USB2228-NU-05 - USB 2.0 Flash Media Controller | Microchip
MPN: USB2228-NU-05 ✓ פעילUSB2228-NU-05 סקירה
A USB flash media controller is a type of USB interface controller that bridges a USB host and one or more flash-card formats. In the product hierarchy, it belongs to interface controllers, then USB controllers, then integrated circuits and semiconductors. Rather than implementing flash-card protocol conversion in a system controller, the USB2228 provides dedicated interface circuitry and on-chip firmware for communicating with supported removable media. This division of responsibility can simplify host-side software and reduce the electrical burden on a general-purpose embedded processor.
The fourth-generation controller supports USB 2.0 operation with a parallel interface. Its 3 V to 3.6 V operating-supply range is suitable for systems using a regulated 3.3 V rail. The listed 75 mA supply current provides a baseline for power budgeting, although application-specific current can vary with operating state and attached media. Integrated card-power FETs are identified in the product description, allowing the controller to manage card-power signaling in designs using the supported flash-card interfaces.
The USB2228 is designed for compact removable-media systems rather than general-purpose USB peripherals. Its supported media families include xD-Picture Card, SmartMedia, Memory Stick, High Speed Memory Stick, and Memory Stick PRO. On-chip firmware reads and writes High Speed Memory Stick and MS PRO media, as stated in the USB2227/USB2228 datasheet. The 128-pin VTQFP provides the mixed-signal, power, logic, and media-interface connections required by this multi-format controller.
Typical uses include legacy USB card readers, portable media adapters, multifunction peripherals, and embedded systems requiring removable flash-media access. The controller is most appropriate when an existing USB host must interoperate with one of the explicitly supported card formats. Software and PCB validation are necessary before adopting this controller in a new design because support for newer SD, CF, or USB flash media is not established by the provided sources.
Designers should verify the exact pin assignments, clock requirements, media-connector routing, card-power limits, and host-driver support against the manufacturer datasheet. The 14 mm by 14 mm VTQFP also requires a 128-lead PCB land pattern and careful signal-integrity review of parallel and USB interfaces. The provided data does not expose individual pin names, so no pin-level assignments are asserted in this record.
This page consolidates verified manufacturer and distributor information, distinguishes confirmed USB 2.0, voltage, package, current, and media-support facts from unspecified parameters, and provides drop-in alternatives with their sourcing limits documented. It is intended to support engineering selection while avoiding unsupported claims about pinout, pricing, lifecycle transitions, or unlisted electrical characteristics.
חלופות תחליף ישיר עבור USB2228-NU-05 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם USB2228-NU-05 (אותו גורם צורה וטביעת רגל) — שונים ב Integrated Card Power FETs.
USB2228-NU-05-E2
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
USB2228-NU-05-E6
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
USB2227-NU-05
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←USB2251-NU-05
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
USB2228-NU-05-E2C
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
USB2228-NU-05 מפרטים
| Controller Type | USB 2.0 Controller |
| Host Interface | Parallel |
| Supply Voltage Range | 3 V to 3.6 V |
| זרם אספקה | 75 mA |
| מארז | 128-pin VTQFP (14 mm x 14 mm) |
| Media Interface | Flash media card controller |
| xD-Picture Card Support | Supported |
| SmartMedia Support | Supported |
| Memory Stick Support | Supported |
| High Speed Memory Stick Support | Supported |
| Memory Stick PRO Support | Supported |
| On-Chip Firmware | Firmware reads and writes High Speed Memory Stick and MS PRO |
| Integrated Card Power FETs | Integrated |
| USB Standard | USB 2.0 |
מדריך תצורת פינים של USB2228-NU-05 128-pin vtqfp (14 mm x 14 mm)
תצורת פינים עבור USB2228-NU-05 (מארזת 128-pin vtqfp (14 mm x 14 mm)). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור USB2228-NU-05.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
USB2228-NU-05 מתאים עבור 6 יישוםs: USB Flash Media Card Reader, Legacy Portable Media Adapter, Multifunction Peripherals, Embedded Flash-Media Gateway, Industrial Removable-Media Terminal, USB Media Docking Accessory.
USB Flash Media Card Reader
The USB2228-NU-05 fits a USB flash-media reader built for xD-Picture Card, SmartMedia, Memory Stick, High Speed Memory Stick, or Memory Stick PRO formats. Its USB 2.0 interface connects the reader to a host, while the parallel host-facing interface delegates supported flash-card transactions to dedicated controller circuitry. With a 3 V to 3.6 V operating range and a listed 75 mA supply current, it supports a regulated 3.3 V architecture. Designers should pair it with the appropriate media connectors, card-detection circuitry, and host firmware, while verifying insertion, removal, power sequencing, and supported-format behavior in the manufacturer reference design.
מומלץ
Legacy Portable Media Adapter
The USB2228-NU-05 is appropriate for a portable adapter that gives a modern USB host access to legacy removable flash media. Its fourth-generation controller supports xD-Picture Card, SmartMedia, Memory Stick, High Speed Memory Stick, and Memory Stick PRO, reducing the need to implement those protocols in a general-purpose embedded controller. The USB 2.0 upstream connection provides a standardized host interface, while the 3 V to 3.6 V supply range fits battery-derived 3.3 V rails after regulation. The principal design trade-off is media-format obsolescence: a new product should confirm that legacy cards remain a genuine market requirement before allocating board area around the 128-pin VTQFP.
