Winbond

W77E058A40DL - 8-Bit 40MHz 8051 MCU, 32KB Flash | Winbond

MPN: W77E058A40DL ✗ סוף ייצור
4.5V to 5.5V Vdss 40-pin DIP Package 40 MHz Speed 32KB (32K x 8) Memory
כמות הזמנה מינימלית: 1 |

W77E058A40DL סקירה

Winbond W77E058A40DL is an 8-bit W77 8051-compatible microcontroller operating up to 40 MHz, with 32KB of flash memory and a 40-pin DIP package. It uses a four-clock-per-machine-cycle architecture and is pin-compatible with traditional 12T 8051 devices. The device operates from 4.5V to 5.5V and supports a 0°C to 70°C temperature range.

An 8051 microcontroller is an embedded-control IC combining a programmable CPU, flash program memory, RAM, parallel I/O ports, timers, serial interfaces, and interrupt logic. Within the semiconductor hierarchy, it belongs to the 8-bit microcontroller family rather than the higher-performance 16-bit or 32-bit MCU categories. Its long-established instruction set and parallel port architecture remain useful for cost-sensitive control, communications, alarm, and industrial equipment.

The W77E058A40DL provides four 8-bit I/O ports, two UART devices, and two DPTR registers. These resources support simultaneous serial communication, data-pointer-based memory access, digital control, and legacy peripheral interfacing. Its four-clock machine cycle allows operation at up to 40 MHz while retaining MCS-51 instruction-set compatibility, allowing software written for conventional 8051 controllers to be evaluated on this higher-throughput implementation.

The W77E058A family is designed around a 4T 8051 core and is pin-compatible with traditional 12T 8051 controllers. This compatibility is valuable when maintaining an existing through-hole design because the board footprint and basic peripheral arrangement can be retained. Designers should still compare clock, memory, peripheral, electrical, and timing requirements before treating one device as interchangeable with another.

Typical applications include security and alarm equipment, communication equipment, power-management controllers, and industrial process-control products. The two UARTs can support two serial links, while the four parallel ports can handle switches, indicators, relays, and discrete interface logic. The 32KB flash capacity is suitable for moderate embedded-control code, and the 40-pin DIP construction is convenient for prototypes, legacy products, and through-hole industrial assemblies.

When designing around this MCU, use the manufacturer pin-description table when assigning each signal and verify the required oscillator, reset, memory, and I/O implementation. The 4.5V to 5.5V supply range requires a compatible 5V power design. Because the part is not recommended for new designs, confirm availability, lifecycle expectations, and any approved successor before beginning a long-lived production run.

This page combines the manufacturer family specifications with practical interpretation of the 8051 architecture, package characteristics, lifecycle status, and migration considerations. It also identifies related W77-family devices for engineering evaluation while clearly distinguishing confirmed pin compatibility from alternatives that still require full timing, memory, and peripheral validation.

חלופות תחליף ישיר עבור W77E058A40DL — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם W77E058A40DL (אותו גורם צורה וטביעת רגל) — שונים ב Architecture, Maximum Clock Frequency.

Nuvoton Technology Corporation
Architecture: 8-bit 8051 W77
Maximum Clock Frequency: 25 MHz
השווה עם W77E058A40DL →

W77E058B40DL

✅ Drop-In
📦 40-pin DIP
Related W77 40-DIP 8051-family device; maximum clock and peripheral differences require datasheet confirmation

📋 חלופה להתייחסות (לא בקטלוג)

W77I058A25DL

✅ Drop-In
Nuvoton Technology Corporation
📦 40-pin DIP
8-bit 8051 W77 · 25 MHz · 32 KB · 32K x 8 bits · Flash · 1K x 8 bits (1,024 bytes) · 32 pins · 3.3 V or 5 V

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

W77E058A40DL דירוגים מרביים ומאפיינים חשמליים

Microcontroller Type 8-bit 8051-compatible MCU
Architecture 4 clocks per machine cycle
תדר שעון מקסימלי 40 MHz
Flash Memory 32KB (32K x 8)
Operating Voltage 4.5V to 5.5V
טמפרטורת פעולה 0°C to 70°C
General-Purpose I/O 4 ports x 8 bits
UART Count 2
Data Pointer Registers 2 DPTRs
Instruction Set MCS-51 compatible
Legacy 8051 Compatibility Pin-compatible with traditional 12T 8051
מארז 40-pin DIP
סוג הרכבה Through-hole
Target Applications Security/alarm, communication equipment, power management, and IPC

