PIC16C74B-04/PQ - 8-Bit 4MHz OTP MCU 7KB Flash | Microchip
MPN: PIC16C74B-04/PQ ✗ סוף ייצורPIC16C74B-04/PQ סקירה
A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, working RAM, and peripheral interfaces such as timers, A/D converters, and communication ports. Mid-range PIC microcontrollers occupy the middle of Microchip's 8-bit portfolio - more capable than the PIC16C5X baseline family and upward-compatible with PIC12CXXX devices, but predating the PIC18 enhanced family. The 'C' suffix in PIC16Cxx denotes OTP EPROM program memory, suitable for production runs where code stability is finalized but where in-circuit reprogrammability is not required; Flash-based 'F' variants are typically preferred for prototypes and field-updatable designs.
Key specifications include 8 channels of 8-bit Analog-to-Digital conversion, two additional 8-bit timers plus Timer0 and Timer1, two Capture/Compare/PWM (CCP) modules, and a synchronous serial port configurable as either 3-wire SPI or 2-wire I2C. A USART (Universal Synchronous/Asynchronous Receiver/Transmitter) provides asynchronous serial communication. The device supports high sink/source current of 25 mA per I/O, low standby current of 1 µA typical at 3V/32 kHz, and 15 µA typical operating current at 5V/4 MHz. Operating voltage spans 2.5V to 6.0V across commercial, industrial, and extended temperature grades.
The PIC16C74B architecture uses a Harvard-style RISC core with only 35 single-word instructions, simplifying firmware development and reducing code footprint. Its mid-range peripheral set - particularly the 8-channel ADC and dual CCP - positions it for analog signal acquisition, motor control, and industrial instrumentation. The wide operating voltage and temperature range extend use into automotive under-hood and harsh industrial environments.
Typical applications include industrial process control, motor drive interfaces, sensor signal conditioning, power supply monitoring, and embedded data acquisition systems. The 44-pin MQFP footprint suits designs where through-hole PDIP is too large but QFN is unavailable in the OTP memory configuration. When designing with the PIC16C74B-04/PQ, account for OTP memory constraints by finalizing firmware before programming, and consider the Flash-based PIC16F74 as a development substitute since both share the same die and pinout. This page synthesizes distributor pricing, drop-in PIC16C74B variants, and practical design notes not aggregated in any single manufacturer or distributor source.
חלופות תחליף ישיר עבור PIC16C74B-04/PQ — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם PIC16C74B-04/PQ (אותו גורם צורה וטביעת רגל) — שונים ב Serial Interfaces, Package, Core Architecture, Timers, Operating Temperature.
PIC16C74B-04I/PQ
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC16C74BT-04/PQ
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC16C74A-04/PQ
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC16C74AT-20I/PQ
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC16F74-I/PQ
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PIC16C74B-04/PQ דירוגים מרביים ומאפיינים חשמליים
| Core | PIC16 mid-range 8-bit RISC |
| Instruction Set Size | 35 single-word instructions |
| Program Memory | 7 KB (4K x 14) OTP EPROM |
| RAM | 192 bytes |
| תדר שעון מקסימלי | 4 MHz |
| Instruction Execution Time | 200 ns |
| Operating Voltage Range | 2.5 V to 6.0 V |
| Digital I/O Pins | 33 |
| A/D Converter | 8 channels x 8-bit |
| Timers | 3 (Timer0, Timer1, Timer2) |
| CCP Modules | 2 (Capture/Compare/PWM) |
| Serial Interfaces | SPI, I2C (MSSP), USART |
| I/O Sink/Source Current | 25 mA / 25 mA |
| Operating Current (5V, 4 MHz) | 15 µA typical |
| Standby Current (3V, 32 kHz) | 1 µA typical |
| מארז | 44-pin MQFP (10x10 mm) |
| סוג הרכבה | Surface Mount |
| טווח טמפרטורת פעולה | -40C to +125C (Extended) |
תצורת פינים של PIC16C74B-04/PQ
| פין 1 | MCLR/VPP — Master clear (reset) input / programming voltage |
| פין 2 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| פין 3 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| פין 4 | RA2/AN2 — PORTA bit 2 / Analog input 2 |
| פין 5 | RA3/AN3/VREF — PORTA bit 3 / Analog input 3 / ADC reference |
| פין 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| פין 7 | RA5/AN4/SS — PORTA bit 5 / Analog input 4 / SPI slave select |
| פין 8 | RE0/RD/AN5 — PORTE bit 0 / Read control / Analog input 5 |
| פין 9 | RE1/WR/AN6 — PORTE bit 1 / Write control / Analog input 6 |
