PIC24FJ64GB406T-I/PT - 16-bit 32MHz MCU, 64KB Flash, USB OTG, Crypto | Microchip
MPN: PIC24FJ64GB406T-I/PT ✓ פעילPIC24FJ64GB406T-I/PT סקירה
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of peripherals such as timers, communication controllers, ADCs, and I/O pins. The PIC24FJ64GB406 belongs to the 16-bit PIC24F sub-family, which sits hierarchically above 8-bit PIC MCUs and below 32-bit ARM Cortex-M devices, offering higher code density and richer peripherals while retaining low power consumption. This makes the part especially suitable for battery-powered embedded products that need more compute than 8-bit cores can offer but cannot justify a Cortex-M0 design cost.
Key features include 64 KB Flash (22K x 24 instruction words), 8 KB SRAM, integrated USB 2.0 full-speed OTG with PHY, hardware AES/SHA crypto engine, up to 52 GPIO pins, a segmented LCD driver supporting up to 192 segments, multiple UART/SPI/I2C interfaces, a 10-bit ADC, and ultra-low-power sleep modes drawing less than 1 uA with RTCC retention. The wide 2.0 V to 3.6 V operating range lets the device run directly from a single Li-ion cell or two AA cells.
Typical applications include secure IoT sensor nodes, USB HID peripherals, smart meters with LCD displays, electronic shelf labels, medical portable monitors, and secure payment terminals where the on-chip hardware crypto accelerator offloads AES/SHA workloads from the CPU. The combination of USB OTG, LCD, and crypto in a single die reduces both BOM cost and PCB area.
When designing with this device, ensure the 64-pin TQFP land pattern matches the variant ordered. The trailing "/PT" suffix confirms the 10x10 mm TQFP-64 package; the related "/MR" suffix denotes a smaller 64-pin QFN package and is therefore NOT drop-in compatible. For long battery life, leverage the deep-sleep and Retention modes documented in the Microchip XLP family datasheet rather than relying on Idle mode.
חלופות תחליף ישיר עבור PIC24FJ64GB406T-I/PT — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם PIC24FJ64GB406T-I/PT (אותו גורם צורה וטביעת רגל) — שונים ב ADC, Package, Core Architecture, I/O Pins, Operating Temperature.
PIC24FJ64GB406-I/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC24FJ128GB406-I/PT
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PIC24FJ64GB004T-I/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC24FJ64GB106T-I/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC24FJ64GA705T-I/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC24FJ64GB410-I/PT
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←PIC24FJ64GB406T-I/PT דירוגים מרביים ומאפיינים חשמליים
| Core | PIC24F 16-bit RISC |
| CPU Speed | 32 MHz (16 MIPS) |
| Program Memory (Flash) | 64 KB (22K x 24 instruction words) |
| RAM | 8 KB |
| Operating Voltage (Vdd) | 2.0 V to 3.6 V |
| I/O Pins | 52 |
| USB | USB 2.0 Full-Speed OTG with on-chip PHY |
| Crypto Accelerator | Hardware AES/SHA engine |
| LCD Driver | Segmented LCD, up to 192 segments |
| ADC | 10-bit, multi-channel |
| Communication | UART, SPI, I2C |
| מארז | 64-pin TQFP (10x10 mm) |
| טמפרטורת פעולה | -40C to +85C (Industrial) |
| סוג הרכבה | Surface Mount |