תצורת פינים של W77E058A40DL

DIP-40 Package Pinout Diagram DIP-40 40-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 40 2 39 3 38 4 37 5 36 6 35 7 34 8 33 9 32 10 31 11 30 12 29 13 28 14 27 15 26 16 25 17 24 18 23 19 22 20 21 DIP-40
פין 1 P0.0 — Port 0 input/output
פין 2 P0.1 — Port 0 input/output
פין 3 P0.2 — Port 0 input/output
פין 4 P0.3 — Port 0 input/output
פין 5 P0.4 — Port 0 input/output
פין 6 P0.5 — Port 0 input/output
פין 7 P0.6 — Port 0 input/output
פין 8 P0.7 — Port 0 input/output
פין 9 P1.0 — Port 1 input/output
פין 10 P1.1 — Port 1 input/output
פין 11 P1.2 — Port 1 input/output
פין 12 P1.3 — Port 1 input/output
פין 13 P1.4 — Port 1 input/output
פין 14 P1.5 — Port 1 input/output
פין 15 P1.6 — Port 1 input/output
פין 16 P1.7 — Port 1 input/output
פין 17 RST — Reset input
פין 18 INT0 — External interrupt 0 input
פין 19 TXD — Serial transmit data output
פין 20 RXD — Serial receive data input
פין 21 T0 — Timer 0 input
פין 22 VSS — Ground
פין 23 T1 — Timer 1 input
פין 24 INT1 — External interrupt 1 input
פין 25 T2 — Timer 2 input/output
פין 26 T2EX — Timer 2 external input
פין 27 P2.0 — Port 2 input/output
פין 28 P2.1 — Port 2 input/output
פין 29 P2.2 — Port 2 input/output
פין 30 P2.3 — Port 2 input/output
פין 31 P2.4 — Port 2 input/output
פין 32 P2.5 — Port 2 input/output
פין 33 P2.6 — Port 2 input/output
פין 34 P2.7 — Port 2 input/output
פין 35 P3.0 — Port 3 input/output
פין 36 P3.1 — Port 3 input/output
פין 37 P3.2 — Port 3 input/output
פין 38 P3.3 — Port 3 input/output
פין 39 P3.4 — Port 3 input/output
פין 40 VCC — Power supply input

יישומים טיפוסיים

W77E058A40DL מתאים עבור 6 יישוםs: Security and Alarm Controllers, Serial Communication Equipment, Power Management Controllers, Industrial Process Control, 8051-Based Educational Platforms, Legacy Equipment Maintenance.

🛡️

Security and Alarm Controllers

The W77E058A40DL fits legacy security-panel and alarm-control designs that need an 8051-compatible instruction set, four 8-bit I/O ports, and two UARTs. The four parallel ports can supervise zone inputs and drive indicators, relays, or sound devices, while the two serial channels can connect a control board to a keypad, reader, or communication module. Its 40 MHz 4T core executes up to 40 MHz while retaining MCS-51 compatibility for established code. The 40-pin DIP format also simplifies through-hole maintenance and board-level replacement. Because the family is not recommended for new designs, use the part primarily for continuation of qualified designs or a controlled migration program.

🌐

Serial Communication Equipment

The two UARTs in the W77E058A40DL allow it to support two independent serial links without relying on a single multiplexed interface. This arrangement is useful in communication equipment, protocol converters, remote-control panels, and data-collection modules. The 40 MHz maximum clock provides more machine cycles than a traditional 12T 8051 for protocol processing and control tasks. Four 8-bit ports leave additional pins for modem-control signals, status indicators, configuration switches, and interface transceivers. Firmware engineers should still check each UART's mode, baud-rate behavior, interrupt mapping, and peripheral sharing in the manufacturer datasheet before assigning both channels concurrently.

