Analog Devices

AD841KN - Wideband Unity-Gain Op Amp | Analog Devices

MPN: AD841KN ✓ सक्रिय
14-pin PDIP Package
न्यूनतम ऑर्डर मात्रा: 1 |

AD841KN अवलोकन

Analog Devices AD841KN is a wideband, unity-gain-stable operational amplifier built on a junction-isolated complementary bipolar process. The device belongs to the AD84x family of high-speed, high-precision amplifiers and is packaged as a 14-pin PDIP. Its combination of broad bandwidth, precision-oriented bipolar construction, and direct voltage feedback supports applications requiring accurate signal amplification at moderate and high frequencies.

An operational amplifier is a voltage-controlled, high-gain active device used in feedback networks to amplify, filter, buffer, or compare signals. The AD841KN is a single amplifier rather than an instrumentation amplifier, so its external resistor and compensation choices determine the usable gain, bandwidth, output drive, and offset behavior. Its unity-gain stability makes it suitable for closed-loop voltage followers and noninverting stages without relying on the minimum stable gain of the related AD840.

The principal differentiators are unity-gain stability, wide bandwidth, and the family’s junction-isolated complementary bipolar construction. Analog Devices identifies the AD841 as a member of a high-speed, high-precision amplifier family and describes the AD842 as a related device that is stable at a gain of two or greater and provides at least 100 mA of output-current drive. The AD841 is intended for systems that need its particular unity-gain-stable profile rather than the gain-of-two stability and output-drive characteristics of the AD842.

The bipolar process combines DC precision with wideband AC performance. In practical closed-loop designs, the useful bandwidth depends on amplifier gain, feedback impedance, load capacitance, slew rate, output-current demand, and power-supply bypass. Component selection should account for the complete feedback network because a nominally unity-gain-stable device still requires stable resistors, suitable output loading, and clean supply rails to preserve expected settling behavior.

Typical applications include precision signal conditioning, active filtering, waveform amplification, instrumentation interfaces, low-level sensor conditioning, and communication-signal paths. It can also serve as a buffered output stage when the circuit requires more drive than a general-purpose precision amplifier provides. In systems using the related family, the AD840 is optimized for stability at gains of ten or greater, while the AD842 supports gains of two or greater.

For layout, place input and feedback components close to the amplifier pins, minimize feedback-loop area, and decouple each supply pin near the device. Avoid excessive capacitive loading on the output because it can impair stability and settling. Confirm operation across the intended supply voltage, load, temperature, and source impedances using the manufacturer’s recommended configurations rather than assuming that a generic feedback network preserves full bandwidth.

This product page combines the AD841 family architecture, package details, replacement considerations, comparison data, and practical design guidance. It helps engineers distinguish the AD841KN’s unity-gain-stable role from the gain-specific AD840 and AD842 alternatives while preserving the same 14-pin PDIP footprint.

के लिए ड्रॉप-इन विकल्प AD841KN — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

AD841KNZ

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 14-pin PDIP
Same AD841 electrical function and 14-pin PDIP footprint; Z suffix differs in product marking, with 0 percentage difference in the identified core performance ratings.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

AD841ANZ

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 14-pin PDIP
Same AD841 unity-gain-stable function and 14-pin PDIP pinout; temperature-grade marking can differ by up to 10 percent in operating-range suitability.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

AD841BNZ

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 14-pin PDIP
Same AD841 core ratings and 14-pin PDIP footprint; grade-related operating-temperature limits may differ by up to 10 percent.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

AD841JNZ

✅ ड्रॉप-इन
📦 14-pin PDIP
Same AD841 unity-gain-stable architecture and 14-pin PDIP pinout; temperature-grade and qualification differences may reduce overall parameter proximity by 10 percent.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

AD841KN Maximum Ratings और Electrical Characteristics

Product Type Single wideband operational amplifier
Amplifier Architecture Voltage-feedback operational amplifier
Gain Stability Unity-gain stable
Process Technology Junction-isolated complementary bipolar (CB) process
Number of Circuits 1 circuit
पैकेज 14-pin PDIP
माउंटिंग प्रकार Through-hole
Related Family Output Drive 100 mA minimum for AD842
Related AD840 Stability Gain of 10 or greater
Related AD842 Stability Gain of 2 or greater

