AD8005ANZ - 170MHz Current Feedback Op Amp | Analog Devices
MPN: AD8005ANZ ✓ सक्रियAD8005ANZ अवलोकन
A current-feedback amplifier is a voltage-feedback operational-amplifier alternative optimized for high-speed closed-loop systems. Instead of relying primarily on open-loop gain for bandwidth, its feedback impedance determines much of the operating behavior. This architecture supports wide bandwidth at moderate gain and is frequently used when signals must be amplified, buffered, or conditioned without the bandwidth reduction associated with conventional voltage-feedback amplifiers.
The AD8005 combines a 170 MHz bandwidth with a 280 V/µs slew rate, allowing it to preserve large-amplitude, rapidly changing signals. Its gain flatness is 0.1 dB to 30 MHz, while differential gain and phase errors are 0.11% and 0.4°. The 400 µA quiescent current reduces power demand in battery-powered and portable systems without narrowing the amplifier's high-frequency operating range.
Low distortion is another important characteristic for precision signal paths. The manufacturer reports THD of −63 dBc at 1 MHz and −50 dBc at 10 MHz. These figures make the amplifier relevant to video, communications, medical instrumentation, and data-acquisition systems where input signals must remain faithful through amplification and buffering. Current-feedback behavior also makes feedback-resistor selection an important part of achieving the intended bandwidth and gain.
Typical uses include high-speed ADC signal conditioning, video-buffer stages, portable diagnostic equipment, communication receivers, and low-power test systems. The amplifier can serve as a general-purpose high-speed buffer when its power-supply requirements, stability conditions, and feedback network are compatible with the intended signal. Its low 400 µA quiescent current is particularly useful when battery life is more important than continuous full-scale output drive.
Designers should follow the manufacturer datasheet for the complete power-supply range, input common-mode limits, output swing, recommended feedback resistors, and stability configuration. The AD8005ANZ is a current-feedback device, so its gain-bandwidth behavior differs from a conventional voltage-feedback amplifier. Decoupling, grounding, and short feedback paths remain essential for preserving the advertised bandwidth and distortion performance.
This product page combines the manufacturer's key performance figures, a practical application guide, package and pin information, and a parameter-by-parameter comparison with same-footprint current-feedback amplifiers. It is intended to help engineers evaluate whether the AD8005ANZ's combination of 170 MHz bandwidth, 280 V/µs slew rate, low distortion, and 400 µA quiescent current fits a particular high-speed, low-power design.
के लिए ड्रॉप-इन विकल्प AD8005ANZ — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
AD8042AN
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD8045AN
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD8055AN
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD8065AN
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD8066AN
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
AD8005ANZ Maximum Ratings और Electrical Characteristics
| Amplifier Type | Current-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Signal Bandwidth | 170 MHz |
| Quoted Mouser Bandwidth | 270 MHz |
| Slew Rate | 280 V/µs |
| Quiescent Supply Current | 400 µA |
| Gain Flatness | 0.1 dB to 30 MHz |
| Differential Gain Error | 0.11% |
| Differential Phase Error | 0.4° |
| Total Harmonic Distortion at 1 MHz | −63 dBc |
| Total Harmonic Distortion at 10 MHz | −50 dBc |
| पैकेज | 8-pin PDIP |
| माउंटिंग प्रकार | Through-hole |
AD8005ANZ पिन कॉन्फ़िगरेशन
| पिन 1 | −IN — Inverting input |
| पिन 2 | +IN — Non-inverting input |
| पिन 3 | −VS — Negative supply pin; connect to ground for single-supply operation |
| पिन 4 | NC — Not connected |
| पिन 5 | NC — Not connected |
| पिन 6 | +VS — Positive supply pin |
| पिन 7 | −OUT — Inverting output |
| पिन 8 | +OUT — Non-inverting output |
सामान्य अनुप्रयोग
AD8005ANZ के लिए उपयुक्त है 6 अनुप्रयोगs: High-Speed ADC Signal Conditioning, Portable Video Signal Buffering, Medical Instrumentation Signal Paths, Communication Receiver Front Ends, Portable Test and Measurement Equipment, Industrial Sensor Signal Conditioning.
High-Speed ADC Signal Conditioning
The AD8005ANZ fits ADC front ends that require amplification or buffering before conversion. Its 170 MHz signal bandwidth and 280 V/µs slew rate preserve fast-moving analog inputs, while the 400 µA quiescent current limits the amplifier's static power demand. The amplifier can also provide current-feedback gain with a short feedback path to reduce parasitic inductance. The Analog Devices datasheet identifies high-speed A-to-D converter signal conditioning as a target application. The exact implementation must account for ADC input bandwidth, converter input capacitance, common-mode range, and the feedback-resistor value recommended for the intended closed-loop gain.
अनुशंसित
Portable Video Signal Buffering
The AD8005ANZ is appropriate for compact video paths where signal bandwidth matters more than continuous output-current capability. Its 170 MHz bandwidth provides margin for high-resolution video components, while the 280 V/µs slew rate supports rapid edge transitions. Quiescent current of 400 µA helps reduce consumption in portable equipment. Analog Devices specifically identifies portable video systems as an application for the AD8005. In implementation, the source impedance, video amplitude, termination network, output loading, and selected feedback resistor determine whether gain and distortion meet the target system requirements.
