EPC2TC32UCAF48 vs EPC2TC32UCF48 तुलना
विस्तृत दोनों ओर की तुलना EPC2TC32UCAF48 द्वारा Altera और EPC2TC32UCF48 द्वारा Intel. मुख्य विशेषताओं, इलेक्ट्रिकल पैरामीटर, पैकेजिंग, चक्र स्थिति, मूल्यांकन और उपलब्धता को तुलना करके अपनी डिजाइन की आवश्यकताओं के लिए सबसे अच्छा घटक निर्धारित करें。
विशेषता तुलना
| पैरामीटर | EPC2TC32UCAF48 | EPC2TC32UCF48 |
|---|---|---|
| ब्रांड | Altera | Intel |
| श्रेणी | FPGA & CPLD | Memory ICs |
| लाइफसाइकिल स्थिति | Obsolete | NRND |
| मेमोरी आकार | 1.6 Mb | — |
| Device Family | EPC2 (Enhanced Configuration Device) | — |
| Programmability | In-system programmable (ISP) via JTAG | — |
| इंटरफ़ेस | 4-wire serial (nCS, DCLK, DATA, nINIT_CONF) + JTAG | — |
| Supply Voltage (VCC) | 3.3 V nominal | 3.0 V to 3.6 V (3.3 V typical) |
| FPGA Compatibility | Altera SRAM-based LUT FPGAs (Cyclone, Stratix, APEX, ACEX, FLEX, MAX 9000) | — |
| Cascading | Supported for bitstreams larger than 1.6 Mb | — |
| पैकेज | 32-pin TQFP (CAF48 designation per Altera ordering code) | 48-pin TQFP (7x7 mm) |
| ऑपरेटिंग तापमान | [DATA_NEEDED: commercial 0-70C vs industrial -40-85C variant] | 0C to +70C (commercial) |
| Data Retention | 10 years typical (EEPROM-based) | — |
| Programming Cycles | 100 cycles minimum (EEPROM endurance) | — |
| Process Technology | CMOS EEPROM | — |
| माउंटिंग प्रकार | Surface Mount | Surface Mount |
| MSL स्तर | [DATA_NEEDED: MSL classification] | [DATA_NEEDED: MSL rating] |
| RoHS स्थिति | [DATA_NEEDED: per ordering code; older CAF48 lots were non-RoHS] | [DATA_NEEDED: confirm RoHS compliance] |
| मेमोरी प्रकार | — | Non-volatile configuration PROM (CMOS Flash-based) |
| Memory Density | — | 1.6 Mbit (1.6 Mb / 32 Mbit raw) |
| Memory Configuration | — | Serial configuration bitstream storage |
| Supply Voltage (VCCIO) | — | 1.8 V / 2.5 V / 3.3 V (bank-level) |
| Output Drive Current (VCCIO) | — | [DATA_NEEDED: IOH/IOL at 3.3 V VCCIO] |
| Programming Interface | — | IEEE Std. 1149.1 JTAG (in-system programmable) |
| Configuration Interface | — | Altera serial PROM interface (DCLK, DATA, nCONFIG, nSTATUS, CONF_DONE) |
| Supported Configuration Modes | — | FPP, AS, PS, JTAG (mode dependent on target FPGA MSEL pins) |
| Daisy Chain Support | — | Yes (multi-device cascade for >16 Mbit FPGAs) |
| Maximum Cascaded Capacity | — | Up to 16 Mbit total across chain |
| Lead Free | — | [DATA_NEEDED: confirm lead-free] |