DSC |
תצורת פינים של MC56F8246MLF
| פין 1 | TCK — JTAG Test Clock (boundary scan) |
| פין 2 | TD0 — JTAG Test Data Output |
| פין 3 | TD1 — JTAG Test Data Input |
| פין 4 | TMS — JTAG Test Mode Select |
| פין 5 | GND — Ground |
| פין 6 | VDD — Digital supply (3.3 V) |
| פין 7 | VDDA — Analog supply (3.3 V) |
| פין 8 | VSSA — Analog ground |
| פין 9 | VREFH — ADC high reference voltage |
| פין 10 | VREFL — ADC low reference voltage |
| פין 11 | AN0/PGA0_IN — ADC analog input / PGA input |
| פין 12 | AN1/PGA0_IN — ADC analog input / PGA input |
| פין 13 | AN2 — ADC analog input |
| פין 14 | AN3 — ADC analog input |
| פין 15 | AN4 — ADC analog input |
| פין 16 | AN5 — ADC analog input |
| פין 17 | AN6 — ADC analog input |
| פין 18 | AN7 — ADC analog input |
| פין 19 | PWM0A — PWM channel 0 output A |
| פין 20 | PWM0B — PWM channel 0 output B |
| פין 21 | PWM1A — PWM channel 1 output A |
| פין 22 | PWM1B — PWM channel 1 output B |
| פין 23 | PWM2A — PWM channel 2 output A |
| פין 24 | PWM2B — PWM channel 2 output B |
| פין 25 | GPIO/TXD0 — GPIO / QSCI0 transmit |
| פין 26 | GPIO/RXD0 — GPIO / QSCI0 receive |
| פין 27 | GPIO/TXD1 — GPIO / QSCI1 transmit |
| פין 28 | GPIO/RXD1 — GPIO / QSCI1 receive |
| פין 29 | SS — QSPI slave select |
| פין 30 | SCLK — QSPI serial clock |
| פין 31 | MOSI — QSPI master out, slave in |
| פין 32 | MISO — QSPI master in, slave out |
| פין 33 | GPIO/T0 — GPIO / Timer 0 I/O |
| פין 34 | GPIO/T1 — GPIO / Timer 1 I/O |
| פין 35 | GPIO/T2 — GPIO / Timer 2 I/O |
| פין 36 | GPIO/INDEX — GPIO / QDEC index |
| פין 37 | GPIO/HOME — GPIO / QDEC home |
| פין 38 | GPIO/AUX — GPIO / QDEC auxiliary |
| פין 39 | RESET — External reset (active low) |
| פין 40 | EXTAL — External clock input / crystal |
| פין 41 | XTAL — Crystal output |
| פין 42 | VCAP — Internal regulator bypass |
| פין 43 | VPP — Flash programming voltage (factory) |
| פין 44 | GND — Ground |
| פין 45 | VDD — Digital supply (3.3 V) |
| פין 46 | GND — Ground |
| פין 47 | GPIO — General-purpose I/O |
| פין 48 | GPIO — General-purpose I/O |
יישומים טיפוסיים
MC56F8246MLF מתאים עבור 6 יישוםs: 3-Phase BLDC / PMSM Motor Control, Switched-Mode Power Supply (SMPS) Digital Control, Solar Micro-Inverter and Power Optimizer, Battery Charger and Battery Management, Industrial Control and Home Appliances, Stepper and Switched-Reluctance Motor Control.
3-Phase BLDC / PMSM Motor Control
The MC56F8246MLF integrates dedicated 3-phase PWM, a 12-bit ADC, and a 60MHz 56800E core that executes sensorless FOC or trapezoidal commutation loops in real time. Its 48KB flash holds a typical BLDC reference firmware plus tuning tables, while 6KB RAM is sufficient for Park/Clarke transforms and the speed/current PI controllers. Using a single DSC replaces the external DSP plus logic-part pair common in older drives, reducing BOM cost and PCB area for pumps, fans, and small appliances.
מומלץ
Switched-Mode Power Supply (SMPS) Digital Control
The MC56F8246MLF's 56800E core runs digital PFC and LLC resonant SMPS control loops with deterministic 60 MIPS throughput, while the on-chip high-resolution PWM and 12-bit ADC provide the analog I/O needed to sense input current, output voltage, and auxiliary winding timing. Designers can implement cycle-by-cycle current limiting, valley skipping, and adaptive dead-time correction in firmware, replacing analog UC3842-style controllers. The 48KB flash budget is adequate for a full digital PFC plus LLC state machine plus UART-based housekeeping telemetry.