| פין 10 | RE2/CS/AN7 — PORTE bit 2 / Chip select / Analog input 7 |
| פין 11 | VDD — Positive supply voltage |
| פין 12 | VSS — Ground |
| פין 13 | OSC1/CLKIN — Oscillator input / external clock input |
| פין 14 | OSC2/CLKOUT — Oscillator output / clock output |
| פין 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / clock input |
| פין 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 output |
| פין 17 | RC2/CCP1 — PORTC bit 2 / CCP1 output |
| פין 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| פין 19 | RD0/PSP0 — PORTD bit 0 / Parallel Slave Port bit 0 |
| פין 20 | RD1/PSP1 — PORTD bit 1 / Parallel Slave Port bit 1 |
| פין 21 | RD2/PSP2 — PORTD bit 2 / Parallel Slave Port bit 2 |
| פין 22 | RD3/PSP3 — PORTD bit 3 / Parallel Slave Port bit 3 |
| פין 23 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| פין 24 | RC5/SDO — PORTC bit 5 / SPI data out |
| פין 25 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| פין 26 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| פין 27 | RD4/PSP4 — PORTD bit 4 / Parallel Slave Port bit 4 |
| פין 28 | RD5/PSP5 — PORTD bit 5 / Parallel Slave Port bit 5 |
| פין 29 | RD6/PSP6 — PORTD bit 6 / Parallel Slave Port bit 6 |
| פין 30 | RD7/PSP7 — PORTD bit 7 / Parallel Slave Port bit 7 |
| פין 31 | VSS — Ground |
| פין 32 | VDD — Positive supply voltage |
| פין 33 | RB0/INT — PORTB bit 0 / External interrupt |
| פין 34 | RB1 — PORTB bit 1 |
| פין 35 | RB2 — PORTB bit 2 |
| פין 36 | RB3/PGM — PORTB bit 3 / Low-voltage programming |
| פין 37 | RB4 — PORTB bit 4 |
| פין 38 | RB5 — PORTB bit 5 |
| פין 39 | RB6/PGC — PORTB bit 6 / ICSP clock |
| פין 40 | RB7/PGD — PORTB bit 7 / ICSP data |
| פין 41 | NC — Not connected |
| פין 42 | NC — Not connected |
| פין 43 | NC — Not connected |
| פין 44 | NC — Not connected |
יישומים טיפוסיים
PIC16C74B-04/PQ מתאים עבור 6 יישוםs: Industrial Process Control, Motor Drive and PWM Control, Sensor Signal Acquisition, Power Supply Monitoring and Control, Automotive Body Electronics (Legacy), Embedded Data Acquisition Systems.
Industrial Process Control
The PIC16C74B-04/PQ suits industrial process control with its 8-channel 8-bit ADC, which scans multiple analog inputs (temperature, pressure, flow) without an external multiplexer. The 33 digital I/O pins drive relays, solenoids, and indicator LEDs directly via 25 mA sink/source drive strength, eliminating external drivers. Its wide 2.5V-6.0V operating range accepts both regulated 5V logic rails and 24V industrial bus power after regulation. The 7 KB OTP memory holds process loop firmware and PID control tables, while the two CCP modules generate PWM outputs for valve and motor actuator control.
מומלץ
Motor Drive and PWM Control
The PIC16C74B-04/PQ's two Capture/Compare/PWM modules generate complementary PWM outputs for DC motor, stepper, and small BLDC driver stages. With 4 MHz instruction rate and 200 ns cycle time, the MCU achieves 9-bit effective PWM resolution at 20 kHz switching frequency - adequate for brushed motor control and small fan speed regulation. The 25 mA I/O sink/source current directly drives opto-couplers and small gate drivers. Industrial temperature variants (PIC16C74B-04I/PQ) extend deployment to factory-floor enclosures with ambient temperatures above 70C.
מומלץ
Sensor Signal Acquisition
The PIC16C74B-04/PQ's 8-channel 8-bit ADC samples sensor arrays in data acquisition front-ends, supporting thermistor, RTD bridge, and 4-20 mA current loop interfaces through external signal conditioning. The integrated USART streams converted data to a host controller at standard baud rates up to 115.2 kbps, while the MSSP (SPI/I2C) port reads digital sensors and EEPROM calibration tables. Low standby current of 1 µA at 3V makes the part attractive for battery-powered sensor transmitters that sleep between measurement cycles.
מומלץ
Power Supply Monitoring and Control
The PIC16C74B-04/PQ monitors multi-rail power supplies by sampling output voltages with its 8-channel ADC and asserting digital control signals to enable/disable downstream converters. Its wide 2.5V-6.0V supply range allows direct connection to 3.3V or 5V auxiliary rails without level shifting. The USART reports telemetry to a system supervisor via UART, while the two CCP modules provide timing for sequencing power-up of multiple rails. Commercial/industrial temperature grades handle telecom and server-room ambient conditions.
