PIC18LF24K40-E/SO - 8-bit XLP MCU 16KB Flash 28-SOIC | Microchip
MPN: PIC18LF24K40-E/SO ✓ פעילPIC18LF24K40-E/SO סקירה
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), EEPROM for user data, and a set of analog and digital peripherals around a Harvard architecture core. PIC18 MCUs sit within Microchip's PIC family hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. They are widely deployed where deterministic timing, low power consumption, and small package size matter more than raw compute throughput.
Key features include a 10-bit ADC with Computation (ADCC) supporting Capacitive Voltage Divider (CVD) for advanced touch sensing, a 5-bit DAC, two comparators, PWM, CCP, CWG (Complementary Waveform Generator), HLT (Hardware Limit Timer), Windowed Watchdog Timer (WWDT), CRC/SCAN, Zero-Cross Detection (ZCD), and Peripheral Pin Select (PPS) for flexible signal routing. Communication is provided by EUSART, SPI, and I2C. The XLP core enables typical sleep currents in the nanoamp range.
The PIC18LF24K40 architecture uses an enhanced mid-range 8-bit core with a modified Harvard bus, hardware multiplier, and 31-level hardware stack, supporting C and assembly development under MPLAB X IDE with the XC8 toolchain. PPS allows peripheral signals to be remapped to multiple I/O pins, simplifying PCB layout. The device operates across 1.8 V to 3.6 V (LF variant), making it ideal for 2-cell battery or regulated 3.3 V systems.
Typical applications include battery-powered IoT sensor nodes, capacitive touch user interfaces, low-power remote controls, HVAC sensor transmitters, small home appliances, and industrial sensor conditioning. The combination of ADCC touch support and XLP sleep current suits wearables and energy-harvesting designs.
When designing with this device, allocate adequate decoupling (100 nF plus 1 uF near VDD) and respect the 1.8 V minimum at full speed. Use PPS to optimize pin assignments for the application rather than hardwiring peripherals to multiple PIC pins. For touch electrodes, follow the CVD layout guidelines in the datasheet.
This page synthesizes distributor pricing, parametric comparison, and design notes not found in the manufacturer datasheet alone.
חלופות תחליף ישיר עבור PIC18LF24K40-E/SO — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם PIC18LF24K40-E/SO (אותו גורם צורה וטביעת רגל) — שונים ב ADC, Package, Program Memory (Flash), Communication, Comparators.
PIC18F24K40-E/SO
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC18LF24K40-E/SP
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
PIC18LF25K40-E/SO
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PIC18LF24K40-E/SO דירוגים מרביים ומאפיינים חשמליים
| Product Family | PIC18 (8-bit XLP) |
| Core | PIC18 8-bit enhanced mid-range |
| CPU Speed | 64 MHz (16 MIPS) |
| Program Memory (Flash) | 16 KB (8K x 14) |
| RAM | 1 KB |
| EEPROM | 256 B |
| Supply Voltage (LF) | 1.8 V to 3.6 V |
| ADC | 10-bit with Computation (ADCC), supports CVD touch |
| DAC | 5-bit |
| Comparators | 2 |
| Communication | EUSART, SPI, I2C |
| PWM / CCP / CWG | PWM, CCP, Complementary Waveform Generator |
| Special Peripherals | WWDT, CRC/SCAN, ZCD, PPS, HLT |
| טמפרטורת פעולה | -40C to +125C (E = Extended) |
| מארז | 28-pin SOIC (0.295", 7.50 mm width) |
| סוג הרכבה | Surface Mount |
| סטטוס RoHS | Compliant |
תצורת פינים של PIC18LF24K40-E/SO
| פין 1 | MCLR/RE3 — Master Clear with internal pull-up or digital I/O RE3 |
| פין 2 | RA0 — I/O with analog input |
| פין 3 | RA1 — I/O with analog input |
| פין 4 | RA2 — I/O with analog input |
| פין 5 | RA3 — I/O with analog input |
| פין 6 | RA4 — I/O |
| פין 7 | RA5 — I/O |
| פין 8 | RA6 — I/O |
| פין 9 | RA7 — I/O |
| פין 10 | VSS — Ground reference |
| פין 11 | RB0 — I/O with interrupt-on-change |
| פין 12 | RB1 — I/O with interrupt-on-change |
| פין 13 | RB2 — I/O with interrupt-on-change |
| פין 14 | RB3 — I/O with interrupt-on-change |
| פין 15 | RB4 — I/O with interrupt-on-change |
| פין 16 | RB5 — I/O with interrupt-on-change |
| פין 17 | RB6 — I/O with interrupt-on-change, ICDCLK |
| פין 18 | RB7 — I/O with interrupt-on-change, ICDDAT |
| פין 19 | VSS — Ground reference (second VSS pin) |
| פין 20 | VDD — Positive supply voltage |
| פין 21 | RC0 — I/O |
| פין 22 | RC1 — I/O |
| פין 23 | RC2 — I/O |
| פין 24 | RC3 — I/O |
| פין 25 | RC4 — I/O |
| פין 26 | RC5 — I/O |
| פין 27 | RC6 — I/O |
| פין 28 | RC7 — I/O |
יישומים טיפוסיים
PIC18LF24K40-E/SO מתאים עבור 6 יישוםs: Battery-Powered IoT Sensor Node, Capacitive Touch User Interface, HVAC Sensor Transmitter, Low-Power Remote Control, Industrial Sensor Conditioning, Small Home Appliance Controller.