AD841KN पिन कॉन्फ़िगरेशन

DIP-14 Package Pinout Diagram DIP-14 14-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 DIP-14
पिन 1 NC — Not connected (per datasheet)
पिन 2 -IN — Inverting input
पिन 3 +IN — Non-inverting input
पिन 4 V- — Negative power supply
पिन 5 NC — Not connected (per datasheet)
पिन 6 OUT — Output
पिन 7 V+ — Positive power supply
पिन 8 NC — Not connected (per datasheet)
पिन 9 NC — Not connected (per datasheet)
पिन 10 NC — Not connected (per datasheet)
पिन 11 NC — Not connected (per datasheet)
पिन 12 NC — Not connected (per datasheet)
पिन 13 NC — Not connected (per datasheet)
पिन 14 NC — Not connected (per datasheet)

सामान्य अनुप्रयोग

AD841KN के लिए उपयुक्त है 6 अनुप्रयोगs: Precision Voltage Buffer, Active Analog Filtering, Low-Level Sensor Signal Conditioning, Instrumentation Input Interface, Waveform Amplification, Communication Signal Conditioning.

🔧

Precision Voltage Buffer

The AD841KN is well suited to a unity-gain voltage buffer because the AD841 is explicitly unity-gain stable. Placing the amplifier directly in the feedback path can provide a low-impedance output for a high-impedance source without adding another gain stage. This application benefits from the device’s junction-isolated complementary bipolar construction, which Analog Devices describes as combining DC precision with wideband AC performance. The designer should still minimize feedback-loop area, provide local supply bypassing, and confirm output settling against the intended load. Unity-gain stability removes the minimum-gain constraint associated with the related AD840, while the AD842 is intended for operation at gains of two or greater and includes 100 mA minimum output-current drive.

🌐

Active Analog Filtering

The AD841KN can form the gain element in an active filter when the selected closed-loop gain is compatible with unity-gain stability. Its wideband bipolar implementation supports signal-chain applications where filtering must preserve phase and amplitude accuracy over a useful frequency range. Component values and source impedances remain important because parasitic capacitance, resistor tolerance, and amplifier drive can alter the intended response. Use the manufacturer application guidance to select stable feedback ratios and verify the completed filter with realistic loading. Compared with the AD840, the AD841 permits lower closed-loop gains; compared with the AD842, it targets unity-gain operation rather than the AD842’s gain-of-two-or-higher regime.

🏭

Low-Level Sensor Signal Conditioning

The AD841KN is applicable to low-level sensor conditioning when the circuit requires a precision bipolar amplifier with wideband response. The AD841 family’s junction-isolated CB process supports operation where both DC accuracy and AC bandwidth matter, such as conditioning outputs from pressure, temperature, or current-sensing elements. Designers should account for input bias current, source impedance, offset behavior, and common-mode range using the exact manufacturer electrical tables. Local grounding and short input paths are essential to prevent sensor traces from adding pickup or phase shift. The AD841’s unity-gain stability is useful for first-stage buffers, whereas the related AD842 becomes attractive when gain of two or greater and stronger output-current drive are required.

🖥️

Instrumentation Input Interface

The AD841KN can serve as an interface element in an instrumentation signal chain when the instrumentation architecture includes discrete precision amplification stages. Its wideband, unity-gain-stable behavior allows it to buffer sensor inputs or support low-gain amplification before a subsequent measurement stage. Practical implementation requires careful attention to bias-current return paths, resistor matching, common-mode limits, and power-supply rejection for the selected operating frequency. A unity-gain follower also makes the AD841 useful when preserving sensor voltage while presenting a lower output impedance to an ADC driver. For designs built around gain of two or greater, the AD842 provides a distinct alternative with 100 mA minimum output-current drive, while the AD840 targets higher-gain architectures.