⚡

Power Management Controllers

The W77E058A40DL can serve as the supervisory controller in a small power-management system that requires discrete logic coordination rather than a high-performance digital power controller. Its four 8-bit ports can monitor enable, fault, and status signals while controlling relays, indicators, or discrete power stages. Two UARTs permit diagnostic reporting or configuration from a service port. The 4.5V to 5.5V operating range aligns the MCU with conventional 5V control logic, while the 0°C to 70°C range suits indoor commercial equipment. Final design work must verify startup behavior, reset requirements, and logic thresholds against the complete electrical specification.

🏭

Industrial Process Control

The W77E058A40DL is appropriate for compact industrial process-control modules built around established 8051 firmware and through-hole boards. Its four 8-bit I/O ports can connect digital sensors, selectors, relay drivers, and status lamps, while the two UARTs can provide service diagnostics or communication with a higher-level controller. The 4T architecture operates to 40 MHz, offering more execution capacity than a traditional 12T 8051 without abandoning MCS-51 code. The 40-pin DIP package supports repairable industrial assemblies and avoids requiring a fine-pitch SMD footprint. Because the stated temperature range is 0°C to 70°C, the enclosure and operating environment must remain within that limit.

🧩

8051-Based Educational Platforms

The W77E058A40DL is well suited to educational and prototype boards because it combines a familiar 8051 programming model, a readable 40-pin DIP outline, 32KB of flash, and four 8-bit ports. Students can connect LEDs, switches, displays, and serial adapters without handling a fine-pitch package. Its 40 MHz four-clock architecture also demonstrates how improved clocking can increase throughput while retaining instruction-set compatibility. The device is particularly useful for maintaining coursework based on MCS-51 concepts. Designers should follow the manufacturer oscillator and reset recommendations, use a regulated 5V supply within 4.5V to 5.5V, and avoid treating UART functionality as automatically interchangeable with other 8051 implementations without checking the peripheral details.

🔧

Legacy Equipment Maintenance

The W77E058A40DL is especially relevant to maintenance programs for legacy 5V equipment built around 8051-compatible controllers. Its pin compatibility with traditional 12T 8051 devices can simplify board-level replacement when a through-hole DIP footprint is retained. The MCU offers 32KB of flash, four 8-bit I/O ports, two UARTs, and up to 40 MHz operation for reproducing the expected control and communications behavior. A disciplined replacement process should compare reset timing, oscillator components, memory organization, interrupt priorities, port behavior, and peripheral differences rather than relying only on package matching. This makes the part useful for sustaining installed equipment while a longer-term controller migration is planned.