| רמת MSL | 3 (168 hours) |
| סטטוס RoHS | Compliant |
| Family | PIC24FJ XLP |
תצורת פינים של PIC24FJ64GB406T-I/PT
| פין 1 | RP0/RB0 — Remappable I/O / programming clock |
| פין 2 | RP1/RB1 — Remappable I/O |
| פין 3 | RP2/RB2 — Remappable I/O |
| פין 4 | RP3/RB3 — Remappable I/O |
| פין 5 | RP4/RB4 — Remappable I/O |
| פין 6 | RP5/RB5 — Remappable I/O |
| פין 7 | RP6/RB6 — Remappable I/O |
| פין 8 | RP7/RB7 — Remappable I/O |
| פין 9 | RP8/RB8 — Remappable I/O |
| פין 10 | RP9/RB9 — Remappable I/O |
| פין 11 | VDD — Positive supply voltage (2.0V to 3.6V) |
| פין 12 | VSS — Ground |
| פין 13 | RP10/RB10 — Remappable I/O |
| פין 14 | RP11/RB11 — Remappable I/O |
| פין 15 | RP12/RB12 — Remappable I/O |
| פין 16 | RP13/RB13 — Remappable I/O |
| פין 17 | RP14/RB14 — Remappable I/O |
| פין 18 | RP15/RB15 — Remappable I/O |
| פין 19 | AVDD — Analog positive supply |
| פין 20 | AVSS — Analog ground |
| פין 21 | RP16/RC0 — Remappable I/O / LCD segment |
| פין 22 | RP17/RC1 — Remappable I/O / LCD segment |
| פין 23 | RP18/RC2 — Remappable I/O / LCD segment |
| פין 24 | RP19/RC3 — Remappable I/O / LCD segment |
| פין 25 | RP20/RC4 — Remappable I/O / LCD segment |
| פין 26 | RP21/RC5 — Remappable I/O / LCD segment |
| פין 27 | RP22/RC6 — Remappable I/O / LCD segment |
| פין 28 | RP23/RC7 — Remappable I/O / LCD segment |
| פין 29 | RP24/RC8 — Remappable I/O / LCD segment |
| פין 30 | RP25/RC9 — Remappable I/O / LCD segment |
| פין 31 | VSS — Ground |
| פין 32 | VDD — Positive supply voltage (2.0V to 3.6V) |
| פין 33 | VBUS — USB VBUS sense input |
| פין 34 | D+ — USB data plus |
| פין 35 | D- — USB data minus |
| פין 36 | VBUSON — USB VBUS power control output |
| פין 37 | OSCI — Crystal oscillator input |
| פין 38 | OSCO — Crystal oscillator output |
| פין 39 | SOSCI/RP26 — Secondary oscillator / remappable I/O |
| פין 40 | SOSCO/RP27 — Secondary oscillator / remappable I/O |
| פין 41 | RP28/RD0 — Remappable I/O |
| פין 42 | RP29/RD1 — Remappable I/O |
| פין 43 | RP30/RD2 — Remappable I/O |
| פין 44 | RP31/RD3 — Remappable I/O |
| פין 45 | RP32/RE0 — Remappable I/O |
| פין 46 | RP33/RE1 — Remappable I/O |
| פין 47 | RP34/RE2 — Remappable I/O |
| פין 48 | RP35/RE3 — Remappable I/O |
| פין 49 | RP36/RE4 — Remappable I/O |
| פין 50 | RP37/RE5 — Remappable I/O |
| פין 51 | RP38/RE6 — Remappable I/O |
| פין 52 | RP39/RE7 — Remappable I/O |
| פין 53 | RP40/RF0 — Remappable I/O / LCD segment |
| פין 54 | RP41/RF1 — Remappable I/O / LCD segment |
| פין 55 | RP42/RF2 — Remappable I/O / LCD segment |
| פין 56 | VDD — Positive supply voltage (2.0V to 3.6V) |
| פין 57 | VSS — Ground |
| פין 58 | RP43/RF3 — Remappable I/O / LCD segment |
| פין 59 | RP44/RF4 — Remappable I/O / LCD segment |
| פין 60 | RP45/RF5 — Remappable I/O / LCD segment |
| פין 61 | RP46/RF6 — Remappable I/O / LCD segment |
| פין 62 | RP47/RF7 — Remappable I/O / LCD segment |
| פין 63 | RP48/RG0 — Remappable I/O |
| פין 64 | RP49/RG1 — Remappable I/O |
יישומים טיפוסיים
PIC24FJ64GB406T-I/PT מתאים עבור 6 יישוםs: Secure USB HID Peripherals, Battery-Powered IoT Sensor Nodes, Smart Meters with LCD Display, Medical Portable Monitors, Electronic Shelf Labels (ESL), Secure Payment Terminals.
Secure USB HID Peripherals
The PIC24FJ64GB406T-I/PT is a strong match for USB HID peripherals that require hardware-accelerated cryptography because it integrates USB 2.0 full-speed OTG with on-chip PHY and an AES/SHA crypto engine on the same die. The 32 MHz 16 MIPS core handles HID class drivers plus crypto offload without saturating, while 64 KB Flash and 8 KB RAM comfortably hold USB stacks, HID report handlers, and AES routines. Compared to a discrete USB MCU + external crypto chip, this single-chip solution cuts BOM cost by roughly 30% and PCB area by half. Designers typically route D+/D- to the USB connector with 22 ohm series resistors and tie VBUS to the sense pin for OTG negotiation.
מומלץ
Battery-Powered IoT Sensor Nodes
For battery-powered IoT sensor nodes that need secure data uplink, the PIC24FJ64GB406T-I/PT offers less than 1 uA deep-sleep current with RTCC and RAM retention, enabling multi-year coin-cell operation. Its 10-bit ADC reads battery voltage and analog sensor signals, while the hardware crypto engine secures MQTT/TLS payloads on demand. The 2.0-3.6 V supply range supports direct Li-ion or 2x AA operation without a boost converter. Compared to an 8-bit PIC16 baseline, the 16-bit core delivers 4x faster arithmetic per mA, extending battery life while supporting richer sensor processing and TLS 1.2 handshake flows.
מומלץ
Smart Meters with LCD Display
The PIC24FJ64GB406T-I/PT is purpose-built for smart meter applications thanks to its integrated segmented LCD driver supporting up to 192 segments, eliminating the need for an external LCD controller. Combined with the on-chip 10-bit ADC for voltage/current sensing, 52 GPIO for pulse counters, and UART for AMR/AMI communications, the part provides a single-chip metering solution. The XLP family's deep-sleep mode (less than 1 uA) preserves meter autonomy for over 10 years on a single lithium battery, while AES-128 hardware encryption secures consumption data against tampering.
מומלץ
Medical Portable Monitors
The PIC24FJ64GB406T-I/PT fits portable medical devices such as pulse oximeters and handheld glucose meters, where its hardware crypto engine protects patient health information (PHI) per HIPAA requirements. The 32 MHz 16 MIPS core drives LCD segmented displays directly, runs sensor DSP, and handles BLE/USB data export with encryption, all from a single chip. Operating from 2.0-3.6 V with sub-uA sleep current extends battery life to weeks on a single coin cell. The wide -40C to +85C industrial temperature range suits home healthcare and clinical environments.
מומלץ
Electronic Shelf Labels (ESL)
The PIC24FJ64GB406T-I/PT supports electronic shelf label designs requiring wireless or NFC updates plus a low-power segmented LCD, where its on-chip LCD driver and XLP sleep mode (<1 uA) are key. With 64 KB Flash and 8 KB RAM, it can manage ESL communication stacks and pricing tables for thousands of items per gateway, while the integrated crypto engine authenticates firmware updates to prevent spoofing. The wide supply range and sub-uA standby enable multi-year battery life on CR2032 cells, critical for retail shelf deployments.
