PIC16LF1508-E/SS - 7KB Flash 20MHz XLP MCU 20-SSOP | Microchip
MPN: PIC16LF1508-E/SS ✓ פעילPIC16LF1508-E/SS סקירה
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data memory, and peripherals onto one silicon die. Within the broader taxonomy, the PIC16LF1508 belongs to the microcontrollers family, which itself is a sub-category of integrated circuits (ICs) used for embedded control. XLP (eXtreme Low Power) is Microchip's branding for MCUs optimized for battery-powered applications, featuring nanoWatt sleep currents down to tens of nanoamps. The 'LF' prefix indicates the wide-voltage 'F' process variant rated for 1.8 V to 3.6 V operation.
Key features include 20 MHz CPU speed, brown-out reset, power-on reset, PWM, I2C, SPI, and UART/USART connectivity, plus 10-bit ADC with 12 input channels. The device operates from 1.8 V to 3.6 V (LF variant), with low-power sleep current typically below 50 nA. Enhanced mid-range core supports 49 instructions and 16-level hardware stack.
The PIC16LF1508-E/SS uses an enhanced mid-range 8-bit RISC architecture with 14-bit instruction word, 49 base instructions, and a hardware multiplier. The CLC, NCO, and CWG peripherals enable sensor interface, signal generation, and motor control tasks without CPU intervention, freeing the core for application logic and reducing average power.
Typical applications include battery-powered IoT sensor nodes, low-power wireless remote controls, LED lighting controllers, consumer electronics user interfaces, and portable medical devices. The XLP technology makes it particularly suitable for energy-harvesting and multi-year battery-life products.
When designing with this MCU, ensure decoupling capacitors are placed close to VDD, follow Microchip's recommended ICSP programming connections, and use the MPLAB X IDE with XC8 compiler for development. Consider using the CLC and NCO peripherals to offload timing-critical tasks and reduce active CPU time.
This page synthesizes distributor pricing, drop-in alternative listings, application examples, and practical design notes that complement (rather than duplicate) the manufacturer datasheet, helping engineers evaluate the PIC16LF1508-E/SS for new designs.
חלופות תחליף ישיר עבור PIC16LF1508-E/SS — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם PIC16LF1508-E/SS (אותו גורם צורה וטביעת רגל) — שונים ב Operating Temperature, Package, ADC, Core Architecture, DAC.
PIC16LF1508-I/SS
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PIC16LF1508T-I/SS
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC16F1508-E/SS
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC16LF1508-E/P
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC16LF1507-I/SS
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC16LF1459-E/SS
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC16LF1508-E/SS דירוגים מרביים ומאפיינים חשמליים
| Series | PIC XLP 16F |
| Core Processor | PIC16 |
| Core Size | 8-Bit |
| CPU Speed | 20 MHz |
| Program Memory Size | 7 KB (4K x 14) Flash |
| RAM Size | 256 B |
| Number of I/O | 18 |
| ADC Resolution | 10-bit, 12 channels |
| DAC | 5-bit, 1 channel |
| מתח אספקה | 1.8 V to 3.6 V |
| טמפרטורת פעולה | -40C to +125C |
| מארז | 20-SSOP (0.209 inch / 5.30 mm width) |
| סוג הרכבה | Surface Mount |
| Connectivity | I2C, SPI, UART/USART |
| Peripherals | Brown-out Detect/Reset, POR, PWM, CLC, NCO, CWG |
| סטטוס RoHS | Compliant |
תצורת פינים של PIC16LF1508-E/SS
| פין 1 | RA3/AN3/VREF+/T1G — Bidirectional I/O, analog input 3, voltage reference plus, Timer1 gate |
| פין 2 | RA4/AN4/T1G — Bidirectional I/O, analog input 4, Timer1 gate |