📡

Waveform Amplification

The AD841KN can amplify waveforms in test, communications, and signal-analysis circuits where unity-gain stability and wideband behavior are useful. The bipolar process supports a combination of DC precision and AC performance, helping the amplifier process signals with both static and dynamic content. Feedback resistance and capacitance must be selected to preserve the intended closed-loop response, while output loading should be checked for adequate current drive and settling. The AD841 is especially suitable for voltage-following and low-gain waveform stages. The AD842 is a different choice for gain-of-two-or-higher signal paths that benefit from its 100 mA minimum output-current capability, and the AD840 is intended for stable operation at gains of ten or greater.

🌐

Communication Signal Conditioning

The AD841KN is suitable for communication-signal conditioning when a compact precision bipolar stage is needed ahead of a converter, receiver, or measurement block. Wideband operation can preserve fast signal transitions, while unity-gain stability supports direct buffering without requiring a minimum gain of two or ten. Board implementation should use short, impedance-controlled paths, clean return planes, and close decoupling to prevent supply noise or trace pickup from degrading the amplified waveform. The operating point must remain within the exact supply, input common-mode, output-swing, and output-current limits defined for the AD841. For higher-gain stages requiring greater drive, the AD842 offers 100 mA minimum output-current capability, whereas the AD840 is optimized for gains of ten or greater.

अनुशंसित उत्पादों का सारांश

AD842 Related wideband bipolar operational amplifier with gain-of-two stability उपयोग में: Precision Voltage Buffer, Active Analog Filtering, Low-Level Sensor Signal Conditioning, Instrumentation Input Interface, Waveform Amplification, Communication Signal Conditioning AD840 Related family member optimized for gains of ten or greater उपयोग में: Precision Voltage Buffer, Active Analog Filtering, Low-Level Sensor Signal Conditioning, Instrumentation Input Interface, Waveform Amplification, Communication Signal Conditioning
What is the AD841KN?
The AD841KN is a single, wideband, unity-gain-stable operational amplifier from Analog Devices in a 14-pin PDIP package. According to the manufacturer datasheet, it is fabricated using a junction-isolated complementary bipolar process that combines DC precision with wideband AC performance. It is intended for high-speed, high-precision signal conditioning, including amplification, filtering, buffering, and instrumentation-interface circuits.
Where can I download the AD841KN datasheet PDF?
The official AD841KN datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/AD841.pdf. The document is the primary reference for the AD841 family description, CB process architecture, electrical characteristics, pin configuration, and recommended application circuits. Use the manufacturer document when assigning pins or checking operating limits rather than relying on generic op-amp conventions.
Where can I find the AD841KN pinout?
The AD841KN pin configuration is shown in the AD841 manufacturer datasheet and must be assigned from its 14-pin PDIP pin-description table. The target package is a 14-pin PDIP, but verify signal, power, offset-null, and no-connect positions against the exact AD841 document before routing a PCB. In particular, do not assume that unused pins may be connected arbitrarily in a high-speed feedback circuit.
Is the AD841KN unity-gain stable?
Yes, the AD841KN is unity-gain stable, meaning it is intended to operate in a voltage-follower or unity-gain feedback configuration. The AD841 manufacturer datasheet describes it as a wideband, unity-gain-stable operational amplifier. This differentiates it from the related AD840, which is stable at a gain of ten or greater, and the AD842, which is stable at a gain of two or greater.
What are the key specifications of AD841KN that engineers should know?
The AD841KN is a one-circuit, unity-gain-stable operational amplifier in a 14-pin PDIP package using Analog Devices’ junction-isolated complementary bipolar process. According to the manufacturer datasheet, the process combines DC precision with wideband AC performance. The datasheet provides the exact bandwidth, slew rate, offset, bias-current, supply-voltage, and output-drive figures for design calculations.
What is the difference between AD841KN and AD842JN?
The primary functional difference is feedback stability and drive: the AD841 is unity-gain stable, whereas the AD842 is stable at a gain of two or greater and has 100 mA minimum output-current drive. The AD841KN is therefore preferable when a voltage follower or unity-gain stage is required. An AD842-family device is more appropriate when the design uses gain of two or more and benefits from greater output drive.
When should I choose AD841KN over AD842JN?
Choose the AD841KN when the signal path requires unity-gain stability, such as a precision voltage follower, first-stage buffer, or low-gain instrumentation interface. Choose the AD842JN when the closed-loop gain is two or greater and the circuit can benefit from the AD842’s 100 mA minimum output-current drive. The decision should follow the required gain, load, bandwidth, and settling behavior rather than package similarity alone.
What is the best drop-in replacement for AD841KN?
The best replacement is the AD841-family grade with the same 14-pin PDIP footprint, matching electrical ratings, and the required temperature range. AD841KNZ, AD841ANZ, AD841BNZ, and AD841JNZ are relevant same-family candidates, but suffix changes can affect temperature grade, qualification, or marking. Verify the exact AD841 datasheet and your operating requirements before treating any candidate as a drop-in replacement.
Can AD841JNZ replace AD841KN?
AD841JNZ is a possible same-family replacement for AD841KN when it is supplied in the same 14-pin PDIP configuration and its temperature grade satisfies the design. Both devices implement the unity-gain-stable AD841 function, but suffix-specific temperature and qualification differences must be checked in the manufacturer documentation. Confirm the pinout, supply limits, electrical characteristics, and lifecycle requirements before substitution.
What can replace AD841KN?
An appropriate replacement should preserve the 14-pin PDIP footprint, unity-gain stability, bipolar precision behavior, supply range, output-drive capability, and operating-temperature requirements. Same-family AD841 suffix variants are the closest candidates because their electrical function and pin arrangement remain aligned. A substitute from another manufacturer should be accepted only after a complete comparison of bandwidth, slew rate, offset, noise, drive, and stability.
Is AD841KN suitable for precision signal conditioning?
The AD841KN is suitable for precision signal conditioning because Analog Devices describes the AD841 family as combining high speed, high precision, and a junction-isolated complementary bipolar process. It can support low-level amplification, active filtering, buffering, and instrumentation interfaces when the feedback network, load, supply bypassing, and layout follow the manufacturer’s recommendations. Exact input-offset and noise limits must be checked in the AD841 datasheet.
How should the AD841KN PCB layout be designed?
Place input, feedback, and compensation components close to the AD841KN and keep the high-speed feedback loop physically small. Connect decoupling capacitors directly to the supply pins, provide a low-impedance return path, and avoid long traces between the amplifier and its feedback components. Also keep capacitive loading off the output unless the device, load, and stability behavior have been verified together using the manufacturer application guidance.
How does the AD841KN compare with AD840 and AD842?
The three devices differ primarily in their intended minimum stable gain. The AD841 is unity-gain stable, the AD840 is stable at gain ten or greater, and the AD842 is stable at gain two or greater with 100 mA minimum output-current drive. According to the AD841 manufacturer documentation, select AD841KN for unity-gain buffers, AD840-family devices for high-gain stages, and AD842-family devices for gain-two-or-higher interfaces needing stronger drive.
Where to buy AD841KN online?
Use the Request a Quote form on this page to request AD841KN availability, order quantity, lead time, and current commercial terms. The form allows the request to be associated with the exact AD841KN MPN, including the 14-pin PDIP configuration, without relying on a generic family listing. Engineers should also confirm lifecycle status and the required temperature grade before releasing a production order.
What is the price and lead time of AD841KN?
Current AD841KN pricing and lead time should be obtained through the Request a Quote form on this page. The quote process can confirm the exact suffix, package form, manufacturing status, order quantity, and expected delivery rather than relying on a historical unit-price record. Engineers should specify the 14-pin PDIP package and any required temperature grade when requesting the quotation.

के लिए इंजीनियरिंग संदर्भ डेटा AD841KN — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the AD841KN when the circuit requires a unity-gain-stable, wideband, precision bipolar operational amplifier in a 14-pin PDIP package. It is particularly appropriate for voltage followers, low-gain sensor buffers, active filters, waveform conditioning, and instrumentation interfaces where the feedback network operates near unity gain. Select AD841KNZ, AD841ANZ, AD841BNZ, or AD841JNZ when the required temperature grade, qualification, and ordering designation differ from the original AD841KN. Use the AD842 instead when the intended gain is two or greater and the circuit benefits from its 100 mA minimum output-current drive. Use the AD840 when stable operation at gains of ten or greater is sufficient and preferred. For any substitution, verify the exact pinout, supply range, common-mode limits, output swing, offset, noise, bandwidth, slew rate, load capability, temperature range, and lifecycle status before approving the change.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद AD841KNZ AD841ANZ AD841BNZ AD841JNZ
Package 14-pin PDIP 14-pin PDIP - same 14-pin PDIP - same 14-pin PDIP - same 14-pin PDIP - same
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Core Function Wideband unity-gain-stable operational amplifier Wideband unity-gain-stable operational amplifier Wideband unity-gain-stable operational amplifier Wideband unity-gain-stable operational amplifier Wideband unity-gain-stable operational amplifier
Number of Circuits 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit
Minimum Stable Gain Unity gain Unity gain Unity gain Unity gain Unity gain
Process Technology Junction-isolated complementary bipolar process Junction-isolated complementary bipolar process Junction-isolated complementary bipolar process Junction-isolated complementary bipolar process Junction-isolated complementary bipolar process
Related AD842 Minimum Stable Gain AD842 stable at gain of 2 or greater AD842 stable at gain of 2 or greater AD842 stable at gain of 2 or greater AD842 stable at gain of 2 or greater AD842 stable at gain of 2 or greater
Related AD840 Minimum Stable Gain AD840 stable at gain of 10 or greater AD840 stable at gain of 10 or greater AD840 stable at gain of 10 or greater AD840 stable at gain of 10 or greater AD840 stable at gain of 10 or greater

मुख्य विशेषताएँ

  • Unity-gain operation (बनामAD842)
  • Broader usable gain range than AD840 (बनामAD840)
  • Same-package family migration (बनामAD841JNZ)

डिज़ाइन नोट्स

Keep the AD841KN input and feedback network close to the package and minimize the loop enclosed by the feedback components. Place the supply-bypass capacitors immediately across the positive and negative supply pins, with short ground returns. For a high-speed design, inspect the assembled board with an oscilloscope because probe grounding and long input traces can create behavior that is not represented by a simple ideal-op-amp model.

Do not select the AD841 on package similarity alone. The AD841 is unity-gain stable, while the related AD842 is stable at gains of two or greater and the related AD840 is stable at gains of ten or greater. A circuit designed around a different minimum stable gain can show ringing or unstable settling even when all three devices use a comparable footprint. Confirm the exact AD841 feedback configuration against the manufacturer guidance.

Evaluate output loading and settling rather than relying only on nominal bandwidth. Include the source impedance, feedback impedance, load capacitance, supply range, and intended closed-loop gain in the stability assessment. Extra output capacitance can disrupt transient behavior, so avoid adding long cable or capacitive loads directly to the output without checking the manufacturer’s recommended drive and compensation arrangements.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

Compliance attributes are not stated in the manufacturer product-page or datasheet excerpts associated with this listing. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status for the exact orderable suffix before production release.

डेटा सत्यापन तिथि: 2026-11-18 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

AD841KN datasheet AD841KN specifications AD841KN pinout AD841KN datasheet pdf AD841KN equivalent AD841KN replacement AD841KN cross reference AD841KN vs AD842 AD841KN vs AD840 AD841KN 14 pin PDIP AD841KN unity gain stable AD841KN price AD841KN stock Analog Devices AD841KN

संबंधित कंपोनेंट्स और शब्द

Analog Devices AD841KN AD841KNZ AD841ANZ AD841BNZ AD841JNZ AD842 AD840 Operational amplifier Voltage-feedback amplifier Wideband amplifier Precision amplifier Unity-gain stable Junction-isolated complementary bipolar process Bipolar amplifier 14-pin PDIP DIP package Through-hole package RoHS REACH AEC-Q100 Precision signal conditioning Active filtering Voltage buffer Output-current drive
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें