TDA38827AUMA1 - 25A OptiMOS IPOL Buck Regulator | Infineon
MPN: TDA38827AUMA1 ✓ פעילTDA38827AUMA1 סקירה
A buck regulator is a switch-mode DC-DC converter that steps a higher input voltage down to a lower regulated output voltage with high efficiency. Within the power management hierarchy, a buck converter belongs to the broader family of switching regulators, which sit alongside linear regulators (LDOs) and charge pumps in the DC-DC converter category. Integrated POL (point-of-load) regulators such as the TDA38827 incorporate the controller, FETs, and often bootstrap drive into one IC, eliminating external MOSFETs and shrinking board area versus discrete buck designs.
Key specifications include 25 A continuous output current, 0.6 V minimum adjustable output, constant on-time (COT) control for fast transient response, and integrated OptiMOS 5 FETs with built-in bootstrap diode. The COT architecture provides pseudo-fixed switching frequency, near-unity duty ratio operation at heavy load, and inherently stable output without external compensation network. The 22-pin PowerVQFN package (PG-IQFN-22) exposes a thermal pad that conducts heat from the integrated MOSFETs to the PCB copper pour.
Typical applications include server and datacom POL rails, telecom card voltage rails, distributed bus converters in storage and networking hardware, FPGA/DSP core and I/O supplies, and high-current ASIC power delivery. The combination of 25 A capability and a compact package suits space-constrained boards where designers need high current density and reduced BOM count.
When designing with this part, follow Infineon's recommended input/output capacitor values and observe the thermal pad layout guidelines. The COT control scheme depends on the output ripple for stable switching, so external ripple injection or a low-ESR output capacitor network may be required in some configurations.
חלופות תחליף ישיר עבור TDA38827AUMA1 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם TDA38827AUMA1 (אותו גורם צורה וטביעת רגל) — שונים ב Package.
TDA38826XUMA1
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TDA38827
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TDA38827AUMA1 דירוגים מרביים ומאפיינים חשמליים
| טופולוגיה | Synchronous Buck (Step-Down) |
| סוג פלט | Adjustable |
| Minimum Output Voltage | 0.6 V |
| מספר יציאות | 1 |
| זרם מוצא מקסימלי | 25 A |
| Control Scheme | Constant On-Time (COT) |
| Integrated Power Stage | OptiMOS 5 MOSFETs with integrated bootstrap diode |
| מארז | 22-PowerVQFN (PG-IQFN-22) |
| סוג הרכבה | Surface Mount |
| Switching Behavior | PWM, constant on-time |
| פונקציה | Integrated Point-of-Load (POL) DC-DC Buck Regulator |
| Product Family | OptiMOS IPOL |
| סטטוס RoHS | Compliant |
תצורת פינים של TDA38827AUMA1
| פין 1 | VIN — Input supply voltage |
| פין 2 | VIN — Input supply voltage |
| פין 3 | PGND — Power ground |
| פין 4 | PGND — Power ground |
| פין 5 | SW — Switch node (phase output to inductor) |
| פין 6 | SW — Switch node (phase output to inductor) |
| פין 7 | VCC — Internal regulator output / bootstrap supply |
| פין 8 | BOOT — Bootstrap pin for high-side gate drive |
| פין 9 | VOUT — Output voltage sense / return path |
| פין 10 | FB — Feedback (to external resistor divider) |
| פין 11 | EN — Enable input |
| פין 12 | AGND — Analog ground |
| פין 13 | NC — Not connected (per datasheet) |
| פין 14 | NC — Not connected (per datasheet) |
| פין 15 | NC — Not connected (per datasheet) |
| פין 16 | NC — Not connected (per datasheet) |
| פין 17 | PGND — Power ground |
| פין 18 | PGND — Power ground |
| פין 19 | VIN — Input supply voltage |
| פין 20 | VIN — Input supply voltage |
| פין 21 | PGND — Power ground |
| פין 22 | PGND — Power ground |
יישומים טיפוסיים
TDA38827AUMA1 מתאים עבור 6 יישוםs: Server and Datacom Point-of-Load Rails, Telecom Card Voltage Rails, FPGA Core and I/O Voltage Supplies, High-Current ASIC Power Delivery, Industrial Distributed Bus Conversion, Storage Controller Board Power.
Server and Datacom Point-of-Load Rails
The TDA38827AUMA1's 25 A continuous output and integrated OptiMOS 5 power stage make it well-suited for high-current POL rails on server motherboards, where it typically delivers 1.0 V to 1.8 V to ASIC and memory loads from a 12 V intermediate bus. Its constant on-time control scheme provides sub-microsecond transient response to sudden load steps from CPUs and switch fabrics, while the 22-pin PowerVQFN footprint reduces board area versus discrete controller-plus-FET solutions.
מומלץ
Telecom Card Voltage Rails
In telecom line cards and baseband units, the TDA38827AUMA1 powers high-current DSP and FPGA cores directly from the 12 V or 5 V distribution bus. The integrated bootstrap diode and OptiMOS 5 FETs remove the need for an external high-side driver, cutting BOM count by several parts per rail. The COT control inherently adapts the on-time to input voltage variation, which is helpful on telecom boards that experience bus transients during hot-swap events.
מומלץ
FPGA Core and I/O Voltage Supplies
The TDA38827AUMA1's adjustable output down to 0.6 V matches the core voltage of most modern FPGAs and SoCs, while its 25 A capability can supply even large FPGA core rails from a single chip. Designers can use one TDA38827AUMA1 per core rail and a second for the I/O voltage, simplifying multi-rail sequencing. The fast transient response of the COT loop keeps Vcore within tolerance during logic-block switching surges that occur at every clock edge.
מומלץ
High-Current ASIC Power Delivery
Networking ASICs and switch-fabric chips often demand 15-25 A at sub-1 V rails, exactly the operating envelope of the TDA38827AUMA1. The integrated power stage keeps the high-current switching loop small, which reduces parasitic inductance and limits voltage overshoot at the load. Using the TDA38827AUMA1 instead of a discrete buck halves the number of power components on the bill of materials and simplifies thermal design.
מומלץ
Industrial Distributed Bus Conversion
In industrial 24 V or 12 V distributed bus systems, the TDA38827AUMA1 serves as the local POL converter stepping down to logic-level rails for motor controllers, PLCs, and I/O modules. Its PowerVQFN exposed thermal pad couples directly to inner-layer copper planes, which is important when the converter sits inside a sealed enclosure with limited airflow. The COT scheme also tolerates the wide input voltage variation typical of industrial DC buses.
מומלץ
Storage Controller Board Power
Enterprise SSD and HDD controller boards require tightly regulated 1.0 V to 3.3 V rails for the main storage controller, DRAM, and NAND interface. The TDA38827AUMA1's 25 A rating and small footprint suit the dense layout of NVMe controller cards, while its high efficiency from integrated OptiMOS 5 FETs keeps thermal rise low even at full load. Multiple TDA38827AUMA1 devices can be paralleled or assigned to different rails on the same controller board.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TDA38827AUMA1 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TDA38826XUMA1 |
|---|---|---|
| Package | 22-PowerVQFN (PG-IQFN-22) | 22-PowerVQFN (PG-IQFN-22) |
| Brand | Infineon | Infineon |
| Maximum Output Current | 25 A | 12-15 A |
| Control Scheme | Constant On-Time (COT) | Constant On-Time (COT) |
| Integrated MOSFETs | OptiMOS 5 (HS + LS) | OptiMOS 5 (HS + LS) |
| Integrated Bootstrap Diode | Yes | Yes |
| Drop-in Replacement | — | Lower current only |
מבדילים עיקריים
- 25 A in a single integrated power stage (לעומתTDA38826XUMA1)
- OptiMOS 5 FETs integrated with bootstrap diode (לעומתDiscrete controller + external FETs)
- COT control without external compensation (לעומתVoltage-mode controllers with compensation network)
הערות תכנון
The 22-pin PowerVQFN package relies on the exposed thermal pad to conduct heat from the integrated OptiMOS 5 FETs into the PCB copper. Use at least 4 thermal vias in the pad, stitch the inner copper layers with copper pours, and place the input ceramic capacitors directly above the high-current VIN/PGND pairs to minimize loop resistance and improve heat spreading. Estimated: at 12 V to 1.0 V and 25 A, efficiency is approximately 90-92%, leading to roughly 2-3 W of dissipation that must be sunk through the PCB.
Place the input ceramic capacitors as close as possible to the VIN and PGND pins, with the high-side FET loop area (VIN — HS-FET — SW — LS-FET — PGND) kept to a minimum. The SW node to inductor connection should be wide and short. The exposed thermal pad must be soldered to a copper plane of at least 1 oz copper for adequate thermal performance. Recommended footprint dimensions are provided in the Infineon OptiMOS IPOL land pattern.
The COT control scheme requires sufficient output ripple at the feedback node to set a stable switching frequency. With all-ceramic low-ESR output capacitors, an external ripple injection network (feedforward from VOUT or SW) may be required — omitting it can cause sub-harmonic instability. Always verify the design with the Infineon reference design BOM and follow the recommended inductor and output capacitor values.
מידע על תאימות
RoHS and REACH compliance per Infineon product page. AEC-Q100 not applicable — this is an industrial/commercial OptiMOS IPOL regulator, not an automotive-qualified part.