מומלץ
Automotive Body Electronics (Legacy)
The PIC16C74B-04/PQ appears in legacy automotive body modules (interior lighting, seat controllers, instrument cluster drivers) where the 33 I/O pins, 8 ADC channels, and CCP PWM outputs provide sufficient peripheral integration for a single-chip solution. The industrial temperature variant (-40C to +85C or extended -40C to +125C) handles cabin and under-hood thermal stress. While new automotive designs use Flash-based PIC16F or PIC18 families, the OTP PIC16C74B continues in long-life automotive aftermarket and replacement part channels.
מומלץ
Embedded Data Acquisition Systems
The PIC16C74B-04/PQ forms the core of stand-alone data loggers that sample analog inputs, store measurements to external EEPROM via I2C, and transmit accumulated data over USART. The 192-byte RAM buffers sensor samples between ADC conversions, while the 7 KB OTP holds acquisition scheduling and on-the-fly calculations. With 4 MHz operation and 200 ns instruction time, the MCU sustains 8-channel ADC scans at several kHz aggregate rates, suitable for vibration monitoring, HVAC logging, and remote telemetry units.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PIC16C74B-04/PQ — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | PIC16C74B-04I/PQ | PIC16C74BT-04/PQ | PIC16C74A-04/PQ | PIC16C74AT-20I/PQ | PIC16F74-I/PQ |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | MQFP-44 (10x10 mm) | MQFP-44 (10x10 mm) - same | MQFP-44 (10x10 mm) - same | MQFP-44 (10x10 mm) - same | MQFP-44 (10x10 mm) - same | MQFP-44 (10x10 mm) - same |
| Core | 8-bit PIC mid-range | 8-bit PIC mid-range | 8-bit PIC mid-range | 8-bit PIC mid-range | 8-bit PIC mid-range | 8-bit PIC mid-range |
| Maximum Clock | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 20 MHz | 20 MHz |
| Program Memory | 7 KB OTP EPROM | 7 KB OTP EPROM | 7 KB OTP EPROM | 7 KB OTP EPROM | 7 KB OTP EPROM | 7 KB Flash |
| RAM | 192 bytes | 192 bytes | 192 bytes | 192 bytes | 192 bytes | 192 bytes |
| I/O Pins | 33 | 33 | 33 | 33 | 33 | 33 |
| ADC | 8 ch x 8-bit | 8 ch x 8-bit | 8 ch x 8-bit | 8 ch x 8-bit | 8 ch x 8-bit | 8 ch x 8-bit |
| Operating Voltage | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.0 V to 6.0 V |
| Temperature Grade | Commercial (0C to +70C) | Industrial (-40C to +85C) | Commercial (0C to +70C) | Commercial (0C to +70C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) |
מבדילים עיקריים
- Industrial temperature option in same MQFP-44 footprint (לעומתPIC16C74B-04/PQ vs PIC16C74B-04I/PQ)
- Flash reprogrammability for development (לעומתPIC16C74B-04/PQ vs PIC16F74-I/PQ)
- Higher clock speed option for faster execution (לעומתPIC16C74B-04/PQ vs PIC16C74AT-20I/PQ)
הערות תכנון
OTP EPROM memory can be programmed exactly once; a programming error permanently bricks the device. Microchip strongly recommends using the Flash-based PIC16F74 family for prototyping and only converting to PIC16C74B for locked production firmware. Always verify the loaded code via verify-readback before depopulating the programmer socket, and stock sufficient pre-programmed units because each engineering rework consumes a new part.
Place a 100 nF decoupling capacitor within 5 mm of each VDD/VSS pin pair (pins 11/12 and 31/32 on the MQFP-44). Add a 10 µF bulk capacitor at the board's power entry point. The 44-pin MQFP's fine 0.8 mm pitch requires IPC-A-610 Class 2 or 3 assembly with solder paste inspection (SPI) and automated optical inspection (AOI); reflow profile must stay below 250C peak with 60 s above 217C to avoid package delamination.
At 4 MHz with 15 µA typical operating current at 5V, the PIC16C74B-04/PQ dissipates only ~75 µW and requires no special thermal management. However, the 25 mA I/O sink/source current per pin (and 33 pins) can deliver up to 825 mA aggregate if all pins switch simultaneously - verify that the package's 1 W power dissipation limit is respected under worst-case load. For continuous high-current GPIO switching, distribute loads across multiple pins and consider external buffering.
Long parallel PORTD traces to external memory or PSP peripherals benefit from series damping resistors (22-33 ohm) near the MCU to suppress ringing. The MSSP (SPI/I2C) bus requires pull-up resistors on SCL/SDA per I2C specification; for 400 kHz Fast Mode, use 2.2-4.7 kohm pull-ups. Place the crystal oscillator load capacitors (typically 15-33 pF) within 2 mm of OSC1/OSC2 pins (13/14) with a grounded guard ring to attenuate EMI coupling into adjacent ADC channels.
מידע על תאימות
PIC16C74B-04/PQ is generally not lead-free / not RoHS compliant per legacy MQFP package with SnPb lead finish. Industrial-grade -04I variant and Flash-based PIC16F74 family offer RoHS-compliant lead-free options.