מומלץ
Multifunction Peripherals
The USB2228-NU-05 can add legacy flash-media access to a multifunction peripheral that already communicates with a USB host. The controller's parallel interface and dedicated on-chip firmware for High Speed Memory Stick and MS PRO can offload media protocol handling from the system processor. Its USB 2.0 upstream connection allows the media function to coexist with other peripheral functions, while the listed 75 mA supply current helps establish the initial 3.3 V power budget. Integration still requires careful partitioning of USB, media, clock, and card-power signals, plus validation that the host software can expose the removable-media function safely during hot insertion and removal.
מומלץ
Embedded Flash-Media Gateway
The USB2228-NU-05 can serve as the removable-media gateway in an embedded system that bridges a USB host and supported legacy flash cards. Its dedicated controller architecture is useful when the main processor is occupied with application control and lacks practical media-protocol resources. Operating from 3 V to 3.6 V, the device fits a regulated 3.3 V power domain, and the 128-pin VTQFP exposes the necessary parallel and media connections. Because this is a specialized legacy-format controller, an engineer should evaluate the complete system cost, connector availability, media population, and long-term product support rather than adopting it merely because its upstream interface is USB 2.0.
מומלץ
Industrial Removable-Media Terminal
The USB2228-NU-05 may be used in an industrial or diagnostic terminal that accepts legacy flash media for configuration, logs, or field-service data. USB 2.0 provides a recognizable connection to host equipment, while support for xD-Picture Card, SmartMedia, Memory Stick, High Speed Memory Stick, and Memory Stick PRO permits use with the media formats already present in the installed base. The 3 V to 3.6 V operating range and 75 mA listed current support a conventional 3.3 V rail plan. Industrial adoption should account for connector robustness, ESD protection, card-power sequencing, enclosure access, and long-term availability. The controller should not be assumed suitable for newer SD or CF media without separate verification.
מומלץ
USB Media Docking Accessory
The USB2228-NU-05 is suitable for a docking accessory designed to recover data from supported removable flash formats. It connects to a computer or embedded host through USB 2.0 and uses its dedicated media-controller logic to handle xD-Picture Card, SmartMedia, Memory Stick, High Speed Memory Stick, and Memory Stick PRO. This architecture can produce a more consistent user experience than an entirely software-driven reader, especially where host operating-system support for legacy media is limited. The 3 V to 3.6 V supply range and 75 mA listed consumption simplify initial power budgeting, but the product must still address connector insertion life, card-power limits, media detection, firmware maintenance, and the 128-pin package's board-space requirement.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור USB2228-NU-05 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | USB2228-NU-05-E2 | USB2228-NU-05-E6 | USB2227-NU-05 | USB2251-NU-05 | USB2228-NU-05-E2C |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
מבדילים עיקריים
- Dedicated multi-format flash-media controller (לעומתUSB2251-NU-05)
- Integrated media-control firmware (לעומתUSB2227-NU-05)
- Documented USB 2.0 parallel-interface configuration (לעומתUSB2228-NU-05-E2)
- Integrated card-power FET functionality (לעומתUSB2251-NU-05)
הערות תכנון
Allocate the exact 128-lead VTQFP land pattern and preserve the manufacturer's recommended component and copper geometry. The verified package is 14 mm by 14 mm, so it is materially larger than common USB controller packages. Place decoupling and supporting components close to their associated pins, route high-speed USB signals as a controlled impedance pair, and avoid switching-regulator and magnetic-component placement beneath sensitive media or clock routes.
Design the USB2228 power rail for the verified 3 V to 3.6 V supply range and listed 75 mA supply current, adding margin for startup, card activity, and any attached media load. The integrated card-power FETs should be evaluated for the voltage, current, and sequencing requirements of every supported media format. Confirm absolute maximum ratings and output-load behavior in the manufacturer datasheet rather than extrapolating from the nominal 3.3 V operating condition.
Do not assume that USB 2.0 compliance means support for SD, CF, or generic USB flash storage. The verified USB2228 media list is xD-Picture Card, SmartMedia, Memory Stick, High Speed Memory Stick, and Memory Stick PRO. Confirm connector pinouts, insertion detection, card-power limits, host-driver behavior, and firmware support for the exact media population; otherwise the resulting product may satisfy the USB link while failing at the media interface.
Use the manufacturer reference design as the basis for clock, parallel-interface, media-connector, and card-power routing. Keep sensitive traces short where practical, provide continuous return paths beneath high-speed signals, and observe the package pin arrangement before finalizing connector orientation. The supplied excerpts do not expose individual pin names or routing values, so numerical trace geometry and component values should be copied from the applicable USB2227/USB2228 application guidance rather than estimated.
מידע על תאימות
The provided sources do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to the USB interface-controller function, but no automotive qualification claim is made. Obtain current declarations from Microchip Technology before procurement.