Battery-Powered IoT Sensor Node
The PIC18LF24K40-E/SO fits battery-powered IoT sensor nodes because its XLP core delivers nanoamp sleep currents and 1.8 V operation allows 2 x AA cells to drain below 2.0 V. The 16 KB Flash hosts a sensor + radio driver stack while the 10-bit ADCC digitizes analog sensors with hardware averaging. The 28-SOIC footprint gives compact PCB integration for sub-coin-cell footprints.
מומלץ
Capacitive Touch User Interface
The PIC18LF24K40-E/SO is purpose-built for capacitive touch UI via its ADCC peripheral implementing Capacitive Voltage Divider (CVD) techniques. Touch buttons, sliders, and proximity wake-on-approach can run with no external touch IC, lowering BOM cost. The 64 MHz core provides responsive scan latency and the 16 KB Flash stores touch firmware and UI state machines.
מומלץ
HVAC Sensor Transmitter
For HVAC sensor transmitters the PIC18LF24K40-E/SO's XLP sleep mode enables multi-year battery life on 2 x AA cells while its 10-bit ADCC digitizes temperature and humidity sensors with hardware oversampling. The 5-bit DAC generates 0-5 V proportional outputs for legacy 4-20 mA loops when used with the F variant, and EUSART connects to wired HVAC bus networks.
מומלץ
Low-Power Remote Control
The PIC18LF24K40-E/SO fits coin-cell-powered remote controls because its nanoamp sleep currents and 1.8 V minimum extend battery life to multi-year horizons. The integrated IR-capable PWM and EUSART drive infrared LEDs directly, while the ADCC supports low-battery voltage monitoring without external ADC chips. PPS remaps peripherals to optimize PCB layout for compact enclosures.
מומלץ
Industrial Sensor Conditioning
For industrial sensor signal conditioning the PIC18LF24K40-E/SO offers 10-bit ADCC for transducer readout, hardware comparators for threshold detection, and ZCD for AC-mains synchronization. The CRC/SCAN peripheral ensures data integrity over noisy factory buses, while SPI/I2C connect to digital sensors or industrial EEPROM. Use the PIC18F24K40-E/SO when 5 V tolerance is required.
מומלץ
Small Home Appliance Controller
The PIC18LF24K40-E/SO drives small home appliances like coffee makers, blenders, and air purifiers because its CWG peripheral generates complementary PWM for motor control, its 5-bit DAC trims analog setpoints, and its compact 28-SOIC fits space-constrained enclosures. The WWDT windowed watchdog provides IEC 60730 safety compliance for Class B appliances.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PIC18LF24K40-E/SO — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | PIC18F24K40-E/SO | PIC18LF24K40-E/SP | PIC18LF25K40-E/SO |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SOIC (0.295") | 28-SOIC (0.295") - same | 28-SPDIP - through-hole | 28-SOIC (0.295") - same |
| Supply Voltage | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Flash | 16 KB | 16 KB | 16 KB | 32 KB |
| RAM | 1 KB | 1 KB | 1 KB | 2 KB |
| CPU Speed | 64 MHz | 64 MHz | 64 MHz | 64 MHz |
| ADC | 10-bit ADCC | 10-bit ADCC | 10-bit ADCC | 10-bit ADCC |
| XLP / Low-Power | Yes (LF variant) | Yes (F variant) | Yes (LF variant) | Yes (LF variant) |
מבדילים עיקריים
- Lowest voltage range in the 28-SOIC PIC18 K40 family (לעומתPIC18F24K40-E/SO)
- Cost-optimized memory vs 25K40 variant (לעומתPIC18LF25K40-E/SO)
- Same die in through-hole package for prototyping (לעומתPIC18LF24K40-E/SP)
הערות תכנון
Place a 100 nF decoupling capacitor as close as possible to the VDD pin (pin 20), with a 1 uF bulk capacitor on the same rail. For battery-powered designs, use the PIC18LF variant's 1.8 V minimum to drain cells below 2.0 V. Configure unused pins as outputs low to minimize leakage current, and route ADC inputs through PPS to allow power-down of unused channels.
Do not operate the PIC18LF24K40 above 64 MHz or below 1.8 V - both violate the LF voltage/frequency derating curve. When migrating to the PIC18F24K40-E/SO ensure the rail voltage is 2.3 V or higher, or the Brown-Out Reset (BOR) will trigger continuously. Use PPS to remap peripherals rather than hardwiring to avoid PCB respins when the firmware demands pin reassignment.
For capacitive touch via the ADCC peripheral, follow the CVD layout guidelines in the datasheet: keep touch traces short, surround them with a hatched ground pour, and route away from switching signals. Add a 10-100 k series resistor on the touch pin to suppress EMI. Use the hardware oversampling feature to improve SNR rather than software averaging to reduce CPU wake time and total energy per scan.
The PIC18LF24K40-E/SO is a low-power CMOS device and thermal management is rarely an issue, but in extended temperature (-40C to +125C) industrial applications verify timing margins with the temperature-voltage derating curves in the datasheet. Above 85C ambient, the maximum CPU frequency decreases; derate accordingly. The 28-SOIC package has good thermal conduction through its leads for moderate-power designs.
מידע על תאימות
RoHS and REACH compliance standard for Microchip PIC18 K40 family. Not AEC-Q100 qualified - select -V (automotive) suffix variants for AEC-Q100.