अनुशंसित
Medical Instrumentation Signal Paths
The AD8005ANZ can serve as a high-frequency signal-conditioning amplifier in portable medical instruments where sensor signals must be amplified without excessive power consumption. The 170 MHz bandwidth and 280 V/µs slew rate support rapid biological or diagnostic waveforms, while differential gain error of 0.11% and differential phase error of 0.4° help preserve signal integrity. The 400 µA quiescent current is attractive for battery-operated equipment. Medical designs must still evaluate the complete amplifier supply range, input and output limits, noise performance, patient-safety isolation, and application-specific qualification requirements.
अनुशंसित
Communication Receiver Front Ends
The AD8005ANZ is suitable for communication receiver chains that require low-power amplification of rapidly changing signals. Its 170 MHz bandwidth covers a broad range of intermediate-frequency and baseband signal-conditioning needs, while the 280 V/µs slew rate supports large output transitions. The low 400 µA quiescent current benefits portable radio and battery-powered instrumentation. System designers should compare the amplifier's noise, gain stability, output swing, and distortion against the receiver's modulation format and front-end gain plan, then verify the chosen feedback network using the manufacturer's stability and application guidance.
अनुशंसित
Portable Test and Measurement Equipment
The AD8005ANZ can support probe buffers, signal conditioners, and data-acquisition front ends in portable test equipment. Its 170 MHz bandwidth accommodates high-frequency test signals, and its 280 V/µs slew rate preserves large slew conditions without requiring the higher quiescent current of many conventional high-speed amplifiers. A 400 µA quiescent current improves battery life during intermittent measurements. The design must account for probe capacitance, source impedance, permissible loading, connector bandwidth, and the feedback resistor required to maintain stability across the operating gain range.
अनुशंसित
Industrial Sensor Signal Conditioning
The AD8005ANZ can condition fast sensor outputs in industrial measurement systems where low signal amplitude must be amplified into a downstream converter or instrumentation chain. Its 170 MHz bandwidth provides more than enough bandwidth for many sensor signals, while the 280 V/µs slew rate handles transient events and the 400 µA quiescent current supports low-power acquisition modules. Analog Devices identifies signal conditioning and buffering as key uses. Engineers should verify input bias behavior, common-mode limits, output swing, noise, EMI susceptibility, and grounding when the sensor is physically separated from the amplifier.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा AD8005ANZ — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | AD8042AN | AD8045AN | AD8055AN | AD8065AN | AD8066AN |
|---|---|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pintechnology PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Architecture | Current feedback | Current feedback | Current feedback | Current feedback | Current feedback | Current feedback |
| Signal Bandwidth | 170 MHz | 210 MHz | 345 MHz | 250 MHz | 145 MHz | 145 MHz |
| Slew Rate | 280 V/µs | 140 V/µs | 200 V/µs | 200 V/µs | 180 V/µs | 125 V/µs |
| Quiescent Supply Current | 400 µA | 10 mA | 6.6 mA | 3 mA | 12 mA | 12 mA |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
मुख्य विशेषताएँ
- Exceptionally low quiescent current for a 170 MHz current-feedback amplifier (बनामAD8065AN)
- Higher slew rate than the AD8042AN while retaining the same PDIP footprint (बनामAD8042AN)
- Lower power consumption than the AD8055AN in the same package (बनामAD8055AN)
- Documented gain accuracy and distortion for high-speed signal paths (बनामAD8045AN)
डिज़ाइन नोट्स
Do not treat the AD8005ANZ like a conventional voltage-feedback amplifier when setting closed-loop gain. In a current-feedback amplifier, the feedback resistor is a primary determinant of gain and stability. Select the resistor using the Analog Devices gain-versus-feedback-resistance guidance, keep the feedback trace short, and avoid adding capacitance across it unless the manufacturer explicitly supports that configuration.
Keep the input, output, feedback, and supply-return paths compact to preserve the advertised 170 MHz bandwidth and 280 V/µs slew rate. Place supply-bypass capacitors close to the relevant power pins and use a low-impedance ground connection. At these frequencies, long PCB traces and inductance in the feedback loop can add ringing, reduce phase margin, or degrade the 0.1 dB gain-flatness performance through 30 MHz.
Estimated: quiescent dissipation is 400 µA multiplied by the selected supply voltage. At a 5 V supply, that is 2 mW before output-current and external-load effects are included. Confirm the actual supply range and output-current capability in the manufacturer datasheet, provide local bypassing, and include amplifier output drive in the final thermal budget rather than relying on quiescent current alone.
Validate source impedance, capacitive loading, and gain with the final circuit because current-feedback amplifiers can change stability behavior as output loading changes. Use short connections around the device, controlled termination, and the manufacturer's test setup when comparing results. The specified distortion figures of −63 dBc at 1 MHz and −50 dBc at 10 MHz should be assessed at the intended output amplitude and frequency rather than assumed across every operating condition.
अनुपालन जानकारी
The AD8005ANZ is a general-purpose operational amplifier, so AEC-Q100 qualification is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the retrieved product information.