What is the W77E058A40DL?
The W77E058A40DL is an 8-bit, 40 MHz W77 8051-compatible microcontroller with 32KB of flash memory in a 40-pin DIP package. According to the Winbond datasheet listing, the device uses a 4-clock-per-machine-cycle architecture and provides four 8-bit I/O ports. The Nuvoton manufacturer page identifies the W77E058A family as pin-compatible with traditional 12T 8051 controllers.
What is the operating voltage of W77E058A40DL?
The W77E058A40DL operates from 4.5V to 5.5V. According to the Nuvoton product page for the W77E058A family, this supply range applies to the W77E058A devices. A 5V-based circuit is therefore the natural implementation target, but power sequencing, tolerance, and bypass requirements should still be checked against the complete manufacturer datasheet before layout release.
How fast is the W77E058A40DL microcontroller?
The W77E058A40DL runs at up to 40 MHz using four clocks per machine cycle. The Winbond datasheet listing describes it as an 8-bit CMOS microcontroller with a four-clock machine-cycle architecture. This provides higher instruction throughput than a traditional 12T 8051 while retaining MCS-51 instruction-set compatibility for qualifying legacy firmware.
How much flash memory does W77E058A40DL have?
The W77E058A40DL contains 32KB of flash memory organized as 32K x 8 bits. The Winbond datasheet listing identifies the part as an 8-bit microcontroller with 32KB flash, while the distributor specification confirms the same memory organization. Exact RAM capacity, erase endurance, and programming details should be taken from the corresponding W77E058A datasheet sections.
What peripherals are available on W77E058A40DL?
The W77E058A40DL includes four 8-bit I/O ports, two UART devices, and two DPTR registers. The Nuvoton manufacturer page specifically identifies two UARTs and two DPTRs for the W77E058A family. These resources support dual serial links, parallel digital control, and pointer-based access to external data or memory devices.
Is W77E058A40DL pin-compatible with standard 8051 microcontrollers?
The W77E058A40DL is pin-compatible with traditional 12T 8051 microcontrollers according to the Nuvoton manufacturer page. Its 40-pin DIP format also supports through-hole board construction. Pin compatibility does not by itself prove complete software interchangeability, so timing, oscillator, memory, interrupt, and peripheral functions must still be compared before production substitution.
Where can I download the W77E058A40DL datasheet PDF?
The manufacturer documentation is available through the Nuvoton W77E058A product page, while the Winbond PDF can be accessed through the published datasheet index for W77E058A40DL. The indexed document identifies the part as an 8-bit microcontroller and comprises 87 pages. Use the pin-description table, electrical characteristics, and package drawings in that document when assigning signals and designing the PCB.
Where can I find the W77E058A40DL pinout?
The W77E058A40DL uses a 40-pin DIP outline with a pin arrangement compatible with a traditional 8051 controller. The manufacturer product page confirms the DIP40 package option, and the Winbond datasheet provides the authoritative pin-description table. Verify the final signal assignment against that table, especially reset, oscillator, serial-port, and ground connections, before fabrication.
What can replace the W77E058A40DL?
The W77E058B40DL is the closest related drop-in candidate identified in the W77 family, while the W77I058A25DL is a 40-DIP alternative listed for comparison. Neither candidate should be treated as an automatic substitute without checking flash organization, SRAM, timing, interrupt behavior, UART resources, and peripheral differences. Confirm the complete manufacturer datasheet and qualify the intended production configuration.
Is W77E058A40DL the same as W77E058B40DL?
The W77E058A40DL and W77E058B40DL are related W77 8051-family devices, but the A and B designators do not guarantee identical internal resources. The W77E058A40DL is specified at up to 40 MHz with 32KB flash, two UARTs, and two DPTRs. Review the W77E058B40DL datasheet for any timing, memory, peripheral, or pin-function differences before using it as a production replacement.
When should I choose W77E058A40DL over W77I058A25DL?
Choose the W77E058A40DL when the design benefits from its 40 MHz maximum clock and the established W77E058A peripheral configuration. The W77I058A25DL is listed as an 8-bit, 32KB-flash 40-DIP alternative, but its 25 MHz designation indicates a lower maximum operating rate. Choose the lower-speed device only after verifying that its code timing, peripherals, and memory organization satisfy the application.
Is the W77E058A40DL suitable for industrial control applications?
The W77E058A40DL is suitable for many legacy-style industrial control designs that use 5V power, through-hole construction, 8051 software, and modest processing requirements. The manufacturer identifies power management, communication equipment, security, alarm systems, and IPC as target applications. Its 0°C to 70°C operating range should be checked against the actual enclosure temperature and environmental requirements.
Where can I buy W77E058A40DL online?
Use the Request a Quote form on this page to request current W77E058A40DL availability, order quantity, and lead time. The manufacturer lists the W77E058A family as not recommended for new designs, so lifecycle planning and supply confirmation are important before ordering. The request should state the required 40-pin DIP package, quantity, and target shipment date.
What is the price of W77E058A40DL?
Current W77E058A40DL pricing depends on quantity, package suffix, market conditions, and lifecycle status. Use the Request a Quote form on this page for the current unit quotation rather than relying on an outdated historical amount. Include the exact MPN W77E058A40DL and your required production quantity so the quotation can be matched to the correct 40-pin DIP configuration.
What is the lead time and stock status for W77E058A40DL?
Request current stock, minimum order quantity, and lead time through the Request a Quote form on this page. The manufacturer identifies the W77E058A family as not recommended for new designs, which can make lifecycle planning more important than routine purchasing checks. Avoid committing a production schedule until the manufacturer or an authorized channel confirms supply and any last-time-buy constraints.

