CP2101R vs CP2102N-A01-GQFN28R तुलना
विस्तृत दोनों ओर की तुलना CP2101R द्वारा Silicon Labs और CP2102N-A01-GQFN28R द्वारा Silicon Labs. मुख्य विशेषताओं, इलेक्ट्रिकल पैरामीटर, पैकेजिंग, चक्र स्थिति, मूल्यांकन और उपलब्धता को तुलना करके अपनी डिजाइन की आवश्यकताओं के लिए सबसे अच्छा घटक निर्धारित करें。
Silicon Labs
CP2102N-A01-GQFN28R - USB to UART Bridge QFN-28 | Silicon Labs
CP2102N-A01-GQFN28R ✓ सक्रियविशेषता तुलना
| पैरामीटर | CP2101R | CP2102N-A01-GQFN28R |
|---|---|---|
| ब्रांड | Silicon Labs | Silicon Labs |
| श्रेणी | Interface ICs | Interface ICs |
| लाइफसाइकिल स्थिति | सक्रिय | सक्रिय |
| Product Type | USB-to-UART bridge controller | USB to UART Bridge Controller |
| USB Interface | USB 2.0 | — |
| सप्लाई वोल्टेज | 3 V to 3.6 V | — |
| Serial Interface | UART | — |
| Protocol | USB | — |
| पैकेज | 28-MLP (5 x 5 mm) | 28-QFN (5x5 mm) with exposed pad |
| Case / Package | 28-VFQFN exposed pad | — |
| Packaging | Cut Tape (CT) | — |
| Interface Function | USB 2.0 UART interface | — |
| Device Category | I/O controller interface IC | — |
| USB Speed | [DATA_NEEDED: USB operating speed] | — |
| Maximum UART Data Rate | [DATA_NEEDED: maximum UART baud rate] | — |
| ऑपरेटिंग तापमान | [DATA_NEEDED: operating temperature range] | -40 C to +85 C |
| UART Signal Levels | [DATA_NEEDED: UART signal-level specification] | — |
| ESD Protection | [DATA_NEEDED: ESD protection rating] | — |
| RoHS स्थिति | unknown | Compliant |
| REACH Status | unknown | — |
| AEC-Q100 Qualification | not_applicable | — |
| थर्मल रेज़िस्टेंस | [DATA_NEEDED: exposed-pad thermal resistance] | — |
| Series | — | USBXpress |
| USB Standard | — | USB 2.0 Full-Speed (12 Mbps) |
| UART Interface | — | USB 2.0 UART |
| Number of UART Channels | — | 1 |
| डेटा दर | — | 300 baud to 1 Mbaud |
| Supply Voltage (VBUS) | — | 4.0 V to 5.25 V |
| Supply Voltage (VDD) | — | 3.0 V to 3.6 V |
| Internal Regulator Output | — | 3.3 V (up to ~100 mA) |
| माउंटिंग प्रकार | — | Surface Mount |
| GPIO | — | Yes (multiple, signal-configurable) |
| Reset Pin | — | RSTb (active-low hardware reset) |
| On-chip Oscillator | — | Yes (no external crystal required) |
| MSL स्तर | — | MSL3 (per JEDEC J-STD-020) |
| Host Driver | — | Silicon Labs CP210x VCP driver |