| פין 3 | RA5/MCLR/VPP — Bidirectional I/O, Master Clear (reset), programming voltage |
| פין 4 | RA6/OSC2/CLKOUT — Bidirectional I/O, oscillator output, clock output |
| פין 5 | RA7/OSC1/CLKIN — Bidirectional I/O, oscillator input, clock input |
| פין 6 | VSS — Ground reference |
| פין 7 | RA0/AN0/ICSPDAT — Bidirectional I/O, analog input 0, ICSP data |
| פין 8 | RA1/AN1/ICSPCLK — Bidirectional I/O, analog input 1, ICSP clock |
| פין 9 | RA2/AN2/DACOUT — Bidirectional I/O, analog input 2, DAC output |
| פין 10 | RC0 — Bidirectional I/O port C bit 0 |
| פין 11 | RC1 — Bidirectional I/O port C bit 1 |
| פין 12 | RC2 — Bidirectional I/O port C bit 2 |
| פין 13 | RC3 — Bidirectional I/O port C bit 3 |
| פין 14 | RC4 — Bidirectional I/O port C bit 4 |
| פין 15 | RC5 — Bidirectional I/O port C bit 5 |
| פין 16 | RC6 — Bidirectional I/O port C bit 6 |
| פין 17 | RC7 — Bidirectional I/O port C bit 7 |
| פין 18 | RB4/AN10 — Bidirectional I/O port B bit 4, analog input 10 |
| פין 19 | RB5/AN11 — Bidirectional I/O port B bit 5, analog input 11 |
| פין 20 | VDD — Positive supply voltage (1.8 V to 3.6 V) |
יישומים טיפוסיים
PIC16LF1508-E/SS מתאים עבור 6 יישוםs: Battery-Powered IoT Sensor Node, Low-Power Wireless Remote Control, LED Lighting Controller, Consumer Electronics User Interface, Portable Medical Device Monitoring, Industrial Sensor Interface Module.
Battery-Powered IoT Sensor Node
The PIC16LF1508-E/SS suits battery-powered IoT sensor nodes because its XLP nanoWatt technology delivers sleep currents below 50 nA while retaining RAM, allowing wake-on-interrupt cycles every few seconds for years on a single CR2032 cell. The 12-channel 10-bit ADC with internal voltage reference directly digitizes sensor outputs (temperature, light, motion) without external components. With 7 KB Flash, the device accommodates small Contiki-NG or application-specific sensor fusion code, and the I2C/SPI peripherals connect to common low-power sensors and radio modules like the RN2483 LoRa transceiver.
מומלץ
Low-Power Wireless Remote Control
For handheld remote controls (TV, garage door, industrial keyfob), the PIC16LF1508-E/SS provides a 20 MHz core capable of running RF protocol stacks while its XLP sleep mode extends battery life beyond 5 years on a single coin cell. The 18 I/O pins support matrix keypads up to 4x4, and the CWG/NCO peripherals generate precise carrier frequencies without CPU intervention. The wide 1.8-3.6 V supply range works directly from 2x alkaline or single Li-ion batteries without an LDO.
מומלץ
LED Lighting Controller
The PIC16LF1508-E/SS is well-matched to LED lighting controllers: the 5-bit DAC and 12-bit PWM peripherals generate dimming curves, color mixing, and soft-fade effects with minimal CPU overhead, while the CWG peripheral produces complementary drive signals for half-bridge LED driver topologies. The 12-channel 10-bit ADC reads ambient light sensors and potentiometer inputs for closed-loop dimming. The 1.8 V minimum supply enables direct operation from 2-cell NiMH battery packs in portable fixtures.
מומלץ
Consumer Electronics User Interface
In consumer appliances (coffee makers, air purifiers, fans), the PIC16LF1508-E/SS drives user interfaces with capacitive touch buttons via the CLC peripherals, controls displays over SPI or I2C, and runs motor control loops via PWM. The 20 MHz CPU executes user-interface state machines and basic safety logic, while 7 KB Flash accommodates graphical menu structures. The -40C to +125C extended operating range suits appliance environments near heating elements.
מומלץ
Portable Medical Device Monitoring
For portable medical monitors (pulse oximeters, thermometers, glucose meters), the PIC16LF1508-E/SS provides the precision ADC for biosensor signal acquisition, while the XLP sleep mode extends battery life for patient use. The 5-bit DAC generates bias voltages for sensor front-ends, and the UART enables wired data transfer to host devices. The 1.8 V minimum supply allows direct operation from single-cell alkaline or coin-cell batteries typical of handheld medical devices.
מומלץ
Industrial Sensor Interface Module
In industrial 4-20 mA loop-powered sensor transmitters, the PIC16LF1508-E/SS operates from as low as 1.8 V after the loop sense resistor, providing ADC conversion of bridge sensors, thermistors, or RTDs. The 256-byte SRAM buffers linearization tables, while 7 KB Flash holds calibration coefficients and ModBus RTU protocol stack. The -40C to +125C extended temperature range handles factory-floor environments, and the brown-out reset plus watchdog timer ensure reliable industrial operation.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PIC16LF1508-E/SS — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | PIC16LF1508-I/SS | PIC16LF1508T-I/SS | PIC16F1508-E/SS | PIC16LF1508-E/P | PIC16LF1507-I/SS |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-SSOP | 20-SSOP - same | 20-SSOP - same | 20-SSOP - same | 20-PDIP (through-hole) | 20-SSOP - same |
| Supply Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Flash Memory | 7 KB | 7 KB | 7 KB | 7 KB | 7 KB | 3.5 KB |
| RAM | 256 B | 256 B | 256 B | 256 B | 256 B | 128 B |
| I/O Pins | 18 | 18 | 18 | 18 | 18 | 18 |
| ADC Channels | 12 x 10-bit | 12 x 10-bit | 12 x 10-bit | 12 x 10-bit | 12 x 10-bit | 12 x 10-bit |
| Operating Temperature | -40C to +125C | -40C to +85C | -40C to +85C | -40C to +125C | -40C to +125C | -40C to +85C |
מבדילים עיקריים
- Wide 1.8-3.6 V supply range with XLP nanoWatt sleep (לעומתPIC16F1508-E/SS)
- Extended -40C to +125C operating temperature range (לעומתPIC16LF1508-I/SS)
- On-chip CLC, NCO, and CWG peripherals (לעומתPIC16LF1507-I/SS)
הערות תכנון
For battery-powered designs, use the PIC16LF1508-E/SS sleep mode with peripherals disabled. Per Microchip datasheet section 10, typical sleep current with WDT disabled is 30-50 nA. The on-chip brown-out reset is factory-trimmed; enable BOR in configuration bits for reliable operation across the 1.8-3.6 V range. A 100 nF decoupling capacitor close to VDD (pin 20) plus a 10 uF bulk capacitor is recommended for ADC accuracy.
Place the ICSP programming connector (MCLR/ICSPCLK/ICSPDAT) on the PCB edge or test-point area so that PICkit 4 or MPLAB Snap can be attached without removing the MCU. Keep analog traces (AN0-AN11, VREF+, DACOUT) short and away from switching nodes. Per Microchip layout guidelines, ground the thermal pad (pin 6 VSS) with a wide trace to a low-impedance ground plane for best ADC performance.
Do not apply voltage to RA0/RA1/RA3 during POR when configured as digital inputs without first ensuring VDD is stable - this can cause latch-up. Always configure unused I/O pins as outputs driving low to minimize current leakage. The MCLR pin (RA5/MCLR) requires a 10 kohm pull-up to VDD for normal operation; do not leave it floating. For ADC accuracy, perform a calibration sequence at startup using the internal voltage reference.
מידע על תאימות
RoHS compliant per Microchip product page. PIC16LF1508-E/SS is NOT AEC-Q100 qualified; for automotive applications consult PIC16F1508-E/SS or AEC-Q100-qualified variants.