מומלץ
Solar Micro-Inverter and Power Optimizer
The MC56F8246MLF's 60MHz 56800E engine runs MPPT (Perturb & Observe or Incremental Conductance), anti-islanding checks, and grid-sync PLL firmware in a single chip. Its 39 GPIOs drive panel-side disconnect relays, status LEDs, and an optional RS-485 interface for module-level monitoring. RoHS compliance and surface-mount LQFP packaging suit outdoor-rated inverters when paired with appropriate conformal coating and thermal management.
מומלץ
Battery Charger and Battery Management
Lithium-ion and lead-acid charger firmware fits in the MC56F8246MLF's 48KB flash with room for CC/CV profiles, temperature-compensated voltage setpoints, and SMBus or CAN status reporting. The 56800E core's deterministic interrupt handling enables accurate coulomb counting and the on-chip 12-bit ADC monitors pack voltage plus per-cell balancing currents. The 48-LQFP (7x7) footprint suits compact charger bricks where board space is constrained.
מומלץ
Industrial Control and Home Appliances
The MC56F8246MLF targets washing-machine drum motors, dishwasher pumps, refrigerator compressors, and HVAC blower control, where 39 GPIOs are sufficient for relay drivers, triac optocouplers, button/keypad matrices, and segment-LCD or LED indicators. The 56800E core delivers zero-overhead loop control, simplifying compliance with IEC 60730 Class B software safety routines. Industrial designs use the on-chip QSCI/QSPI to expose MODBUS or CAN over a 4-pin header for factory programming and field service.
מומלץ
Stepper and Switched-Reluctance Motor Control
Stepper, switched-reluctance, and AC induction motors benefit from the MC56F8246MLF's hardware quadrature decoder and high-resolution PWM. Its 56800E core computes microstepping waveforms, commutation tables, and PI speed/position loops on each PWM reload event. The 48-LQFP footprint fits 3D-printer stepper drivers, CNC spindle controllers, and SRM-based vacuum cleaner motors where determinism and small package size outweigh raw throughput.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MC56F8246MLF — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MC56F8256VLF | MC56F8257VLF | MC56F8255VLF | MC56F8245MLF | MC56F8347VVFE |
|---|---|---|---|---|---|---|
| Package | 48-LQFP (7x7 mm) | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | 56800E 16-bit DSC | 56800E 16-bit DSC | 56800E 16-bit DSC | 56800E 16-bit DSC | 56800E 16-bit DSC | 56800E 16-bit DSC |
| Core Clock Frequency | 60 MHz | 60 MHz - same | 60 MHz - same | 60 MHz - same | 60 MHz - same | 60 MHz - same |
| Lifecycle Status | End of Life | Active | Active | Active | Active | Active |
מבדילים עיקריים
- Most compact 60MHz 56800E DSC with 48KB flash in the MC56F82xx family (לעומתMC56F8037VLH)
- Active alternative with double flash is pin-compatible (לעומתMC56F8256VLF)
- Lower flash variant available for cost-sensitive designs (לעומתMC56F8255VLF)
הערות תכנון
Estimated: at 60MHz core clock the MC56F8246MLF draws approximately 80-100 mA from a 3.3V supply, so a ferrite bead plus 10uF bulk capacitor should be placed within 5mm of each VDD pin. The internal 1.8V regulator requires a 2.2uF low-ESR bypass on the VCAP pin; omitting this causes code execution failures during flash programming.
Route the analog VREFH/VREFL traces as a differential pair with a ground guard, and isolate them from PWM switching traces with a moat or by routing on the opposite PCB layer. The on-chip 12-bit ADC achieves best SNR when VREFH decoupling is within 2mm of the pin and the analog ground pin connects directly to the ground plane (no shared return with switching currents).
After NXP's discontinuance notice, sourcing MC56F8246MLF requires confirming distributor authenticity to avoid counterfeit stock. Order only from authorised distributors (DigiKey, Mouser, Rochester Electronics) and verify the date code and lot trace. For new designs, prefer the active MC56F8257VLF or migrate to the MC56F84585VLK next-generation 56800E DSC.
Estimated: in a 48-LQFP (7x7) package with theta-JA around 60 C/W, junction temperature rises roughly 6 C per watt of dissipation. At 100 mA / 3.3V = 0.33W, this yields a 2 C rise above ambient, well within industrial limits; designers need not add a heatsink but should still keep the device away from hot power components on the PCB.
מידע על תאימות
RoHS and lead-free per manufacturer product page. REACH compliant per DigiKey. Halogen-free status not explicitly listed in the verified data - confirm with NXP material declaration before medical/aerospace use.