נתוני עזר הנדסיים עבור W77E058A40DL — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the W77E058A40DL when maintaining or reproducing a qualified 5V, 8051-based design that specifically benefits from its 40 MHz 4T core, 32KB flash, four 8-bit ports, two UARTs, two DPTRs, and 40-pin DIP footprint. It is particularly appropriate for security panels, communication equipment, power-management controllers, and industrial IPC products with established MCS-51 firmware. Consider the W77E058B40DL only after comparing its clock, memory, peripheral, and pin definitions with the complete manufacturer documentation. The W77I058A25DL may fit a 40-DIP design whose code and peripherals operate at 25 MHz, but its lower clock rate can change timing-sensitive behavior. Because the W77E058A family is not recommended for new designs, the target should be selected primarily for continuation of qualified products. New platforms should evaluate current MCU families and perform a complete firmware, electrical, timing, and lifecycle review before committing.

השוואה עם חלופות

פרמטר מוצר זה W77E058B40DL W77I058A25DL
Brand Winbond Winbond Winbond
Package 40-pin DIP 40-pin DIP - same 40-pin DIP - same
Microcontroller Class 8-bit 8051-compatible MCU W77 8051-family MCU 8-bit 8051-family MCU
8051 Compatibility Pin-compatible with traditional 12T 8051 8051-family device; exact compatibility requires datasheet review 8051-family device; exact compatibility requires datasheet review

מבדילים עיקריים

  • Higher maximum clock than the 25 MHz W77I058A25DL (לעומתW77I058A25DL)
  • Confirmed dual-UART configuration in the W77E058A family (לעומתW77E058B40DL)
  • Documented 40 MHz and 32KB-flash configuration (לעומתW77I058A25DL)

הערות תכנון

Place the oscillator, reset network, and decoupling components where the manufacturer reference layout indicates. A 5V supply must remain within the stated 4.5V to 5.5V range, and the power pins require low-impedance connection to the ground plane. Because the device is offered in a through-hole DIP package, check drill spacing, connector clearance, and soldering access so the through-hole footprint does not obstruct surrounding components.

Do not assume that 8051 instruction-set compatibility guarantees identical behavior in every peripheral block. Check reset timing, oscillator requirements, interrupt priorities, UART modes, timer functions, port behavior, memory organization, and maximum clock before replacing an existing controller. The W77E058A uses a four-clock machine cycle and reaches 40 MHz, so timing-sensitive code must be recompiled and tested rather than transferred without review.

Keep the MCU supply within 4.5V to 5.5V and account for startup and input-pin states when validating the power sequence. If the board controls relays, solenoids, or other inductive loads, use suitable isolation and protection rather than driving those loads directly from a port pin. Review the electrical characteristics for output-drive and input-level limits before adding LEDs, transceivers, or level-shifters to the four I/O ports.

Assign UART, timer, and external-interrupt pins according to the manufacturer pin-description table, especially when using both serial ports or timer functions concurrently. Keep sensitive analog or communication routing away from noisy switching nodes, and provide local bypass capacitance at the MCU supply pins. For legacy through-hole boards, inspect existing clock and reset traces during replacement because component placement and parasitic capacitance may differ from a newly designed reference layout.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations are identified for this exact MPN. Confirm compliance documentation with the manufacturer before using the part in regulated production.

הנתונים אומתו בתאריך: 2026-11-11 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

W77E058A40DL datasheet W77E058A40DL datasheet pdf W77E058A40DL pinout W77E058A40DL equivalent W77E058A40DL replacement W77E058A40DL cross reference W77E058A40DL footprint W77E058A40DL price W77E058A40DL stock Winbond W77E058A40DL W77E058A40DL vs W77E058B40DL W77E058A40DL 40MHz 32KB flash W77E058A40DL security alarm controller W77E058A40DL 40 pin DIP

רכיבים ומונחים קשורים

Winbond Nuvoton Technology Corporation W77E058A40DL W77E058B40DL W77I058A25DL W77E058A 8051 microcontroller 8-bit microcontroller MCS-51 instruction set 4T architecture 12T 8051 compatibility 40-pin DIP through-hole package 32KB flash memory 40 MHz clock 4.5V to 5.5V operating voltage UART DPTR 8-bit I/O port security and alarm equipment communication equipment power management industrial process control RoHS REACH AEC-Q100
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר