TS3704CN - Micropower Quad CMOS Comparator | STMicroelectronics
MPN: TS3704CN ✗ סוף ייצורTS3704CN סקירה
A voltage comparator is an analog semiconductor that compares an input voltage with a reference or threshold and changes its output when the relationship between those voltages changes. The TS3704 belongs to the comparator hierarchy within integrated circuits and analog signal conditioning. Compared with the bipolar LM339 family, its CMOS implementation consumes substantially less current and uses push-pull outputs, eliminating the external pull-up resistor normally required by open-collector comparators.
The principal features of the TS3704CN include four CMOS comparator channels, 9 µA typical current consumption per comparator, a fast response time of 2 µs typical for a 5 mV overdrive, and typical input impedance of 10^12 ohms. Its push-pull output stage can drive logic inputs directly while reducing external component count. The device is also described as pin-to-pin and functionally compatible with the bipolar LM339, although output polarity, common-mode limits, supply behavior, and timing should still be checked before substitution.
The TS3704 architecture supports four independent threshold or window-detection functions in one package. High input impedance reduces loading on high-impedance sensor nodes, while the low 9 µA typical consumption per comparator suits battery-operated equipment. The 2 µs typical response is useful for systems requiring fast decisions without moving to a higher-power comparator family. Its through-hole DIP-14 construction also favors legacy industrial, instrumentation, and educational designs where socketed or leaded assembly is preferred.
Typical uses include battery-powered sensor interfaces, overvoltage and undervoltage detection, industrial control thresholds, window comparators, and low-power monitoring systems. The TS3704CN is particularly appropriate when one board requires several independent comparisons and when avoiding open-collector pull-up components materially simplifies the design.
Designers should account for input common-mode range, supply voltage, output drive, and input overvoltage before assigning comparator inputs. Because this is a leaded DIP device, board spacing, soldering heat, and cleaning practices also affect long-term assembly reliability. Decoupling should follow the manufacturer datasheet guidance, especially when long PCB traces or switching sources are present.
This product record combines the manufacturer datasheet, distributor identification, explicit package information, cross-reference candidates, and practical engineering guidance to support component selection, replacement assessment, PCB planning, and low-power comparator design.
חלופות תחליף ישיר עבור TS3704CN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
TLC3704CN
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLC3704CNE4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
NJU7104AM-TE1
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TS3704CN דירוגים מרביים ומאפיינים חשמליים
| Comparator Type | General-purpose voltage comparator |
| Number of Comparators | 4 channels |
| Technology | CMOS |
| סוג פלט | Push-pull CMOS |
| Supply Current per Comparator | 9 µA typical |
| Response Time | 2 µs typical for 5 mV overdrive |
| Input Impedance | 10^12 ohms typical |
| מארז | 14-pin DIP |
| מספר פינים | 14 pins |
| סוג הרכבה | Through-hole |
| External Pull-Up Resistor | Not required for push-pull output |
| LM339 Compatibility | Pin-to-pin and functionally compatible |
תצורת פינים של TS3704CN
| פין 1 | OUT1 — Comparator 1 push-pull output |
| פין 2 | IN1- — Comparator 1 inverting input |
| פין 3 | IN1+ — Comparator 1 non-inverting input |
| פין 4 | VCC — Positive supply connection |
| פין 5 | IN2+ — Comparator 2 non-inverting input |
| פין 6 | IN2- — Comparator 2 inverting input |
| פין 7 | OUT2 — Comparator 2 push-pull output |
| פין 8 | OUT3 — Comparator 3 push-pull output |
| פין 9 | IN3- — Comparator 3 inverting input |
| פין 10 | IN3+ — Comparator 3 non-inverting input |
| פין 11 | GND — Ground connection |
| פין 12 | IN4+ — Comparator 4 non-inverting input |
| פין 13 | IN4- — Comparator 4 inverting input |
| פין 14 | OUT4 — Comparator 4 push-pull output |
יישומים טיפוסיים
TS3704CN מתאים עבור 6 יישוםs: Battery-Powered Threshold Monitoring, Industrial Overvoltage Detection, Sensor Signal Conditioning, Window Comparator Control, Instrumentation and Test Equipment, Legacy Control Board Retrofit.
Battery-Powered Threshold Monitoring
The TS3704CN fits battery-powered equipment that must monitor several supply or signal thresholds while keeping standby consumption low. Each of its four CMOS comparator channels draws 9 µA typical, allowing a single 14-DIP package to supervise multiple rails instead of requiring four separate comparator ICs. The 10^12-ohm typical input impedance also minimizes loading on high-impedance sensor nodes. In a portable monitor, two channels can define an upper and lower window while the other channels supervise additional rails. Designers should confirm the valid input common-mode range and supply limits for the minimum battery voltage, then add hysteresis where the monitored signal crosses the threshold slowly.
מומלץ
Industrial Overvoltage Detection
The TS3704CN is useful in industrial control boards that must detect excessive or insufficient voltage on several protected rails. Its four independent channels provide separate decisions, while the 2 µs typical response for a 5 mV overdrive supports prompt fault signaling. Push-pull outputs can directly drive a downstream logic input without the pull-up resistor commonly required by open-collector implementations. In a protection circuit, scale the monitored voltage into the permitted input range, establish deliberate hysteresis to prevent repeated switching, and route the output to a shutdown latch. Verify operating temperature, input tolerance, and output levels against the industrial system requirements before release.
מומלץ
Sensor Signal Conditioning
The TS3704CN can condition high-impedance sensor outputs by comparing a conditioned signal with an adjustable reference. Its 10^12-ohm typical input impedance helps preserve weak sensor signals, while the micropower 9 µA-typical-per-channel consumption suits battery-operated sensing. A typical arrangement places the sensor output on one input, a resistor-divider reference on the other, and uses positive feedback for hysteresis. The push-pull output then provides a logic-level indication without a discrete pull-up resistor. The 2 µs typical response is appropriate for many low-frequency sensor systems, although input offset, common-mode range, noise around the threshold, and propagation delay must be checked in the complete signal chain.
מומלץ
Window Comparator Control
The TS3704CN supports window-comparator functions in which two thresholds determine whether a monitored voltage is above, below, or within an accepted range. Two channels can be assigned to the upper and lower limits, and additional channels can supervise related signals. The 9 µA typical consumption per comparator is particularly helpful in continuously powered monitoring equipment, while the 2 µs typical response for a 5 mV overdrive allows rapid transitions. Implement each comparison with a resistor divider and controlled feedback to set hysteresis. Confirm that both references remain inside the comparator’s allowed common-mode range and that the supply remains valid during power transitions, since either condition can create false state changes.
מומלץ
Instrumentation and Test Equipment
The TS3704CN fits legacy instrumentation designs that require several low-power decision points rather than a single precision comparison channel. The four-channel DIP package simplifies through-hole assembly and can implement range detection, limit alarms, and control-signal translation. Its push-pull output stage removes the need for open-collector pull-up components and can reduce board population in older control boards. For measurement systems, compare the comparator’s input offset and response behavior with the required measurement accuracy, and add external filtering if noisy signals can switch near the threshold. The 14-DIP footprint is particularly convenient when maintaining an existing through-hole analog board.
מומלץ
Legacy Control Board Retrofit
The TS3704CN is appropriate for maintaining or restoring a legacy 14-DIP control board that originally used four open-collector comparator functions. Because the TS3704 offers push-pull CMOS outputs, existing pull-up networks can often be removed after confirming that the destination logic accepts the resulting output levels. The 9 µA typical current per comparator supports low-power operation, while the 2 µs typical response for a 5 mV overdrive is adequate for many control events. Before retrofitting, compare supply polarity, input common-mode range, threshold polarity, and logic state at power-up. The original board layout and component values should be treated as the authority for the physical connection.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TS3704CN — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TLC3704CN | TLC3704CNE4 | NJU7104AM-TE1 |
|---|---|---|---|---|
| Package | DIP-14 | DIP-14 | DIP-14 | DIP-14 |
| Brand | STMicroelectronics | Texas Instruments | Texas Instruments | JRC |
מבדילים עיקריים
- Low quiescent consumption in a four-channel package (לעומתTLC3704CN)
- Push-pull output avoids an external pull-up resistor (לעומתNJU7104AM-TE1)
- Fast low-overdrive response (לעומתTLC3704CNE4)
הערות תכנון
Budget the four channels at 36 µA of typical comparator supply current before adding input bias, reference-divider, and leakage currents. This is an estimate based on the datasheet value of 9 µA typical per comparator. The actual board current can differ with supply voltage, input voltage, output state, and process variation, so measure the complete assembled circuit across its operating range.
Keep comparator input traces short and route them away from switching nodes and high-current edges. The 10^12-ohm typical input impedance reduces loading, but it does not prevent interference from nearby signals. Use a grounded guard or shielding strategy for very high-impedance nodes, and place the feedback resistors used for hysteresis close to the relevant input pins.
Do not treat LM339 compatibility as permission to ignore the TS3704CN supply and common-mode limits. Confirm polarity, valid input range, output levels, and startup behavior against the manufacturer datasheet. Push-pull outputs may allow pull-up resistors to be omitted, but existing networks should not be removed until the destination device’s input thresholds and output leakage requirements have been checked.
Provide stable supply decoupling close to the DIP pins and avoid long supply loops through the board. Although the comparator consumes little current, supply transients can move the threshold or cause an output transition. For through-hole assembly, maintain adequate spacing from heat sources and inspect joints for adequate wetting because repeated thermal cycles can stress large DIP leads.
מידע על תאימות
No product-specific environmental or material compliance declarations were identified. AEC-Q100 is not applicable to this general-purpose comparator application.