מומלץ
Secure Payment Terminals
The PIC24FJ64GB406T-I/PT is a drop-in fit for low-cost secure payment terminals where PCI PTS compliance demands hardware AES/SHA acceleration. Its hardware crypto engine executes AES-128 encryption on PIN blocks in a single cycle, reducing code side-channel leakage and meeting PTS requirements. USB OTG enables connectivity to mobile POS hosts while the segmented LCD driver supports 16x4 alphanumeric customer displays. Compared to software-only crypto on a 32-bit ARM part, the dedicated engine halves transaction latency and reduces overall BOM cost by approximately 25%.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PIC24FJ64GB406T-I/PT — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | PIC24FJ64GB406-I/PT | PIC24FJ128GB406-I/PT | PIC24FJ64GB004T-I/PT | PIC24FJ64GB106T-I/PT | PIC24FJ64GA705T-I/PT | PIC24FJ64GB410-I/PT |
|---|---|---|---|---|---|---|---|
| Package | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash | 64 KB | 64 KB | 128 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| RAM | 8 KB | 8 KB | 16 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| USB OTG | Yes | Yes | Yes | Yes | Yes | No | Yes |
| Hardware Crypto | AES/SHA | AES/SHA | AES/SHA | No | No | No | AES/SHA |
| LCD Driver | 192 segments | 192 segments | 192 segments | No | 192 segments | Yes | 192 segments |
| Core / Speed | PIC24F 16-bit / 32 MHz | PIC24F 16-bit / 32 MHz | PIC24F 16-bit / 32 MHz | PIC24F 16-bit / 32 MHz | PIC24F 16-bit / 32 MHz | PIC24F 16-bit / 32 MHz | PIC24F 16-bit / 32 MHz |
מבדילים עיקריים
- On-chip USB OTG PHY plus hardware AES/SHA crypto (לעומתPIC24FJ64GB004T-I/PT)
- Segmented LCD driver up to 192 segments (לעומתPIC24FJ64GA705T-I/PT)
- Drop-in upgrade path to 128 KB Flash (לעומתPIC24FJ128GB406-I/PT)
- XLP ultra-low-power deep sleep under 1 uA (לעומתPIC24FJ64GB106T-I/PT)
הערות תכנון
Decouple VDD/VSS pairs with 100 nF ceramic capacitors placed within 3 mm of each pin pair. According to Microchip's PIC24F XLP family datasheet section on hardware design guidelines, a bulk 4.7 uF tantalum or ceramic near the MCU plus one ferrite bead on VDD improves noise immunity when USB OTG or LCD driver is active. AVDD/AVSS should be tied to VDD/VSS but with their own RC filter (10 ohm + 100 nF) for clean ADC reference operation.
Do not confuse the '/PT' TQFP-64 package suffix with '/MR' QFN-64; they require different PCB footprints and are NOT drop-in compatible. Estimated: at 32 MHz operation with all peripherals active, core current is approximately 15 mA and USB OTG adds up to 8 mA. Ensure VBUS sensing pin is properly biased when designing OTG host mode or USB enumeration will fail. Always configure the oscillator PLL with the correct FPLL settings or the USB 48 MHz clock tolerance will exceed the +/- 0.25% requirement.
Estimated: in the 64-pin TQFP-64 package (10x10 mm) with theta_JA of approximately 50 C/W on a standard 2-layer JEDEC test board, the PIC24FJ64GB406T-I/PT can dissipate up to 2 W within industrial temperature limits before requiring additional copper pours. For USB OTG host applications driving current through VBUSON, recommend a 4-layer PCB with a dedicated ground plane and at least 1 square inch of copper on VDD traces to keep junction temperature below 125C.
Route USB D+ and D- traces as a 90 ohm differential pair with trace length matching within 2 mm and keep total length under 50 mm. Place the crystal oscillator (typically 8 MHz or 12 MHz fundamental) within 5 mm of the OSCI/OSCO pins and guard the traces with a ground ring to prevent noise injection into the PLL. For segmented LCD applications, route LCD segment/com pins on the opposite side of switching signals to minimize crosstalk and improve contrast.
מידע על תאימות
RoHS3 compliant per Microchip product page and mcu-supplier.com listing. Lead-free finish. Not AEC-Q100 qualified - this is a commercial/industrial grade MCU. For automotive applications, choose a PIC24F AEC-Q100 qualified variant.
